Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 24
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Influence of Ag on the properties of Ca0.9Yb0.1MnO3 sintered ceramics

  • Sotelo, A.
  • Torres, M.A.
  • Madre, M.A.
  • Diez, J.C.
In this study, Ca0.9Yb0.1MnO3 + x wt.% Ag (with x = 0, 1, 3, 5, and 10) thermoelectric materials were prepared via the classical ceramic method. In spite of the very high sintering temperature (1300 °C), no significant Ag losses were observed following this process. Moreover, Ag addition enhanced cation mobility during sintering due to the formation of a liquid phase. Microstructurally, it was found that Ag decreases porosity; this was confirmed by density measurements. Ag was also found to promote the formation of a Ca2Mn2O5 secondary phase. Despite the presence of this secondary phase, samples with Ag displayed lower electrical resistivity than Ag-free ones, without a drastic decrease in the absolute Seebeck coefficient. The highest thermoelectric performances, which were determined by power factor, were obtained in 1 wt.% Ag samples. These maximum values are slightly higher than the best of those reported in the literature for sintered materials with similar compositions, with the additional advantage of their being obtained using a much shorter sintering procedure.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Continuous processing of Bi2Sr2CaCu2O8+d precursor powders

  • Laliena, C.
  • Amaveda, H.
  • Özçelik, B.
  • Martínez, E.
  • de la Fuente, G.F.
  • Angurel, L.A.
A continuous solid-state process inside a roller furnace has been used to fabricate Bi-2212 powders. These powders were synthesized for their use as precursors to obtain textured monoliths by laser induced directional solidification. A thermal cycle has been defined, which depends on the length of the furnace, the prefixed temperature profile and the velocity of the sample inside the furnace. Powder properties have been studied as a function of the number of processing cycles. Phase evolution has been analyzed using X-ray diffraction, while other relevant properties of the powders, including grain size distribution, thermal behavior and temperature dependence of the AC susceptibility, have also been measured. These properties have been compared with those of commercial powders and precursors prepared using a standard solid-state protocol. Textured samples using these continuous solid-state precursors exhibit superconducting properties comparable to those similarly processed but prepared from commercial powders.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Improvement of thermoelectric properties of Ca0.9Gd0.1MnO3 by powder engineering through K2CO3 additions

  • Ferreira, N.M.
  • Ferro, M.C.
  • Sarabando, A.R.
  • Ribeiro, A.
  • Davarpanah, A.
  • Amaral, V.
  • Madre, M.A.
  • Kovalevsky, A.V.
  • Torres, M.A.
  • Costa, F.M.
  • Sotelo, A.
Oxide materials based on calcium manganite show clear prospects as thermoelectrics, provided by their stability at high temperatures and inherent flexibility in tuning the relevant electrical and thermal transport properties. Donor-doped CaMnO3 is an n-type semiconductor with a perovskite structure and relatively high thermoelectric performance. In this work, the precursor powders have been modified through potassium carbonate additions to produce Ca0.9Gd0.1MnO3 pellets without the usual delamination problems occurring during the compaction process. In order to demonstrate the relevant effects, several samples with different amounts of potassium carbonate (0–15 wt%) have been prepared. The results showed that potassium additions significantly facilitate the compaction procedure, while also improving the thermoelectric performances. The results also highlight the importance of porosity control for improving ZT, by decreasing the thermal conductivity without reduction of the electrical performance. The highest ZT values were observed for the samples processed at 15 wt% of potassium carbonate addition, exhibiting an improvement at least 30% at 800 °C when compared to the pure samples.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Effect of substrate on the microstructure and thermoelectric performances of Sr-doped Ca3Co4O9 thick films

