Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 49
Encontrada(s) 1 página(s)

Dipòsit Digital de la UB
Publication Artículo científico (JournalArticle)

Hubs and clusters approach to unlock the development of carbon capture and storage - Case study in Spain

  • Sun, Xiaolong
  • Alcalde Martín, Juan
  • Bakhtbidar, M.
  • Elío, J.
  • Vilarrasa, V.
  • Canal, J.
  • Ballesteros, J.
  • Heinemann, N.
  • Haszeldine, S.
  • Cavanagh, A.
  • Vega-Maza, D.
  • Rubiera, F.
  • Martínez-Orio, R.
  • Johnson, G.
  • Carbonell, R.
  • Marzán, I.
  • Travé i Herrero, Anna
  • Gómez Rivas, Enrique
Many countries have assigned an indispensable role for carbon capture and storage (CCS) in their national climate change mitigation pathways. However, CCS deployment has stalled in most countries with only limited commercial projects realised mainly in hydrocarbon-rich countries for enhanced oil recovery. If the Paris Agreement is to be met, then this progress must be replicated widely, including hydrocarbon-limited countries. In this study, we present a novel source-to-sink assessment methodology based on a hubs and clusters approach to identify favourable regions for CCS deployment and attract renewed public and political interest in viable deployment pathways. Here, we apply this methodology to Spain, where fifteen emission hubs from both the power and the hard-to-abate industrial sectors are identified as potential CO2 sources. A priority storage structure and two reserves for each hub are selected based on screening and ranking processes using a multi-criteria decision-making method. The priority source-to-sink clusters are identified indicating four potential development regions, with the North-Western and North-Eastern Spain recognised as priority regions due to resilience provided by different types of CO2 sources and geological structures. Up to 68.7 Mt CO2 per year, comprising around 21% of Spanish emissions can be connected to clusters linked to feasible storage. CCS, especially in the hard-to-abate sector, and in combination with other low-carbon energies (e.g., blue hydrogen and bioenergy), remains a significant and unavoidable contributor to the Paris Agreement's mid-century net-zero target. This study shows that the hubs and clusters approach can facilitate CCS deployment in Spain and other hydrocarbon-limited countries.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Induced seismicity in geologic carbon storage

  • Vilarrasa, Víctor
  • Carrera, Jesús
  • Olivella, Sebastià
  • Rutqvist, Jonny
  • Laloui, Lyesse
Geologic carbon storage, as well as other geoenergy applications, such as geothermal energy, seasonal natural gas storage and subsurface energy storage imply fluid injection and/or extraction that causes changes in rock stress field and may induce (micro)seismicity. If felt, seismicity has a negative effect on public perception and may jeopardize wellbore stability and damage infrastructure. Thus, induced earthquakes should be minimized to successfully deploy geo-energies. However, numerous processes may trigger induced seismicity, which contribute to making it complex and translates into a limited forecast ability of current predictive models.We review the triggering mechanisms of induced seismicity. Specifically, we analyze (1) the impact of pore pressure evolution and the effect that properties of the injected fluid have on fracture and/or fault stability; (2) non-isothermal effects caused by the fact that the injected fluid usually reaches the injection formation at a lower temperature than that of the rock, inducing rock contraction, thermal stress reduction and stress redistribution around the cooled region; (3) local stress changes induced when lowpermeability faults cross the injection formation, which may reduce their stability and eventually cause fault reactivation; (4) stress transfer caused by seismic or aseismic slip; and (5) geochemical effects, which may be especially relevant in carbonate-containing formations. We also review characterization techniques developed by the authors to reduce the uncertainty in rock properties and subsurface heterogeneity both for the screening of injection sites and for the operation of projects. Based on the review, we propose a methodology based on proper site characterization, monitoring and pressure management to minimize induced seismicity., Víctor Vilarrasa acknowledges funding from the European Research Council (ERC) under the European Union’s Horizon 2020 Research and Innovation Programme (grant agreement no. 801809). Jonny Rutqvist acknowledges funding by the Assistant Secretary for Fossil Energy, National Energy Technology Laboratory, National Risk Assessment Partnership of the U.S. Department of Energy to the Lawrence Berkeley National Laboratory under contract no. DEAC02-05CH11231., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Geomechanics and Fluid Flow in Geothermal Systems

  • Vilarrasa, Víctor
  • Makhnenko, Roman Y.
  • Parisio, Francesco
Geothermal systems, including hydrothermal systems [1], enhanced geothermal systems (EGS) [2], and superhot or supercritical systems [3–5], are receiving an increasing interest because they provide carbon-free energy that is necessary to shift the current dependency on fossil fuels and thus significantly reduce CO2 emissions to the atmosphere [6]. Geothermal energy can potentially provide continuous energy output without daily or seasonal fluctuations—a strong advantage when compared to other renewable sources—and negative emissions if CO2 is used as the working fluid [7–9]. However, the deployment of geothermal systems is being hindered by insufficient permeability of the reservoir rock [10], excessive induced seismicity during reservoir stimulation [11], and geochemical reactions accelerated by high temperature that lead to corrosion and scaling [12]. To overcome these challenges, interdisciplinary approaches that investigate relevant processes occurring during geothermal energy exploitation are necessary. The focus of this special issue is on geomechanical aspects of geothermal systems, including coupled processes occurring in multiphase systems, experimental characterization of rock and inelastic deformation that may induce seismicity, and geochemistry of geothermal systems. This special issue compiles the most recent advances in geothermal energy and combines the complex interactions between geomechanics, fluid flow, and geochemical reactions., The guest editors thank all the authors of this special issue and their perseverance during the publication process. We also thank the many anonymous reviewers who helped to evaluate and contributed to these papers. The guest editors would also like to acknowledge their sources of funding. V.V. acknowledges funding from the European Research Council (ERC) under the European Union’s Horizon 2020 Research and Innovation Programme through the Starting Grant GEoREST, grant agreement No. 801809 (http://www.georest.eu). R.M. is thankful for the support provided by the UIUC-ZJU Research Collaboration program (grant # 083650). The contribution of F.P. is funded by the Deutsche Forschungsgemeinschaft (DFG, German Research Foundation)—project number PA 3451/1-1., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Impacts of natural CO2 leakage on groundwater chemistry of aquifers from the Hamadan Province, Iran

  • Delkhahi, Behzad
  • Nassery, Hamid Reza
  • Vilarrasa, Víctor
  • Alijani, Farshad
  • Ayora, Carlos
The effect of natural CO2 leakage through water wells on groundwater chemistry from alluvial aquifers of Hamadan, Iran, has been investigated through analysis of water samples from 5 springs and 19 wells. The average CO2 partial pressure in gas charged groundwater has increased about 32 times with respect to background groundwater, leading to an increase in alkalinity and in the concentration of all ions, except for SO4, and to a decrease in pH and DO. Due to a high pH buffering capacity, pH of gas charged groundwater has decreased only one unit. The increase in salinity of the gas charged groundwater cannot be attributed to in situ weathering of aquifer materials because of (1) the lack of correlation between DIC vs δ13CDIC and TDS vs pH, (2) the high concentration of SiO2 and F and (3) the 87Sr/86Sr ratio in the range from 0.7085 to 0.7118. Instead, it can be attributed to saline CO2-rich waters from deep sources, which can dissolve a variety of minerals during their migration towards the surface. Although it is not clear the role of CH4 as electron donor, the association of δ18OSO4 and δ34SSO4 with SO4 concentration suggests that sulfate reduction could occur in the environment. The salinity of Mesozoic gas-rich springs, which present higher CO2 pressure and lower pH, is five times lower than that of Cenozoic ones because of the different degrees of metamorphism, which lead to an increase in grain size and slower reaction rate in Mesozoic than in Cenozoic carbonate rocks., B.D. acknowledges the financial support received from the “Iran’s Ministry of Science, Research and Technology, Iran” (Ph.D. students’ sabbatical grants), Hamadan regional water company and Geological survey of Iran. V.V. acknowledges funding from the European Research Council (ERC) under the European Union’s Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (www.georest.eu), grant agreement No. 801809. The authors thank for technical and human support provided by SGIker of UPV/EHU and European funding (ERDF and ESF)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Special Issue “Observations of Coupled Processes in Fractured Geological Media at Various Space and Time”

  • Min, Ki-Bok
  • Rutqvist, Jonny
  • Vilarrasa, Víctor
This Special Issue originates from selected contributions at the International Conference on Coupled Processes in Fractured Geological Media: Observation, Modeling, and Application (CouFrac2018). CouFrac2018 has been the first CouFrac conference focusing on coupled processes in fractured media, providing a platform for international discussion, communication and networking on this emerging topic. The conference was held in Wuhan, China, between 12 and 14th of November, 2018., K.-B.M. acknowledges support from the Institute of Engineering Research, Seoul National University. J.R. acknowledges support from the U.S. Department of Energy to the Lawrence Berkeley National Laboratory under contract No. DE-AC02-05CH11231. V.V. acknowledges funding from the European Research Council (ERC) under the European Union’s Horizon 2020 Research and Innovation Programme through the Starting Grant GEoREST, grant agreement No. 801809 (www.georest.eu)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Sinking CO2 in Supercritical Reservoirs

  • Parisio, Francesco
  • Vilarrasa, Víctor
Geologic carbon storage is required for achieving negative CO2 emissions to deal with the climate crisis. The classical concept of CO2 storage consists in injecting CO2 in geological formations at depths greater than 800 m, where CO2 becomes a dense fluid, minimizing storage volume. Yet CO2 has a density lower than the resident brine and tends to float, challenging the widespread deployment of geologic carbon storage. Here, we propose for the first time to store CO2 in supercritical reservoirs to reduce the buoyancy‐driven leakage risk. Supercritical reservoirs are found at drilling‐reachable depth in volcanic areas, where high pressure (p > 21.8 MPa) and temperature (T > 374°C) imply CO2 is denser than water. We estimate that a CO2 storage capacity in the range of 50–500 Mt yr−1 could be achieved for every 100 injection wells. Carbon storage in supercritical reservoirs is an appealing alternative to the traditional approach., The authors acknowledge funding from the European Research Council (ERC) under the European Union's Horizon 2020 Research and Innovation Programme through the Starting Grant GEoREST (www.georest.eu), grant agreement No. 801809 and the support by the Spanish Ministry of Science and Innovation (Project CEX2018‐000794‐S); F. P. acknowledges funding from the Deutsche Forschungsgemeinschaft (DFG, German Research Foundation)—project number PA 3451/1‐1., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Analytical Solution to Assess the Induced Seismicity Potential of Faults in Pressurized and Depleted Reservoirs

  • Wu, Haiqing
  • Vilarrasa, Víctor
  • De Simone, Silvia
  • Saaltink, Maarten W.
  • Parisio, Francesco
Displaced faults crossing the reservoir could significantly increase the induced earthquake frequency in geo‐energy projects. Understanding and predicting the stress variation in such cases is essential to minimize the risk of induced seismicity. Here, we adopt the inclusion theory to develop an analytical solution for the stress response to pore pressure variations within the reservoir for both permeable and impermeable faults with offset ranging from zero to the reservoir thickness. By analyzing fault stability changes due to reservoir pressurization/depletion under different scenarios, we find that (1) the induced seismicity potential of impermeable faults is always larger than that of permeable faults under any initial and injection conditions—the maximum size of the fault undergoing failure is 3–5 times larger for impermeable than for permeable faults; (2) stress concentration at the corners results in the occurrence of reversed slip in normal faults with a normal faulting stress regime; (3) while fault offset has no impact on the slip potential for impermeable faults, the slip potential increases with the offset for permeable faults, which indicates that non‐displaced permeable faults constitute a safer choice for site selection; (4) an impermeable fault would rupture at a lower deviatoric stress, and at a smaller pressure buildup than a permeable one; and (5) the induced seismicity potential is overestimated and the injectivity underestimated if the stress arching (i.e., the poromechanical coupling) is neglected. This analytical solution is a useful tool for site selection and for supporting decision making during the lifetime of geo‐energy projects., H. Wu acknowledges the financial support received from the AGAUR (Generalitat de Catalunya) through the ‘‘grant for universities and research centers for the recruitment of new research personnel (FI‐2019)''. V. Vilarrasa acknowledges funding from the European Research Council (ERC) under the European Union's Horizon 2020 Research and Innovation Programme through the Starting Grant GEoREST (www.georest.eu), Grant agreement no. 801809. V. Vilarrasa also acknowledges support by the Spanish Ministry of Science and Innovation (Project CEX2018‐000794‐S). S.D. Simone acknowledges financial support from the SAD2018 project funded by the Brittany Region and from ANR LabCom Project eLabo ANR‐17‐LCV2‐0012. M. Saaltink acknowledges financial support from the “HEATSTORE” project (170153–44011), which has been subsidized through the ERANET Cofund GEOTHERMICA (Grant agreement no. 731117), from the European Commission and the Spanish Ministry of Science, Innovation and Universities (PCI2018‐092933). F. Parisio acknowledges funding from the Deutsche Forschungsgemeinschaft (DFG, German Research Foundation)—project number PA 3451/1‐1. The authors thank Tomas Aquino for his advice on the integral solutions., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Unraveling the Causes of the Seismicity Induced by Underground Gas Storage at Castor, Spain

  • Vilarrasa, Víctor
  • De Simone, Silvia
  • Carrera, Jesús
  • Villaseñor, Antonio
10 pages, 4 figures, supporting information https://doi.org/10.1029/2020GL092038.-- Data Availability Statement: The associated data is available at the repository DIGITAL.CSIC (https://digital.csic.es/handle/10261/216863, The offshore Castor Underground Gas Storage (UGS) project had to be halted after gas injection triggered three M4 earthquakes, each larger than any ever induced by UGS. The mechanisms that induced seismicity in the crystalline basement at 5–10 km depth after gas injection at 1.7 km depth remain unknown. Here, we propose a combination of mechanisms to explain the observed seismicity. First, the critically stressed Amposta fault, bounding the storage formation, crept by the superposition of well‐known overpressure effects and buoyancy of the relatively light injected gas. This aseismic slip brought an unmapped critically stressed fault in the hydraulically disconnected crystalline basement to failure. We attribute the delay between induced earthquakes to the pressure drop associated to expansion of areas where earthquakes slips cause further instabilities. Earthquakes occur only after these pressure drops have dissipated. Understanding triggering mechanisms is key to forecast induced seismicity and successfully design deep underground operations., The authors would like to acknowledge Álvaro González for sharing the catalogs that were used in Cesca et al. (2014). Funding: Víctor Vilarrasa acknowledges funding from the European Research Council (ERC) under the European Union’s Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (www.georest.eu) (grant agreement No. 801809). Antonio Villaseñor acknowledges funding from Spanish Ministry of Science and Innovation grant CGL2017‐88864‐R. IDAEA‐CSIC is a Center of Excellence Severo Ochoa (Spanish Ministry of Science and Innovation, Project CEX2018‐000794‐S). ICM‐CSIC is a Center of Excellence Severo Ochoa (Spanish Ministry of Science and Innovation, Project CEX2019‐000928‐S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

How Equivalent Are Equivalent Porous Media?

