Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Tailoring sintering properties of BaGd 0.3 La 0.7 Co 2 O 6-s steam electrodes for pressurized tubular proton-ceramic electrolysis cells

  • Navarrete Algaba, Laura
  • Tarach, Mateusz
  • Vollestad, Einar
  • Mahmood, Asif
  • Catalán-Martínez, David
  • Fontaine, Marie-Laure
  • Norby, Truls
  • Almar-Liante, Laura|||0000-0001-5103-3812
  • Escolástico Rozalén, Sonia|||0000-0002-7097-2425
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] We herein address manufacturing constraints related to the high-temperature sintering step required for reaching adequate adhesion of oxygen/steam electrodes on proton ceramic electrolytes, particularly in tubular geometry. Incorporating various sintering aids such as Cu, Co, and Ni oxides improves the sinterability of the electrodes and reduces the sintering temperature to 950 degrees C. The ceramic-ceramic composite electrodes based on BaGd 0.3 La 0.7 Co 2 O 6-s (BGLC37) and BaZr 0.7 Ce 0.2 Y 0.1 O 6-s (BZCY) show good and robust electrode-electrolyte adhesion. Composite electrodes were tested under different operation conditions, i.e., temperatures and oxygen partial pressures in symmetrical cell configuration, achieving apparent polarisation resistances below 0.6 Omega & sdot; cm 2 at 600 degrees C in wet air for all the electrodes with sintering aids. Finally, BGLC37/BZCY with 2 wt% of CuO electrodes were successfully applied on pre-reduced and sealed BZCY/Ni-supported tubular half-cells with 16 cm2 active area and measured in electrolysis mode at 600 degrees C and high steam pressure. The results open a route to manufacturing steam electrodes for large-scale electrolysis cells., This work is part of the GAMER and WINNER projects that have received funding from the Fuel Cell and Hydrogen 2 Joint Undertaking under Grant Agreement No 779486 and No 101007165. This Joint Undertaking receives support from the European Union's Horizon 2020 Research and Innovation programme, Hydrogen Europe and Hydrogen Europe Research.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Thermo-fluid dynamics modelling of steam electrolysis in fully-assembled tubular high-temperature proton-conducting cells

  • Catalán-Martínez, David
  • Navarrete Algaba, Laura
  • Tarach, Mateusz
  • Vøllestad, E.
  • Norby, T.
  • Budd, M.I.
  • Veenstra, P.
  • Santos-Blasco, Joaquín
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] Electrolysis based on renewable energies offers a promising carbon-free solution for hydrogen generation and storage. The recent developments of proton ceramic electrolysis cells operating at intermediate temperatures bear promise of superior energy efficiency compared to oxide ion conducting electrolytes. Here, a proton ceramic Single Engineering Unit (SEU) design is optimized for steam electrolysis using a computational fluid dynamics (CFD) model implemented in a COMSOL Multiphysics software. The SEU is an all-in-one tubular cell arrangement that constitutes the smallest electrolysis unit and enables efficient, adaptable pressurized hydrogen generation. The parametrical modelling study is conducted for two adiabatic operation scenarios with distinct steam conversion rates and tested for multiple key parameters, namely internal and external chamber pressures and inlet stream temperature. The modelling results show that low steam conversions enable operation at higher current densities and that the thermoneutral voltage for a fixed steam conversion is highly sensitive to the process conditions and operation modes. The increment of the pressure of the generated hydrogen implies a reduced production rate at thermoneutral voltage, although it can be compensated with an enhanced steam pressure or a reduced inlet temperature. Additionally, the introduction of a porous medium as the SEU current collector in the steam chamber enhances heat transport within this chamber. The area specific resistance of the system determines the current density, enforcing an adaption of the area of the electrolyser to satisfy the target hydrogen production and energy efficiency. The resulting proposed SEU design and adapted operational parameters allow effective delivery of pressurized dry hydrogen for a wide range of conditions and applications, The work leading to these results has received funding from Spanish Government (RTI2018-102161 grant) and from Fuel Cells and Hydrogen 2 Joint Undertaking under grant agreement 779486 (`GAMER'). This Joint Undertaking receives support from the European Union's Horizon 2020 research and innovation programme, Hydrogen Europe and Hydrogen Europe research.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Mixed proton and electron conducting double perovskite anodes for stable and efficient tubular proton ceramic electrolysers.

