Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

Radiative cooling characterization and optical properties of Cellulose-Derivative Networks

  • Manzano, Cristina V.
  • Díaz-Lobo, Alba
  • Gil-García, Marta
  • Rodríguez de la Fuente, Óscar
  • Morales-Sabio, Ángel
  • Martín-González, Marisol
All-day passive daytime radiative coolers offer a promising solution for energy-free cooling of buildings and devices. This Dataset is referring to this study, which investigates the use of various cellulose-derivative networks to achieve optimal and stable cooling performance. The results showed that the mixed cellulose ester network has a maximum solar reflectance of 97%, while cellulose acetate network has a maximum infrared emissivity of 96% in the atmospheric transparency window band, which is a near-perfect infrared emitter; the nitrocellulose network shows the highest cooling temperature, with a significant reduction of 14 °C from the ambient temperature and a power of 124 W·m−2 during the daytime and at night of 7.7 °C and 72.8 W·m−2. This study also analyzes the dampness's effect on the cooling performance of cellulose-derivative networks. The cooling performance of the nitrocellulose network drops ≈ 3 °C (from 14 to 11.3 °C) when the relative humidity of the day exceeds ≈ 30% is observed. These findings indicate that the capacity of a material to absorb water from the surrounding air significantly influences its performance as a passive cooler, primarily due to changes in its optical properties. This is an important insight, as it highlights the need to consider environmental factors like relative humidity and sample hydrophobicity for PDRC systems., Project 101087974 — COOLed. European Research Council (ERC), ADCP CV220524A_ATR_001 CV220524A_CCP CV220524A_SEM_001 CV220524A_SEM_002 CV220524A_SEM_003 CV220524B_ATR_001 CV220524B_CCP CV220524B_SEM_001 CV220524B_SEM_002 CV220524B_SEM_003 CV220524C_ATR_001 CV220524C_CCP CV220524C_SEM_001 CV220524C_SEM_002 CV220524C_SEM_003 IRE wet IRE RCT VISR wet VISR, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Performance and Relative Humidity Impact of Cellulose-Derivative Networks in All-Day Passive Radiative Cooling

  • Manzano, Cristina V.
  • Díaz-Lobo, Alba
  • Gil-García, Marta
  • Rodríguez de la Fuente, Óscar
  • Morales-Sabio, Ángel
  • Martín-González, Marisol
All-day passive daytime radiative coolers (PDRC) offer a promising solution for energy-free cooling of buildings and devices. This study investigates the use of various cellulose-derivative networks to achieve optimal and stable cooling performance. These results showed that the mixed cellulose ester network has a maximum solar reflectance of 97%. While cellulose acetate network has a maximum infrared emissivity of 96% in the atmospheric transparency window band, which is a near-perfect infrared emitter, the nitrocellulose network shows the highest cooling temperature, with a significant reduction of 14 °C from the ambient temperature and a power of 124 W·m−2 during the daytime and at night of 7.7 °C and 72.8 W·m−2. This study also analyzes the dampness's effect on the cooling performance of cellulose-derivative networks. The cooling performance of the nitrocellulose network drops ≈ 3 °C (from 14 to 11.3 °C) when the relative humidity of the day exceeds ≈ 30% is observed. These findings indicate that the capacity of a material to absorb water from the surrounding air significantly influences its performance as a passive cooler, primarily due to changes in its optical properties. This is an important insight, as it highlights the need to consider environmental factors like relative humidity and sample hydrophobicity for PDRC systems., C.V.M acknowledges financial support from “ERC Consolidator Grant No.101087974 COOLed” and from “Atracción de Talento Investigador” de la Comunidad de Madrid, contract 2019-T1/IND-13541. M.S.M.G acknowl-edge the MERGE project PID2020-118430GB-100. The authors acknowl-edge the service from the MiNa Laboratory at IMN, and funding from CM(project SpaceTec, S2013/ICE2822), MINECO (project CSIC13-4E-1794)and EU (FEDER, FSE). And the CSIC for the article processing charges., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Template-Assisted 3D-PVDF Nanonetworks for Passive Daytime Radiative Cooling