  • Torres, M.A.
  • Mora, M.
  • Amaveda, H.
  • Madre, M.A.
  • Sotelo, A.
Ca3Co4O9 thermoelectric materials in form of thick films are very promising in practical applications due to their low costs and relatively high performance. In this work, two different suspensions have been used to produce different coatings on Al2O3 polycrystalline substrates with theoretical green thickness of 360 and 2000¿µm. Moreover, the effect of substrate has also been investigated using Al2O3 monocrystalline substrates and a 360¿µm green thickness. Sintering procedure at 900¿°C for 24¿h has drastically decreased coating thickness. XRD performed on the coatings surface has shown the formation of small amounts of Ca3Co2O6 secondary phase on the polycrystalline substrates, while it was more abundant, and accompanied by Ca2Co2O5 on the monocrystalline substrates. In spite of the higher secondary phases content, monocrystalline substrates produced a slight grain orientation which led to the highest thermoelectric properties between the samples (0.38¿mW/K2m at 800¿°C), and very close to the best reported values in the literature.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Significant enhancement of the thermoelectric performance in Ca3Co4O9 thermoelectric materials through combined strontium substitution and hot-pressing process

  • Torres, M.A.
  • Costa, F.M.
  • Flahaut, D.
  • Touati, K.
  • Rasekh, S.
  • Ferreira, N.M.
  • Allouche, J.
  • Depriester, M.
  • Madre, M.A.
  • Kovalevsky, A.V.
  • Diez, J.C.
  • Sotelo, A.
This work explores the possibilities for a further enhancement of the thermoelectric properties of Ca3Co4O9 by Sr-doping combined with hot-pressing. Modified hot-pressing process resulted in highly-textured and dense ceramics. Sr-doping significantly improves electrical properties, resulting in extremely large power factor (1.2 mW/K2m at 800 °C) due to simultaneous electrical resistivity decrease and Seebeck coefficient increase. The main effect on cumulative electrical performance is provided by the Seebeck coefficient, reaching 270µV/K at 800 °C. XPS revealed relatively high average cobalt oxidation state at room temperature (+3.3), compared to materials produced by conventional sintering. The results of combined XPS and Auger electron spectroscopy emphasize the importance of high densification in Ca3Co4O9-based ceramics for preventing phase decomposition and interaction with CO2 and moisture. Still, despite the exceptional electrical performance, the calculated figure-of-merit (estimated as 0.29 at 800 °C) is around the best reported in the literature due to a high thermal conductivity (4.4 W/K m at room temperature).
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Improving thermoelectric properties of Ca 3 Co 4 O 9+d through both Na doping and K addition at optimal values

  • Özkurt, B.
  • Aytekin, M.E.
  • Madre, M.A.
  • Sotelo, A.
  • Torres, M.A.
Ca 2.93 Na 0.07 Co 4 O y /x wt% K 2 CO 3 (x = 0.00, 0.01, and 0.03) polycrystalline ceramics were prepared by conventional solid-state method. XRD results have shown that all samples predominantly include Ca 3 Co 4 O 9 phase together with small amounts of secondary phases. SEM images show that all samples have randomly oriented plate-like grains in different sizes. The electrical resistivity measurement showed that electrical properties of Ca 3 Co 4 O 9 ceramics can be improved significantly by both, Na doping and K addition at their optimal values. The effect of dopants on thermoelectric properties of Ca 3 Co 4 O 9 was examined by both, Seebeck coefficient and power factor, being higher in K-added than in the pure samples, indicating that thermoelectric properties of samples are positively affected when alkaline elements enter into their structure.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Low temperature thermoelectric properties of K-substituted Bi 2 Sr 2 Co 2 O y ceramics prepared via laser floating zone technique

