Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Robust catalytically-activated LSM-BCZY-based composite steam electrodes for proton ceramic electrolysis cells

  • Bausá, Nuria
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] Backbone electrodes based on an electronic conductor and a protonic conductor show advantages for proton ceramic electrolyzer cells (PCECs). This work, aims to shed further light on the nature of the rate determining steps in the anode operation and improve the reaction rate in high steam pressure electrolysis mode by (i) adjusting their catalytic activity through electrode infiltration with catalytic electronic-conducting nanoparticles; and (ii) electrochemical activation of surface species by applying a net current through the electrode. A composite formed by La0.8Sr0.2MnO3-delta (LSM) and BaCe0.2Zr0.7Y0.1O3-delta (BCZY27) was deposited on proton-conducting BCZY27 electrolytes and studied in symmetrical cells to investigate the anode microstructure and electrochemical performance. Electrochemical impedance spectroscopy (EIS) measurements were performed in the 800-500 degrees C range under 3 bar of pressure of wet air (75% of steam). LSM/BCZY27 50/50 vol% showed the best performance with an electrode polarization resistance (R-p) of 6.04 omega cm(2) at 700 degrees C and high steam pressure (0.75 bar of air and 2.25 bar of steam) whereas LSM/BCZY27 60/40 vol% presented a R-p of 18.9 omega cm(2). The backbone electrodes were infiltrated using aqueous solutions of metal precursors to boost the electrocatalytic activity towards water splitting and oxygen evolution. The infiltrated cells were fired at 850 degrees C for 2 h to obtain the desired crystalline nanoparticles (Pr6O11, CeO2, ZrO2 and Pr6O11-CeO2) and electrochemically tested under high steam pressures and bias currents to investigate the influence of catalytic activation on surface exchange kinetics. Among the tested catalysts, the lowest electrode polarization resistances (<0.2 omega cm(2)) were reached for the Pr6O11, CeO2 and Pr6O11-CeO2 catalysts at 700 degrees C by applying current densities ranging from 1.57 to 14.15 mA cm(-2), and the Pr6O11-CeO2-activated LSM/BCZY27 electrode exhibited the best performance. Finally, the effect of pO(2) and pH(2)O was investigated aiming to characterize the rate limiting processes in the electrodes., Financial support by the Spanish Government (Grants SEV-2016-0683, RTI2018-102161 and ENE2014-57651), Generalitat Valenciana (PROMETEO/2018/006) and by the EU through FP7 Electra Project (Grant Agreement 621244) is gratefully acknowledged. The support of the microscopy service at Universitat Politecnica de Valencia (UPV) for the SEM analysis is recognized.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Catalytic Surface Promotion of Composite Cathodes in Protonic Ceramic Fuel Cells

  • Solis Díaz, Cecilia
  • Navarrete Algaba, Laura
  • Bozza, Francesco
  • Bonanos, Nikolaos
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] Composite cathodes based on an electronic conductor and a protonic conductor show advantages for protonic ceramic fuel cells. In this work, the performance of a La5.5WO11.25-delta/La0.8Sr0.2MnO3+delta (LWO/LSM) composite cathode in a fuel cell based on an LWO protonic conducting electrolyte is shown and catalytically improved. The limiting processes were first unambiguously associated to surface steps, and the reaction rate was significantly enhanced by 1) tailoring the catalytic activity through electrode surface impregnation with intrinsically catalytic nanoparticles and 2) electrochemical activation of surface species by imposing a net current through the electrode., Funding from the European Union (FP7 Project EFFIPROGrant Agreement 227560 and FP7 Project ELECTRAGrant Agreement 621244) and the Spanish Government (ENE2011-24761 and SEV-2012-0267) is kindly acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Direct CO2 conversion to syngas in a BaCe0.2Zr0.7Y0.1O3- delta-based proton-conducting electrolysis cell