  • Zareidarmiyan, Ahmad
  • Parisio, Francesco
  • Makhnenko, Roman Y.
  • Salarirad, Hossein
  • Vilarrasa, Víctor
Geoenergy and geoengineering applications usually involve fluid injection into and production from fractured media. Accounting for fractures is important because of the strong poromechanical coupling that ties pore pressure changes and deformation. A possible approach to the problem uses equivalent porous media to reduce the computational cost and model complexity instead of explicitly including fractures in the models. We investigate the validity of this simplification by comparing these two approaches. Simulation results show that pore pressure distribution significantly differs between the two approaches even when both are calibrated to predict identical values at the injection and production wells. Additionally, changes in fracture stability are not well captured with the equivalent porous medium. We conclude that explicitly accounting for fractures in numerical models may be necessary under some circumstances to perform reliable coupled thermohydromechanical simulations, which could be used in conjunction with other tools for induced seismicity forecasting., A.Z. acknowledges the financial support received from the “Iran's Ministry of Science, Research and Technology” (PhD students' sabbatical grants) for visiting IDAEA‐CSIC. The contribution of F.P. is funded by the Deutsche Forschungsgemeinschaft (DFG, German Research Foundation)—project number PA 3451/1‐1. R.M. is thankful for the support from US DOE through Carbon SAFE Macon County Project DE‐FE0029381. V.V. acknowledges funding from the Spanish National Research Council (CSIC) through the Intramural project 201730I100 and from the European Research Council (ERC) under the European Union's Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (www.georest.eu) (Grant agreement No. 801809). IDAEA‐CSIC is a Center of Excellence Severo Ochoa (Spanish Ministry of Science and Innovation, Project CEX2018‐000794‐S). The authors declare no conflict of interest., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Hubs and clusters approach to unlock the development of carbon capture and storage – Case study in Spain

  • Sun, Xiaolong
  • Alcalde, Juan
  • Elío, Javier
  • Bakhtbidar, Mahdi
  • Vilarrasa, Víctor
  • Canal, Jacobo
  • Ballesteros, Julio
  • Heinemann, Niklas
  • Haszeldine, Stuart
  • Cavanagh, Andrew
  • Vega-Maza, David
  • Rubiera González, Fernando
  • Martínez-Orio, Roberto
  • Johnson, Gareth
  • Carbonell, Ramón
  • Marzán, Ignacio
  • Travé, Anna
  • Gómez-Rivas, Enrique
Many countries have assigned an indispensable role for carbon capture and storage (CCS) in their national climate change mitigation pathways. However, CCS deployment has stalled in most countries with only limited commercial projects realised mainly in hydrocarbon-rich countries for enhanced oil recovery. If the Paris Agreement is to be met, then this progress must be replicated widely, including hydrocarbon-limited countries. In this study, we present a novel source-to-sink assessment methodology based on a hubs and clusters approach to identify favourable regions for CCS deployment and attract renewed public and political interest in viable deployment pathways. Here, we apply this methodology to Spain, where fifteen emission hubs from both the power and the hard-to-abate industrial sectors are identified as potential CO2 sources. A priority storage structure and two reserves for each hub are selected based on screening and ranking processes using a multi-criteria decision-making method. The priority source-to-sink clusters are identified indicating four potential development regions, with the North-Western and North-Eastern Spain recognised as priority regions due to resilience provided by different types of CO2 sources and geological structures. Up to 68.7 Mt CO2 per year, comprising around 21% of Spanish emissions can be connected to clusters linked to feasible storage. CCS, especially in the hard-to-abate sector, and in combination with other low-carbon energies (e.g., blue hydrogen and bioenergy), remains a significant and unavoidable contributor to the Paris Agreement’s mid-century net-zero target. This study shows that the hubs and clusters approach can facilitate CCS deployment in Spain and other hydrocarbon-limited countries., Funding was provided by the Grup Consolidat de Recerca “Geologia Sedimentària” (2017SGR-824) and the DGICYT Spanish Project PGC2018-093903-B-C22. XS acknowledges funding by the China Scholarship Council for a PhD scholarship (201806450043). JA is funded by MICINN (Juan de la Cierva fellowship - IJC2018-036074-I). EGR acknowledges funding provided by MICINN (“Ramón y Cajal” fellowship RYC2018-026335-I). VV acknowledges funding from the European Research Council (ERC) under the European Union’s Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (www.georest.eu) (Grant agreement No. 801809). IDAEA-CSIC is a Centre of Excellence Severo Ochoa (Spanish Ministry of Science and Innovation, Project CEX2018-000794-S). NH is funded by the Engineering and Physical Sciences Research Council (EPSRC) funded research project “HyStorPor” (EP/S027815/1). SH and AC are funded by EPSRC EP/P026214/1 UKCCSRC 2017, and EU project 837754 - STRATEGY CCUS. DVM is funded by the Spanish Ministry of Science, Innovation and Universities (“Beatriz Galindo Senior” fellowship BEAGAL18/00259). GJ is funded by the University of Strathclyde Faculty of Engineering., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Cooling-induced reactivation of distant faults during long-term geothermal energy production in hot sedimentary aquifers

  • Kivi, Iman Rahimzadeh
  • Pujades, Estanislao
  • Rutqvist, Jonny
  • Vilarrasa, Víctor
Deep geothermal energy (DGE) represents an opportunity for a sustainable and carbon-free energy supply. One of the main concerns of DGE is induced seismicity that may produce damaging earthquakes, challenging its widespread exploitation. It is widely believed that the seismicity risk can be controlled by using doublet systems circulating water to minimize the injection-induced pressure changes. However, cold water reinjection may also give rise to thermal stresses within and beyond the cooled region, whose potential impacts on fault reactivation are less well understood. Here, we investigate by coupled thermo-hydro-mechanical modeling the processes that may lead to fault reactivation in a hot sedimentary aquifer (HSA) in which water is circulated through a doublet. We show that thermal stresses are transmitted much ahead of the cooled region and are likely to destabilize faults located far away from the doublet. Meanwhile, the fault permeability mainly controls the fault reactivation timing, which entails the importance of employing appropriate characterization methods. This investigation is crucial for understanding the mechanisms controlling induced seismicity associated with DGE in a HSA and allows the success of future DGE projects., I.R.K. and V.V. acknowledge funding from the European Research Council (ERC) under the ‎European Union’s Horizon 2020 Research and Innovation Program through the Starting Grant ‎GEoREST (http://www.georest.eu) under Grant agreement No. 801809. I.R.K. also acknowledges support by the grant IJC2020-043809-I funded by MCIN/AEI/ 10.13039/501100011033 and the European Union NextGenerationEU/PRTR. IDAEA-CSIC is a Centre of Excellence Severo Ochoa (Spanish ‎Ministry of Science and Innovation, Grant CEX2018-000794-S funded by MCIN/AEI/ 10.13039/501100011033). Additional funding was provided to J.R. by the U.S. Department of Energy under contract No. DE-AC0205CH11231 to the Lawrence Berkeley National Laboratory and to E.P. through the grant RYC2020-029225-I funded by MCIN/AEI/ 10.13039/501100011033., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Two-Phase Flow Mechanisms Controlling CO2 Intrusion into Shaly Caprock

  • Kivi, Iman Rahimzadeh
  • Makhnenko, Roman Y.
  • Vilarrasa, Víctor
Geologic carbon storage in deep saline aquifers has emerged as a promising technique to mitigate climate change. CO2 is buoyant at the storage conditions and tends to float over the resident brine jeopardizing long-term containment goals. Therefore, the caprock sealing capacity is of great importance and requires detailed assessment. We perform supercritical CO2 injection experiments on shaly caprock samples (intact caprock and fault zone) under representative subsurface conditions. We numerically simulate the experiments, satisfactorily reproducing the observed evolution trends. Simulation results highlight the dynamics of CO2 flow through the specimens with implications to CO2 leakage risk assessment in field practices. The large injection-induced overpressure drives CO2 in free phase into the caprock specimens. However, the relative permeability increase following the drainage path is insufficient to provoke an effective advancement of the free-phase CO2. As a result, the bulk CO2 front becomes almost immobile. This implies that the caprock sealing capacity is unlikely to be compromised by a rapid capillary breakthrough and the injected CO2 does not penetrate deep into the caprock. In the long term, the intrinsically slow molecular diffusion appears to dominate the migration of CO2 dissolved into brine. Nonetheless, the inherently tortuous nature of shaly caprock further holds back the diffusive flow, favoring safe underground storage of CO2 over geological time scales., Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature. The research presented in this article was funded by the European Research Council (ERC) under the European Union’s Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (www.georest.eu) (Grant agreement No. 801809). This work was partly supported by the Spanish Ministry of Science and Innovation through the grant CEX2018-000794-S, funded by MCIN/AEI/10.13039/501100011033. Additional support was provided by the grant IJC2020-043809-I funded by MCIN/AEI/10.13039/501100011033 and the European Union NextGenerationEU/PRTR. This study also received the support from US DOE through CarbonSAFE Macon County Project DE-FE0029381. Open access funding provided by the Spanish National Research Council (CSIC)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Multiple induced seismicity mechanisms at Castor underground gas storage illustrate the need for thorough monitoring

  • Vilarrasa, Víctor
  • De Simone, Silvia
  • Carrera, Jesús
  • Villaseñor, Antonio
A recent publication by Cesca et al.1 reanalyzes and expands seismic data to identify hypocenters of observed seismicity induced by the Castor Underground Gas Storage (UGS) operations. Their results confirm those of previous studies2,3 that earthquakes occurred below the storage formation on a fault dipping opposite from the Amposta fault, which bounds the reservoir. However, two important sets of disagreements require revising the conclusions by Cesca et al.1: the depth of hypocenters and the processes leading to seismicity. Inaccurate estimates of hypocenters location and partial consideration of the physical mechanisms that induce seismicity may imply endangering future deep underground projects., V.V. acknowledges funding from the European Research Council (ERC) under the European Union’s Horizon 2020 Research and Innovation Programme through the Starting Grant GEoREST (www.georest.eu) under grant agreement No. 801809. A.V. acknowledges funding from Spanish Ministry of Science and Innovation grant CGL2017-88864-R. IDAEA-CSIC and ICM-CSIC are Centres of Excellence Severo Ochoa (Spanish Ministry of Science and Innovation Grants CEX2018-000794-S and CEX2019-000928-S, respectively, funded by MCIN/AEI/ 10.13039/501100011033), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Hydro-mechanical response of opalinus clay in the CO<inf>2</inf> long-term periodic injection experiment (CO<inf>2</inf>LPIE) at the Mont Terri rock laboratory

  • Sciandra, Dario
  • Kivi, Iman Rahimzadeh
  • Vilarrasa, Víctor
  • Makhnenko, Roman Y.
  • Rebscher, Dorothee
Abstract: Guaranteeing the sealing capacity of caprocks becomes paramount as CO2 storage scales up to the gigaton scale. A significant number of laboratory experiments have been performed with samples of intact rock, showing that low-permeability and high-entry pressure caprocks have excellent sealing capacities to contain CO2 deep underground. However, discontinuities, such as bedding planes, fractures and faults, affect the rock properties at the field scale, being at the same time challenging to monitor in industrial-scale applications. To bridge these two spatial scales, Underground Research Laboratories (URLs) provide a perfect setting to investigate the field-scale sealing capacity of caprocks under a well-monitored environment. In particular, the CO2 Long-term Periodic Injection Experiment (CO2LPIE) at the Mont Terri rock laboratory, Switzerland, aims at quantifying the advance of CO2 in Opalinus Clay, an anisotropic clay-rich rock with bedding planes dipping 45° at the experiment location. To assist in the design of CO2LPIE and have an initial estimate of the system response, we perform plane-strain coupled Hydro-Mechanical simulations using a linear transversely isotropic poroelastic model of periodic CO2 injection for 20 years. Simulation results show that pore pressure changes and the resulting stress variations are controlled by the anisotropic behavior of the material, producing a preferential advance along the bedding planes. CO2 cannot penetrate into Opalinus Clay due to the strong capillary effects in the nanoscale pores, but advances dissolved into the resident brine. We find that the pore pressure oscillations imposed at the injection well are attenuated within tens of cm, requiring a close location of the monitoring boreholes with respect to the injection interval to observe the periodic signal. Article highlights: Underground rock laboratory experiments permit examining the caprock sealing capacity at a representative scale for CO2 storage;We perform coupled transverse isotropic hydro-mechanical simulations to gain insight on the response of shaly rock to CO2 periodic injection;Simulation results assist in the design of the injection amplitude and period and monitoring of the long-term periodic CO2 injection experiment., D.S., I.R.K. and V.V. acknowledge funding from the European Research Council (ERC) under the European Union’s Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (www.georest.eu) under Grant agreement No. 801809. I.R.K. also acknowledges support by the PCI2021-122077-2B project (www.easygeocarbon.com) funded by MCIN/AEI/10.13039/501100011033 and the European Union NextGenerationEU/PRTR. IDAEA-CSIC is a Centre of Excellence Severo Ochoa (Spanish Ministry of Science and Innovation, Grant CEX2018-000794-S, funded by MCIN/AEI/10.13039/501100011033 ). The authors would like to thank swisstopo and the Mont Terri Consortium for their comprehensive information and very valuable discussions. R.Y.M. acknowledges the support from US DOE through Carbon SAFE Illinois Corridor Project DE-FE0031892., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Multi-Layered Systems for Permanent Geologic Storage of CO<inf>2</inf> at the Gigatonne Scale

