Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 14
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Power control of a grid-connected PV system during asymmetrical voltage faults

  • Hunter, Gustavo
  • Riedemann, Javier
  • Andrade, Iván
  • Peña, Rubén
  • Blasco-Gimenez, Ramon|||0000-0003-3427-1581
[EN] Under voltage faults, grid-tied photovoltaic inverters should remain connected to the grid according to fault ride-through requirements. Moreover, it is a desirable characteristic to keep the power injected to grid constant during the fault. This paper explores a control strategy to regulate the active and reactive powers delivered by a single-stage photovoltaic generation system to the grid during asymmetrical voltage faults. The reference for the active power is obtained from a maximum power point tracking algorithm, whereas the reference for the reactive power can be set freely if the zero-sequence voltage is null; otherwise, it will depend on the magnitude of the zero-sequence voltage and the active power reference. The power control loop generates the reference currents to be imposed by the grid-tied power inverter. These currents are regulated by a predictive controller. The proposed approach is simpler than other methods proposed in the literature. The performance of the control strategy presented is verified with an experimental laboratory setup where voltage sags and swells are considered., This work was funded by Conicyt Chile Under Project FONDECYT 11180092. The financial support given by CONICYT/FONDAP/15110019 is also acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Indirect matrix converter modulation strategies for open-end winding induction machine

  • Riedemann, Javier
  • Peña Guiñez, Rubén
  • Cárdenas Dobson, Roberto
  • Clare, Jon
  • Blasco-Gimenez, Ramon|||0000-0003-3427-1581
[EN] In this paper an Indirect Matrix Converter (IMC) topology suitable for controlling an open-end winding induction machine is presented. The IMC is a direct power converter having no bulky energy storage elements with an input or current rectifying stage and a voltage source inverter as an output stage. To provide energy to an open-end winding induction machine two output stages are needed. Then, it is possible to obtain a voltage across any phase of the load up to 1.5 times the input phase voltage without overmodulation. Two pulse width modulation strategies are presented: the first one is based on space vector modulation that suppresses the zero sequence voltage in the load whereas the second one is a carrier-based modulation which generates lower distorted input converter currents. Results are presented and discussed., Este trabajo fue financiado por Fondecyt Chile bajo elcontrato 1121104. También se agradece el aporte financiero otorgado por CONICYT/FONDAP/15110019.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A DC-DC Converter Based On Modified Flyback Converter Topology

  • Pesce, C.
  • Riedemann, J.
  • Andrade, I.
  • Peña, R.
  • Blasco-Gimenez, Ramon|||0000-0003-3427-1581
[EN] This paper proposes a DC-DC power converter topology based on a modified Flyback Converter (FC). The aim of the proposed topology is to increase the voltage gain by connecting the inputs of N isolated FCs in parallel and the N secondary inductances in series. This scheme reduces the current in each switch then reducing the associated losses. A single diode and an output capacitance complete the power converter circuit. A Proportional+Integral (PI) controller is used to control the output voltage with the converter operating in discontinuous current mode. The proposed converter can handle more power than the standard FC with a low number of active power devices. The system is modeled using PSIM platform and experimental results are presented considering a 1kW prototype., Este trabajo fue financiado por Universidad de La Frontera, Temuco, Chile, bajo el proyecto DIUFRO17-0044. También se agradece el aporte financiero entregado por Fondecyt Chile bajo el contrato 1151325 y CONICYT/FONDAP/15110019 y al Ministerio de Economía Español por el contrato DPI2014- 53245-R
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Small-signal stability and fault performance of mixed grid forming and grid following offshore wind power plants connected to a HVDC-diode rectifier

  • Martínez-Turégano, Jaime|||0000-0002-3483-8253
  • Añó Villalba, Salvador Conrado|||0000-0002-8435-5225
  • Bernal-Perez, Soledad|||0000-0002-5431-9792
  • Blasco-Gimenez, Ramon|||0000-0003-3427-1581
  • Peña, Rubén
[EN] This study aims at validating the simultaneous operation of grid following and grid forming wind power plants when connected to a common diode rectifier-based HVDC link. The controllers for both grid forming and grid following wind turbines include fault-ride-through capability with soft restoration of the off-shore AC-grid. Current and voltage controllers are developed in the stationary alpha beta reference frame. The presented control and soft restoration strategies are based on local measurements only and do not require communication between wind turbine generators. The small-signal stability analysis of the mixed system in multiple d-q axis using detailed string models is carried out in order to show the sensitivity to grid following phase-locked-loop gains and to grid forming droop gains. Interoperability between grid forming and grid following wind turbines during transients is shown by means of detailed simulation during symmetric faults in different locations of the off-shore grid., The authors would like to thank the support of the Spanish Ministry of Economy and EU FEDER funds under grants DPI2014-53245-R and DPI2017-84503-R. This project has received funding from the European Union's Horizon 2020 research and innovation program under grant agreement No. 691714. Project partially funded by the EU through the Comunitat Valenciana2014-2020 European Regional Development Fund (FEDER) OperatingProgram (grant IDIFEDER/2018/036). The support provided by Fondecyt project 1201616 and CONICYT/FONDAP/1511001 is kindly acknowledged. ANID support through grant ANID/FONDAP/15110019 is kindly acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Application of Spectrometry for Determining the Solar Radiation of Deciduous Trees Shade: A Passive Energy Conservation Approach for Mediterranean Climates