  • Özçelik, B.
  • Çetin, G.
  • Gürsul, M.
  • Madre, M.A.
  • Sotelo, A.
  • Adachi, S.
  • Takano, Y.
In the present study, Bi 2 Sr 2-x K x Co 2 O y (x = 0.0, 0.050, 0.075, 0.100, and 0.15) ceramic precursors have been produced using the classical ceramic route, followed by texturing through the laser floating zone technique. XRD results show that the thermoelectric phase is the major one in all cases. Moreover, K-substitution decreases the secondary phases content, when compared to the undoped sample. SEM observations indicate that grain orientation is significantly enhanced when K-content is increased. K-doping decreases electrical resistivity from 32 10 -5 O m (in undoped samples) to 20–22 10 -5 O m at 300 K, while increasing Seebeck coefficient from 55 µV/K to 100–117 µV/K at 300 K. On the other hand, thermal conductivity is slightly lower in undoped samples (0.93 W/K m, compared to 1.10–1.28 W/K m for doped ones at 300 K), due to their lower electrical conductivity. Finally, ZT values are higher when the K-content increases up to x = 0.10, reaching 0.029 at around 400 K, and slightly decreasing for higher doping levels.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Electromagnetic behaviour and thermal stability of a conduction-cooled, no-insulated 2G-HTS coil at intermediate temperatures

  • Cubero, A.
  • Núñez-Chico, A.B.
  • Navarro, R.
  • Angurel, L.A.
  • Martínez, E.
The electromagnetic and thermal properties of a double pancake coil made of second generation high temperature superconductor, 2G-HTS, have been studied. The coil was wound with no-insulation between turns (NI coil) and was later impregnated with epoxy resin and glued to a copper support plate. The coil was thermally anchored to the cryocooler cold finger and cooled by conduction. After several thermal cycles no degradation of its superconducting properties was observed. The coil was operated under high vacuum and high currents (up to 400 A in steady conditions) at different temperatures in the range between 5 K and 77 K, with special focus on the analysis above 30 K. The charge and discharge characteristics, and the experimentally measured and numerically estimated critical currents, have been studied. The different loss contributions during current ramp and the thermal contact conductance between different parts of the double pancake coil have been measured. The implications of these two factors on the thermal stability and the behaviour of the whole cryogenic system are discussed.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Fabrication of cylindrical active GRIN media by laser-assisted radial dopant diffusion: A proof of concept

  • Gómez-Varela, A.I.
  • Rey-García, F.
  • de Francisco, I.
  • Flores-Arias, M.T.
  • de la Fuente, G.F.
  • Bao-Varela, C.
This work introduces a new approach to prepare active GRadient-INdex (GRIN) materials by gradually doping commercial silica cylindrical substrates with different optically active ions or materials by the Laser Zone Melting (LZM) process. Scanning Electron Microscopy (SEM) combined with energy dispersive X-ray (EDX) analysis demonstrate that the dopants are gradually incorporated into the cylindrical substrate under controlled penetration depths. This simple, environmentally respectful fabrication method opens the possibility to manufacture versatile GRIN optical elements on a large scale and reduced cost.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Effect of annealing and potassium substitution on the thermoelectric and magnetic properties of directionally grown Bi 2 Sr 2 Co 2 O y ceramics

  • Cetin, G
  • Ozcelik, B
  • Gursul, M
  • Torres, Miguel Ángel
  • Madre, María A
  • Sotelo, Andrés
Bi2Sr2-xKxCo2Oy (x = 0.0, 0.025, 0.050, 0.075, 0.100, 0.125, and 0.15) ceramic materials have been fabricated using a classical ceramic process, followed by texturing through directional solidification. SEM analysis of samples, before and after annealing has shown that grains were aligned along the growth direction. While as-grown samples have several phases, besides the thermoelectric one, the annealed ones show much higher thermoelectric phase content. In addition, K-substitution increases the thermoelectric phase content and enhances grain orientation. These improvements decrease the electrical resistivity without significant changes in Seebeck coefficient. The maximum power factor value for 0.10K-substituted annealed samples has been found as 0.20 mW/K2 m. This is superior to the highest reported for hot-pressed materials. However, all samples have similar magnetic properties.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