  • Kivi, Iman Rahimzadeh
  • Makhnenko, Roman Y.
  • Oldenburg, C. M.
  • Rutqvist, Jonny
  • Vilarrasa, Víctor
The effectiveness of Carbon Capture and Storage (CCS) as an imperative decarbonization technology relies on the sealing capacity of a fine-grained caprock to permanently store CO2 deep underground. Uncertainties in assessing the caprock sealing capacity increase with the spatial and temporal scales and may delay CCS deployment at the gigatonne scale. We have developed a computationally efficient transport model to capture the dynamics of basin-wide upward CO2 migration in a multi-layered setting over geological time scales. We find that massive capillary breakthrough and viscous flow of CO2, even through pervasively fractured caprocks, are unlikely to occur and compromise the storage security. Potential leakage from the injection reservoir is hampered by repetitive layering of overlying caprocks. This finding agrees with geologic intuition and should be understandable by the public, contributing to the development of climate policies around this technology with increased confidence that CO2 will be indefinitely contained in the subsurface., I.R.K. and V.V. acknowledge funding from the European Research Council (ERC) under the European Union's Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (www.georest.eu) under Grant agreement No. 801809. I.R.K. also acknowledges support by the PCI2021-122077-2B project (www.easygeocarbon.com) funded by MCIN/AEI/10.13039/501100011033 and the European Union NextGenerationEU/PRTR. IDAEA-CSIC is a Centre of Excellence Severo Ochoa (Spanish Ministry of Science and Innovation, Grant CEX2018-000794-S funded by MCIN/AEI/10.13039/501100011033). R.Y.M. acknowledges the support from US DOE through Carbon SAFE Illinois Corridor Project DE-FE0031892. Additional funding for completing this manuscript was provided to C.M.O. and J.R. by the U.S. Department of Energy under contract No. DE-AC0205CH11231 to the Lawrence Berkeley National Laboratory., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Chemo-hydro-mechanical effects of CO2 injection on reservoir and seal rocks: A review on laboratory experiments

  • Vafaie, Atefeh
  • Cama, Jordi
  • Soler, Josep M.
  • Kivi, Iman Rahimzadeh
  • Vilarrasa, Víctor
Geological carbon storage is one of the technologies required to arrive at the ambitious yet realistic net-zero emission target and climate change neutrality. Injected CO2 in geological formations acidifies the resident brine, inducing chemical reactions with the minerals. Reactions may alter the hydraulic and mechanical properties of the rock and have an impact on reservoir and wellbore integrity, reservoir injectivity, long-term compaction and caprock sealing capacity. We provide a comprehensive review of chemo-hydro-mechanical (CHM) effects of CO2 on the reservoir and sealing rocks, either intact or fractured, which have been studied through laboratory experiments under no-flow and open-flow conditions, i.e., batch and flow-through experiments. The hydraulic and mechanical rock properties affected by geochemical processes comprise (a) physical properties influencing the flow and transport of solutes (pore size distribution, porosity, permeability and fracture aperture and roughness), (b) multi-phase flow properties (capillary entry pressure and relative permeability), (c) mechanical characteristics, including stiffness (i.e., elastic moduli for intact rocks and normal stiffness for fractures), strength (cohesion, friction angle and fracture toughness), and poroelastic response (Biot's coefficient), and (d) time-dependent behavior of the rock (compaction creep). The experiments alone cannot capture the complex dynamics of CO2 flow underground, but they provide critical insights into short-term alteration mechanisms of rock with implications to geologic CO2 storage. Studying naturally altered rocks, extending the experiments to tens-of-meters-scale underground rock laboratories, and bringing together experimental observations and numerical simulations are valuable for the advance in the understanding of CHM processes and upscaling them across space and time., This work has received funding from European Joint Programme on Radioactive Waste Management, EJP-EURAD of the the European Union's Horizon 2020 Research and Innovation Programme 2014–2018 under agreement No. 847593, specifically from the WP MAGIC. I.R.K. and V.V. acknowledge funding from the European Research Council (ERC) under the European Union's Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (www.georest.eu) (Grant agreement No. 801809). I.R.K. also acknowledges support by the PCI2021-122077-2 B project (www.easygeocarbon.com) funded by MCIN/AEI/10.13039/501100011033 and the European Union NextGenerationEU/PRTR. J.C. and J.M.S. also acknowledge funding from the Catalan Government through project 2017SGR1733. IDAEA-CSIC is a Centre of Excellence Severo Ochoa (Spanish Ministry of Science and Innovation, Project CEX2018-000794-S funded by MCIN/AEI/10.13039/501100011033). This research has been carried out within the framework of the activities of the Spanish Government through the “Maria de Maeztu Centre of Excellence” accreditation to IMEDEA (CSIC-UIB) (CEX2021-001198). Open access funding is provided by the Spanish National Research Council (CSIC). The authors acknowledge Dr. Nicolas Espinoza for providing source figures to prepare Fig. 9., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2018-000794-S)., With funding from the Spanish government through the "Unit of Excellence Maria de Maeztu" accreditation (CEX2021-001198-M)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Poroelastic stress relaxation, slip stress transfer and friction weakening controlled post-injection seismicity at the Basel Enhanced Geothermal System

  • Boyet, Auregan
  • De Simone, Silvia
  • Ge, Shemin
  • Vilarrasa, Víctor
Induced seismicity is a limiting factor for the development of Enhanced Geothermal Systems (EGS). Its causal mechanisms are not fully understood, especially those of post-injection seismicity. To better understand the mechanisms that induced seismicity in the controversial case of the Basel EGS (Switzerland), we perform coupled hydro-mechanical simulation of the plastic response of a discrete pre-existing fault network built on the basis of the monitored seismicity. Simulation results show that the faults located in the vicinity of the injection well fail during injection mainly triggered by pore pressure buildup. Poroelastic stressing, which may be stabilizing or destabilizing depending on the fault orientation, reaches further than pressure diffusion, having a greater effect on distant faults. After injection stops, poroelastic stress relaxation leads to the immediate rupture of previously stabilized faults. Shear-slip stress transfer, which also contributes to post-injection reactivation of distant faults, is enhanced in faults with slip-induced friction weakening., A.B. and V.V. acknowledge funding from the European Research Council (ERC) under the European Union’s Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (www.georest.eu) under Grant agreement No. 801809. IDAEA-CSIC is a Centre of Excellence Severo Ochoa (Spanish Ministry of Science and Innovation, Grant CEX2018-000794-S funded by MCIN/AEI/ https://doi.org/10.13039/501100011033). This research has been carried out within the framework of the activities of the Spanish Government through the “Maria de Maeztu Centre of Excellence” accreditation to IMEDEA (CSIC-UIB) (CEX2021-001198)., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2018-000794-S), With funding from the Spanish government through the ‘María de Maeztu Unit of Excelence’ accreditation (CEX2021-001198), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Physics‐Based Modeling to Understand and to Propose Forecasting Methods of Induced Seismicity

  • Boyet, Auregan
  • Vilarrasa, Víctor
  • De Simone, Silvia
Induced seismicity compromises the widespread deployment of geoenergy applications that contribute to mitigate climate change. In particular, the development of Enhanced Geothermal Systems (EGS) has been hindered by the risk of induced seismicity, mostly caused by hydraulic stimulation aimed at enhancing the permeability of deep hot crystalline rocks. Injection‐induced seismicity has been traditionally attributed to fluid pressure buildup, which destabilizes fractures and faults. However, the largest seismic events commonly occur after the stop of injection, when pore pressure drops and both the magnitude and frequency of induced seismicity is expected to decrease. This counterintuitive phenomenon is not well understood. Yet, understanding the triggering mechanisms is the key to reliably forecast and manage induced seismicity. Here, we investigate the triggering mechanisms of co‐ and post‐injection seismicity using coupled hydromechanical models, considering both a homogeneous and a fault‐crossed domain, based on the case of Basel EGS (Switzerland). We find that the combination of pressure diffusion, poroelastic stressing, and static stress transfer explains the occurrence of induced seismicity, especially after the stop of injection, significantly better than the pore pressure alone. Considering a fault zone, which is more permeable and deformable than the surrounding rock, amplifies pressure diffusion along the fault and causes anisotropic variations of the stress field that lead to an increase in the seismicity rate that is orders of magnitude larger than for the homogeneous domain. These results point out that identifying the main geological structures through subsurface characterization is key to improve physics‐based induced seismicity forecasting., A.B. and V.V. acknowledge funding from the European Research Council (ERC) under the European Union’s Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (www.georest.eu) under Grant agreement No. 801809. IDAEA-CSIC is a Centre of Excellence Severo Ochoa (Spanish Ministry of Science and Innovation, Grant CEX2018-000794-S funded by MCIN/AEI/ 10.13039/501100011033). IMEDEA is an accredited"Maria de Maeztu Excellence Unit" (Grant CEX2021-001198, funded by MCIN/AEI/10.13039/501100011033) S.D.S. acknowledges the support of the European Union “Next Generation EU”/PRTR and the Spanish Ministry of Science and Innovation through the ‘Ramón y Cajal’ fellowship (reference RYC2021-032780-I)., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2018-000794-S)., With funding from the Spanish government through the "Unit of Excellence Maria de Maeztu" accreditation (CEX2021-001198-M)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Global physics-based database of injection-induced seismicity

  • Kivi, Iman Rahimzadeh
  • Boyet, Auregan
  • Wu, Haiqing
  • Walter, Linus
  • Hanson-Hedgecock, Sara
  • Parisio, Francesco
  • Vilarrasa, Víctor
Fluid injection into geological formations for energy resource development frequently induces (micro)seismicity. Moderate- to large-magnitude induced earthquakes may cause injuries and/or economic loss, with the consequence of jeopardizing the operation and future development of these geo-energy projects. To achieve an improved understanding of the mechanisms of induced seismicity, develop forecasting tools and manage the associated risks, it is necessary to carefully examine seismic data from reported cases of induced seismicity and the parameters controlling them. However, these data are challenging to gather together and are time-consuming to collate as they come from different disciplines and sources. Here, we present a publicly available, multi-physical database of injection-induced seismicity (Kivi et al., 2022a; 10.20350/digitalCSIC/14813), sourced from an extensive review of published documents. Currently, it contains 158 datasets of induced seismicity caused by various subsurface energy-related applications worldwide. Each dataset covers a wide range of variables, delineating general site information, host rock properties, in situ geologic and tectonic conditions, fault characteristics, conducted field operations, and recorded seismic activities. We publish the database in flat-file formats (i.e., .xls and .csv tables) to facilitate its dissemination and utilization by geoscientists while keeping it directly readable by computer codes for convenient data manipulation. The multi-disciplinary content of this database adds unique value to databases focusing only on seismicity data. In particular, the collected data aim at facilitating the understanding of the spatiotemporal occurrence of induced earthquakes, the diagnosis of potential triggering mechanisms, and the development of scaling relations of maximum possible earthquake magnitudes and operational parameters. The database will boost research in seismic hazard forecasting and mitigation, paving the way for increasing contributions of geo-energy resources to meeting net-zero carbon emissions., The authors acknowledge funding from the European Research Council (ERC) under the European Union's Horizon 2020 Research and Innovation Program through the starting grant GEoREST (http://www.georest.eu, last access: 23 July 2023) under grant agreement no. 801809. Iman R. Kivi and Victor Vilarrasa also acknowledge support by the PCI2021-122077-2B project (http://www.easygeocarbon.com, last access: 23 July 2023), funded by MCIN/AEI/10.13039/501100011033 and the European Union NextGenerationEU/PRTR. Haiqing Wu acknowledges the financial support received from the Secretariat for Universities and Research of the Ministry of Business and Knowledge of the Government of Catalonia (AGAUR) and the European Social Fund (FI-2019). Haiqing Wu also acknowledges the Becas Santander Research Scholarship from the Technical University of Catalonia (UPC) and Santander. Francesco Parisio and Victor Vilarrasa acknowledge funding from the European Union's Horizon 2020 Research and Innovation Programme through the Marie Skłodowska-Curie Action ARMISTICE under grant agreement no. 882733. IDAEA-CSIC is a Centre of Excellence Servero Ochoa (Spanish Ministry of Science and Innovation, grant no. CEX2018-000794-S, funded by MCIN/AEI/10.13039/501100011033). IMEDEA is an accredited “Maria de Maeztu Excellence Unit” (grant no. CEX2021-001198, funded by MCIN/AEI/10.13039/501100011033)., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2018-000794-S)., With funding from the Spanish government through the "Unit of Excellence Maria de Maeztu" accreditation (CEX2021-001198-M)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Chemo-hydro-mechanical effects of CO<inf>2</inf> injection into a permeable limestone

  • Vafaie, Atefeh
  • Cama, Jordi
  • Soler, Josep M.
  • Grgic, D.
  • Vilarrasa, Víctor
CO2 storage in carbonate aquifers is a way to mitigate atmospheric CO2 emissions, but it leads to acid-producing reactions that may induce alterations in the rock pore structure and hydromechanical properties. To gain a better understanding of these changes in rock properties, percolation experiments under constant flow-rate conditions with (i) CO2-saturated water (PCO2 = 100 bar and T = 60 °C) and (ii) HCl solutions (P = 1 bar and T = 60 °C) were performed on centimetric cores of the grain-supported Pont du Gard Limestone (permeability about 10−14–10−13 m2). Effluent chemistry analyses, X-ray imaging, and measurements of the hydromechanical properties of intact and altered specimens were used to quantify acid-induced changes in the two acid-rock systems. Experimental results show that the rock dissolution patterns highly depend on the acid type and pore space heterogeneity. Under the flow conditions of these experiments, complete HCl dissociation (strong acid) and rapid HCl-rock reaction result in a compact dissolution pattern that only affects the hydromechanical properties of the core inlet. Conversely, partial dissociation of H2CO3 (weak acid) produces chemical reactions all along the core. Initial structural heterogeneities localize chemical reactions along preferential flow pathways, causing instabilities in the reaction front and wormhole formation, which markedly enhances permeability. A powerlaw relationship with a very large exponent (as high as 24) accounts for the variation in permeability as a function of porosity. Altered cores render both a significant attenuation in mechanical rock properties and ultrasonic velocities, which is reproduced using a Differential Effective Medium (DEM) homogenization approach. The high-pressure percolation experiments of this study using CO2-saturated water represent an extreme scenario of CO2-brine-rock interactions in carbonate reservoirs, which needs to be considered to improve the prediction and monitoring of the storage performance., This work has received funding from the European Union's Horizon 2020 Research and Innovation Programme 2014-2018 under agreement No. 847593, specifically from the WP MAGIC. A.V. acknowledges funding from the University of Barcelona under Travel grants for Ph.D. students in Earth Sciences 2020. V.V. acknowledges funding from the European Research Council (ERC) under the European Union's Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (www.georest.eu) (Grant agreement No. 801809). J.C. and J.M.S. also acknowledge funding from the Catalan Government through project 2017SGR1733. IDAEA-CSIC is a Centre of Excellence Severo Ochoa (Spanish Ministry of Science and Innovation, Project CEX2018-000794-S funded by MCIN/AEI/10.13039/501100011033). IMEDEA is an accredited “Maria de Maeztu Excellence Unit” (Grant CEX2021-001198, funded by MCIN/AEI/10.13039/501100011033). Thanks are due to Jordi Bellés (IDAEA-CSIC), Laurent Schoumacker (GeoResources Laboratory) and Christophe Morlot (GeoResources Laboratory) for their help in conducting the percolation experiments, MICP and uniaxial compression tests, and XMCT imaging, respectively. The authors would also like to thank the thoughtful reviews by anonymous reviewers, which helped improve the quality of the article., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2018-000794-S)., With funding from the Spanish government through the "Unit of Excellence Maria de Maeztu" accreditation (CEX2021-001198-M)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Reservoir impoundment-triggered seismicity in Brazil: the case of M4.0 Nova Ponte earthquake