  • Del Campo-Hitschfeld, María Luisa
  • Arenas, Nicolás
  • Rivera, Marco
  • Ballesteros-Pérez, Pablo|||0000-0002-4629-9664
[EN] Deciduous trees are well known for controlling solar gains in buildings, contributing to energy savings in a sector that consumes 35% of global energy. However, there is still a lack of information about the real thermal impact that deciduous trees have. This work proposes a new method that is cheap and easy to implement to quantify the shading efficiency of different types of deciduous trees in hot seasons. The results can be applied in energy evaluations of buildings. The trees selected belong to the central valley of Chile, which is characterized by hot summers and cold winters. The trees selected can also be found in other parts of the world. A spectrometer is used for measuring the amount of solar radiation (irradiance) that is present in the shadow of trees, measuring wavelengths between 339 nm and 750 nm (mostly within the visible light range). The full referential irradiance spectrum of the site is obtained by calibrating the standard ASTM G-173-03. At the site, the spectrometer is used to obtain the visible light range, while the infrared radiation (IR) and ultraviolet (UV) radiation ranges are obtained from the literature. Our results indicate that the analyzed deciduous trees reduce an average of 82% of the solar radiation. This information will help project designers during the building energy efficiency design phase by representative modeling of the solar radiation gains allowed by deciduous trees., This research was funded by FIC-R Maule Project BIP N°40.047.270-0; ANID/ATE220023 Project; FONDECYT Regular Research Project 1220556; CLIMAT AMSUD 21001 and FONDAP SERC Chile 15110019.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Vector control of an open-ended winding induction machine based on a two-output indirect matrix converter

  • Riedemann, Javier
  • Clare, Jon
  • Wheeler, Pat
  • Cardenas, Roberto
  • Peña, Ruben
  • Blasco-Gimenez, Ramon|||0000-0003-3427-1581
[EN] The open-ended winding induction machine fed from a standard two-level Voltage Source Inverter (VSI) arrangement is an attractive solution for AC drives. An alternative power converter approach is to use an Indirect Matrix Converter (IMC) consisting of a matrix converter AC-DC input stage and two VSI output stages. This latter topology provides fully bidirectional power flow operation and requires only a small input filter. In this paper, a vector control strategy for an open-ended winding cage induction machine fed by a two-output IMC is presented. The modulation scheme for the input power converter stage aims to modify the virtual DC link voltage depending on the load voltage requirement. Additionally, the modulation strategy for the dual-inverter output aims to eliminate the zero sequence voltage applied to the load. A vector control scheme is used and the full system is modelled using a PSIM and MATLAB/Simulink platform. Experimental results from a 7.5 kW prototype are presented, demonstrating the feasibility of the topology and control strategy., This work was supported by The Chilean Research Fondecyt [grant number 1151325]; CONICYT/FONDAP/15110019.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Open-End Winding Induction Machine Fed by a Dual-Output Indirect Matrix Converter

  • Riedemann, Javier
  • Clare, J.C.
  • Wheeler, P.W.
  • Rivera, Marco
  • Peña, Rubén
  • Blasco-Gimenez, Ramon|||0000-0003-3427-1581
[EN] Open-ended winding induction machines fed from standard two-level voltage source inverters (VSIs) provide an attractive arrangement for ac drives. An alternative approach is to use a dual-output indirect matrix converter (IMC). It is well known that the IMC provides fully bidirectional power flow operation, with small input size filter requirements. While a standard IMC consists of an ac dc matrix converter (MC) input stage followed by a single VSI output stage, it is possible to replicate the VSI to produce multiple outputs. In this paper, an open-end winding induction machine fed by an IMC with two output stages is presented. The IMC modulation strategy aims to reduce the common-mode voltage (CMV), while compensating any zero-sequence voltage fed to the machine. The system is modeled using a PSIM and MATLAB/Simulink platform. Experimental results demonstrating the viability of the method are presented using a 7.5-kW prototype., This work was supported in part by the Fondecyt/1151325, in part by the CONICYT/FONDAP/15110019, and in part by The Newton Picarte Project EPSRC: EP/N004043/1: New Configurations of Power Converters for Grid Interconnection Systems/CONICYT DPI20140007.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

