Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Tailoring sintering properties of BaGd 0.3 La 0.7 Co 2 O 6-s steam electrodes for pressurized tubular proton-ceramic electrolysis cells

  • Navarrete Algaba, Laura
  • Tarach, Mateusz
  • Vollestad, Einar
  • Mahmood, Asif
  • Catalán-Martínez, David
  • Fontaine, Marie-Laure
  • Norby, Truls
  • Almar-Liante, Laura|||0000-0001-5103-3812
  • Escolástico Rozalén, Sonia|||0000-0002-7097-2425
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] We herein address manufacturing constraints related to the high-temperature sintering step required for reaching adequate adhesion of oxygen/steam electrodes on proton ceramic electrolytes, particularly in tubular geometry. Incorporating various sintering aids such as Cu, Co, and Ni oxides improves the sinterability of the electrodes and reduces the sintering temperature to 950 degrees C. The ceramic-ceramic composite electrodes based on BaGd 0.3 La 0.7 Co 2 O 6-s (BGLC37) and BaZr 0.7 Ce 0.2 Y 0.1 O 6-s (BZCY) show good and robust electrode-electrolyte adhesion. Composite electrodes were tested under different operation conditions, i.e., temperatures and oxygen partial pressures in symmetrical cell configuration, achieving apparent polarisation resistances below 0.6 Omega & sdot; cm 2 at 600 degrees C in wet air for all the electrodes with sintering aids. Finally, BGLC37/BZCY with 2 wt% of CuO electrodes were successfully applied on pre-reduced and sealed BZCY/Ni-supported tubular half-cells with 16 cm2 active area and measured in electrolysis mode at 600 degrees C and high steam pressure. The results open a route to manufacturing steam electrodes for large-scale electrolysis cells., This work is part of the GAMER and WINNER projects that have received funding from the Fuel Cell and Hydrogen 2 Joint Undertaking under Grant Agreement No 779486 and No 101007165. This Joint Undertaking receives support from the European Union's Horizon 2020 Research and Innovation programme, Hydrogen Europe and Hydrogen Europe Research.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Redox-Stable Electrodes for Ethane Dehydrogenation Based on Proton Ceramic Electrochemical Reactors

  • Barrio-Querol, Elena
  • Catalán-Martínez, David
  • Leonard, Kwati
  • Almar-Liante, Laura|||0000-0001-5103-3812
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
  • Escolástico Rozalén, Sonia|||0000-0002-7097-2425
[EN] Ethylene is one of the most widely used components in the chemical industry, but the main manufacturing route involves significant energy consumption and generates substantial CO2 emissions. Proton ceramic electrochemical reactors (PCERs) offer great potential for process intensification and could play a key role in ethane dehydrogenation (EDH) by extracting H-2 produced during the reaction. This process not only improves the reaction yield but also enables the production of a pure separated H-2 stream. However, nonoxidative EDH reaction conditions lead to coke formation, which is further increased by H-2 extraction, resulting in a decrease in system performance. Therefore, to successfully integrate PCER technology into ethylene production, it is crucial to develop stable redox electrodes that can withstand both nonoxidative H-2 extraction and coke oxidation conditions. In this work, we study different composite electrodes based on the perovskite La0.8Sr0.2Cr0.5Mn0.5O3-delta (LSCM) combined with the proton conductor BaCe0.55Zr0.3Y0.15O3-delta (BCZY(5515)). The electrochemical performance was characterized by using electrochemical impedance spectroscopy under both oxidizing and reducing conditions. The data analysis indicates that surface processes limit electrode operation. The infiltration of Pt and CeO2 nanoparticles in the electrode enhanced the electrochemical performance, improving it by a factor of 10 at 700 degrees C. The optimal electrochemical performance was observed for the LSCMF/BCZY(5515) (La0.8Sr0.2Cr0.5Mn0.25Fe0.25O3-delta/BaCe0.55Zr0.3Y0.15O3-delta) electrode infiltrated with Pt/CeO2, demonstrating promising properties as a redox-stable electrode. Finally, we evaluated the nonoxidative EDH reaction using a PCER based on a Ni-SrZr0.5Ce0.4Y0.1O2.95 (SZCY541) supported cell with a LSCMF/BCZY(5515) anode infiltrated with Pt/CeO2 and a thin BaZr0.44Ce0.36Y0.2O3-delta electrolyte., This work is part of the WINNER project that has received funding from the Fuel Cell and Hydrogen 2 Joint Undertaking under grant agreement no 101007165. This Joint Undertaking received support from the European Union's Horizon 2020 Research and Innovation programme, Hydrogen Europe and Hydrogen Europe Research. Financial support by the Spanish Ministry of Science and Innovation (PID2022-139663OB-100 and CEX2021-001230-S grants funded by MCIN/AEI/10.13039/501100011033) and by the Generalitat Valenciana (CIACIF/2021/199 and CIPROM/2022/10 grants) is gratefully acknowledged. Also, the authors acknowledge the support of the Servicio de Microscopia Electronica of the Universitat Politecnica de Valencia (UPV).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Redox-stable composite electrodes for CH4 conversion reactors based on proton ceramic electrochemical cells

  • Almar-Liante, Laura|||0000-0001-5103-3812
  • Fabuel Robledo, Maria
  • Escolástico Rozalén, Sonia|||0000-0002-7097-2425
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
  • Bausá, N.
[EN] Electrochemical reactors based on proton-conducting ceramic electrolytes show a great potential in the conversion of hydrocarbons by enabling the intensification via the in-situ extraction of the H-2 produced. However, non-oxidative operation conditions lead to the progressive coke formation on the catalyst and electrodes and thus, an oxidative regeneration cycle is required to restore the catalyst activity. Consequently, newly redox-stable electrodes are required to enable operation under both non-oxidative H-2-extraction and coke-oxidation conditions. Here, four composite materials were investigated as redox-stable electrode backbones for their integration in proton-conducting cells, composed by the proton conductor BaCe0.2Zr0.7Y0.1O3-delta (BCZY27) and La0.85Sr0.15FeO3 (LSF8515), La0.5Sr0.5FeO3 (LSF55), La0.84Sr0.16Cr0.5Mn0.5O3 (LSCM) or La0.8Sr0.2MnO3 (LSM). Chemical compatibility with the electrolyte and electrochemical performance were characterized in the range 500-800 ?C. LSCM/BCZY27 and LSM/BCZY27 showed the best performance. The electrode activity was boosted by catalytically activating with Pt and CeO2 nanoparticles while exhibiting outstanding stability upon redox cycling. LSM/BCZY27+Pt/CeO2 showed the lowest polarization resistance, i.e., achieving 0.7 omega cm(2 )at 700 ?C in 10% CH4 and 9% H-2 and 0.14 omega cm(2) in air, revealing a high potential as redox-stable electrode for non-oxidative hydrocarbon conversion in electrochemical reactors., Part of the present research was developed in the frame of N. Bausa's PhD thesis (Chapter 9) that has received funding from Spanish Government (RTI2018-102161 grant). This work has been also supported by the WINNER project. This project has received funding from the Fuel Cells and Hydrogen 2 Joint Undertaking (now Clean Hydrogen Partnership) under Grant Agreement No 101007165. This Joint Undertaking receives support from the European Union's Horizon 2020 Research and Innovation program, Hydrogen Europe and Hydrogen Europe Research.