Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Microbial electrosynthesis of acetate from CO2 in three-chamber cells with gas diffusion biocathode under moderate saline conditions

  • Dessì, Paolo
  • Buenaño Vargas, Claribel
  • Martínez Sosa, Santiago
  • Mills, Simon
  • Trego, Anna
  • Ijaz, Umer Z.
  • Pant, Deepak
  • Puig Broch, Sebastià
  • O'Flaherty, Vincent
  • Farràs, Pau
The industrial adoption of microbial electrosynthesis (MES) is hindered by high overpotentials deriving from low electrolyte conductivity and inefficient cell designs. In this study, a mixed microbial consortium originating from an anaerobic digester operated under saline conditions (∼13 g L−1 NaCl) was adapted for acetate production from bicarbonate in galvanostatic (0.25 mA cm−2) H-type cells at 5, 10, 15, or 20 g L−1 NaCl concentration. The acetogenic communities were successfully enriched only at 5 and 10 g L−1 NaCl, revealing an inhibitory threshold of about 6 g L−1 Na+. The enriched planktonic communities were then used as inoculum for 3D printed, three-chamber cells equipped with a gas diffusion biocathode. The cells were fed with CO2 gas and operated galvanostatically (0.25 or 1.00 mA cm−2). The highest production rate of 55.4 g m−2 d−1 (0.89 g L−1 d−1), with 82.4% Coulombic efficiency, was obtained at 5 g L−1 NaCl concentration and 1 mA cm−2 applied current, achieving an average acetate production of 44.7 kg MWh−1. Scanning electron microscopy and 16S rRNA sequencing analysis confirmed the formation of a cathodic biofilm dominated by Acetobacterium sp. Finally, three 3D printed cells were hydraulically connected in series to simulate an MES stack, achieving three-fold production rates than with the single cell at 0.25 mA cm−2. This confirms that three-chamber MES cells are an efficient and scalable technology for CO2 bio-electro recycling to acetate and that moderate saline conditions (5 g L−1 NaCl) can help reduce their power demand while preserving the activity of acetogens, This work was performed on the framework of the Science Foundation Ireland (SFI) Pathfinder Award on “Hybrid Bio-Solar Reactors for wastewater treatment and CO2 recycling” (award nr. 19/FIP/ZE/7572 PF). PD is supported by the European Union's Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement, project ATMESPHERE, No 101029266. SP is a Serra Hunter Fellow (UdG-AG-575) and acknowledges the funding from the ICREA Academia award. LEQUIA has been recognised as a consolidated research group by the Catalan Government (2021-SGR-01352). UZI is supported by EPSRC (EP/P029329/1 and EP/V030515/1). VOF is supported by the Enterprise Ireland Technology Centres Programme (TC/2014/0016) and Science Foundation Ireland (14/IA/2371, 19/FFP/6746 and 16/RC/3889). DP acknowledges the support of the VIVALDI project that has received funding from the European Union's Horizon 2020 research and innovation program under grant agreement 101000441
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Selective butyric acid production from CO2 and its upgrade to butanol in microbial electrosynthesis cells

  • Romans Casas, Meritxell
  • Feliu Paradeda, Laura
  • Tedesco, Michele
  • Hamelers, Hubertus M.V
  • Bañeras Vives, Lluís
  • Balaguer i Condom, Maria Dolors
  • Puig Broch, Sebastià
  • Dessì, Paolo
Microbial electrosynthesis (MES) is a promising carbon utilization technology, but the low-value products (i.e., acetate or methane) and the high electric power demand hinder its industrial adoption. In this study, electrically efficient MES cells with a low ohmic resistance of 15.7 mΩ m2 were operated galvanostatically in fed-batch mode, alternating periods of high CO2 and H2 availability. This promoted acetic acid and ethanol production, ultimately triggering selective (78% on a carbon basis) butyric acid production via chain elongation. An average production rate of 14.5 g m−2 d−1 was obtained at an applied current of 1.0 or 1.5 mA cm−2, being Megasphaera sp. the key chain elongating player. Inoculating a second cell with the catholyte containing the enriched community resulted in butyric acid production at the same rate as the previous cell, but the lag phase was reduced by 82%. Furthermore, interrupting the CO2 feeding and setting a constant pH2 of 1.7–1.8 atm in the cathode compartment triggered solventogenic butanol production at a pH below 4.8. The efficient cell design resulted in average cell voltages of 2.6–2.8 V and a remarkably low electric energy requirement of 34.6 kWhel kg−1 of butyric acid produced, despite coulombic efficiencies being restricted to 45% due to the cross-over of O2 and H2 through the membrane. In conclusion, this study revealed the optimal operating conditions to achieve energy-efficient butyric acid production from CO2 and suggested a strategy to further upgrade it to valuable butanol, This research was carried out in the project “PANGEA – Process intensificAtioN for bioelectroCO2 recyclinG into carbon-nEutrAl products) funded by the Spanish Ministry of Innovation and Science (ref. PID2021-126240OB-I00). PD is supported by the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement, project ATMESPHERE, No 101029266. MR-C is grateful for the support of the Spanish Government (FPU20/01362). S.P. is a Serra Hunter Fellow (UdG-AG-575) and acknowledges the funding from the ICREA Academia award. LF-P is grateful for the Research Training grant from the Catalan Government (2021 FISDU 00132). LEQUIA and EcoAqua have been recognized by the Catalan Government (Ref 2021 SGR01352 and 2021 SGR01142), Open Access funding provided thanks to the CRUE-CSIC agreement with Elsevier
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