  • Raza, Haris
  • Kivi, Iman Rahimzadeh
  • França, George Sand
  • Vilarrasa, Víctor
Reservoir-triggered seismicity commonly occurs as a result of reservoir impoundment. In particular, the Nova Ponte reservoir triggered a series of earthquakes, including the 1998 M4.0 earthquake, which represents the second-largest earthquake triggered by reservoir impoundment in Brazil. The earthquake occurred after prolonged seismic activity following reservoir impoundment starting in 1993. After more than two decades, the mechanisms governing these earthquakes and their relation with the spatiotemporal evolution of the seismic events are still poorly understood. Here, we explain the causal mechanisms of the two largest earthquakes: an initial response M3.5 in 1995 and the delayed M4.0 in 1998. To this end, we numerically simulate the poromechanical subsurface response to reservoir impoundment using a 3D model that includes three geological layers down to 10 km depth. From the proposed potential nodal planes of the 1995 M3.5 earthquake, we show that the earthquake has most likely occurred on a vertical, E-W-oriented strike-slip fault with a reverse-displacement component. Deviatoric stresses generated by the water column loading on the surface, superimposed by undrained pore pressure enhancement in deep low-permeability layers can explain the fault reactivation. We find that for the 1998 M4.0 earthquake to occur, conductive flow pathways with permeability as high as 6.6·10-15 m2 should exist to transmit pore pressure to a deep critically oriented fault. Our analysis raises the importance of accounting for coupled poromechanical mechanisms controlling fault stability, hydromechanical properties of different rock layers, and realistic shape of the reservoir to accurately assess the potential for reservoir-triggered seismicity. We conclude that reliable forecasting models require accurate subsurface characterization before reservoir filling to enable managing the associated reservoir-triggered seismicity., This study was financed in part by the Coordenação de Aperfeiçoamento de Pessoal de Nível Superior -Brasil (CAPES) -Finance Code 001. The authors acknowledge funding from the Spanish National Research Council (CSIC) under the Program for Scientific Cooperation iCOOP+ through the Project COOPA20414. IDAEA-CSIC is a Centre of Excellence Severo Ochoa (Spanish Ministry of Science and Innovation, Grant CEX2018-000794-S, funded by MCIN/AEI/10.13039/501100011033). IMEDEA is an accredited "Maria de Maeztu Excellence Unit" (Grant CEX2021-001198, funded by MCIN/AEI/10.13039/501100011033). G.S.F. thanks to CNPq grants 310240/2020-4. The authors also thanks to INCTET-CNPq (Institutos Nacionais de Ciência e Tecnología de estudos tectônicos) Brazil. I.R.K. and V.V. acknowledges support by the PCI2021-122077-2B project (www.easygeocarbon.com) funded by MCIN/AEI/10.13039/501100011033 and the European Union Next Generation EU/PRTR. V.V. acknowledges funding from the European Research Council (ERC) under the European Union’s Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (www.georest.eu) under Grant agreement No. 801809. I.R.K. also acknowledges funding from the Engineering and Physical Sciences Research Council through the UKRI Postdoc Guarantee THMC4CCS [Grant number EP/X026019/1]., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Analytical solution to quickly assess ground displacement for a pressurized or depleted deep reservoir intersected by a fault in a half space

  • Wu, Haiqing
  • Rutqvist, Jonny
  • Vilarrasa, Víctor
Quick estimates of fluid-induced subsurface deformation are helpful to assess the land uplift/subsidence and to reveal precursors of induced seismicity. Here, we adopt the inclusion theory and Green's function to develop a closed-form solution in a half space for the poroelastic response of a reservoir compartmentalized by an intersecting fault that can be offset and either permeable or impermeable. Simulated results reveal that (1) fault permeability mainly impacts the spatial distribution of displacement while its effect on displacement magnitude is small; (2) ground displacement slightly increases with fault dip while slightly decreases with increasing fault offset; in contrast, reservoir geometry shows a stronger effect than fault geometry: the ground displacement is proportional to the vertical and lateral depth ratios, defined as the ratios of reservoir thickness (h) and width (w) to reservoir depth (D), respectively; (3) the maximum vertical displacement is the double of the horizontal one regardless of fault permeability, fault and reservoir geometries, and mechanical parameters. Comparing the solution in a half space with that in a full space shows that neglecting the free surface underestimates the poroelastic displacement in the overburden. The validity of full-space solutions can be assessed with the product of the lateral and vertical depth ratios, i.e., wh/D2. The full-space solutions become valid when wh/D2 decreases to an intrinsic threshold. This threshold may range from 0.01 to 0.02 for displacement, and its specific value depends on the field background and demands of projects, but can be estimated based on our solution. It is larger for stress than for displacement, and wh/D2 ≤ 0.1 is recommended as a general condition for neglecting the free-surface effects on induced stress. The analytical solution represents a useful tool for estimating ground deformation and for gaining insights of reservoir and fault geometries by analyzing surface deformation patterns., H.W. would like to acknowledge the financial support received from the Secretariat for Universities and Research of the Ministry of Business and Knowledge of the Government of Catalonia (AGAUR) and the European Social Fund (FI-2019). H.W. also acknowledges the Becas Santander Research Scholarship from the Technical University of Catalonia (UPC) and the Santander. J.R. acknowledges funding by the Assistant Secretary for Fossil Energy, National Energy Technology Laboratory, National Risk Assessment Partnership of the U.S. Department of Energy to the Lawrence Berkeley National Laboratory under contract no. DEAC02-05CH11231. V.V. acknowledges funding from the European Research Council (ERC) under the European Union's Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (www.georest.eu) under Grant agreement No. 801809. IMEDEA is an accredited “Maria de Maeztu Excellence Unit” (Grant CEX2021-001198, funded by MCIN/AEI/10.13039/501100011033)., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2021-001198)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

On the role of poroelastic stressing and pore pressure diffusion in discrete fracture and fault system in triggering post-injection seismicity in enhanced geothermal systems

  • Kivi, Iman Rahimzadeh
  • Vilarrasa, Víctor
  • Kim, Kwang Il
  • Yoo, Hwajung
  • Min, Ki-Bok
© 2024 The Authors. Published by Elsevier Ltd. This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0/)., Injection-induced seismicity has become one of the most critical challenges for the widespread deployment of Enhanced Geothermal Systems (EGS). In particular, some EGS development projects have led to large, damaging earthquakes that unexpectedly occurred far off the stimulated reservoir region and, in particular, after stopping fluid injection. Yet, the causative mechanisms of these seismicity patterns remain highly elusive. Here, we identify a combination of mechanisms that could explain delayed seismicity in EGS sites by conducting fully-coupled hydromechanical simulations of the hydraulic stimulation of a naturally-fractured granitic reservoir. The model comprises a sparse network of long, variably-oriented fractures interacting with a nearby, critically-oriented fault. The results show that the presence of fractures introduces notable nonlinearities in the flow field and rock deformation and significantly expands the rock volume affected by fluid injection. First, the stimulated fracture network provides highly-permeable conduits for communicating elevated pore pressure over long distances. Second, the anisotropic expansion of fractures generates shear stress that is transmitted almost instantaneously across the reservoir. The pore pressure and stress perturbations can not only cause slip along fractures, inducing (micro)seismicity during injection, but also affect the stability of nearby faults, which may not necessarily be pressurized during injection. The transferred poroelastic stresses can increase or decrease the slip tendency along different fault segments. However, the fault may reactivate only after several months following injection when a progressive pore pressure diffusion modulated by the transient fault permeability evolution brings a critically-stressed fault segment to failure conditions. We also find that the spatiotemporal evolution of seismicity depends largely on the nearby fault orientation, hydromechanical properties, and hydraulic connection with the fracture network, as well as the initial state of stress. We conclude that accurate subsurface characterization and continuous monitoring during and after injection should allow for managing the risks posed by injection-induced seismicity and safely unlocking the immense potential for clean and sustainable geothermal energy., I.R.K. and V.V. acknowledge support by the PCI2021-122077-2B project (http://www.easygeocarbon.com) funded by MCIN/AEI/10.13039/501100011033 and the European Union NextGenerationEU/PRTR. I.R.K. also acknowledges funding from the Engineering and Physical Sciences Research Council through the UKRI Postdoc Guarantee Award THMC4CCS [Grant number EP/X026019/1]. V.V. also acknowledges funding from the European Research Council (ERC) under the European Union's Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (http://www.georest.eu) under Grant agreement No. 801809. IDAEA-CSIC is a Centre of Excellence Severo Ochoa (Spanish Ministry of Science and Innovation, Grant CEX2018-000794-S funded by MCIN/AEI/10.13039/501100011033). IMEDEA is an accredited "Maria de Maeztu Excellence Unit" (Grant CEX2021-001198, funded by MCIN/AEI/10.13039/501100011033). K.I.K. acknowledges support by the Innovative Technology Development Program for High-level waste management of the National Research Foundation of Korea (NRF) funded by the Korea government (Ministry of Science and ICT, MSIT) (Grant No.2021M2E3A2041312). K.-B.M. and H.Y. were supported by a grant from the Human Resources Development program (No. 20204010600250) of the Korea Institute of Energy Technology Evaluation and Planning (KETEP), funded by the Ministry of Trade, Industry, and Energy of the Korean Government. K.-B.M. and H.Y. were also supported by the Innovative Technology Development Program for High-level waste management of the National Research Foundation of Korea (NRF) funded by the Korea government (Ministry of Science and ICT, MSIT) (Grant No. 2021M2E3A2044264)., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2018-000794-S)., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2021-001198-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Numerical modeling of hydraulic stimulation of fractured crystalline rock at the bedretto underground laboratory for geosciences and geoenergies

  • Vaezi, Iman
  • Alcolea, Andrés
  • Meier, Peter
  • Parisio, Francesco
  • Carrera, Jesús
  • Vilarrasa, Víctor
© 2024 The Authors. Published by Elsevier Ltd. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/)., Hydraulic stimulation of Enhanced Geothermal Systems (EGS) aims at boosting permeability to facilitate fluid circulation, while keeping a low induced seismicity. However, some stimulations have led to poor permeability enhancement or too high induced earthquakes, which suggests that further understanding is needed on poromechanical processes during stimulation. Here, we model a highly-monitored test performed at the Bedretto Underground Laboratory to investigate the impact of fluid injection on permeability enhancement and induced microseismicity. We examine three models: (1) a homogeneous fracture whose transmissivity is manually calibrated to reproduce the observed pressure evolution at the injection borehole (this model fails to capture the spatial distribution of pressure and the corresponding poromechanical processes); (2) an elastic fracture approach, where transmissivity changes locally as a function of fracture aperture following the cubic law (this model overestimates pressure after the onset of fracture slip); and (3) a viscoplastic fracture approach with strain weakening and dilatancy that yields an additional permeability enhancement after shear reactivation. The viscoplastic model captures the spatio-temporal coupled response of the fractured rock to hydraulic stimulation before and after shearing both in terms of pressure and microseismicity. Subsequently to the onset of shear failure, microseismic events occur in every injection cycle as the reactivation front advances when plastic strain and, thus, permeability surpass the previously achieved maximum value. This viscoplastic model permits estimating the extent of the stimulated fracture, the permeability enhancement and its impact on the local state of stress and pore pressure at surrounding fractures, representing a useful tool for the design of effective hydraulic stimulation., I.V. and V.V. acknowledge funding from the European Research Council (ERC) under the European Union's Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (www.georest.eu), under grant agreement No. 801809. The work of Geo-Energie Suisse AG was financially supported by the Swiss Federal Office of Energy within the framework of the ZoDrEx GEOTHERMICA project under contract SI/501720-01. F.P. and V.V. acknowledge funding from the European Union’s Horizon 2020 Research and Innovation Program through the Marie Sklowdowska-Curie Individual Fellowship ARMISTICE, under Grant Agreement No. 882733. J.C. and V.V. acknowledges financial support from the “ZoDrEx” project, which has been subsidized through the ERANET Cofund GEOTHERMICA (Project No. 731117), from the European Commission and the Spanish Ministry of Economy, Industry and Competitiveness (MINECO). IMEDEA is an accredited "Maria de Maeztu Excellence Unit" (Grant CEX2021-001198, funded by MCIN/AEI/10.13039/501100011033). IDAEA-CSIC is a Center of Excellence Severo Ochoa (Spanish Ministry of Science and Innovation, Project CEX2018-000794-S)., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2021-001198)., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2018-000794-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Hydromechanical modeling of the hydraulic stimulations in borehole PX2 (Pohang, South Korea)

  • Alcolea, Andrés
  • Meier, Peter
  • Vilarrasa, Víctor
  • Olivella, Sebastià
  • Carrera, Jesús
A Mw 5.5 earthquake struck Pohang (South Korea) on November 2017, following a sequence of five hydraulic stimulations of an Enhanced Geothermal System (EGS). The processes that led to this earthquake, which nucleated two months after the end of the last stimulation in borehole PX2, are not well understood yet. We propose a hydromechanical model that integrates available data to understand the potential relationship between the earthquake and the EGS. Data scarcity is translated into model uncertainties, which we address with sensitivity analyses. Results show that the Mw 5.5 earthquake is linked to the high-injection overpressures of up to 90 MPa induced during the stimulations in borehole PX2 and highlight the usefulness of hydromechanical modeling to forecast the seismicity of an EGS and, more specifically, the need to integrate the low permeability fault core that hindered fluid pressure dissipation at Pohang, which explains the long delay of the mainshock., The work of Andrés Alcolea and Peter Meier was supported by the European Union Horizon 2020 research and innovation programme under grant agreement number 691728, and by the Swiss State Secretariat for Education, Research and Innovation (SERI) under contract number 15-0316-1. The opinions expressed and arguments employed herein do not necessarily reflect the official views of the Swiss Government. Víctor Vilarrasa acknowledges funding from the European Research Council (ERC) under the European Union's Horizon 2020 Research and Innovation Programme through the Starting Grant GEoREST (www.georest.eu) under grant agreement no. 801809. IDAEA-CSIC is a Centre of Excellence Severo Ochoa (Spanish Ministry of Science and Innovation, grant CEX2018-000794-S funded by MICIU/AEI/10.13039/501100011033). IMEDEA is an accredited "Maria de Maeztu Excellence Unit" (grant CEX2021-001198, funded by MICIU/AEI/10.13039/501100011033)., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2018-000794-S)., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2021-001198)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effectiveness of injection protocols for hydraulic stimulation in enhanced geothermal systems