High speed processing of NiFe2O4 spinel using a laser furnace

  • Özçelik, B.
  • Özçelik, S.
  • Amaveda, H.
  • Santos, H.
  • Borrell, C.J.
  • Sáez-Puche, R.
  • de la Fuente, G.F.
  • Angurel, L.A.
The Laser Furnace (LF) method has been applied to directionally solidify NiFe2O4 spinel disks from a mixture of Fe and Ni oxides in order to obtain uniform, dense targets for controlled synthesis of spinel nanoparticles via Laser Ablation. Application of a CO2 laser in Line Scan mode onto a sample with the desired stoichiometry, enabled melt processing above 1580 °C at its outer surface layer. This process was carried out inside a continuous roller furnace at a maximum volume temperature of 1000 °C. Such combination helps avoid excessive thermal stress, crack formation and catastrophic failure of these magnetic ceramic monoliths. Higher energy incubation values yield increased molten volumes and a thicker resolidified surface layer with a dense microstructure. Despite the high solidification rates imposed, NiFe2O4 spinel is the main phase obtained according to X-Ray Diffraction (XRD) and magnetization studies. LF processed samples exhibit a reduction of the coercive fields and an increase of the saturation magnetization values, evidence for soft ferromagnetism and characteristic of the magnetic behaviour associated with this spinel. This work demonstrates the convenience of the LF method for preparation of uniform, dense targets for Laser Ablation and other evaporation based techniques used in the fabrication of nanoparticles.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Tuning Ca3Co4O9 thermal and transport properties by TiC nanoparticles addition

  • Amaveda, H.
  • Dura, O.J.
  • Mora, M.
  • Torres, M.A.
  • Guelou, G.
  • Madre, M.A.
  • Marinel, S.
  • Sotelo, A.
Ca3Co4O9 + xwt.% TiC (x = 0, 0.25, 0.5, 0.75, and 1.0) polycrystalline thermoelectric ceramics have been prepared through the classical ceramic route. XRD characterization has demonstrated that all samples are mainly composed by the Ca3Co4O9 phase, while microstructural observation has shown that no reaction between both components has been produced. Moreover, TiC particles are well distributed for small additions, and start to agglomerate from 0.75 wt.% content. Density measurements showed that nearly no changes have been produced by TiC addition and nearly the whole porosity appears as open one. Furthermore, electrical resistivity decreases up to 0.75 wt.% addition, increasing for higher content. On the other hand, Seebeck coefficient has been maintained unchanged in all samples. In spite of an irregular behaviour of thermal conductivity with temperature, it tends to decrease when the temperature is raised, displaying the lowest values for the 0.25 wt.% samples. These data led to an increase of about 40% in ZT values at 800 °C for samples with 0.25 wt.% addition, when compared with the pure ones. Finally, linear thermal expansion coefficient is decreased when TiC content is increased, which can be exploited to fit the thermal expansion coefficients of all the components used to build a power generation thermoelectric module.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Detail investigation of thermoelectric performance and magnetic properties of Cs-doped Bi2Sr2Co2Oy ceramic materials

  • Özçelik, B.
  • Gürsul, M.
  • Çetin, G.
  • Özçelik, C.
  • Torres, M.A.
  • Madre, M.A.
  • Sotelo, A.
Bi2Sr2-xCsxCo2Oy materials with 0 = x = 0.15, have been fabricated via the classical ceramic technique. XRD results have indicated that undoped and Cs-substituted samples are composed of Bi2Sr2Co2Oy phase as the major one. Microstructural studies have demonstrated the formation of a liquid phase, which allows a drastic grain growth. This factor is responsible for a drastic improvement of relative density, reaching about 95% of the theoretical one for 0.125 Cs content. On the other hand, electrical resistivity has been reduced up to 14 mO cm at 650 °C for 0.125 Cs content, around 40% lower than the obtained in undoped samples. As a consequence, Seebeck coefficient has been decreased due to the raise in charge carrier concentration. The highest power factor at 650 °C (0.21 mW/K2 m) has been found for 0.125 Cs substituted sample, about 40% larger than the obtained in undoped samples, and very similar to the notified in single crystals (0.26 mW/K2 m). Magnetisation with respect to temperature results have demonstrated that measured samples have a paramagnetic property above 50 K, except 0.10 Cs. Magnetic hysteresis curves have shown that the slopes and the magnitudes have increased with decreasing temperature.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Improvement of grain alignment in Bi2Sr2Co1.8Oy thermoelectric through the electrically assisted laser floating zone