CO2 in indoor environments: From environmental and health risk to potential renewable carbon source

  • López de León, Luis R.
  • Dessì, Paolo
  • Cabrera-Codony, Alba
  • Rocha-Melogno, Lucas
  • Kraakman, Bart
  • Naddeo, Vincenzo
  • Balaguer i Condom, Maria Dolors
  • Puig Broch, Sebastià
In the developed world, individuals spend most of their time indoors. Poor Indoor Air Quality (IAQ) has a wide range of effects on human health. The burden of disease associated with indoor air accounts for millions of premature deaths related to exposure to Indoor Air Pollutants (IAPs). Among them, CO2 is the most common one, and is commonly used as a metric of IAQ. Indoor CO2 concentrations can be significantly higher than outdoors due to human metabolism and activities. Even in presence of ventilation, controlling the CO2 concentration below the Indoor Air Guideline Values (IAGVs) is a challenge, and many indoor environments including schools, offices and transportation exceed the recommended value of 1000 ppmv. This is often accompanied by high concentration of other pollutants, including bio-effluents such as viruses, and the importance of mitigating the transmission of airborne diseases has been highlighted by the COVID-19 pandemic. On the other hand, the relatively high CO2 concentration of indoor environments presents a thermodynamic advantage for direct air capture (DAC) in comparison to atmospheric CO2 concentration. This review aims to describe the issues associated with poor IAQ, and to demonstrate the potential of indoor CO2 DAC to purify indoor air while generating a renewable carbon stream that can replace conventional carbon sources as a building block for chemical production, contributing to the circular economy, This project has received funding from the European Union's Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreements No 101018274 (L.R. López) and No 101029266 (P. Dessì). A. Cabrera-Codony acknowledges Programa Juan de la Cierva-Incorporación (IJC2020-045964-I) and funding from the Spanish Ministry of Science and Innovation (PID2020-112615RA-100). S. Puig is a Serra Húnter Fellow (UdG-AG-575), 7
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Boosting ethanol production rates from carbon dioxide in MES cells under optimal solventogenic conditions

  • Romans Casas, Meritxell
  • Perona Vico, Elisabet
  • Dessì, Paolo
  • Bañeras Vives, Lluís
  • Balaguer i Condom, Maria Dolors
  • Puig Broch, Sebastià
Microbial Electrosynthesis (MES) has been widely applied for acetic acid (HA) production from CO2 and electricity. Ethanol (EtOH) has a higher market value than HA, and wide application in industry and as a biofuel. However, it has only been obtained sporadically and at low concentrations, probably due to sub-optimal operating conditions. This study aimed at enhancing EtOH productivity in MES cells by jointly optimising key operation parameters, including pH, H2 and CO2 partial pressure (pH2 and pCO2), and HA concentration, to promote solventogenesis. Two H-type cells were operated in fed-batch mode at −0.8 V vs. SHE with CO2 as the sole carbon source. A mixed culture, enriched with Clostridium ljungdahlii was used as the biocatalyst. The combination of low pH (<4.5) and pCO2 (<0.3 atm), along with high HA concentration (about 6 g L−1) and pH2 (>3 atm), were mandatory conditions for maintaining an efficient solventogenic culture, dominated by Clostridium sp., capable of high-rate EtOH production. The maximum EtOH production rate was 10.95 g m−2 d−1, and a concentration of 5.28 g L−1 was achieved. Up to 30 % of the electrons and 15.2 % of the carbon provided were directed towards EtOH production, and 28.1 kWh were required for the synthesis of 1 kg of EtOH from CO2. These results highlight that strict conditions are required for a continuous, reliable, EtOH production in MES cells. Future investigation should focus on improving cell configuration to achieve EtOH production at higher current densities while minimizing the electric energy input, The authors acknowledge funding from the Spanish Ministry of Science and Innovation (PLEC2021-007802). M.R-C is grateful for the support of Spanish Government (FPU20/01362). P.D. has received funding from the European Union's Horizon 2020 research and innovation program under the Marie Skłodowska-Curie grant agreement No 101029266. S·P is a Serra Hunter Fellow (UdG-AG-575) and acknowledges the funding from the ICREA Academia award
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Indoor CO2 direct air capture and utilization: Key strategies towards carbon neutrality