  • Tangirala, Sri Kalyan
  • Parisio, Francesco
  • Vaezi, Iman
  • Vilarrasa, Víctor
© 2024 The Author(s). Published by Elsevier Ltd. This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0/)., To harness the immense potential of geothermal energy for non-intermittent baseload power, low-permeability crystalline hot rocks need to be hydraulically stimulated to create Enhanced Geothermal Systems (EGS) that enable economically profitable fluid flow rates. However, hydraulic stimulation is usually associated with seismic activity that has led to project cancellation in a few occasions. To improve our understanding of the coupled hydro-mechanical (HM) processes behind stimulation during both injection and post-injection stages (after shut-in), we numerically analyze three different stimulation protocols: constant-rate, step-rate, and cyclic injection with and without bleed-off after shut-in (and between cycles for the cyclic protocol). Simulation results show that the injection protocol has a higher influence on the HM response of the fracture than the total volume of injected water, which challenge scaling laws that relate the injection volume with the expected maximum magnitude of the induced earthquakes. The trade-off between maximizing permeability enhancement, while minimizing induced seismicity is not straightforward. In particular, bleeding-off the well after injection restricts induced seismicity, but at the expenses of limiting permeability enhancement. When considering stimulation of a single fault, all protocols yield comparable slip rates and, thus, magnitude of the induced earthquake, with the constant-rate injection being the fastest to induce the largest earthquake. The small differences in the HM response to hydraulic stimulation do not permit identifying a protocol that performs better than the others., European Research Council (ERC) under the European Union's Horizon 2020 Research and Innovation Program, grant agreement no. 801809. Marie Sklodowska-Curie Action Individual Fellowship, grant agreement no. 882733. Maria de Maeztu Excellence Unit (CEX2021-001198/AEI/10.13039/501100011033)., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2021-001198)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Forecasting fluid-injection induced seismicity to choose the best injection strategy for safety and efficiency

  • Boyet, Auregan
  • Vilarrasa, Víctor
  • Rutqvist, Jonny
  • De Simone, Silvia
Induced seismicity poses a challenge to the development of Enhanced Geothermal Systems (EGS). Improving monitoring and forecasting techniques is essential to mitigate induced seismicity and thereby fostering a positive perception of EGS projects among local authorities and population. Induced seismicity is the result of complex and coupled thermo-hydro-mechanical-chemical mechanisms. Injection flux and pressure are crucial controlling parameters for both hydraulic stimulation and circulation protocols. We develop a methodology combining a hydro-mechanical model with a seismicity rate model to estimate the magnitude and frequency of mainshocks and aftershocks induced by fluid injection. We apply the methodology to the case of the Basel EGS (2006, Switzerland) to compare the effects of progressive, cyclic and constant injections on the mechanical response of discrete faults. Results from the coupled hydro-mechanical models show that the pore pressure diffusion and consequent enhancement of fault permeability are limited to the vicinity of the injection well during cyclic injection. Additionally, constant injection induces seismicity from the start of the injection but enhances the permeability of most of the faults within a shorter duration, inducing less post-injection seismicity. The methodology can be adapted to any numerical model and allows new projects to be developed by anticipating the safest injection protocol.This article is part of the theme issue 'Induced seismicity in coupled subsurface systems'., A.B. and V.V. acknowledge funding from the European Research Council (ERC) under the European Union’s Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (www.georest.eu) under grant agreement no. 801809. IDAEA-CSIC is a Centre of Excellence Severo Ochoa (Spanish Ministry of Science and Innovation, grant CEX2018-000794-S funded by MICIU/AEI/ 10.13039/501100011033). IMEDEA is an accredited ‘Maria de Maeztu Excellence Unit’ (grant CEX2021-001198, funded by MICIU/AEI/10.13039/501100011033). S.D.S. acknowledges the support of the MICIU /AEI /10.13039/501100011033 and the European Union “Next Generation EU”//PRTR and the Spanish Ministry of Science and Innovation” through the ‘Ramón y Cajal’ fellowshipgrant (reference RYC2021-032780-I). Additional funding was provided to J.R. by the U.S. Department of Energy under contract No. DE-AC0205CH11231 to the Lawrence Berkeley National Laboratory., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Implicit hydromechanical representation of fractures using a continuum approach

  • Vaezi, Iman
  • Parisio, Francesco
  • Yoshioka, Keita
  • Alcolea, Andrés
  • Meier, Peter
  • Carrera, Jesús
  • Olivella, Sebastià
  • Vilarrasa, Víctor
Fractures control fluid flow, solute transport, and mechanical deformation in crystalline media. They can be modeled numerically either explicitly or implicitly via an equivalent continuum. The implicit framework implies lower computational cost and complexity. However, upscaling heterogeneous fracture properties for its implicit representation as an equivalent fracture layer remains an open question. In this study, we propose an approach, the Equivalent Fracture Layer (EFL), for the implicit representation of fractures surrounded by low-permeability rock matrix to accurately simulate hydromechanical coupled processes. The approach assimilates fractures as equivalent continua with a manageable scale (≫1 μm) that facilitates spatial discretization, even for large-scale models including multiple fractures. Simulation results demonstrate that a relatively thick equivalent continuum layer (in the order of cm) can represent a fracture (with aperture in the order of μm) and accurately reproduce the hydromechanical behavior (i.e., fluid flow and deformation/stress behavior). There is an upper bound restriction due to the Young's modulus because the equivalent fracture layer should have a lower Young's modulus than that of the surrounding matrix. To validate the approach, we model a hydraulic stimulation carried out at the Bedretto Underground Laboratory for Geosciences and Geoenergies in Switzerland by comparing numerical results against measured data. The method further improves the ability and simplicity of continuum methods to represent fractures in fractured media., I.V. and V.V. acknowledge funding from the European Research Council (ERC) under the European Union's Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST ( www.georest.eu ), under grant agreement No. 801809. J.C. and V.V. acknowledge financial support from the “ZoDrEx” project, which has been subsidized through the ERANET Cofund GEOTHERMICA (Project no. 731117), from the European Commission and the Spanish Ministry of Economy, Industry and Competitiveness (MINECO). The work of Geo-Energie Suisse AG was financially supported by the Swiss Federal Office of Energy within the framework of the ZoDrEx GEOTHERMICA project under contract SI/501720-01. F. P. acknowledges funding from the European Union's Horizon 2020 Research and Innovation Program through the Marie Sklowdowska-Curie Individual Fellowship ARMISTICE, Spain under Grant Agreement No. 882733. K.Y. acknowledges funding from EURAD, the European Joint Programme on Radioactive Waste Management through the project DONUT (Grant No 847593 ). IMEDEA is an accredited "Maria de Maeztu Excellence Unit" (Grant CEX2021-001198 , funded by MCIN/AEI/10.13039/501100011033). IDAEA-CSIC is a Center of Excellence Severo Ochoa (Spanish Ministry of Science and Innovation, Project CEX2018-000794-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Earthquakes triggered by the subsurface undrained response to reservoir impoundment at Irapé, Brazil

  • Raza, Haris
  • França, George Sand
  • Sayão, Eveline
  • Vilarrasa, Víctor
The necessity to reduce carbon emissions to mitigate climate change is accelerating the transition from fossil fuels to renewable energy sources. Specifically, hydropower has emerged as a prominent and safe renewable energy source but entails reservoir-triggered seismicity (RTS). This phenomenon causes significant challenges for safe reservoir management. Irapé, in Brazil, is a prominent RTS site where seismicity surged after reservoir filling, with a maximum event of magnitude 3.0 in May 2006, just 6 months after the start of reservoir impoundment. Despite the fact that more than 1 decade has passed since the seismicity occurred, the factors governing these earthquakes and their connection to subsurface rock properties remain poorly understood. Here, we attempt to understand the potential causes of RTS at Irapé Dam, which is the highest dam in Brazil at 208 m and the second highest in South America. Permeability and porosity measurements of cylindrical cores from hard and intact rock samples, which were extracted near the RTS zone by pitting 10 cm from the surface, reveal a low-permeability rock. Porosity values range from 6.3 % to 14.7 %. Only 3 out of the 11 tested samples present permeability above the lowest measurable value of the apparatus (0.002 mD), with the highest permeability being 0.0098 mD. The undrained response of the low-permeability rock placed below the reservoir results in an instantaneous increase in pore pressure and poroelastic stress changes due to elastic compression, which brings potential faults located below the reservoir closer to failure conditions. According to our analytical calculations, the vertical loading caused by the increase of 136 m in the reservoir water level led to a 0.61 MPa pore pressure buildup in response to compression at the depth of the Mw 3.0 earthquake, i.e., 3.88 km, resulting in an increase of 0.75 MPa in the vertical effective stress and of 0.48 MPa in the horizontal effective stress. These changes resulted in an increase in the deviatoric stress that led to fault destabilization, causing the RTS. The laboratory measurements and analytical calculations corroborate the hypothesis that the initial seismic activity was induced by the undrained subsurface response to the reservoir loading at Irapé., This study was financed in part by the Coordenação de Aperfeiçoamento de Pessoal de Nível Superior -Brasil (CAPES)-Finance Code 001. The authors acknowledge funding from the Spanish National Research Council (CSIC) under the Program for Scientific Cooperation iCOOP+ through the Project COOPA20414. Victor Vilarrasa acknowledges funding from the European Research Council (ERC) under the European Union's Horizon 2020 research and innovation program through the Starting Grant GEoREST (https://www.georest.eu/, last access: 17 November 2024) under grant no. 801809. IMEDEA is an accredited “Maria de Maeztu excellence Unit” (grant no. CEX2021-001198, funded by MICIU/AEI/10.13039/501100011033). George Sand França gratefully acknowledges CNPq (grant no. 310240/2020-4 PQ-1C). George Sand França, Haris Raza, and Eveline Sayão also thank the INCTET-CNPq (Institutos Nacionais de Ciência e Tecnología de estudos tectónicos) Brazil. We thank Prof. Carlos Jorge de Abreu for conducting samples measurements at the Laboratory of Physical Properties of Rocks at the University of Brasília., The article processing charges for this open-access publication were covered by the CSIC Open Access Publication Support Initiative through its Unit of Information Resources for Research (URICI)., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2021-001198)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Bleed-off control on post-injection seismicity in enhanced geothermal systems

  • Kivi, Iman Rahimzadeh
  • Vilarrasa, Víctor
  • Kim, Kwang Il
  • Yoo, Hwajung
  • Min, Ki-Bok
Deep geothermal reservoirs could provide widespread access to clean and renewable energy around the world. However, hydraulic stimulation of these reservoirs to create sufficient injectivity and heat extraction has frequently induced earthquakes during and, in particular, after reservoir stimulation, which raises public concerns. This study aims to provide a possible explanation for post-injection seismicity and understand how it responds to well bleed-off as a common industrial practice to control such seismic activity. To this end, we perform coupled hydromechanical simulations of reservoir stimulation in a conceptual model comprising a deep granitic reservoir intersected by a network of long fractures and a nearby, critically-stressed fault. We find a combination of mechanisms triggering post-injection seismicity with time delays of several months after stopping injection: (1) poroelastic stressing that transmits normal and shear stress and causes undrained pressure buildup on the fault, (2) fracture-dominated pore pressure migration toward the fault, and (3) long-lasting along-the-fault pressure diffusion toward pre-stressed fault patches, promoted by dilation-induced fault permeability changes. In this setting, bleed-off causes rapid pressure decline in the near-wellbore region but marginal pressure changes farther away. The resulting attenuations of pore pressure and shear stress on the fault plane may not be enough to prevent fault reactivation. Bleed-off may counterintuitively accelerate fault slip by rapid relaxation of normal stress on the fault, which not only brings the stress state closer to failure conditions, but also accelerates pore pressure diffusion along the fault by slightly increasing its permeability. We show that bleed-off can effectively control post-injection seismicity only if rupture initiates from a structure in close proximity and with sufficient hydraulic connection to the wellbore. Future research should be directed toward the optimization of stimulation and post-stimulation design in light of the involved triggering mechanisms and through effective combination with subsurface characterization to control post-injection seismicity., I.R.K. and V.V. acknowledge support by the PCI2021-122077-2B project (www.easygeocarbon.com) funded by MCIN/AEI/10.13039/501100011033 and the European Union NextGenerationEU/PRTR. I.R.K. also acknowledges funding from the Engineering and Physical Sciences Research Council through the UKRI Postdoc Guarantee Award THMC4CCS [Grant No. EP/X026019/1]. V.V. also acknowledges funding from the European Research Council under the European Union’s Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (www.georest.eu) under Grant agreement No. 801809. IMEDEA is an accredited “Maria de Maeztu Excellence Unit” (Grant CEX2021-001198, funded by MICIU/AEI/10.13039/501100011033). K.I.K. acknowledges support by the Innovative Technology Development Program for High-level waste management of the National Research Foundation of Korea funded by the Korean government (Ministry of Science and ICT) (Grant No. 2021M2E3A2041312). K.-B.M. and H.Y. were supported by a grant from the Human Resources Development program (No. 20204010600250) of the Korea Institute of Energy Technology Evaluation and Planning, funded by the Ministry of Trade, Industry, and Energy of the Korean Government., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2021-001198)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Characterization of Hydraulic Rock Diffusivity Using Oscillatory Pore Pressure

  • Sciandra, Dario
  • Kivi, Iman Rahimzadeh
  • Makhnenko, Roman Y.
  • Rebscher, Dorothee
  • Vilarrasa, Víctor
The interest of exploring deep geological resources for energy-related activities is rapidly increasing. Lowering the risks associated with these activities requires the development of fast and accurate in situ rock characterization methods. Monitoring and interpreting periodic signals, whether natural or man-induced, can provide valuable information about subsurface formations. This study focuses on improving the understanding of injection-induced pore pressure oscillations in confined formations and describes the use of periodic signals for characterizing hydraulic diffusivity. We revisit existing analytical solutions of cyclic pore pressure diffusion into geologic formations with one-dimensional or axisymmetric geometries and compare their performance with numerical simulations, including uncoupled hydraulic (H) and coupled hydro-mechanical (HM) models. We investigate the solutions in three main applications: (a) energy storage in porous rock, (b) CO₂-rich water injection into a caprock representative for CO2 storage, and (c) stimulation of an enhanced geothermal system in crystalline rock. The wave propagation extends over kilometer scales for the first case. In the second case, the wave propagation is confined to tens of centimeters. For the last case, the wave propagation occurs on the order of tens of meters. Numerical and analytical solutions match under identical assumptions, with errors of less than 3% across all the considered cases. While numerical solutions account for multidimensional hydro-mechanical rock response, analytical solutions provide an immediate initial approximation of the problem, enabling rapid reactions. This study highlights how simplified tools can aid in real-time interpretation for diverse subsurface energy applications, bridging analytical and numerical approaches for practical subsurface monitoring and characterization., Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature. D.S., V.V., and I.R.K. acknowledge funding from the European Research Council (ERC) under the European Union’s Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (www.georest.eu) under Grant agreement No. 801809. I.R.K. and V.V. also acknowledge support by the PCI2021-122077-2B project (www.easygeocarbon.com) funded by MCIN/AEI/https://doi.org/10.13039/501100011033 and the European Union NextGenerationEU/PRTR. I.R.K. also acknowledges funding from the Engineering and Physical Sciences Research Council through the UKRI Postdoc Guarantee Award THMC4CCS [Grant number EP/X026019/1]. IDAEA-CSIC is a Centre of Excellence Severo Ochoa (Spanish Ministry of Science, Innovation and Universities, Project CEX2018-000794-S). IMEDEA is an accredited "Maria de Maeztu Excellence Unit" (Grant CEX2021-001198, funded by MICIU/AEI/https://doi.org/10.13039/501100011033). R.M. acknowledges the support from US National Science Foundation, grant CMMI-2239630., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2018-000794-S)2, With funding from the Spanish government through the "Maria de Maeztu Centre of Excellence" accreditation (CEX2021-001198)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