  • Ferreira, N.M.
  • Madre, M.A.
  • Torres, M.A.
  • Davarpanah, A.
  • Amaral, V.
  • Costa, F.M.
  • Sotelo, A.
Thermoelectric performances of cobaltite ceramics were improved by increasing grain sizes and alignment through the Electrically Assisted Laser Floating Zone method. Bi2Sr2Co1.8Oy ceramics were directionally grown at 30 mm/h, applying external DC (0-500 mA) during the growth process. Microstructure and thermoelectric properties are significantly influenced by the external current direction and intensity. Negative currents/pole on the seed rod prevent the formation of thermoelectric phase, while positive pole on the seed rod, decreases the amount of secondary phases and increase grain orientation when compared to samples grown without current. Annealing procedure decreases secondary phases content, without modifying grain alignment. The best thermoelectric performances were obtained for samples grown with +300 mA, reaching the highest ZT values of 0.09 at 650 °C. Moreover, it should be highlighted that these processed samples can be directly applied in thermoelectric modules, avoiding the long and expensive steps necessary when other preparation processes are used.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Preparation, structural characteristics and optical parameters of the synthesized nano-crystalline sulphur-doped Bi2Te2.85Se0.15 thermoelectric materials

  • Shalaby, M.S.
  • Hashem, H.M.
  • Yousif, N.M.
  • Zayed, H.A.
  • Sotelo, A.
  • Wahab, L.A.
In the present work, a systematic preparation of Bi2Te2.85Se0.15-xSx (x = 0.0, 0.02, 0.04 and 0.06) compositions was carried out by solvothermal method. The materials were characterized by XRD, SEM, EDX, TEM and Raman spectroscopy. XRD, as well as TEM, to confirm the nanostructure of samples. The electrical and thermal properties were investigated in the temperature range from room temperature to 600 K. The highest power factor was 1.3 × 10-2 mW/K2 m at 600 K for (x = 0.06) sample. This improvement in the thermoelectric properties may be due to the ordered atomic arrangement of Bi, Te, and Se induced by sulphur in the Bi2Te2.85Se0.15-xSx nanocomposites, which was confirmed by X-ray diffraction and Raman spectral analysis. The optical properties, such as energy gap, refractive index, extinction coefficient and dielectric constants, were obtained from the diffused reflectance data in the range of 200 to 800 nm. Sulphur doping influences the optical energy gap, reaching the lowest value for x = 0.04 samples (0.14 eV), while the highest allowed energy gap was found in x = 0.06 ones (0.41 eV). Also, It should be mentioned that dielectric constants (er and ei) were affected due to Sulphur doping, whereas the samples with x = 0.04 and 0.02 have the highest and lowest er, respectively, and the opposite for ei when increasing the wavelength.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Drastic enhancement of mechanical properties of Ca3Co4O9 by B4C addition