An Active/Reactive Power Control Strategy for Renewable Generation Systems

  • Andrade, Iván
  • Pena, Rubén
  • Riedemann, Javier
  • Jara, Werner
  • Pesce, Cristián
  • Blasco-Gimenez, Ramon|||0000-0003-3427-1581
[EN] The development of distributed generation, mainly based on renewable energies, requires the design of control strategies to allow the regulation of electrical variables, such as power, voltage (V), and frequency (f), and the coordination of multiple generation units in microgrids or islanded systems. This paper presents a strategy to control the active and reactive power flow in the Point of Common Connection (PCC) of a renewable generation system operating in islanded mode. Voltage Source Converters (VSCs) are connected between individual generation units and the PCC to control the voltage and frequency. The voltage and frequency reference values are obtained from the P-V and Q-f droop characteristics curves, where P and Q are the active and reactive power supplied to the load, respectively. Proportional-Integral (PI) controllers process the voltage and frequency errors and set the reference currents (in the dq frame) to be imposed by each VSC. Simulation results considering high-power solar and wind generation systems are presented to validate the proposed control strategy., This research was funded by ANID/FONDAP/15110019, by ANID/FONDECYT/1201616, and by ANID/PIA/ACT192013. This work was also supported by the Spanish Ministry of Economy and EU FEDER Funds under grant DPI2017-84503-R. Project partially funded by the EU through the Comunitat Valenciana 2014-2020 European Regional Development Fund (FEDER) Operating Program (grant IDIFEDER/2018/036).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A multilevel modular DC DC converter topology

  • Vidal, R.
  • Soto, D.
  • Andrade, I.
  • Riedemann, J.
  • Pesce, C.
  • Belenguer, E.
  • Pena, R.
  • Blasco-Gimenez, Ramon|||0000-0003-3427-1581
[EN] A multilevel modular DC DC power conversion topology based on cascaded H-Bridge converters in a double II configuration is presented. The topology is intended to interconnect large power DC networks. A two level control hierarchy is used to regulate the DC voltage of each H-bridge module. At the top level, DC and circulating AC currents are used to control the total energy converter in all branches (both parallels and series) of each II arrange. At bottom level, the voltage balance of a converter branch, which comprises N H-bridge modules, is carried out by balancing (N-1) capacitor voltage deviations, with respect to the average capacitor voltage. The entire topology and control strategies are simulated in a PSIM environment. Simulation results with three H-bridge converters per branch are shown and preliminary experimental results with a low power prototype are also included., This work was supported by Fondecyt grant 1151325, CONICYT/FONDAP/15110019, The Spanish Ministry of Economy and EU FEDER funds under grant DPI2014-53245-R, The University of Magallanes grant PR-FI-02IE14/15, Universitat Jaume I grant P1.1B2013-51, the Newton Picarte Project EPSRC:EP/N004043/1 and CONICYT DPI20140007.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A probabilistic economic dispatch model and methodology considering renewable energy, demand and generator uncertainties

  • Arriagada, E.
  • López, E.
  • López, M.
  • Roa, C.
  • Poloujadoff, M.
  • Blasco-Gimenez, Ramon|||0000-0003-3427-1581
[EN] This article propose a probabilistic economic dispatch model that integrates thermal generating units (fuel-based), photovoltaic arrays, and wind energy conversion systems. Wind speed, solar irradiance, and power demand are treated as random variables, and the unavailability of each source type is explicitly considered. The solution approach combines Monte Carlo sampling with nonlinear constrained optimization. The optimal dispatch is characterized using single- and multidimensional probability analyses, descriptive statistics, clustering, and bimodal analysis. The methodology yields probability distributions for the system marginal price, thermal (fuel-based), solar and wind power generation, and load shedding. The model and methodology are applied to a case study of the Northern Chilean power system., The authors would like to thank the financial support by the FONDECYT Regular Project No. 1120178 and CONICYT/FONDAP/15110019 of the Chilean National Scientific and Technological Research Commission (CONICYT). This work has been partially funded by the "Programa Basal del ISCI (FBO-16) - CHILE". Dr R. Blasco-Gimenez would like to thank the Spanish Ministry of Science and Innovation for their support under Grant DPI2010-16714.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Sizing and Short-Circuit Capability of a Transformerless HVDC DC-DC Converter