On the limitations of closed-loop geothermal systems for electricity generation outside high-geothermal gradient fields

  • Tangirala, Sri Kalyan
  • Vilarrasa, Víctor
Closed-Loop Geothermal Systems (CLGS) involve connecting the injection and production wells through several borehole-sized parallel laterals instead of circulating a working fluid through a fracture network. Companies have garnered millions of dollars in investments on the claim that CLGS is truly scalable for both heating and electricity generation purposes. We show that high flow rates in the laterals lead to a steep drop in production temperatures because of a rapid cooling of the rock matrix surrounding the wells. Overcoming this physical limitation of CLGS demands an expensive task of drilling several multilaterals to reduce the lateral flow rate. Yet, simulation results indicate that, for a reservoir temperature of 180 °C, the total revenue of these systems fail to recover the lifetime costs incurred, even with 30 multilaterals and a production rate of 75 kg/s, which clearly indicates that CLGS are not scalable for solely electricity generation., The authors acknowledge funding from the European Research Council (ERC) under the European Union’s Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (www.georest.eu) under Grant agreement No. 801809. IMEDEA is an accredited “Maria de Maeztu Excellence Unit” (Grant CEX2021-001198, funded by MICIU/AEI/10.13039/501100011033). We acknowledge support from the Spanish Ministry of Science, Innovation and Universities through the project HydroPoreII (PID2022-137652NB-C44)., With funding from the Spanish government through the "Maria de Maeztu Centre of Excellence" accreditation (CEX2021-001198)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Understanding post-injection seismicity: Causes and mechanisms of trailing earthquakes in Enhanced Geothermal Systems

  • Boyet, Auregan
  • De Simone, Silvia
  • Cappa, Frédéric
  • Vilarrasa, Víctor
Enhanced Geothermal Systems (EGS) employ fluid injection for both reservoir stimulation and circulation, a practice that may sometimes induce earthquakes. Paradoxically, numerous EGS projects have observed the occurrence of the largest-magnitude earthquake (LME, 1.6 < M < 5.5) after injection cessation, posing a significant challenge for the development of geothermal power plants. This paper aims to examine the cases of postinjection LME observed in EGS, and provide a detailed understanding of the coupled mechanisms responsible for seismic activity during and after fluid injection. We report the mechanisms that have been hypothesised for different cases of LME emerging in the post-injection phase of EGS. The analysis of post-injection LME cases reveals two types of seismicity, early and late, differentiated by the time at which pore pressure changes become negligible, i.e., a post-injection time longer than the injection time. Notably, we remark that, for most cases of early post-injection high-magnitude earthquakes, the primary triggering mechanisms involve pore pressure diffusion, thermal effects, poromechanical stress relaxation and static stress transfer resulting from seismic fault slip. Conversely, prolonged fluid injections could lead to the gradual accumulation of stress on faults, mainly due to aseismic slip, causing late post-injection LME. Furthermore, recent studies have also demonstrated the importance of the initial fault stress criticality in influencing the post-injection behaviour of fault aseismic slip and trailing seismicity. Finally, we present recent efforts devoted to develop effective methodologies for mitigating induced seismicity, and the current research perspectives aimed at forecasting and minimizing seismic activity associated with EGS., A.B. and V.V. acknowledge funding from the European Research Council (ERC) under the European Union’s Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (www.georest.eu) under Grant agreement No. 801809. S.D.S. and V.V. acknowledge support from the Spanish Ministry of Science, Innovation and Universities through project HydroPoreII (PID2022-137652NB- C44). IMEDEA is an accredited "Maria de Maeztu Excellence Unit" (Grant CEX2021-001198, funded by MICIU/AEI/10.13039/ 501100011033). S.D.S. acknowledges the support by MICIU/AEI/ 10.13039/501100011033 and by the “European Union Next Generation EU/PRTR” through the ‘Ramón y Cajal’ fellowship (reference RYC2021- 032780-I). F.C. acknowledges the financial support by the Agence Nationale de la Recherche (ANR) through the INSeiS project under contract ANR-22-CE49-0018 (PI: L. De Barros, Universit´e Cˆote d’Azur, France) and the Institut Universitaire de France (IUF)., With funding from the Spanish government through the "Maria de Maeztu Centre of Excellence" accreditation (CEX2021-001198)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

A review of thermo-hydro-mechanical modeling of coupled processes in fractured rock: From continuum to discontinuum perspective

  • Vaezi, Iman
  • Yoshioka, Keita
  • De Simone, Silvia
  • Gómez-Castro, Berta María
  • Paluszny, Adriana
  • Jalali, Mohammadreza
  • Berre, Inga
  • Rutqvist, Jonny
  • Min, Ki Bok
  • Lei, Qinghua
  • Makhnenko, Roman Y.
  • Hu, Mengsu
  • Tsang, Chin Fu
  • Vilarrasa, Víctor
Coupled thermo-hydro-mechanical (THM) processes in fractured rock are playing a crucial role in geoscience and geoengineering applications. Diverse and conceptually distinct approaches have emerged over the past decades in both continuum and discontinuum perspectives leading to significant progress in their comprehending and modeling. This review paper offers an integrated perspective on existing modeling methodologies providing guidance for model selection based on the initial and boundary conditions. By comparing various models, one can better assess the uncertainties in predictions, particularly those related to the conceptual models. The review explores how these methodologies have significantly enhanced the fundamental understanding of how fractures respond to fluid injection and production, and improved predictive capabilities pertaining to coupled processes within fractured systems. It emphasizes the importance of utilizing advanced computational technologies and thoroughly considering fundamental theories and principles established through past experimental evidence and practical experience. The selection and calibration of model parameters should be based on typical ranges and applied to the specific conditions of applications. The challenges arising from inherent heterogeneity and uncertainties, nonlinear THM coupled processes, scale dependence, and computational limitations in representing field scale fractures are discussed. Realizing potential advances on computational capacity calls for methodical conceptualization, mathematical modeling, selection of numerical solution strategies, implementation, and calibration to foster simulation outcomes that intricately reflect the nuanced complexities of geological phenomena. Future research efforts should focus on innovative approaches to tackle the hurdles and advance the state-of-the-art in this critical field of study., I.V. and V.V. acknowledge funding from the European Research Council (ERC) under the European Union’s Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (grant agreement No. 801809). S.D.S. acknowledges the support by MICIU/AEI/10.13039/501100011033 and by "European Union Next Generation EU/PRTR" through the ‘Ramón y Cajal’ fellowship (reference RYC2021-032780-I). S.D.S. and V.V. acknowledge the funding by MICIU/AEI/10.13039/501100011033 and by “ERDF, EU” through the ‘HydroPoreII’ project (reference PID2022-137652NB-C44). K.B.M. is grateful for the support by the Institute for Korea Spent Nuclear Fuel (iKSNF) and National Research Foundation of Korea (NRF) grant funded by the Korea government (Ministry of Science and ICT, MSIT) (2021M2E1A1085196). Q.L. is grateful for the support by the Swedish Radiation Safety (SSM), Swedish Transport Administration (Trafikverket), Swedish Rock Engineering Foundation (BeFo), and Nordic Energy Research (Grant 187658). M.H.’s and J.R.’s contribution to this review was supported by the US Department of Energy (DOE), the Office of Nuclear Energy, Spent Fuel and Waste Science and Technology Campaign, and by the US Department of Energy (DOE), the Office of Basic Energy Sciences, Chemical Sciences, Geosciences, and Biosciences Division both under Contract Number DE-AC02-05CH11231 with Lawrence Berkeley National Laboratory. R.M. acknowledges the support from the US National Science Foundation (grant CMMI-2239630). I.B. acknowledges funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme (grant agreement No. 101002507). A.P. thanks the UK Natural Environment Research Council (NERC) for funding SeisGreen Project (Grant No. NE/W009293/1) which supported this work. A.P. also thanks the Royal Society UK for supporting this research through fellowship UF160443. IMEDEA is an accredited "Maria de Maeztu Excellence Unit" (Grant CEX2021-001198, funded by MICIU/AEI/10.13039/501100011033)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Revealing hydro-mechanical properties of a natural fracture in low-permeable shale

  • Sciandra, Dario
  • Kim, Hyunbin
  • Makhnenko, Roman Y.
  • Kivi, Iman Rahimzadeh
  • Vilarrasa, Víctor
Shales are considered to be sealing units for geological carbon storage and suitable host rocks for nuclear waste repositories due to their low permeability. However, the presence of fractures within these formations can significantly alter their flow, transport, and deformation behavior, which is central to the safe implementation of underground storage projects. Fractures not only increase the overall permeability of the rock but also contribute to its anisotropic behavior. This study focuses on characterizing the hydro-mechanical response of a natural fracture to aqueous fluid injection within a shaly specimen of Opalinus Clay. Laboratory experiments were performed to measure the mechanical and flow properties of intact and fractured rock specimens. Subsequently, a three-dimensional (3D) numerical model of water injection into the fractured specimen was developed. This model explicitly accounts for fracture geometry with strain-dependent aperture changes based on the cubic law assumption. Experimental measurements indicate that the fractured shale exhibits permeability up to two orders of magnitude higher than that of the intact counterpart. However, the simulations reveal that fracture permeability locally spans up to eight orders of magnitude. This significant change in permeability affects fluid flow within the rock specimen. The numerical model best reproduces the experimental results for a normal stiffness of the natural fracture of 18.7 MPa/mm at effective mean stresses below 15 MPa, and of 187.2 MPa/mm at higher confinements. This outcome highlights the critical importance of defining the hydro-mechanical parameters of fractures under realistic effective stress conditions with far-reaching implications for secure underground storage., Dario Sciandra, Iman R. Kivi, and Víctor Vilarrasa acknowledge the funding from the European Research Council (ERC) under the European Union's Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (www.georest.eu) under Grant agreement No. 801809. IMEDEA is an accredited "Maria de Maeztu Excellence Unit” (Grant CEX2021-001198, funded by MICIU/AEI/10.13039/501100011033). Iman R. Kivi also acknowledges the funding from the Engineering and Physical Sciences Research Council through the UKRI Postdoc Guarantee Award THMC4CCS (Grant No. EP/X026019/1). Hyunbin Kim and Roman Y. Makhnenko are supported by the US National Science Foundation (Grant No. CMMI-2239630)., With funding from the Spanish government through the "Maria de Maeztu Centre of Excellence" accreditation (CEX2021-001198)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Bridging the Gap for Sparse Observations: Data-Driven Versus Physics-Informed Neural Networks for a Transient Flow Problem in a Heterogeneous Porous Medium

  • Walter, Linus
  • Parisio, Francesco
  • Kong, Qingkai
  • Hanson-Hedgecock, Sara
  • Vilarrasa, Víctor
Assimilating field data is essential to calibrate rock properties in hydrogeological applications. While such workflows are challenging for physics-based reservoir simulators, data-driven Artificial Neural Networks (ANN) offer a potential solution by effectively managing noisy data to infer fluid pressure diffusion p(x,t). Nevertheless, the sparse observation wells in hydrogeology projects make training ANN models difficult. Therefore, we employ Physics-Informed Neural Networks (PINN) to bridge this gap between sparse spatial data. We train both ANN and PINN on a synthetic p(x,t) data set within a low-permeability porous medium containing a highly permeable material. Having an identical architecture, both models integrate direct observations of the target variable, while the PINN further optimizes the diffusion equation residual. By comparing the model output as a function of the number of observation wells, we find that the PINN outperforms the ANN when spatial observations are limited to a small number of wells. Adding noise to the training data further underscores the robustness of PINN against random measurement errors or ambient noise. Furthermore, we evaluate the effectiveness of PINN in representing a high-permeability zone without observations inside the domain. The findings suggest that accuracy is maintained even with reduced thickness of the equivalent material, although this leads to an increase in computation time. Given the sparsity of observation wells in hydrogeological applications, PINNs potentially provide a more suitable machine learning workflow than purely data-driven ANN for reservoir modeling., [Plain Language Summary] In hydrogeology, computational reservoir models simulate how underground reservoirs, such as aquifers, respond to water injection or extraction. Typically, these models use physics-based approaches that require real-world data for calibration, although the integration of large and noisy data sets poses a challenge to these models. Artificial Neural Networks (ANN) have shown promise as an alternative because they can handle noisy data more easily. However, while observation wells provide abundant data over time, their spatial distribution is often sparse, making it difficult to train ANN effectively. Physics-Informed Neural Networks (PINN) are an extension of ANN that bridge this spatial gap by incorporating physical conditions into their solution. We test ANN and PINN on simulated data to see how they perform when predicting fluid pressure in a low-permeable porous material that host a high-permeable material. Our results show that PINN outperforms ANN when few observation wells are available, and PINN also proves to be more robust against errors in the data. However, accurately modeling sharp permeability jumps, such as occurring at material boundaries, with PINN can increase the computation time. Overall, PINN show strong potential for reservoir modeling in hydrogeology, particularly in cases where few observation wells are available for data collection., LW, FP, SHH, and VV acknowledge funding from the European Research Council (ERC) under the European Union's Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (www.georest.eu) under Grant Agreement No. 801809. IMEDEA is an accredited “Maria de Maeztu Excellence Unit” (Grant CEX2021-001198, funded by MICIU/AEI/10.13039/501100011033). QK's work is under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under contract DE-AC52 07NA27344. This paper is released under LLNL-JRNL-868932. VV acknowledges support from the Spanish Ministry of Science, Innovation and Universities through project HydroPoreII (PID2022-137652NB-C44)., With funding from the Spanish government through the "Maria de Maeztu Centre of Excellence" accreditation (CEX2021-001198)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Stochastic poromechanical analysis forecasts a notable exceedance probability for the 2017 Pohang, South Korea, Mw 5.5 earthquake