  • Amaveda, H.
  • Mora, M.
  • Dura, O.J.
  • Torres, M.A.
  • Madre, M.A.
  • Marinel, S.
  • Sotelo, A.
Ca3Co4O9 with B4C additions in different proportions (0, 0.10, 0.25, 0.5, and 0.75 wt.%) have been fabricated using the classical solid-state method. Powder XRD patterns have displayed that Ca3Co4O9 phase is the major one in all samples. Microstructural observations showed that B4C has been superficially oxidized, producing liquid B2O3 during sintering, and reacting with the Ca3Co4O9 grains to produce bridges between them. In spite of the increase of porosity, these bridges led to an important raise (more than two times) of mechanical properties when compared to the pristine materials. On the other hand, while B4C addition has not influenced S values, it has decreased electrical resistivity, thermal conductivity, and thermal expansion. Consequently, ZT values have been also increased, reaching 0.24 at 800 °C in 0.25 wt.% B4C containing samples, which is very close to the best values reported in the literature, and two times higher than the obtained in pure materials in this work.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Drastic modification of low temperature thermoelectric properties of Na-doped Bi2Sr2Co2Oy ceramics prepared via laser floating zone technique

  • Çetin, G.
  • Özçelik, B.
  • Gürsul, M.
  • Madre, M.A.
  • Sotelo, A.
  • Adachi, S.
  • Takano, Y.
In this study, Bi2Sr2-xNaxCo2Oy (x = 0.0, 0.05, 0.075, 0.10, and 0.15) ceramic powders have been fabricated via the classical ceramic route, followed by a texturing process through the laser floating zone technique. XRD patterns show the thermoelectric phase as the major one. In addition, Na-substitution reduces the amount of secondary phases, when compared to the pure sample. SEM observations point out that grain orientation is significantly improved when Na-content is increased. Na-substitution reduces electrical resistivity from 35 (in pure samples) to 19.6 mO cm (in Na = 0.05 ones) at around room temperature, while Seebeck coefficient is, approximately, twice measured in Na-free. On the other hand, thermal conductivity is slightly lower in undoped samples (0.83 W/K m), when compared to the Na-substituted ones (1.10–1.40 W/K m) at room temperature, due to their lower electrical conductivity. Finally, ZT values are higher when the Na-content is increased, reaching 0.022 at around 400 K.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Tuning thermoelectric properties of Ca0.9Gd0.1MnO3 by laser processing

  • Ferreira, N.M.
  • Sarabando, A.R.
  • Ferro, M.C.
  • Madre, M.A.
  • Dura, O.J.
  • Sotelo, A.
Donor-doped CaMnO3 is an n-type semiconductor with perovskite structure, being considered as a potential n-type leg in thermoelectric modules. This oxide presents stability at high temperatures and allows tuning the relevant electrical and thermal transport properties through doping. In this work, Ca0.9Gd0.1MnO3 precursors have been prepared to produce fibres through the laser floating zone technique using different pulling rates. However, as-grown fibres did not present thermoelectric properties due to the presence of high amounts of secondary phases, leading to very high electrical resistivity values. The results have highlighted the importance of annealing procedures to reduce electrical resistivity, due to the decrease of secondary phases amount, and producing promising thermoelectric performances. The annealed samples present higher ZT values when the growth rate is decreased, reaching around 0.22 for the lowest growth rate, which is very close to the best values reported in the literature for these materials. Moreover, this procedure possesses an additional advantage considering that these samples can be directly used as n-type legs in thermoelectric modules for high-temperature applications. However, further studies should be made to determine the optimal amount of dopant.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

U-type unileg thermoelectric module: A novel structure for high-temperature application with long lifespan

