Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 11
Encontrada(s) 1 página(s)

Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Comparing continuous and batch operation for high-rate treatment of urban wastewater

  • Rey-Martínez, Natalia|||0000-0003-1434-8596
  • Barreiro-López, Aloia
  • Guisasola, Albert|||0000-0002-3012-7964
  • Baeza, Juan Antonio|||0000-0003-1290-1669
The water-energy nexus has changed the concept of wastewater treatment plants (WWTPs), which should move from energy consumers into energy neutral or even energy positive facilities. The A/B process aims at achieving self-sufficient energy WWTPs: organic matter is removed in the first step (A-stage) and derived to biogas production whereas autotrophic nitrogen removal is implemented in a second step (B-stage). This work compares two high-rate systems that can be used as A-stage in view of organic matter removal: a continuous high rate activated sludge (HRAS) reactor and a high-rate sequencing batch reactor (HRSBR). Both systems were operated with real urban wastewater at a short hydraulic retention time (2.5 h) and at short sludge retention time (SRT) of 1-2 d to minimize COD mineralization and to maximize organic matter diversion to methane production and, hence, energy recovery. The HRAS showed higher COD removal efficiencies and better energy recovery. On the other hand, the HRSBR was better to avoid undesired nitrification and provided lower COD mineralization for all the SRTs tested (ranging 20-48% for the HRSBR, and 41-58% for the HRAS). Then, the energy as methane recovered per unit of COD degraded was higher in the HRSBR. The HRSBR seems to be a good option, because the solids content in the effluent was similar for both systems and its COD removal efficiency can be further improved by optimizing the SBR cycle configuration.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Nitrite and nitrate inhibition thresholds for a glutamate-fed bio-P sludge

  • Rey-Martínez, Natalia|||0000-0003-1434-8596
  • Merdan, Gökçe
  • Guisasola, Albert|||0000-0002-3012-7964
  • Baeza, Juan Antonio|||0000-0003-1290-1669
Enhanced biological phosphorus removal (EBPR) is an efficient and sustainable technology to remove phosphorus from wastewater. A widely known cause of EBPR deterioration in wastewater treatment plants (WWTPs) is the presence of nitrate/nitrite or oxygen in the anaerobic reactor. Moreover, most existing studies on the effect of either permanent aerobic conditions or inhibition of EBPR by nitrate or free nitrous acid (FNA) have been conducted with a "Candidatus Accumulibacter" or Tetrasphaera-enriched sludge, which are the two major reported groups of polyphosphate accumulating organisms (PAO) with key roles in full-scale EBPR WWTPs. This work reports the denitrification capabilities of a bio-P microbial community developed using glutamate as the sole source of carbon and nitrogen. This bio-P sludge exhibited a high denitrifying PAO (DPAO) activity, in fact, 56% of the phosphorus was uptaken under anoxic conditions. Furthermore, this mixed culture was able to use nitrite and nitrate as electron acceptor for P-uptake, being 1.8 μg HNO-N·L the maximum FNA concentration at which P-uptake can occur. Net P-removal was observed under permanent aerobic conditions. However, this microbial culture was more sensitive to FNA and permanent aerobic conditions compared to "Ca. Accumulibacter"-enriched sludge.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Implementation of a sulfide-air fuel cell coupled to a sulfate-reducing biocathode for elemental sulfur recovery

  • Blazquez Ribas, Enric|||0000-0001-6748-8950
  • Gabriel, David|||0000-0002-7713-4192
  • Baeza, Juan Antonio|||0000-0003-1290-1669
  • Guisasola, Albert|||0000-0002-3012-7964
  • Ledezma, Pablo|||0000-0003-1366-639X
  • Freguia, Stefano|||0000-0002-2294-9036
Bio-electrochemical systems (BES) are a flexible biotechnological platform that can be employed to treat several types of wastewaters and recover valuable products concomitantly. Sulfate-rich wastewaters usually lack an electron donor; for this reason, implementing BES to treat the sulfate and the possibility of recovering the elemental sulfur (S) offers a solution to this kind of wastewater. This study proposes a novel BES configuration that combines bio-electrochemical sulfate reduction in a biocathode with a sulfide-air fuel cell (FC) to recover S. The proposed system achieved high elemental sulfur production rates (up to 386 mg S-S L d) with 65% of the sulfate removed recovered as S and a 12% lower energy consumption per kg of S produced (16.50 ± 0.19 kWh kg S-S) than a conventional electrochemical S recovery system.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Less is more, a comprehensive study on the effects of the unmber of gas diffusion layers on air-cathode microbial fuel cells