  • Vøllestad, Einar
  • Strandbakke, Ragnar
  • Tarach, Mateusz
  • Catalán-Martínez, David
  • Fontaine, Marie-Laure
  • Beeaff, Dustin
  • Clark, Daniel R.
  • Norby, Truls
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] Hydrogen production from water electrolysis is a key enabling energy storage technology for the large-scale deployment of intermittent renewable energy sources. Proton ceramic electrolysers (PCEs) can produce dry pressurized hydrogen directly from steam, avoiding major parts of cost-driving downstream separation and compression. However, the development of PCEs has suffered from limited electrical efficiency due to electronic leakage and poor electrode kinetics. Here, we present the first fully operational BaZrO3-based tubular PCE, with 10 cm(2) active area and a hydrogen production rate above 15 Nml min(-1). The novel steam anode Ba1-xGd0.8La0.2+xCo2O6-delta exhibits mixed p-type electronic and protonic conduction and low activation energy for water splitting, enabling total polarization resistances below 1 Omega cm(2) at 600 degrees C and Faradaic efficiencies close to 100% at high steam pressures. These tubular PCEs are mechanically robust, tolerate high pressures, allow improved process integration and offer scale-up modularity., The work leading to these results has received funding from the Research Council of Norway (grant 236828) and from the European Union's Seventh Framework Programme (FP7/2007-2013) for the Fuel Cells and Hydrogen Joint Technology Initiative under grant agreement 621244 ('ELECTRA') and Fuel Cells and Hydrogen 2 Joint Undertaking under grant agreement 779486 ('GAMER'). This Joint Undertaking receives support from the European Union's Horizon 2020 research and innovation programme, Hydrogen Europe and Hydrogen Europe research.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Mixed proton and electron conducting double perovskite anodes for stable and efficient tubular proton ceramic electrolysers

  • Vøllestad, Einar
  • Strandbakke, Ragnar
  • Tarach, M.
  • Catalán-Martínez, David
  • Fontaine, Marie-Laure
  • Beeaff, Dustin
  • Clark, Daniel R.
  • Serra Alfaro, José Manuel
  • Norby, Truls
Hydrogen production from water electrolysis is a key enabling energy storage technology for the large-scale deployment of intermittent renewable energy sources. Proton ceramic electrolysers (PCEs) can produce dry pressurized hydrogen directly from steam, avoiding major parts of cost-driving downstream separation and compression. However, the development of PCEs has suffered from limited electrical efficiency due to electronic leakage and poor electrode kinetics. Here, we present the first fully operational BaZrO3-based tubular PCE, with 10 cm2 active area and a hydrogen production rate above 15 Nml min¿1. The novel steam anode Ba1¿xGd0.8La0.2+xCo2O6¿¿ exhibits mixed p-type electronic and protonic conduction and low activation energy for water splitting, enabling total polarization resistances below 1 ¿ cm2 at 600 °C and Faradaic efficiencies close to 100% at high steam pressures. These tubular PCEs are mechanically robust, tolerate high pressures, allow improved process integration and offer scale-up modularity., The work leading to these results has received funding from the Research Council of Norway (grant 236828) and from the European Union’s Seventh Framework Programme (FP7/2007-2013) for the Fuel Cells and Hydrogen Joint Technology Initiative under grant agreement 621244 (‘ELECTRA’) and Fuel Cells and Hydrogen 2 Joint Undertaking under grant agreement 779486 (‘GAMER’). This Joint Undertaking receives support from the European Union’s Horizon 2020 research and innovation programme, Hydrogen Europe and Hydrogen Europe research.