  • Wang, Xue
  • Wang, Hongchao
  • Su, Wenbing
  • Chen, Tingting
  • Tan, Chang
  • Madre, María A.
  • Sotelo, Andres
  • Wang, Chunlei
Strong thermal stress caused by high temperature and difference of thermal expansion coefficient (CTE) will negatively influence the lifespan of the thermoelectric module. In this work, a new high-temperature CaMnO3-based U-type unileg thermoelectric module, combining a unileg structure with pn-junction, is proposed and investigated. The novel design avoids the device failure due to different CTEs and high temperature gradients. As a result, the maximal thermal stress (σmax,TEM) of 3.31 GPa and fatigue life of 41686 cycles are 46 % and 132 % of those of traditional modules at 6 W and 300 K, respectively. To further relieve stress concentration, the effect of rounded corners (ru, rl), Ag layer thickness (HAg) and length of right legs (LR), have been studied. It has been found that larger ru, and rl are suitable to relieve the local stress concentration, and the lowest σmax,TEM and highest power (Pmax) are achieved at (ru,rl)=(0.1,0) and (0,0.5). Moreover, larger LR and HA are beneficial for mechanical properties by decreasing the peak stress and dispersing the high thermal stress regions, while module performance is improved at lower LR and HAg. Results obtained from this U-type unileg thermoelectric module should influence and guide the design and optimization of high-temperature thermoelectric generators.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

IR laser line scanning treatments to improve levitation forces in MgTi0.06B2 bulk materials

  • Ozturk, K.
  • Aksoy, C.
  • Angurel, L.A.
  • Savaskan, B.
  • Martínez, E.
  • Badía-Majós, A.
  • de la Fuente, G.F.
  • Guner, B.
  • Dancer, C.E.J.
  • Celik, S.
Infrared (IR) laser-line scanning has been widely used to induce different surface microstructures in a broad range of materials. In this work, this laser configuration was applied on the surface of MgTi0.06B2 bulk samples in order to ascertain its effects on their superconducting properties, particularly on the magnetic levitation forces. The microstructural changes produced by this type of laser treatment were investigated by X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM). It was observed that the thermal treatment induced by the laser improves grain connectivity in a layer of material just below the irradiated surface, in agreement with the observed improvement in critical current density values, Jc, which were estimated from isothermal magnetic hysteresis loops. A significant increment of both vertical (Fz) and lateral (Fx) magnetic levitation forces was achieved. Numerical calculations were performed to understand the experimental behaviour and to clarify how an improvement of Jc near the surface can improve the magnetic levitation force of these materials. In addition, the same studies were carried out in similar bulk samples but with nano-sized silver particle additions of 3 and 6 wt %, in the outer ring of the bulk, observing also an improvement of the levitation forces, albeit less than in samples without Ag because of the better performance of the original samples after laser treatment. These results are relevant to those studying superconductor fabrication and material fabrication modelling, essential for the development of technological applications of superconductors, and are based on microstructure control via application of a recently developed laser-line scan method.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

MgB(2)cables made of thin wires manufactured by IMD process

  • Kovac, P
  • Kopera, L
  • Hain, M
  • Martinez, E
  • Kovac, J
  • Melisek, T
  • Berek, D
  • Husek, I
This paper presents the properties of cables made of thin MgB(2)wires with different sheaths manufactured by IMD process. Strong effect of the outer sheath on theJ(e)(B) performance was observed and the best properties were obtained for the strongest Cu sheath. It was found that the transversal and longitudinal cables uniformity affects the critical currents in MgB(2)wires made by IMD considerably. We have analyzed the quench dynamics in Rutherford cables with Al + 1.5%A(l2)O(3)sheath, when subjected to heat disturbances. Quench triggered in the strands in direct contact with the heater, observing important delays in quench development among strands. Low AC losses were measured for the extra-light Rutherford cable with Ti barrier and Al + 1.5%Al(2)O(3)sheath due to an increased barrier resisitivity and surface Al sheath oxidation, which reduces coupling current loss component effectivelly.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Effects of laser-induced periodic surface structures on the superconducting properties of Niobium