  • Vidal-Albalate, Ricardo
  • Soto-Sánchez, Diego
  • Belenguer, Enrique
  • Peña, Rubén
  • Blasco-Gimenez, Ramon|||0000-0003-3427-1581
[EN] This work aims at optimizing the converter design of the double-T MMC DC-DC converter in terms of transmitted power per submodule and also in terms of transmitted power per silicon area, while, at the same time, providing the capability to block dc faults. Firstly, the converter operation is described and the optimal values of the inner ac and dc voltages that minimize device power rating are derived. Next, the submodule topology is analyzed and a thorough study on the converter capability for blocking fault currents is carried out, showing that the converter is able to isolate dc faults both at the input and at the output of the converter. Finally, the previous analytical study is verified by means of detailed PSCAD simulations., This work was supported by Spanish Ministry of Economy and EU FEDER Funds under Grants DPI2014-53245-R and DPI2017-84503-R. This work was supported by the EU through the Comunitat Valenciana 2014-2020 European Regional Development Fund (FEDER) Operating Program under Grant IDIFEDER/2018/036. This work was supported by the Fondecyt project 1201616 and CONICYT/FONDAP/15110019 is kindly acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Control of PMSG-based wind turbines in weak grids during unbalanced faults

  • Blasco-Gimenez, Ramon|||0000-0003-3427-1581
  • Añó Villalba, Salvador Conrado|||0000-0002-8435-5225
  • Peña, R.S.
[EN] This paper includes the study of a control strategy for the connection of PMSG-based wind turbines during unbalanced faults in weak grids. The wind turbine front-end converter is controlled in the stationary frame by the direct calculation of current references. In this way, it is possible to keep a reasonably smooth generated power during the fault, in order to reduce the fault impact on the wind turbine mechanical components. The effects on the mechanical parts of the wind turbine have been studied by using the NREL 5 MW reference wind turbine, modeled with the NREL FAST code., The present work was supported by the Spanish Ministry of Science and Technology funds under Grant DPI2010- 16714, and by the Generalitat Valenciana funds under Grant ACOMP/2013/116. The financial support of Fondecyt Chile under Contract 1121104 and CONICYT/FONDAP/15110019 is also kindly acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Model aggregation of large wind farms for dynamic studies

  • Martínez-Turégano, Jaime|||0000-0002-3483-8253
  • Añó Villalba, Salvador Conrado|||0000-0002-8435-5225
  • Bernal-Perez, Soledad|||0000-0002-5431-9792
  • Blasco-Gimenez, Ramon|||0000-0003-3427-1581
  • Chaqués-Herráiz, G.
[EN] A large number of nodes is required for the detailed simulation of large off-shore wind farms. Therefore, the corresponding electromagnetic transient simulations require large simulation times. This paper compares a detailed model of an off-shore wind farm with three clusters of 50 wind turbines each one (i.e. a total of 150 wind turbines), with a simplified model consisting of three aggregated wind farms. The paper includes the aggregation criteria so equal power flows and voltages are obtained at the wind farms points of common coupling. The control is carried out using a centralized PI controller to control total active power, and a distributed droop control for active and reactive power control of each wind turbine. The proposed aggregation method leads to significant savings on computational times, with the aggregated models being more than three hundred and fifty times faster than the detailed ones. The results have been validated by means of detailed PSCAD/EMTDC simulations.v, The authors would like to thank the support of the Spanish Ministry of Economy and EU FEDER funds under grant DPI2014-53245-R. The support of CONICYT/FONDAP/15110019 and Fondecyt 1151325 is also kindly acknowledged. This project has received funding from the European Union's Horizon 2020 research and innovation program under grant agreement No. 691714.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

DC Current Harmonics Reduction in Multi-Inverter Topology

  • Reyes, Eduardo
  • Sarasiri, Nuapett
  • Pena, Ruben
  • Riedemann, Javier
  • Andrade, Iván
  • Jara, Werner
  • Blasco-Gimenez, Ramon|||0000-0003-3427-1581
[EN] This letter presents a Space Vector Pulse Width Modulation (SVPWM) strategy for reducing the DC-link current harmonics in a multi- Voltage Source Inverter (VSI) topology with common DC-link bus. The DC current harmonic reduction is achieved by phase-shifting the PWM pattern of individual VSIs, with the inverters sharing the system total power. Simulation and experimental results are shown to validate the proposal., This work was supported by ANID/FONDAP/15110019 and in part by ANID/FONDECYT/1201616.