  • Sánchez Peña, Pilar|||0000-0002-7825-4890
  • Rodriguez, Jesús|||0000-0002-8601-0466
  • Montes, Raquel|||0000-0001-8805-9987
  • Baeza, Juan Antonio|||0000-0003-1290-1669
  • Gabriel, David|||0000-0002-7713-4192
  • Baeza, Mireia|||0000-0002-2240-6410
  • Guisasola, Albert|||0000-0002-3012-7964
Air-cathode microbial fuel cells (AC-MFC) use a gas-diffusion-layer (GDL) coating based on polytetrafluoroethylene applied to the cathode to prevent electrolyte leakage. However, this type of GDL can also lead to a decrease in MFC performance due to electron-transfer limitation, mass-transfer limitation or catalyst availability. This study provides a comprehensive understanding of the significance of the GDL coating, demonstrating the interaction between the number of GDL coatings and the external resistance (Rext) used. An experimental design in 28 mL AC-MFCs was prepared and conducted using two different Rext (10 and 249 Ω) and four different GDL coatings (1 to 4 layers). The coating effect was not significant when operating with a high Rext, where the electron transfer was the limiting process. However, when the Rext was low, the amount of polytetrafluoroethylene limited the cathode performance due to a significant decrease in the Pt availability on the catalytic surface. Thus, GDL-1 with 10 Ω as Rext reached 0.96 mA/cm2, 3-fold higher than that obtained with 249 Ω as Rext (ca. 0.30 mA/cm2). Besides, the current density did not vary noticeably in the other cathodes with 249 Ω as Rext. Contrarily, the current density with 10 Ω as Rext decreased as the number of GDL increased (0.74, 0.57 and 0.37 for GDL-2, GDL-3 and GDL-4 respectively). These values agreed with those of the polarization curve. Furthermore, limitations were also observed in electrochemical impedance spectroscopy measurements: the charge resistance increased with the number of GDL, related to the ease of electron flow. These values were18 Ω, 22 Ω, 53 Ω and 58 Ω for GDL-1, GDL-2, GDL-3 and GDL-4, respectively, for both 10 and 249 Ω cathodes.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Evaluation of the integration of P recovery, polyhydroxyalkanoate production and short cut nitrogen removal in a mainstream wastewater treatment process

  • Larriba, Oriol|||0000-0002-7407-6185
  • Rovira-Cal, Eric
  • Juznic-Zonta, Zivko|||0000-0002-2362-9771
  • Guisasola, Albert|||0000-0002-3012-7964
  • Baeza, Juan Antonio|||0000-0003-1290-1669
Wastewater treatment systems are nowadays evolving into systems where energy and resources are recovered from wastewater. This work presents the long term operation of a demo-scale pilot plant (7.8 m(3)) with a novel configuration named as mainstream SCEPPHAR (ShortCut Enhanced Phosphorus and polyhydroxyalkanoate (PHA) Recovery) and based on two sequencing batch reactors (R1-HET and R2-AUT). This is the first report of an implementation at demo scale and under relevant operational conditions of the simultaneous integration of shortcut nitrification, P recovery and production of sludge with a higher PHA content than conventional activated sludge. An operating period under full nitrification mode achieved successful removal efficiencies for total N, P and CODT (86 +/- 12%, 93 +/- 9% and 79 +/- 6%). In the following period, nitrite shortcut (with undetectable activity of nitrite oxidising bacteria) was achieved by implementing automatic control of the aerobic phase length in R2-AUT using ammonium measurement andoperating at a lower sludge retention time. Similar N, P and CODT removal efficiencies to the full nitrification period were obtained. P-recovery from the anaerobic supernatant of R1-HET was achieved in a separate precipitator by increasing pH and dosing MgCl2, recovering an average value of 45% of the P in the influent as struvite precipitate, with a peak up to 63%. These values are much higher than the typical values of sidestream P-recovery (12%). Regarding PHA, a percentage in the biomass in the range 6.9-9.2% (gPHA.g(-1)TSS) was obtained.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Systematic calibration of N2O emissions from a full-scale WWTP including a tracer test and a global sensitivity approach