  • Cubero, A.
  • Martínez, E.
  • Angurel, L. A.
  • de la Fuente, G. F.
  • Navarro, R.
  • Legall, H.
  • Krüger, J.
  • Bonse, J.
It is well known that the use of ultrashort (fs) pulsed lasers can induce the generation of (quasi-) periodic nanostructures (LIPSS, ripples) on the surface of many materials. Such nanostructures have also been observed in sample''s surfaces irradiated with UV lasers with a pulse duration of 300 ps. In this work, we compare the characteristics of these nanostructures on 1-mm and on 25-µm thick niobium sheets induced by 30 fs n-IR and 300 ps UV pulsed lasers. In addition to conventional continuous or burst mode processing configurations, two-dimensional laser beam and line scanning modes have been investigated in this work. The latter allows the processing of large areas with a more uniform distribution of nanostructures at the surface. The influence of the generated nanostructures on the superconducting properties of niobium has also been explored. For this aim, magnetic hysteresis loops have been measured at different cryogenic temperatures to analyse how these laser treatments affect the flux pinning behaviour and, in consequence, the superconductor''s critical current values. It was observed that laser treatments are able to modify the superconducting properties of niobium samples. © 2019 The Author(s)
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Simulation of salt spray corrosion behaviour of micro-arc oxidation coating by laser induced Ag infiltration

  • Liu, C.
  • Li, H.
  • Cai, H.
  • Angurel, L.A.
  • De La Fuente, G.F.
  • Jiang, B.
Micro-arc oxidation (MAO) coating was initially prepared on 6061 Al alloy, and subsequently coated with Ag using magnetron sputtering. Laser beam scan (LBS) treatments were then applied to infiltrate the sputtered Ag into the MAO coating in order to simulate the corrosion behaviour of the MAO coating during the neutral salt spray test (NSST). Cross-sectional morphologies and Ag element distribution maps were studied by using the field emission scanning electron microscopy (FESEM) on the MAO-Ag coated samples after LBS infiltration. The results showed that there existed the micro-cracks with tree-root or lightning shape within the MAO coating. Interconnected aggregates, including micro-pores, large cavities far beneath the surface and tree-root like micro-cracks, served as complex corrosion channels during salt spray corrosion. Through these corrosion channels, the salt spray penetrated gradually into the interface between the MAO coating and the original Al substrate, thus causing corrosion of the Al substrate during the NSST. The LBS treatment is presented as a method to explore the subtle micro-crack and pore channels associated to the MAO coating and to provide information that paves the way towards understanding of corrosion phenomena in these porous systems.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Experimental and Numerical Investigation of Levitation Force Parameters of Novel Multisurface Halbach HTS-PMG Arrangement for Superconducting Maglev System

  • Ozturk K.
  • Badia-Majos A.
  • Abdioglu M.
  • Dilek D.B.
  • Gedikli H.
We have designed multisurface Halbach high temperature superconductor-permanent magnetic guideway (HTS-PMG) arrangements for magnetically levitated transportation (Maglev) and investigated the static force parameters in addition to the dynamic response characteristics. Three different Halbach HTS-PMG arrangements were used with multisurface (6 HTS, 4 HTS) and single surface (2 HTS) configurations and static and dynamic measurements were carried out in three different field cooling heights (FCHs). The bigger vertical loading capacity and wider loading gap were obtained with multisurface Halbach HTS-PMG arrangements. In addition, nearly four times bigger guidance force values of multisurface arrangements than that of single surface one indicates that the side HTSs in multisurface arrangements make a significant contribution to the guidance force and thus lateral movement stability of Maglev systems. Both the vertical and lateral dynamic stiffness values increased with decreasing FCH and it can be also said that the dynamic stiffness properties of Maglev systems can be enhanced especially in lateral direction by using the multisurface Halbach HTS-PMG arrangements. Understanding of these experimental observations is supported by dedicated theoretical modelling through a 2-D approximation of the system. We show that by using a single material parameter (the critical current density ${{\boldsymbol{J}}_{{\bf c}}}$) for the whole superconducting set, one may satisfactorily predict the complete series of experiments. The static and dynamic parameters obtained from this study and the results of dedicated theoretical modeling for single-surface and multisurface HTS-PMG arrangements are thought to be helpful for the researchers working on static and dynamic performances of HTS Maglev systems. © 2002-2011 IEEE.