Skip to main content

MAXIMIZACION DE LA EFICIENCIA Y MINIMIZACION DEL IMPACTO AMBIENTAL DE BOMBAS DE CALOR PARA LA DESCARBONIZACION DE LA CALEFACCION/ACS EN LOS EDIFICIOS DE CONSUMO CASI NULO

ENE2017-83665-C2-1-P

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de Fomento de la Investigación Científica y Técnica de Excelencia
Subprogram Subprograma Estatal de Generación de Conocimiento
Call Proyectos de I+D (Excelencia / Generación de Conocimiento)
Call year 2017
State Plan 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 14
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Impact of lubricant in the performance of variable speed heat pumps working with R290, Impact du lubrifiant sur les performances des pompes à chaleur à vitesse variable fonctionnant au R290

  • Ossorio-Santiago, Rubén Josep|||0000-0001-7295-7029
  • Navarro-Peris, Emilio|||0000-0002-0608-2129
  • Barta, Riley B.
[EN] Modulating the speed of the compressors and adapting its capacity to the required load has led to a decrease in the annual energy consumption in many applications. However, in the compressor, having adequate lubrication at low speeds usually implies discharging too much lubricant at higher speeds. Although necessary for compressor operation, lubricating oil acts as a contaminant in the rest of the system. Consequently, manufac- turers have to consider the oil circulation rate (OCR), as it limits the speed range of the compressor. In a previous study, a compressor was tested over its speed range (30 - 110 Hz), working with R290 and POE68 as a lubricant. Experimental data confirm the increase of OCR with speed and suggests that working with R290-POE68 could imply higher OCR values compared to other refrigerant-oil mixtures. In this study, the impact of the OCR in the performance of a R290 heat pump was theoretically assessed. Three contributions were studied: The heat transfer coefficient (HTC) reduction in the evaporator, the effect of refrigerant being solved in oil and finally, and the impact of oil in the compressor. It was found that OCR values of 5% could decrease the coefficient of performance (COP) by more than 20%., The authors would like to acknowledge the Spanish ' MINISTERIO DE ECONOMIA Y COMPETITIVIDAD' , through the project ref- ENE2017 - 83665-C2 - 1-P 'Maximización de la eficiencia y minimización del impacto ambiental de bombas de calor para la descarbonización de la calefacción/acs en los edificios de consumo casi nulo' for the given support. In addition, Ruben Ossorio would like to thank the Spanish government for his PhD scholarship with reference PRE2018 - 083535.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Improved water to water heat pump design for low-temperature waste heat recovery based on subcooling control, Conception d&apos, une pompe à chaleur eau-eau optimisée pour la récupération de chaleur perdue à basse température basée sur la régulation du sous-refroidissement

  • Hervas-Blasco, Estefania
  • Corberán, José M.
  • Navarro-Peris, Emilio|||0000-0002-0608-2129
  • Barceló Ruescas, Francisco|||0000-0002-0577-2662
[EN] Traditional heat pumps designs have been optimized for heating applications based on small secondary temperature lifts (around 5K); however, in applications with other characteristic temperature lifts, different design criteria could be required. For instance, transcritical cycles have demonstrated to have a high efficiency for domestic hot water production with high water temperature lifts. This work presents the experimental results of a new water-to-water heat pump composed by the basic heat pump components (condenser, compressor, evaporator, expansion valve and liquid reliever) able to adapt its performance depending on the required water temperature lift. Domestic hot water production from grey water waste heat recovery has been chosen as experimental application to test this heat pump. Results show COP values up to 5.5 at the design condition (20-15 degrees C at the inlet-outlet of the evaporator and 10-60 degrees C at the inlet-outlet of the condenser) and an optimal degree of subcooling of 47 K. (C) 2019 Elsevier Ltd and IIR. All rights reserved., Part of the results of this study were developed in the mainframe of the FP7 European project 'Next Generation of Heat Pumps working with Natural fluids' (NxtHPG). Part of the work presented was carried out by Estefania Hervas Blasco with the financial support of a PhD scholarship from the Spanish government SFPI1500 x 074478XV0. The authors would like also to acknowledge the Spanish 'MINISTERIO DE ECONOMIA Y COMPETITIVIDAD', through the project "MAXIMIZACION DE LA EFICIENCIA Y MINIMIZACION DEL IMPACTO AMBIENTAL DE BOMBAS DE CALOR PARA LA DESCARBONIZACION DE LA CALEFACCION/ACS EN LOS EDIFICIOS DE CONSUMO CASI NULO"with the reference ENE2017-83665-C2-1-P for the given support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Refrigerant maldistribution in brazed plate heat exchanger evaporators. Part A: Testing campaign and experimental results