  • Solis Duran, Borja|||0000-0003-0305-6168
  • Guisasola, Albert|||0000-0002-3012-7964
  • Pijuan Vilalta, Maria Teresa|||0000-0002-6468-6203
  • Corominas, L.
  • Baeza, Juan Antonio|||0000-0003-1290-1669
Nitrous oxide (NO) is a greenhouse gas (GHG) emitted during biological nitrogen removal from wastewater treatment plants (WWTPs). Some modelling tools have been proposed to predict NO emissions during the design and operation of WWTPs. In this study, the novel ASM2d-NO model, which accounts for the production of NO in nutrient removal WWTPs, was used to study the associated emissions from a full-scale WWTP with two independent lines. Firstly, the hydraulics of the WWTP was characterized by a residence time distribution test, showing the flow was equally divided into the two treatment lines (49.3 vs. 50.7%), that each reactor worked as an ideal continuous stirred tank reactor and the secondary settler model flux was similar to a plug-flow reactor. The ASM2d-NO model was then calibrated using experimental data obtained under dynamic conditions. A global sensitivity analysis was used to select, among 59 model parameters, five candidates that resulted to be related to nitrifying organisms. Different parameter subsets up to four parameters were evaluated, being the subset [µ, q, K, K] the best, achieving 53.3% reduction of the calibration cost function. The model fit obtained provided a reasonably description of nutrients and NO emission trends, considering the inherent operational variability suffered in full-scale WWTPs. Finally, a simulation-based study showed that, for the given WWTP and operational conditions, an unbalanced distribution of flow-rate between the two treatment lines did not result in a significant increase on NO emissions. The results obtained show that this model can be a suitable tool for predicting NO emissions in full-scale WWTPs, and can therefore be used to find operational conditions that help to minimise these emissions.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

A plant-wide model describing GHG emissions and nutrient recovery options for water resource recovery facilities

  • Solis Duran, Borja|||0000-0003-0305-6168
  • Guisasola, Albert|||0000-0002-3012-7964
  • Flores Alsina, Xavier|||0000-0002-9310-0240
  • Jeppsson, Ulf
  • Baeza, Juan Antonio|||0000-0003-1290-1669
In this study, a plant-wide model describing the fate of C, N and P compounds, upgraded to account for (on-site/off-site) greenhouse gas (GHG) emissions, was implemented within the International Water Association (IWA) Benchmarking Simulation Model No. 2 (BSM2) framework. The proposed approach includes the main biological N2O production pathways and mechanistically describes CO2 (biogenic/non-biogenic) emissions in the activated sludge reactors as well as the biogas production (CO2/CH4) from the anaerobic digester. Indirect GHG emissions for power generation, chemical usage, effluent disposal and sludge storage and reuse are also included using static factors for CO2, CH4 and N2O. Global and individual mass balances were quantified to investigate the fluxes of the different components. Novel strategies, such as the combination of different cascade controllers in the biological reactors and struvite precipitation in the sludge line, were proposed in order to obtain high plant performance as well as nutrient recovery and mitigation of the GHG emissions in a plant-wide context. The implemented control strategies led to an overall more sustainable and efficient plant performance in terms of better effluent quality, reduced operational cost and lower GHG emissions. The lowest N2O and overall GHG emissions were achieved when ammonium and soluble nitrous oxide in the aerobic reactors were controlled and struvite was recovered in the reject water stream, achieving a reduction of 27% for N2O and 9% for total GHG, compared to the open loop configuration.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Graphene functionalization with metallic Pt nanoparticles, A path to cost-efficient H2 production in microbial electrolysis cells

  • Sánchez Peña, Pilar|||0000-0002-7825-4890
  • Rodriguez, Jordi
  • Gabriel, David|||0000-0002-7713-4192
  • Baeza, Juan Antonio|||0000-0003-1290-1669
  • Guisasola, Albert|||0000-0002-3012-7964
  • Baeza, Mireia|||0000-0002-2240-6410
Platinum is one of the most widely used catalysts in the cathode of Microbial Electrolysis Cells (MECs) to overcome the relatively slow kinetics of hydrogen evolution, even though it is not economically feasible on a large scale. This work aims at developing, applying, characterizing, and optimizing two novel Pt-functionalized inks with promising characteristics: Pt@rGO based on reduced graphene oxide and Pt@Graphitene based on a home-made material named Graphitene, which showed improved performance at a lower cost. The Pt-functionalized materials were deposited on carbon cloth and used as cathode electrode in a single chamber MEC. These materials provided 47% increase in Pt functionalization over commercial inks. Moreover, surface areas of 10.76 m/g and 24.40 m/g and electroactive areas of 0.10 cm/cm and 0.16 cm/cm were determined for Pt@Graphitene and Pt@rGO, respectively, a difference caused by structural defects in the case of the Pt@rGO, which slightly improved its performance compared to Pt@Graphitene. Thus, the experimental results reached ca. 0.8 mA/cm, a 43% higher intensity than that obtained using conventional commercial inks.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