  • Bausá-Martínez, Nuria
  • Escolástico Rozalén, Sonia|||0000-0002-7097-2425
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] Electrolysis of steam and CO2 is considered to be a promising instrument for energy storage via sustainable H-2 and hydrocarbon production. A model electrolysis cell was assembled using a thick BaCe0.2Zr0.7Y0.1O3-delta (BCZY27) electrolyte and two distinct electrodes, i.e., a (H-2-cathode) porous Pt layer; and (steam-anode) a composite made of 60 vol. % La0.8Sr0.2MnO3-delta (LSM) and 40 vol. % BCZY27. The as-sintered steam electrode was catalytically-activated with Pr6O11-CeO2 nanoparticles. The cell was characterized by means of voltamperometry and impedance spectroscopy. Different operation parameters were analyzed: temperature; water concentration in the anode chamber; and H-2 and CO2 concentration in the cathode chamber. Increasing H2O concentration (in the anode) and presence of CO2 (in the cathode) positively affected the electrode performance giving rise to lower cell overpotential and, consequently, substantial improvement in Faradaic efficiency. The high electrolyte thickness and the non-optimized Pt cathode limited the range of current density and the achieved peak power densities. The Faradaic efficiency for water electrolysis reached a value of 39% at 10.4 mA/cm(2), as determined by the analysis of the H-2 production. During co-electrolysis, the CO2 reaction was fostered by co-feeding a minimum H-2 amount. CO formation took place through the reverse water gas shift (RWGS) reaction. When the current density was applied, CO2 conversion increased due mainly to the non-Faradaic electrochemical modification of catalytic activity (NEMCA effect) that allowed for the improvement of CO2 hydrogenation kinetics., Financial support by the Spanish Government (SEV-2016-0683, Project ENE2014-57651 and IJCI-2016-28330 grants) and by the EU through FP7 Electra Project (Grant Agreement 621244) is gratefully acknowledged. The support of the microscopy service at Universitat Politecnica de Valencia (UPV) for the SEM analysis is recognized.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Mixed proton and electron conducting double perovskite anodes for stable and efficient tubular proton ceramic electrolysers.

  • Vøllestad, Einar
  • Strandbakke, Ragnar
  • Tarach, Mateusz
  • Catalán-Martínez, David
  • Fontaine, Marie-Laure
  • Beeaff, Dustin
  • Clark, Daniel R.
  • Norby, Truls
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] Hydrogen production from water electrolysis is a key enabling energy storage technology for the large-scale deployment of intermittent renewable energy sources. Proton ceramic electrolysers (PCEs) can produce dry pressurized hydrogen directly from steam, avoiding major parts of cost-driving downstream separation and compression. However, the development of PCEs has suffered from limited electrical efficiency due to electronic leakage and poor electrode kinetics. Here, we present the first fully operational BaZrO3-based tubular PCE, with 10 cm(2) active area and a hydrogen production rate above 15 Nml min(-1). The novel steam anode Ba1-xGd0.8La0.2+xCo2O6-delta exhibits mixed p-type electronic and protonic conduction and low activation energy for water splitting, enabling total polarization resistances below 1 Omega cm(2) at 600 degrees C and Faradaic efficiencies close to 100% at high steam pressures. These tubular PCEs are mechanically robust, tolerate high pressures, allow improved process integration and offer scale-up modularity., The work leading to these results has received funding from the Research Council of Norway (grant 236828) and from the European Union's Seventh Framework Programme (FP7/2007-2013) for the Fuel Cells and Hydrogen Joint Technology Initiative under grant agreement 621244 ('ELECTRA') and Fuel Cells and Hydrogen 2 Joint Undertaking under grant agreement 779486 ('GAMER'). This Joint Undertaking receives support from the European Union's Horizon 2020 research and innovation programme, Hydrogen Europe and Hydrogen Europe research.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Robust catalytically-activated LSM-BCZY-based composite steam electrodes for proton ceramic electrolysis cells

  • Bausá, Nuria
  • Serra Alfaro, José Manuel
Backbone electrodes based on an electronic conductor and a protonic conductor show advantages for proton ceramic electrolyzer cells (PCECs). This work, aims to shed further light on the nature of the rate determining steps in the anode operation and improve the reaction rate in high steam pressure electrolysis mode by (i) adjusting their catalytic activity through electrode infiltration with catalytic electronic-conducting nanoparticles; and (ii) electrochemical activation of surface species by applying a net current through the electrode., Financial support by the Spanish Government (Grants SEV-2016-0683, RTI2018-102161 and ENE2014-57651), Generalitat Valenciana (PROMETEO/2018/006) and by the EU through FP7 Electra Project (Grant Agreement 621244) is gratefully acknowledged. The support of the microscopy service at Universitat Politècnica de València (UPV) for the SEM analysis is recognized.