  • Navarro-Peris, Emilio|||0000-0002-0608-2129
  • Álvarez-Piñeiro, Lucas|||0000-0002-9450-2479
  • Albaladejo, Paloma
  • Schnabel, Lena
  • Corberán, José M.
[EN] The refrigerant distribution in a brazed plate heat exchanger evaporator with distributor has been studied with a thermographic camera working under different conditions of inlet vapor quality, superheat, and water temperature drop. The thermographies have shown a clear uneven thermal distribution except when superheat is null. In most of the cases, they show that a great part of the liquid accumulates at the end channels of the evaporator. The degradation of the evaporator performance is higher when the water temperature drop has a similar or higher value than the superheat. On the other hand, when the superheat is significantly higher than the water temperature drop, the evaporator performance is very similar to situations in which there is an even distribution of the refrigerant. The registered evaporation temperatures are much lower for the case of 13 K of water temperature drop, highlighting the importance of the influence of this parameter on the evaporator performance. This research is described in two parts, Part A (present paper) including the description of the experimental campaign, the obtained experimental results and the results discussion and Part B including an analysis of the degradation of the evaporation temperature due to the refrigerant maldistribution as well as a deeper analysis of the registered temperatures and of the causes for the great degradation observed when the water temperature drop is increased., The authors would like to acknowledge the Spanish `Ministerio de Economia Y Competitividad', through the project "Maximizacion de la Eficiencia Y Minimizacion del Impacto Ambiental de Bombas de Calor Para la Descarbonizacion de la Calefaccion/ACS en los Edificios de Consumo Casi Nulo" with the reference ENE2017-83665C2-1-P for the given support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Comparison of the performance of a vapor-injection scroll compressor and a two-stage scroll compressor working with high pressure ratios

  • Tello-Oquendo, Fernando M.
  • Navarro-Peris, Emilio|||0000-0002-0608-2129
  • Gonzálvez-Maciá, José|||0000-0001-9422-7756
[EN] This paper presents a comparative analysis of the performance of a vapor-injection scroll compressor (SCVI) and a two-stage scroll compressor (TSSC) working with high pressure ratios in heat pump applications. Semi-empirical models of the compressors are implemented. The models are adjusted with experimental data obtained in a calorimetric test bench. The optimum displacement ratio (DR) is analyzed considering two criteria, COP maximization, and discharge temperature minimization. Once defined the optimum DR, a systematic comparison of the compressors is performed in terms of compressor efficiencies, heating capacity, COP, and discharge temperature. Finally, the intermediate pressure is optimized for a high-temperature water heating application, taking into account heat sink of finite capacity. Results show that the optimum DR of TSSC is around 0.58 and the COP is 6% larger than that the SCVI at the nominal point. Considering a wide range of operating conditions, the SCVI presents better efficiency and COP for pressure ratios below 5. For higher-pressure ratios, the TSSC presents better performance and achieves lower discharge temperature. The heating capacity of the TSSC can be improved by 7% by varying the swept volume of the high-stage compressor compared with the SCVI, with a minimum effect on the COP and on the discharge temperature from the optimum conditions., Fernando M. Tello-Oquendo acknowledges the financial support provided by the CONVOCATORIA ABIERTA 2013-SEGUNDA FASE program, which was funded by the SENESCYT (Secretaría de Educación Superior, Ciencia, Tecnología e Innovación) (Grant No. 2015-AR37665) of Ecuador. The authors would like to acknowledge Emerson Commercial and Residential Solutions for the given support to obtain the experimental data of scroll compressors and testing. In addition, the authors acknowledge the Spanish MINISTERIO DE ECONOMIA Y COMPETITIVIDAD , through the project ref-ENE2017-83665-C2-1-P Maximización de la eficiencia y minimización del impacto ambiental de bombas de calor para la descarbonización de la calefacción/ACS en los edificios de consumo casi nulo for the given support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Study of oil circulation rate in variable speed scroll compressor working with propane, Étude du débit de circulation de l&apos, huile dans un compresseur à spirales à vitesse variable fonctionnant au propane