  • Wu, Haiqing
  • Vilarrasa, Víctor
  • Parisio, Francesco
  • Alcolea, Andrés
  • Meier, Peter
  • Carrera, Jesús
  • Saaltink, Maarten W.
The 2017 Pohang Mw 5.5 earthquake is currently the largest seismic event induced by Enhanced Geothermal Systems. The high uncertainty on geological and mechanical conditions of the rupture fault of this earthquake has originated a debate on its triggering mechanisms. Here, we propose a stochastic poromechanical analysis approach that combines Monte Carlo sampling and poromechanical models to address the uncertainty problem. By conducting a large number of coupled poromechanical simulations varying the uncertain geomechanical parameters, we yield an exceedance probability of 7%-15% for the Pohang mainshock. Remarkably, this physics-based stochastic prior forecast is quite comparable to the posterior likelihood inferred from the magnitude-frequency relationship of recorded seismicity. Our results reveal a scaling relationship between the earthquake magnitude and the initial fault stability, which indicates a threshold of the initial Coulomb Failure Stress to differentiate if faults are initially, critically stressed, and thus, the earthquake magnitude. This Pohang threshold is −0.2 to −0.1 MPa, about one order of magnitude larger than that proposed for natural earthquakes. This study highlights that the reactivation of critically stressed faults may trigger damaging earthquakes even for small poromechanical perturbations and opens a promising avenue for assessing the likelihood of induced earthquakes based on physical understanding., H.W. acknowledge the financial support of the Secretariat for Universities and Research of the Ministry of Business and Knowledge of the Government of Catalonia (AGAUR) and the European Social Fund (FI−2019). H.W. also acknowledges the Becas Santander Research Scholarship from the Technical University of Catalonia (UPC) and the Santander. V.V. acknowledges funding from the European Research Council (ERC) under the European Union’s Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (www.georest.eu) under Grant agreement No. 801809 and support from the Spanish Ministry of Science, Innovation and Universities through project HydroPoreII (PID2022-137652NB-C44). IMEDEA is an accredited “Maria de Maeztu Excellence Unit” (Grant CEX2021-001198, funded by MICIU/AEI/10.13039/501100011033). V.V. and F.P. acknowledge funding from the European Union’s Horizon 2020 Research and Innovation Program through the Marie Sklodowska-Curie Action ARMISTICE under grant agreement No. 882733. A.A. and P.M. acknowledge the financial support from the Swiss Federal Office of Energy within the framework of the ZoDrEx GEOTHERMICA project under contract SI/501720-01. M.S. acknowledges financial support from the “HEATSTORE” project (170153–44011), which has been subsidized through the ERANET Cofund GEOTHERMICA (Grant agreement no. 731117), from the European Commission and the Spanish Ministry of Science, Innovation and Universities (PCI2018-092933). J.C. acknowledges support of the EU through “Eastern Lights” project under Grant Agreement number 101136122., With funding from the Spanish government through the "Maria de Maeztu Centre of Excellence" accreditation (CEX2021-001198)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

WellPINN: Accurate Well Representation for Transient Fluid Pressure Diffusion in Subsurface Reservoirs With Physics-Informed Neural Networks

  • Walter, Linus
  • Kong, Qingkai
  • Hanson-Hedgecock, Sara
  • Vilarrasa, Víctor
Accurate representation of pumping wells is essential for reliable reservoir characterization and simulation of operational scenarios in subsurface flow models. Physics-informed neural networks (PINNs) are emerging as a promising alternative to numerical models for reservoir modeling, offering seamless integration of monitoring data and governing physical equations. However, existing PINN-based studies face major challenges in capturing fluid pressure near wells when using a source/sink term, particularly during the early stages after pumping begins. We address this problem by introducing WellPINN, a workflow in which an initially trained PINN infers fluid pressure across the entire reservoir domain using a large equivalent well radius. This initial PINN solution is then locally refined around the well by a set of subdomain PINNs that are trained for smaller equivalent well radii. Continuity across these subdomain interfaces as well as at the initial condition is ensured by hard-constraining each PINN on its subdomain boundary. Our results demonstrate WellPINN as the first workflow of its kind to focus on accurate inference of fluid pressure from pumping rates throughout the entire injection period, significantly advancing the potential of PINNs for inverse modeling and operational scenario simulations. All data and code for this paper are openly available at https://doi.org/10.20350/DIGITALCSIC/17260, W, SHH and VV acknowledge funding from the European Research Council (ERC) under the European Union's Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (www.georest.eu) under Grant Agreement No. 801809. IMEDEA is an accredited “Maria de Maeztu Excellence Unit” (Grant CEX2021-001198, funded by MICIU/AEI/10.13039/501100011033). QK's work is supported by LDRD at LLNL (24-ERD-012). The work of QK is under the auspices of the US Department of Energy by Lawrence Livermore National Laboratory under contract DE-AC52-07NA27344., With funding from the Spanish government through the "Maria de Maeztu Centre of Excellence" accreditation (CEX2021-001198)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Injection-induced poroelastic controls on the transient process of dynamic fault rupture in geo-energy engineering

  • Wu, Haiqing
  • Parisio, Francesco
  • Vilarrasa, Víctor
Managing fluid-induced seismicity is one of the most crucial challenges in geo-energy engineering. A seismic event usually starts from initial fault slip, followed by a nucleation process, and finally propagates to dynamic rupture. Fault stability analysis based on the elastostatic Mohr-Coulomb failure criterion is limited to assess fault slip initiation only. In contrast, the interfacial slip model of cracks is well suited to describe the nucleation process and the initiation of dynamic rupture in addition to the initial slip. Moreover, it provides an opportunity to identify the distinguished slip regimes of dynamic fault rupture under various geomechanical conditions compared with other fully numerical approaches. Yet, existing studies following this model have not accounted for injection-induced poroelastic effects on the nucleation process and slip regimes. Here, we incorporate a well-established analytical solution of poroelastic stress instead of numerical reservoir tools into the interfacial slip model to simulate the earthquake nucleation process and slip regimes due to injecting fluid into a fault zone. Results highlight that the developed model is capable of capturing the failure transition from initial slip to dynamic rupture propagation. Including injection-induced poroelastic stress variations significantly impacts the specific evolution of crack growth, disclosing the poroelasticity-dominated nucleation in addition to that dominated by slip-weakening mechanism, which brings to light a wider range of slip regimes in nucleation process. Poroelasticity can stabilize faults by delaying the initiation of fault slip and its ultimate nucleation, which are beneficial for managing induced seismicity. However, it also leads to a potential risk of inducing damaging earthquakes, owing to the issue of long run-out distance, under certain conditions. These findings arise from a physics-based model and provide a better understanding of the transient rupture process, contributing to developing managing and forecasting tools of induced seismicity., H.W. would like to acknowledge the financial support received from the Secretariat for Universities and Research of the Ministry of Business and Knowledge of the Government of Catalonia (AGAUR) and the European Social Fund (FI-2019). H.W. also acknowledges the Becas Santander Research Scholarship from the Technical University of Catalonia (UPC) and the Santander. V.V. acknowledges funding from the European Research Council (ERC) under the European Union’s Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (www.georest.eu) under Grant agreement No. 801809 and under Horizon Europe through the Proof of Concept NOSHAKE under Grant Agreement No. 101248689. IMEDEA is an accredited “Maria de Maeztu Excellence Unit” (Grant CEX2021-001198, funded by MCIN/AEI/10.13039/501100011033)., With funding from the Spanish government through the "Maria de Maeztu Centre of Excellence" accreditation (CEX2021-001198)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

On the Leaky Nature of Fractures in Low-Permeability Rock

  • Vaezi, Iman
  • Parisio, Francesco
  • Yoshioka, Keita
  • Vilarrasa, Víctor
Hydraulic-test interpretation in fractured rock commonly assumes impermeable confining matrices, an assumption we show is systematically incorrect, even when the matrices are 7–14 orders of magnitude less permeable than the fracture. Fluid injected into a fracture begins to leak into the surrounding rock matrices within milliseconds to seconds, causing the slope of the pressure evolution with respect to the logarithm of time to halve, equivalent to a factor-of-two overestimation of fracture transmissivity if leakage is neglected. Here, we investigate the flow regimes induced by constant flow rate water injection into a fracture surrounded by low-permeability matrices and the implications for hydraulic-test interpretation. We find that even for a low-permeability confining rock matrix, leakage is non-negligible on the pressure evolution due to the small fracture aperture, which leads to a large pressure gradient between the fracture and matrix. Negligible leakage exists only for an extremely short period, and then a transient flow regime arises with a slope of −1/4 in the log-log derivative plot, that is, flow dimension equal to 2.5. Subsequently, the flow regime becomes radial, with the slope of pressure evolution in a semi-log plot corresponding to that of a leaky aquifer, that is, twice the actual fracture transmissivity. We validate this finding against step-rate injection data from the Bedretto Underground Laboratory, for which only the model accounting for matrix leakage reproduces the measured pressure evolution. As a result, one could mistakenly overestimate the fracture transmissivity in injection tests in fractured media if the leaky nature of fractures is not considered., [ Plain Language Summary] Geo-resources play an important role in decarbonization. Geo-energy technologies usually require fluid injection and/or production in fractured rock masses, in which the fracture permeability is between 7 and 14 orders of magnitude higher than the rock-matrix permeability. For this reason, it is usually assumed that the matrix can be considered impermeable, which implies that no leakage can occur from the fracture into the rock matrix. Here, we study the hydraulic response to fluid injection into a fracture surrounded by low-permeability matrices. We show that leakage of the injected fluid into the surrounding low-permeability rock matrices becomes non-negligible within a few seconds, significantly affecting the pressure evolution. The pressure increase induced by water injection follows a straight line with the logarithm of time. This slope becomes half of the initial slope as a result of leakage within less than a few seconds. Thus, neglecting leakage into the low-permeability matrix would lead to erroneous interpretation of hydraulic tests that would yield inaccurate simulation results. We validate our findings against a field injection experiment in crystalline rock at the Bedretto Underground Laboratory, in Switzerland, confirming that ignoring matrix leakage leads to systematic and significant errors in fracture characterization., I.V. and V.V. acknowledge funding from the European Research Council (ERC) under the European Union's Horizon 2020 Research and Innovation Programme through the Starting Grant GEoREST (www.georest.eu), under grant agreement No. 801809. V.V. acknowledges support from the Spanish Ministry of Science, Innovation and Universities through project HydroPoreII (PID2022-137652NB-C44). K.Y. was supported in part by the Austrian Science Fund (FWF) Grant 10.55776/PIN9246524. IMEDEA is an accredited “Maria de Maeztu Excellence Unit” (Grant CEX2021-001198, funded by MICIU/AEI/10.13039/501100011033)., With funding from the Spanish government through the "Maria de Maeztu Centre of Excellence" accreditation (CEX2021-001198)., Peer reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Stochastic poromechanical analysis forecasts a notable exceedance probability for the 2017 Pohang, South Korea, Mw 5.5 earthquake

  • Wu, Haiqing|||0000-0002-0806-2471
  • Vilarrasa Riaño, Víctor|||0000-0003-1169-4469
  • Parisio, Francesco
  • Alcolea Rodríguez, Andrés
  • Meier, Peter
  • Carrera Ramírez, Jesús|||0000-0002-8054-4352
  • Saaltink, Maarten Willem|||0000-0003-0553-4573
The 2017 Pohang Mw 5.5 earthquake is currently the largest seismic event induced by Enhanced Geothermal Systems. The high uncertainty on geological and mechanical conditions of the rupture fault of this earthquake has originated a debate on its triggering mechanisms. Here, we propose a stochastic poromechanical analysis approach that combines Monte Carlo sampling and poromechanical models to address the uncertainty problem. By conducting a large number of coupled poromechanical simulations varying the uncertain geomechanical parameters, we yield an exceedance probability of 7%-15% for the Pohang mainshock. Remarkably, this physics-based stochastic prior forecast is quite comparable to the posterior likelihood inferred from the magnitude-frequency relationship of recorded seismicity. Our results reveal a scaling relationship between the earthquake magnitude and the initial fault stability, which indicates a threshold of the initial Coulomb Failure Stress to differentiate if faults are initially, critically stressed, and thus, the earthquake magnitude. This Pohang threshold is -0.2 to -0.1¿MPa, about one order of magnitude larger than that proposed for natural earthquakes. This study highlights that the reactivation of critically stressed faults may trigger damaging earthquakes even for small poromechanical perturbations and opens a promising avenue for assessing the likelihood of induced earthquakes based on physical understanding., H.W. acknowledge the financial support of the Secretariat for Universities and Research of the Ministry of Business and Knowledge of the Government of Catalonia (AGAUR) and the European Social Fund (FI−2019). H.W. also acknowledges the Becas Santander Research Scholarship from the Technical University of Catalonia (UPC) and the Santander. V.V. acknowledges funding from the European Research Council (ERC) under the European Union’s Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (www.georest.eu) under Grant agreement No. 801809 and support from the Spanish Ministry of Science, Innovation and Universities through project HydroPoreII (PID2022-137652NB-C44). IMEDEA is an accredited “Maria de Maeztu Excellence Unit” (Grant CEX2021-001198, funded by MICIU/AEI/10.13039/501100011033). V.V. and F.P. acknowledge funding from the European Union’s Horizon 2020 Research and Innovation Program through the Marie Sklodowska-Curie Action ARMISTICE under grant agreement No. 882733. A.A. and P.M. acknowledge the financial support from the Swiss Federal Office of Energy within the framework of the ZoDrEx GEOTHERMICA project under contract SI/501720-01. M.S. acknowledges financial support from the “HEATSTORE” project (170153–44011), which has been subsidized through the ERANET Cofund GEOTHERMICA (Grant agreement no. 731117), from the European Commission and the Spanish Ministry of Science, Innovation and Universities (PCI2018-092933). J.C. acknowledges support of the EU through “Eastern Lights” project under Grant Agreement number 101136122., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Multiple induced seismicity mechanisms at Castor underground gas storage illustrate the need for thorough monitoring

  • Vilarrasa, Victor
  • De Simone, Silvia|||0000-0002-3647-7869
  • Carrera Ramírez, Jesús|||0000-0002-8054-4352
  • Villaseñor Hidalgo, Antonio
V.V. acknowledges funding from the European Research Council (ERC) under the European Union’s Horizon 2020 Research and Innovation Programme through the Starting Grant GEoREST (www.georest.eu) under grant agreement No. 801809. A.V. acknowledges funding from Spanish Ministry of Science and Innovation grant CGL2017-88864-R. IDAEA-CSIC and ICM-CSIC are Centres of Excellence Severo Ochoa (Spanish Ministry of Science and Innovation Grants CEX2018-000794-S and CEX2019-000928-S, respectively, funded by MCIN/AEI/ 10.13039/501100011033)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Induced seismicity in geologic carbon storage