  • Iglesias-Elcano, Amaia
  • Moreno-Sanabria, Luis
  • Martín-González, Marisol
  • Manzano, Cristina V.
Passive daytime radiative cooling (PDRC), which dissipates heat through infrared emission to outer space while reflecting solar radiation, represents a promising strategy for reducing energy consumption in cooling technologies. Here, a template-assisted strategy is introduced to fabricate nanostructured polyvinylidene fluoride (PVDF) radiative coolers via polymer infiltration into three-dimensional anodic aluminum oxide (3D-AAO) nanoporous templates. The optical properties and cooling performance of the 3D-PVDF nanostructures are investigated with and without the AAO template. To tune the crystalline phase composition and its influence on optical response, three post-infiltration cooling methods—natural, fast, and ultra-fast—are applied. A UV treatment further enhances solar reflectance through photo-oxidation-induced whitening. The optimized free-standing 3D-PVDF obtained via ultra-fast cooling exhibits an average solar reflectance of 82.4% (0.32–2.5 μm) and an infrared emissivity of 96.7% within the 8–13 μm atmospheric window. These properties correspond to a theoretical daytime cooling power density of 182.3 W m<sup>−2</sup> under a solar irradiance of 1000 W m<sup>−2</sup>. Outdoor measurements demonstrate a daytime temperature reduction of 12.9°C under peak solar irradiance of 962 W m<sup>−2</sup> relative to an empty reference box. This work establishes a scalable strategy for engineering three-dimensional polymer nanostructures for high-performance radiative cooling and energy-efficient building technologies., We acknowledge financial support from “ERC Consolidator Grant No. 101087974 COOLed”. We acknowledge the service from the MiNa Laboratory at IMN and funding from EU (FEDER, FSE), MCIN/AEI/10.13039/501100011033 and Next Generation EU/PRTR (EQC2021-006944-P). We acknowledge support of the publication fee by the CSIC Open Access Publication Support Initiative through its Unit of Information Resources for Research (URICI)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

Template‐Assisted 3D‐PVDF Nanonetworks for Passive Daytime Radiative Cooling [Dataset]

  • Iglesias-Elcano, Amaia
  • Moreno-Sanabria, Luis
  • Martín-González, Marisol
  • Manzano, Cristina V.
Passive daytime radiative cooling (PDRC), which dissipates heat through infrared emission to outer space while reflecting solar radiation, represents a promising strategy for reducing energy consumption in cooling technologies. This Dataset is from the study in which we introduced a template-assisted strategy to fabricate nanostructured polyvinylidene fluoride (PVDF) radiative coolers via polymer infiltration into three-dimensional anodic aluminum oxide (3D-AAO) nanoporous templates. The optical properties and cooling performance of the 3D-PVDF nanostructures are investigated with and without the AAO template. To tune the crystalline phase composition and its influence on optical response, three post-infiltration cooling methods—natural, fast, and ultra-fast—are applied. A UV treatment further enhances solar reflectance through photo-oxidation-induced whitening. The optimized free-standing 3D-PVDF obtained via ultra-fast cooling exhibits an average solar reflectance of 82.4% (0.32–2.5 μm) and an infrared emissivity of 96.7% within the 8–13 μm atmospheric window. These properties correspond to a theoretical daytime cooling power density of 182.3 W m−2 under a solar irradiance of 1000 W m−2. Outdoor measurements demonstrate a daytime temperature reduction of 12.9°C under peak solar irradiance of 962 W m−2 relative to an empty reference box. This work establishes a scalable strategy for engineering three-dimensional polymer nanostructures for high-performance radiative cooling and energy-efficient building technologies., We acknowledge financial support from “ERC Consolidator Grant No. 101087974 COOLed”. We acknowledge the service from the MiNa Laboratory at IMN and funding from EU (FEDER, FSE), MCIN/AEI/10.13039/501100011033 and Next Generation EU/PRTR (EQC2021-006944-P). We acknowledge support of the publication fee by the CSIC Open Access Publication Support Initiative through its Unit of Information Resources for Research (URICI)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

High thermoelectric performance at room temperature in electrodeposited Ag2Se and Cu2Se films via microstructural control