  • Ossorio-Santiago, Rubén Josep|||0000-0001-7295-7029
  • Navarro-Peris, Emilio|||0000-0002-0608-2129
[EN] The use of hydrocarbons as refrigerants is being more common in recent years. Nevertheless, the solubility of propane in POE oils is significantly higher than in HFCs. This fact has made that POE oils used with hydrocarbons usually have a higher viscosity than the commonly used with HFCs. This approach solves the lubrication problem in the compressor but the way in which oil could affect the system performance is not so widely studied. In this work, an experimental analysis about the oil circulation rate of a variable speed compressor working with propane has been done. The study has analysed the oil circulation at different compressor speeds and evaporating temperatures. The obtained results have shown that the oil circulation rate increases with the compressor speed and reaches values higher than 5% at high speeds. This fact can penalize the COP of the system in more than 15% in these working conditions., The authors would like to acknowledge the Spanish "Ministerio De Economia Y Competitividad", through the project ref-ENE2017-83665-C2-1-P "Maximizacion de la eficiencia y minimizacion del impacto ambiental de bombas de calor para la descarbonizacion de la calefaccion/ACS en los edificios de consumo casi nulo" for the given support. In addition, Ruben Ossorio would like to thanks to the Spanish government his PhD scholarship PRE2018-083535.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Optimal design and operation of a central domestic hot water heat pump system for a group of dwellings employing low temperature waste heat as a source

  • Hervas-Blasco, Estefania
  • Corberán, José M.
  • Navarro-Peris, Emilio|||0000-0002-0608-2129
[EN] In this work, a study of an energy recovery system from a low-grade temperature source based on heat pumps for domestic hot water is done. The main components of the system are a pre-heating heat exchanger, an optimized heat pump for domestic hot water production, and a variable-volume storage tank. A model has been developed in TRNSYS to analyse the best configuration and control strategy of the system in order to satisfy the profile demands of 10, 20, and 30 multifamily houses, which are considered as a representative target market for this type of application. From this analysis, the influence of the design/sizing parameters on the system CO2 emissions has been obtained and a design criterium for their minimization has been supplied. Finally, a sensitivity analysis based on different net and heat source temperatures has been done in order to estimate the generalizability of the proposed solution. The obtained results show that this kind of system, with the proper design, sizing, and operation, offers potential CO2 emissions reductions by a factor of almost five compared to a conventional gas boiler system but a bad system selection could reduce this potential benefit up to 25%., Part of the work presented was carried out partially by Estefania Hervas Blasco with the financial support of a PhD scholarship from the Spanish government SFPI1500X074478XV0. The authors would also like to acknowledge the Spanish Ministerio de Economia y Competitividad through the project "Maximizacion de la Eficiencia y Minimizacion del Impacto Ambiental de Bombas de Calor para la Descarbonizacion de la Calefaccion/ACS en los Edificios Deconsumo Casi Nulo" with the reference ENE2017-83665-C2-1-P. Finally, this work has been also supported by the Universitat Politecnica de Valencia program ayuda a primeros Proyecto de investigacion through the project with reference SP20180039.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Semi-empirical model of scroll compressors and its extension to describe vapor-injection compressors. Model description and experimental validation, Modélisation semi-empirique de compresseurs à spirale et ses extensions pour décrire les compresseurs à injection de vapeur. Description du modèle et la validation expérimentale

  • Tello-Oquendo, Fernando
  • Navarro-Peris, Emilio|||0000-0002-0608-2129
  • Barceló Ruescas, Francisco|||0000-0002-0577-2662
  • Gonzálvez-Maciá, José|||0000-0001-9422-7756
[EN] This paper presents a semi-empirical model of scroll compressors and proposes a methodology in order to extend this model to vapor-injection scroll compressors. The model takes into account the ideal evolution of the refrigerant throughout the compressor and considers the main sources of losses in the compression process. The model is able to predict the compressor and volumetric efficiencies in terms of ten empirical parameters, which have a direct physical interpretation. For the model validation, a series of four non-injected scroll compressors of different capacities were tested using R-290 and a scroll compressor with vapor-injection (SCVI) was characterized using R-407C. Results show a correct agreement between the experimental and calculated compressor efficiencies, with a maximum deviation of ±5%. Furthermore, the model estimates accurately the discharge temperature of the refrigerant, compressor power input, and refrigerant mass flow rate in the suction and injection port. Finally, the SCVI model response was evaluated by varying the intermediate pressure and the injection superheat., Fernando M. Tello-Oquendo acknowledges the financial support provided by the CONVOCATORIA ABIERTA 2013-SEGUNDA FASE program, which was funded by the SENESCYT (Secretaría de Educación Superior, Ciencia, Tecnología e Innovación) (Grant No 2015-AR37665) of Ecuador. The authors would like to acknowledge the Spanish MINISTERIO DE ECONOMIA Y COMPETITIVIDAD , through the project ref-ENE2017-83665-C2-1-P Maximización de la eficiencia y minimización del impacto ambiental de bombas de calor para la descarbonización de la calefacción/ACS en los edificios de consumo casi nulo for the given support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Refrigerant maldistribution in brazed plate heat exchanger evaporators. Part B: Analysis of the influence of maldistribution on the evaporator performance, Mauvaise distribution du frigorigène dans les évaporateurs d&apos, échangeurs de chaleur à plaques Partie B: Analyse de l&apos, influence de la mauvaise distribution sur les performances de l&apos, évaporateur