  • Vilarrasa Riaño, Víctor|||0000-0003-1169-4469
  • Carrera Ramírez, Jesús|||0000-0002-8054-4352
  • Olivella Pastallé, Sebastià|||0000-0003-3976-4027
  • Rutqvist, Jonny
  • Laloui, Lyesse
Geologic carbon storage, as well as other geo-energy applications, such as geothermal energy, seasonal natural gas storage and subsurface energy storage imply fluid injection and/or extraction that causes changes in rock stress field and may induce (micro)seismicity. If felt, seismicity has a negative effect on public perception and may jeopardize wellbore stability and damage infrastructure. Thus, induced earthquakes should be minimized to successfully deploy geo-energies. However, numerous processes may trigger induced seismicity, which contribute to making it complex and translates into a limited forecast ability of current predictive models. We review the triggering mechanisms of induced seismicity. Specifically, we analyze (1) the impact of pore pressure evolution and the effect that properties of the injected fluid have on fracture and/or fault stability; (2) non-isothermal effects caused by the fact that the injected fluid usually reaches the injection formation at a lower temperature than that of the rock, inducing rock contraction, thermal stress reduction and stress redistribution around the cooled region; (3) local stress changes induced when low-permeability faults cross the injection formation, which may reduce their stability and eventually cause fault reactivation; (4) stress transfer caused by seismic or aseismic slip; and (5) geochemical effects, which may be especially relevant in carbonate-containing formations. We also review characterization techniques developed by the authors to reduce the uncertainty in rock properties and subsurface heterogeneity both for the screening of injection sites and for the operation of projects. Based on the review, we propose a methodology based on proper site characterization, monitoring and pressure management to minimize induced seismicity., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Implicit hydromechanical representation of fractures using a continuum approach

  • Vaezi Anzeha, Iman
  • Parisio, Francesco
  • Keita, Yoshioka
  • Alcolea, Andrés
  • Meier, Peter
  • Carrera, Jesús
  • Olivella Pastallé, Sebastià|||0000-0003-3976-4027
  • Vilarrasa Riaño, Víctor|||0000-0003-1169-4469
Fractures control fluid flow, solute transport, and mechanical deformation in crystalline media. They can be modeled numerically either explicitly or implicitly via an equivalent continuum. The implicit framework implies lower computational cost and complexity. However, upscaling heterogeneous fracture properties for its implicit representation as an equivalent fracture layer remains an open question. In this study, we propose an approach, the Equivalent Fracture Layer (EFL), for the implicit representation of fractures surrounded by low-permeability rock matrix to accurately simulate hydromechanical coupled processes. The approach assimilates fractures as equivalent continua with a manageable scale (»1 µm) that facilitates spatial discretization, even for large-scale models including multiple fractures. Simulation results demonstrate that a relatively thick equivalent continuum layer (in the order of cm) can represent a fracture (with aperture in the order of µm) and accurately reproduce the hydromechanical behavior (i.e., fluid flow and deformation/stress behavior). There is an upper bound restriction due to the Young's modulus because the equivalent fracture layer should have a lower Young's modulus than that of the surrounding matrix. To validate the approach, we model a hydraulic stimulation carried out at the Bedretto Underground Laboratory for Geosciences and Geoenergies in Switzerland by comparing numerical results against measured data. The method further improves the ability and simplicity of continuum methods to represent fractures in fractured media., I.V. and V.V. acknowledge funding from the European Research Council (ERC) under the European Union's Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (www.georest.eu), under grant agreement No. 801809. J.C. and V.V. acknowledge financial support from the “ZoDrEx” project, which has been subsidized through the ERANET Cofund GEOTHERMICA (Project no. 731117), from the European Commission and the Spanish Ministry of Economy, Industry and Competitiveness (MINECO). The work of Geo-Energie Suisse AG was financially supported by the Swiss Federal Office of Energy within the framework of the ZoDrEx GEOTHERMICA project under contract SI/501720-01. F. P. acknowledges funding from the European Union's Horizon 2020 Research and Innovation Program through the Marie Sklowdowska-Curie Individual Fellowship ARMISTICE, Spain under Grant Agreement No. 882733. K.Y. acknowledges funding from EURAD, the European Joint Programme on Radioactive Waste Management through the project DONUT (Grant No 847593). IMEDEA is an accredited "Maria de Maeztu Excellence Unit" (Grant CEX2021-001198, funded by MCIN/AEI/10.13039/501100011033). IDAEA-CSIC is a Center of Excellence Severo Ochoa (Spanish Ministry of Science and Innovation, Project CEX2018-000794-S)., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Implicit hydromechanical representation of fractures using a continuum approach

  • Vaezi Anzeha, Iman
  • Parisio, Francesco
  • Keita, Yoshioka
  • Alcolea, Andrés
  • Meier, Peter
  • Carrera, Jesús
  • Olivella Pastallé, Sebastià
  • Vilarrasa Riaño, Víctor
Fractures control fluid flow, solute transport, and mechanical deformation in crystalline media. They can be modeled numerically either explicitly or implicitly via an equivalent continuum. The implicit framework implies lower computational cost and complexity. However, upscaling heterogeneous fracture properties for its implicit representation as an equivalent fracture layer remains an open question. In this study, we propose an approach, the Equivalent Fracture Layer (EFL), for the implicit representation of fractures surrounded by low-permeability rock matrix to accurately simulate hydromechanical coupled processes. The approach assimilates fractures as equivalent continua with a manageable scale (»1 µm) that facilitates spatial discretization, even for large-scale models including multiple fractures. Simulation results demonstrate that a relatively thick equivalent continuum layer (in the order of cm) can represent a fracture (with aperture in the order of µm) and accurately reproduce the hydromechanical behavior (i.e., fluid flow and deformation/stress behavior). There is an upper bound restriction due to the Young's modulus because the equivalent fracture layer should have a lower Young's modulus than that of the surrounding matrix. To validate the approach, we model a hydraulic stimulation carried out at the Bedretto Underground Laboratory for Geosciences and Geoenergies in Switzerland by comparing numerical results against measured data. The method further improves the ability and simplicity of continuum methods to represent fractures in fractured media., I.V. and V.V. acknowledge funding from the European Research Council (ERC) under the European Union's Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (www.georest.eu), under grant agreement No. 801809. J.C. and V.V. acknowledge financial support from the “ZoDrEx” project, which has been subsidized through the ERANET Cofund GEOTHERMICA (Project no. 731117), from the European Commission and the Spanish Ministry of Economy, Industry and Competitiveness (MINECO). The work of Geo-Energie Suisse AG was financially supported by the Swiss Federal Office of Energy within the framework of the ZoDrEx GEOTHERMICA project under contract SI/501720-01. F. P. acknowledges funding from the European Union's Horizon 2020 Research and Innovation Program through the Marie Sklowdowska-Curie Individual Fellowship ARMISTICE, Spain under Grant Agreement No. 882733. K.Y. acknowledges funding from EURAD, the European Joint Programme on Radioactive Waste Management through the project DONUT (Grant No 847593). IMEDEA is an accredited "Maria de Maeztu Excellence Unit" (Grant CEX2021-001198, funded by MCIN/AEI/10.13039/501100011033). IDAEA-CSIC is a Center of Excellence Severo Ochoa (Spanish Ministry of Science and Innovation, Project CEX2018-000794-S)., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Stochastic poromechanical analysis forecasts a notable exceedance probability for the 2017 Pohang, South Korea, Mw 5.5 earthquake

  • Wu, Haiqing
  • Vilarrasa Riaño, Víctor
  • Parisio, Francesco
  • Alcolea Rodríguez, Andrés
  • Meier, Peter
  • Carrera Ramírez, Jesús
  • Saaltink, Maarten Willem
The 2017 Pohang Mw 5.5 earthquake is currently the largest seismic event induced by Enhanced Geothermal Systems. The high uncertainty on geological and mechanical conditions of the rupture fault of this earthquake has originated a debate on its triggering mechanisms. Here, we propose a stochastic poromechanical analysis approach that combines Monte Carlo sampling and poromechanical models to address the uncertainty problem. By conducting a large number of coupled poromechanical simulations varying the uncertain geomechanical parameters, we yield an exceedance probability of 7%-15% for the Pohang mainshock. Remarkably, this physics-based stochastic prior forecast is quite comparable to the posterior likelihood inferred from the magnitude-frequency relationship of recorded seismicity. Our results reveal a scaling relationship between the earthquake magnitude and the initial fault stability, which indicates a threshold of the initial Coulomb Failure Stress to differentiate if faults are initially, critically stressed, and thus, the earthquake magnitude. This Pohang threshold is -0.2 to -0.1¿MPa, about one order of magnitude larger than that proposed for natural earthquakes. This study highlights that the reactivation of critically stressed faults may trigger damaging earthquakes even for small poromechanical perturbations and opens a promising avenue for assessing the likelihood of induced earthquakes based on physical understanding., H.W. acknowledge the financial support of the Secretariat for Universities and Research of the Ministry of Business and Knowledge of the Government of Catalonia (AGAUR) and the European Social Fund (FI−2019). H.W. also acknowledges the Becas Santander Research Scholarship from the Technical University of Catalonia (UPC) and the Santander. V.V. acknowledges funding from the European Research Council (ERC) under the European Union’s Horizon 2020 Research and Innovation Program through the Starting Grant GEoREST (www.georest.eu) under Grant agreement No. 801809 and support from the Spanish Ministry of Science, Innovation and Universities through project HydroPoreII (PID2022-137652NB-C44). IMEDEA is an accredited “Maria de Maeztu Excellence Unit” (Grant CEX2021-001198, funded by MICIU/AEI/10.13039/501100011033). V.V. and F.P. acknowledge funding from the European Union’s Horizon 2020 Research and Innovation Program through the Marie Sklodowska-Curie Action ARMISTICE under grant agreement No. 882733. A.A. and P.M. acknowledge the financial support from the Swiss Federal Office of Energy within the framework of the ZoDrEx GEOTHERMICA project under contract SI/501720-01. M.S. acknowledges financial support from the “HEATSTORE” project (170153–44011), which has been subsidized through the ERANET Cofund GEOTHERMICA (Grant agreement no. 731117), from the European Commission and the Spanish Ministry of Science, Innovation and Universities (PCI2018-092933). J.C. acknowledges support of the EU through “Eastern Lights” project under Grant Agreement number 101136122., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Hubs and clusters approach to unlock the development of carbon capture and storage - Case study in Spain

  • Sun, Xiaolong
  • Alcalde Martín, Juan
  • Bakhtbidar, M.
  • Elío, J.
  • Vilarrasa, V.
  • Canal, J.
  • Ballesteros, J.
  • Heinemann, N.
  • Haszeldine, S.
  • Cavanagh, A.
  • Vega-Maza, D.
  • Rubiera, F.
  • Martínez-Orio, R.
  • Johnson, G.
  • Carbonell, R.
  • Marzán, I.
  • Travé i Herrero, Anna
  • Gómez Rivas, Enrique
Many countries have assigned an indispensable role for carbon capture and storage (CCS) in their national climate change mitigation pathways. However, CCS deployment has stalled in most countries with only limited commercial projects realised mainly in hydrocarbon-rich countries for enhanced oil recovery. If the Paris Agreement is to be met, then this progress must be replicated widely, including hydrocarbon-limited countries. In this study, we present a novel source-to-sink assessment methodology based on a hubs and clusters approach to identify favourable regions for CCS deployment and attract renewed public and political interest in viable deployment pathways. Here, we apply this methodology to Spain, where fifteen emission hubs from both the power and the hard-to-abate industrial sectors are identified as potential CO2 sources. A priority storage structure and two reserves for each hub are selected based on screening and ranking processes using a multi-criteria decision-making method. The priority source-to-sink clusters are identified indicating four potential development regions, with the North-Western and North-Eastern Spain recognised as priority regions due to resilience provided by different types of CO2 sources and geological structures. Up to 68.7 Mt CO2 per year, comprising around 21% of Spanish emissions can be connected to clusters linked to feasible storage. CCS, especially in the hard-to-abate sector, and in combination with other low-carbon energies (e.g., blue hydrogen and bioenergy), remains a significant and unavoidable contributor to the Paris Agreement's mid-century net-zero target. This study shows that the hubs and clusters approach can facilitate CCS deployment in Spain and other hydrocarbon-limited countries.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Induced seismicity in geologic carbon storage

  • Vilarrasa Riaño, Víctor
  • Carrera Ramírez, Jesús
  • Olivella Pastallé, Sebastià
  • Rutqvist, Jonny
  • Laloui, Lyesse
Geologic carbon storage, as well as other geo-energy applications, such as geothermal energy, seasonal natural gas storage and subsurface energy storage imply fluid injection and/or extraction that causes changes in rock stress field and may induce (micro)seismicity. If felt, seismicity has a negative effect on public perception and may jeopardize wellbore stability and damage infrastructure. Thus, induced earthquakes should be minimized to successfully deploy geo-energies. However, numerous processes may trigger induced seismicity, which contribute to making it complex and translates into a limited forecast ability of current predictive models. We review the triggering mechanisms of induced seismicity. Specifically, we analyze (1) the impact of pore pressure evolution and the effect that properties of the injected fluid have on fracture and/or fault stability; (2) non-isothermal effects caused by the fact that the injected fluid usually reaches the injection formation at a lower temperature than that of the rock, inducing rock contraction, thermal stress reduction and stress redistribution around the cooled region; (3) local stress changes induced when low-permeability faults cross the injection formation, which may reduce their stability and eventually cause fault reactivation; (4) stress transfer caused by seismic or aseismic slip; and (5) geochemical effects, which may be especially relevant in carbonate-containing formations. We also review characterization techniques developed by the authors to reduce the uncertainty in rock properties and subsurface heterogeneity both for the screening of injection sites and for the operation of projects. Based on the review, we propose a methodology based on proper site characterization, monitoring and pressure management to minimize induced seismicity., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Multiple induced seismicity mechanisms at Castor underground gas storage illustrate the need for thorough monitoring

  • Vilarrasa, Victor
  • De Simone, Silvia
  • Carrera Ramírez, Jesús
  • Villaseñor Hidalgo, Antonio
V.V. acknowledges funding from the European Research Council (ERC) under the European Union’s Horizon 2020 Research and Innovation Programme through the Starting Grant GEoREST (www.georest.eu) under grant agreement No. 801809. A.V. acknowledges funding from Spanish Ministry of Science and Innovation grant CGL2017-88864-R. IDAEA-CSIC and ICM-CSIC are Centres of Excellence Severo Ochoa (Spanish Ministry of Science and Innovation Grants CEX2018-000794-S and CEX2019-000928-S, respectively, funded by MCIN/AEI/ 10.13039/501100011033)., Peer Reviewed, Postprint (published version)