  • Pérez Picazo, Elena
  • Tenaguillo Arrese, Miguel Ángel
  • Lohani, Ketan
  • Martín-González, Marisol
  • Manzano, Cristina V.
Electrodeposited silver selenide (Ag2Se) and copper selenide (Cu2Se) films are explored as scalable thermoelectric materials at room temperature (RT). The study focuses on the relationship between growth conditions, microstructure, and transport properties. For Ag2Se, a maximum in-plane power factor (PF) of 7655 ± 1578 μW m−1 K−2 is achieved, placing this material among the highest-performing n-type thermoelectrics at RT in terms of PF. The optimized films (Ag1.92Se) exhibit a dense granular morphology, strong (200) orthorhombic orientation, and minimal secondary phases; with an out-of-plane thermal conductivity (k) of 0.79 ± 0.16 W m−1 K−1. For Cu2Se, a maximum in-plane PF of 1130 ± 233 μW m−1 K−2 is obtained at RT, representing a five-fold improvement over previous electrodeposited Cu2Se films and approaching the highest values reported via vacuum-based methods. The optimized composition (Cu1.88Se) shows compact elongated grains and a predominantly cubic structure with (111) orientation; with an out-of-plane k of 0.89 ± 0.18 W m−1 K−1 at RT. The optimized materials were further integrated into a prototype π-type thermoelectric generator, delivering a maximum power density of 8.5 W m−2 under a temperature gradient of 12 K. These results establish electrodeposition as a simple and scalable platform for tuning microstructure and transport properties in chalcogenide films, yielding competitive thermoelectric performance at RT., We acknowledge financial support from “ERC Consolidator Grant No. 101087974 COOLed”. KL acknowledges Aid JDC2023-050703-I funded by MICIU/AEI/10.13039/501100011033 and by the ESF+. We acknowledge the service from the MiNa Laboratory at IMN, and funding from EU (FEDER, FSE), MCIN/AEI/10.13039/501100011033 and Next Generation EU/PRTR (EQ (C2021)-006944-P). We acknowledge support of the publication fee by the CSIC Open Access Publication Support Initiative through its Unit of Information Resources for Research (URICI)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

High thermoelectric performance at room temperature in electrodeposited Ag2Se and Cu2Se films via microstructural control [Dataset]

  • Pérez-Picazo, Elena
  • Tenaguillo, Miguel Ángel
  • Lohani, Ketan
  • Martín-González, Marisol
  • Manzano, Cristina V.
Electrodeposited silver selenide (Ag2Se) and copper selenide (Cu2Se) films are explored as scalable thermoelectric materials at room temperature (RT). The Dataset is from the study which focuses on the relationship between growth conditions, microstructure, and transport properties. For Ag2Se, a maximum in-plane power factor (PF) of 7655 ± 1578 μW m−1 K−2 is achieved, placing this material among the highest-performing n-type thermoelectrics at RT in terms of PF. The optimized films (Ag1.92Se) exhibit a dense granular morphology, strong (200) orthorhombic orientation, and minimal secondary phases; with an out-of-plane thermal conductivity (k) of 0.79 ± 0.16 W m−1 K−1. For Cu2Se, a maximum in-plane PF of 1130 ± 233 μW m−1 K−2 is obtained at RT, representing a five-fold improvement over previous electrodeposited Cu2Se films and approaching the highest values reported via vacuum-based methods. The optimized composition (Cu1.88Se) shows compact elongated grains and a predominantly cubic structure with (111) orientation; with an out-of-plane k of 0.89 ± 0.18 W m−1 K−1 at RT. The optimized materials were further integrated into a prototype π-type thermoelectric generator, delivering a maximum power density of 8.5 W m−2 under a temperature gradient of 12 K. These results establish electrodeposition as a simple and scalable platform for tuning microstructure and transport properties in chalcogenide films, yielding competitive thermoelectric performance at RT., We acknowledge financial support from “ERC Consolidator Grant No. 101087974 COOLed”. KL acknowledges Aid JDC2023-050703-I funded by MICIU/AEI/10.13039/501100011033 and by the ESF+. We acknowledge the service from the MiNa Laboratory at IMN, and funding from EU (FEDER, FSE), MCIN/AEI/10.13039/501100011033 and Next Generation EU/PRTR (EQ (C2021)-006944-P). We acknowledge support of the publication fee by the CSIC Open Access Publication Support Initiative through its Unit of Information Resources for Research (URICI)., Peer reviewed