  • Navarro-Peris, Emilio|||0000-0002-0608-2129
  • Álvarez-Piñeiro, Lucas|||0000-0002-9450-2479
  • Schnabel, Lena
  • Corberán, José M.
[EN] The maldistribution of the refrigerant mass flowrate among the different channels of a brazed plate heat exchanger evaporator with distributor, has been studied with a thermographic camera working under different conditions of inlet vapor quality, superheat, and water temperature drop. Part A of this work includes the description of the experimental campaign and a full discussion of the obtained results. This paper (part B) presents, first an evaluation of the penalty caused by the refrigerant maldistribution on the evaporator performance, and the effect of the operation conditions on that penalty; second, a data reduction methodology, which allows the quantification of the maldistribution based on a series of simple assumptions and the flow conservation equations. Finally, given that it has been found that the water temperature drop across the evaporator has a strong influence on the performance penalty due to refrigerant maldistribution, the water temperature evolution is analyzed in detailed and the reasons for its great influence are explained and commented. On this regard, it is concluded that the penalty of the maldistribution on the evaporation performance strongly depends on the availability of the secondary fluid in the channels where most of the refrigerant liquid is concentrated. The described data reduction methodology, based on the analysis of the thermographies and the measured evaporator performance, is suitable to give an estimate of the maldistribution which seems reasonable and consistent with the observed data., The authors would like to acknowledge the Spanish 'Ministerio de Economia Y Competitividad', through the project "Maximizacion de la Eficiencia Y Minimizacion del Impacto Ambiental de Bombas de Calor Para la Descarbonizacion de la Calefaccion/ACS en los Ed-ificios de Consumo Casi Nulo" with the reference ENE2017-83665-C2-1-P for the given support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Study of different subcooling control strategies in order to enhance the performance of a heat pump

  • Hervas-Blasco, Estefanía
  • Pitarch, M.
  • Corberán, José M.
  • Navarro-Peris, Emilio|||0000-0002-0608-2129
[EN] The performance of vapor-compression systems working with subcritical refrigerants varies with the degree of subcooling. There is an optimal subcooling that maximizes efficiency. However, it depends on the operating conditions and the control of the system needs to be adapted. Most of the works available in literature are able to operate in optimal conditions only at the design point or if a system is designed to be able to adapt its subcooling, only complex control algorithms that usually are difficult to set and time-costly, are used. This work focuses on the study of the main variables influencing the optimal subcooling and analyzes two different control methodologies from the theoretical point of view. Based on the theoretical study a final control strategy is selected and tested experimentally. The reliability, stability and robustness of the selected strategy are experimentally demonstrated for a wide set of operating conditions. (c) 2018 Elsevier Ltd and IIR. All rights reserved., Part of the work presented was carried by Estefania Hervas Blasco with the financial support of a PhD scholarship from the Spanish government SFPI1500 x 074478XV0. The authors would like also to acknowledge the Spanish 'MINISTERIO DE ECONOMIA Y COMPETITIVIDAD', through the project. "MAXIMIZACION DE LA EFICIENCIA Y MINIMIZACION DEL IMPACTO AMBIENTAL DE BOMBAS DE CALOR PARA LA DESCARBONIZACION DE LA CALEFACCION/ACS EN LOS EDIFICIOS DECONSUMO CASI NULO" with the reference ENE2017-83665-C2-1-P for the given support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Closing the residential energy loop: Grey-water heat recovery system for domestic hot water production based on heat pumps