  • López de León, Luis R.
  • Dessì, Paolo
  • Cabrera-Codony, Alba
  • Rocha-Melogno, Lucas
  • Kraakman, Bart
  • Balaguer i Condom, Maria Dolors
  • Puig Broch, Sebastià
Direct air capture (DAC) is a promising technology that can help to remove carbon dioxide (CO2) from the air. One application of DAC is indoor CO2 direct air capture (iCO2-DAC). A wide range of materials with unique properties for CO2 capture have been investigated, including porous materials, zeolites, and metal-organic frameworks. The selection of suitable materials for iCO2-DAC depends on several factors, such as cost, CO2 adsorption capacity, and stability. The development of new materials with improved properties for iCO2-DAC is an active research area. The captured CO2 can serve as a renewable carbon source to produce biofuels for internal use (e.g., for heating purposes), decreasing the environmental impact of buildings. This review article highlights the importance of iCO2-DAC to improve indoor air quality in buildings and boost the circular economy. We discuss the available carbon capture technologies and materials, discussing their properties and focusing on those potentially applicable to indoor environments. We also provide a hypothetic scenario where CO2 is captured from different indoor environments and transformed into sustainable fuels by using an emerging carbon capture and utilization technology (microbial electrosynthesis). Finally, we evaluate the economic feasibility of such an innovative approach in comparison to the use of traditional, fossil-based fuels, This project has received funding from the European Union’s Horizon 2020 research and innovation program under the Marie Skłodowska-Curie grant agreement No 101018274 (L.R. López) and No 101029266 (P. Dessì). A. Cabrera acknowledges Agencia Estatal de Investigación of the Spanish MCIU Programa Juan de la Cierva-Incorporación IJC2020-045964-I. S.P. is a Serra Húnter Fellow (UdG-AG-575) and acknowledges the funding from the ICREA Academia award. This publication is part of the R&D project (ref. TED2021–129452B-100), funded by MCIN/AEI/10.13039/501100011033/and, by the European Union Next Generation EU/PRTR. LEQUiA [2021-SGR-01352] has been recognized as a consolidated research group by the Catalan Government, Open Access funding provided thanks to the CRUE-CSIC agreement with Elsevier, 7
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Microbial electrosynthesis of acetate from CO2 in three-chamber cells with gas diffusion biocathode under moderate saline conditions

  • Dessì, Paolo|||0000-0002-9935-3038
  • Buenaño-Vargas, Claribel
  • Martínez-Sosa, Santiago|||0000-0003-2187-210X
  • Mills, Simon|||0000-0002-8682-3846
  • Trego, Anna
  • Ijaz, Umer Z.
  • Pant, Deepak|||0000-0002-1425-9588
  • Puig, Sebastià|||0000-0003-2995-1443
  • O'Flaherty, Vincent
  • Farràs Costa, Pau
The industrial adoption of microbial electrosynthesis (MES) is hindered by high overpotentials deriving from low electrolyte conductivity and inefficient cell designs. In this study, a mixed microbial consortium originating from an anaerobic digester operated under saline conditions (∼13 g L-1 NaCl) was adapted for acetate production from bicarbonate in galvanostatic (0.25 mA cm-2) H-type cells at 5, 10, 15, or 20 g L-1 NaCl concentration. The acetogenic communities were successfully enriched only at 5 and 10 g L-1 NaCl, revealing an inhibitory threshold of about 6 g L-1 Na+. The enriched planktonic communities were then used as inoculum for 3D printed, three-chamber cells equipped with a gas diffusion biocathode. The cells were fed with CO2 gas and operated galvanostatically (0.25 or 1.00 mA cm-2). The highest production rate of 55.4 g m-2 d-1 (0.89 g L-1 d-1), with 82.4% Coulombic efficiency, was obtained at 5 g L-1 NaCl concentration and 1 mA cm-2 applied current, achieving an average acetate production of 44.7 kg MWh-1. Scanning electron microscopy and 16S rRNA sequencing analysis confirmed the formation of a cathodic biofilm dominated by Acetobacterium sp. Finally, three 3D printed cells were hydraulically connected in series to simulate an MES stack, achieving three-fold production rates than with the single cell at 0.25 mA cm-2. This confirms that three-chamber MES cells are an efficient and scalable technology for CO2 bio-electro recycling to acetate and that moderate saline conditions (5 g L-1 NaCl) can help reduce their power demand while preserving the activity of acetogens.