  • Hervás-Blasco, Estefanía
  • Corberán, José M.
  • Navarro-Peris, Emilio|||0000-0002-0608-2129
[EN] Passive houses linked to more efficient heating and cooling technologies have been one of the focus in last years. However, to close the loop of the building sector, there is still one open source: wasted heat from grey water. This paper addresses the potentiality of the wasted heat from grey water as a heat source to produce domestic hot water (DHW) based on a heat pump system (HP). A heat pump optimized for these applications, a heat recovery heat exchanger and two variable volume storage tanks compose the system. The main objective of this work is to determine the potential recovery of the wasted heat in order to minimize the building energy consumption. Design guidelines of the components and the analysis of an optimum operation algorithm of the system have been performed in order to minimize CO2 emissions. In addition, an evaluation of the potential heat recovery of the wasted heat is included. As an example, that methodology has been applied to 20 dwellings. Based on that case, the obtained results demonstrate that by recovering 80% of the available recovery heat, the total demand of DHW is satisfied with high levels of comfort and efficiency., Part of the work presented was carried out by Estefania Hervas Blasco with the financial support of a PhD scholarship from the Spanish government SFPI1500 x074478XV0. The authors would like also to acknowledge the Spanish `Ministerio de Economia Y Competitividad', through the project "Maximizacion de la Eficiencia Y Minimizacion del Impacto Ambiental de Bombas de Calor Para la Descarbonizacion de la Calefaccion/ACS EN Los Edificios de Consumo Casi Nulo" with the reference ENE2017-83665-C2-1-P for the given support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Exergy analysis on a heat pump working between a heat sink and a heat source of finite heat capacity rate

  • Pitarch, Miguel
  • Hervás-Blasco, Estefanía
  • Corberán, José M.
  • Navarro-Peris, Emilio|||0000-0002-0608-2129
[EN] The optimum performance of a pure subcritical refrigeration cycle depends significantly on the temperature lift of the heat source and sink. Therefore, the maximization of the system efficiency has to be linked to them. This paper shows an exergy analysis of each heat pump component (condenser, evaporator, expansion valve and compressor) considering that the heat source and sink are not at constant temperature. The performed study shows the components with more possibilities for improvement. Based on this analysis, the optimization of cycle parameters like subcooling and superheat as a function of the external conditions have been done. In addition, this work has demonstrated that the components having a higher influence in the system irreversibility's depends significantly on the temperature lift of the secondary fluids. Finally, the obtained results show potentials improvements of the efficiency up to 23% if the system is able to operate in the optimal subcooling and superheat., Part of the results of this study were developed in the mainframe of the FP7 European project 'Next Generation of Heat Pumps workingwith natural fluids' (NxtHPG). Part of the work presented was carried by Miquel Pitarch with the financial support of a PhD scholarship from the Universitat Politecnica de Valencia. Part of the work presented was carried by Estefania Hervas-Blasco with the financial support of a Ph.D. scholarship from the Spanish government SFPI1500X074478XV. The authors would like also to acknowledge the Spanish 'MINISTERIO DE ECONOMIA Y COMPETITIVIDAD', through the Project ENE2017-83665-C2-1-P, "Maximizacion de la Eficiencia y Minimizacion del Impacto Ambiental de Bombas de Calor para la descarbonizacion de la calefaccion/ACS en los proximos edificios de consumo energetico casi nulo" for the given support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Testing of Variable-Speed Scroll Compressors and their inverters for the evaluation of compact energy consumption models

  • Ossorio-Santiago, Rubén Josep|||0000-0001-7295-7029
  • Navarro-Peris, Emilio|||0000-0002-0608-2129
[EN] Prediction models for energy consumption in heat pumps are critical for design, selection, control and fault detection. However, nowadays, the methodology for characterizing variable-speed compressors has not been standardized, and typically the pair compressor-inverter is studied as a whole. In this study, disaggregated energy consumption results of compressor and inverter are provided by using a double-wattmeter scheme. These results are used to compare the performance of existing models and to establish guidelines to define testsmatrixes as compact as possible to characterize this type of compressors. The widely used 20-coefficient correlation can overfit the compressor behaviour when fitted with an small dataset, introducing significant deviations when extrapolating. Optimal Design methodologies to create rating test matrixes gave excellent results compared with classical clustering techniques. Regarding inverter results, a compact empirical model was proposed to model inverter power losses depending on total consumption and compressor speed. The proposed model used only five fitting coefficients, and most predictions are inside a 5% error band for all tested inverters. Finally, the tested compressors and inverters suffered a significant efficiency loss at very low speeds, which could make cycling more profitable under certain circumstances., The authors would like to acknowledge the Spanish "MINISTERIO DE ECONOMIA Y COMPETITIVIDAD", through the project ref-ENE2017-83665-C2-1-P "Maximizacion de la eficiencia y minimizacion del impacto ambiental de bombas de calor para la descarbonizacion de la calefaccion/acs en los edificios de consumo casi nulo" for the given support. In addition, Ruben Ossorio would like to thank the Spanish government for his PhD scholarship with reference PRE2018-083535.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Thermodynamic assessment of ultra-low-global warming potential refrigerants for space and water heaters

  • Sánchez-Moreno-Giner, Luis
  • López-Juárez, Emilio
  • Gonzálvez-Maciá, José|||0000-0001-9422-7756
  • Hassan, Abdelrahman|||0000-0001-9063-9569
[EN] The current paper studies the most suitable ultra-low-global warming potential (GWP) (GWP < 30) candidates in the market, considering also its grade of flammability and toxicity, for heat pumps employed for different space heating and domestic hot water (DHW) applications. A pre-design thermodynamic model has been developed to evaluate the performance and size limits for any subcritical or transcritical heat pump under certain working conditions. This generic model is based on the pinch point approach, so it does not depend on a certain type of heat exchangers, it only depends on the external working conditions. The results showed that all subcritical ultra-low-GWP, nonflammable, and nontoxic refrigerants considered have either lower coefficient of performance (COP) or volumetric heating capacity (VHC) compared with the reference high-GWP refrigerants R-410A and R-134a. Additionally, the only refrigerants with higher COP, such as R-717 (ammonia) or R-290 (propane), are either extremely flammable or toxic. For the applications need of high water-side temperature lift, the transcritical refrigerants R-744 (CO2) and R-170 (ethane) showed the best performance, regarding both COP and VHC values, of all the refrigerants studied. The refrigerants R-161, R-1270 (propylene), and R-1234yf presented a balanced performance in both space heating and DHW applications. This makes them potential candidates to be employed in subcritical multi-temperature levels heat pumps., This work was partially supported by the Research and Development Aid Program (PAID-01-17) of the Universitat Politecnica de Valencia for receiving the Research Fellowship FPI-UPV-2017. The authors also would like to acknowledge the financial support provided by the Ministerio de Ciencia, Innovacion y Universidades de Espana for the project "Maximizacion de la eficiencia y minimizacion del impacto ambiental de bombas de calor para la descarbonizacion de la calefaccion/acs en los edificios de consumo casi nulo" (ENE2017-83665-C2-1-P).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Energy and techno-economic assessment of the effect of the coupling between an air source heat pump and the storage tank for sanitary hot water production

  • Masip, X.
  • Corberán, José M.
  • Cazorla-Marín, Antonio|||0000-0003-3314-0395
  • Montagud- Montalvá, Carla|||0000-0002-7118-6119
  • Marchante-Avellaneda, Javier|||0000-0001-5680-5033
  • Barceló Ruescas, Francisco|||0000-0002-0577-2662
[EN] Heat pumps are proved to be a highly efficient technology for sanitary hot water production. However, when installing them coupled with the storage tank, an inefficiency up to 30% can be introduced in the system since this coupling cannot be direct according to EN 1717:2000; in order to prevent from any potential pollution of potable water in case of a refrigerant leakage. This research work evaluates three types of indirect coupling in the case of an air source heat pump system for sanitary hot water production: a coil heat exchanger inside the storage tank (CC), an intermediate heat exchanger between the tank and the heat pump (EHXC) and a double wall condenser (DWCC). A techno-economic assessment was carried out for the representative climate conditions around Europe. Results show that the DWCC is always the most efficient and cost-effective solution with a 3.66% lower energy efficiency than the direct coupling (Base Case), whereas the CC is not only the less efficient solution (27.1% lower than the Base Case) but also the less cost-effective, with a 50% lower net present value than the DWCC., The authors acknowledge the financial support provided by the project "ENE2017-83665-C2-1-P" and the programme 'Formation de Profesorado Universitario (FPU15/03476)', funded by the "Ministerio de Ciencia, Innovation y Universidades" of Spain.