A review on the integration of mainstream P-recovery strategies with enhanced biological phosphorus removal

  • Zhang, Congcong|||0000-0003-3693-4705
  • Guisasola, Albert|||0000-0002-3012-7964
  • Baeza, Juan Antonio|||0000-0003-1290-1669
Phosphorus (P), an essential nutrient for all organisms, urgently needs to be recovered due to the increasing demand and scarcity of this natural resource. Recovering P from wastewater is a feasible and promising way widely studied nowadays due to the need to remove P in wastewater treatment plants (WWTPs). When enhanced biological P removal (EBPR) is implemented, an innovative option is to recover P from the supernatant streams obtained in the mainstream water line, and then combine it with liquor-crystallisation recovery processes, being the final recovered product struvite, vivianite or hydroxyapatite. The basic idea of these mainstream P-recovery strategies is to take advantage of the ability of polyphosphate accumulating organisms (PAO) to increase P concentration under anaerobic conditions when some carbon source is available. This work shows the mainstream P-recovery technologies reported so far, both in continuous and sequenced batch reactors (SBR) based configurations. The amount of extraction, as a key parameter to balance the recovery efficiency and the maintenance of the EBPR of the system, should be the first design criterion. The maximum value of P-recovery efficiency for long-term operation with an adequate extraction ratio would be around 60%. Other relevant factors (e.g. COD/P ratio of the influent, need for an additional carbon source) and operational parameters (e.g. aeration, SRT, HRT) are also reported and discussed.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Exploring GHG emissions in the mainstream SCEPPHAR configuration during wastewater resource recovery

  • Solís, B.
  • Guisasola, Albert|||0000-0002-3012-7964
  • Pijuan Vilalta, Maria Teresa|||0000-0002-6468-6203
  • Baeza, Juan Antonio|||0000-0003-1290-1669
The wastewater sector paradigm is shifting from wastewater treatment to resource recovery. In addition, concerns regarding sustainability during the operation have increased. In this sense, many water utilities have become aware of the potential GHG emissions during the operation of wastewater treatment. This study assesses the nitrous oxide and methane emissions during the long-term operation of a novel wastewater resource recovery facility (WRRF) configuration: the mainstream SCEPPHAR. The long-term NO and CH emission factors calculated were in the low range of the literature, 1 % and 0.1 %, respectively, even with high nitrite accumulation in the case of NO. The dynamics and possible sources of production of these emissions are discussed. Finally, different aeration strategies were implemented to study the impact on the NO emissions in the nitrifying reactor. Results showed that operating the pilot-plant under different dissolved oxygen concentrations (between 1 and 3 g O m) did not have an effect on the NO emission factor. Intermittent aeration was the aeration strategy that most mitigated the NO emissions in the nitrifying reactor, obtaining a reduction of 40 % compared to the normal operation of the pilot plant.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Exploring the stability of an A-stage-EBPR system for simultaneous biological removal of organic matter and phosphorus

  • Zhang, Congcong|||0000-0003-3693-4705
  • Guisasola, Albert|||0000-0002-3012-7964
  • Baeza, Juan Antonio|||0000-0003-1290-1669
This work evaluates the performance and stability of a continuous anaerobic/aerobic A-stage system with integrated enhanced biological phosphorus removal (A-stage-EBPR) under different operational conditions. Dissolved oxygen (DO) in the aerobic reactor was tested in the 0.2-2 mgDO/L range using real wastewater amended with propionic acid, obtaining almost full simultaneous COD and P removal without nitrification in the range 0.5-1 mgDO/L, but failing at 0.2 mgDO/L. Anaerobic purge was tested to evaluate a possible mainstream P-recovery strategy, generating a P-enriched stream containing 22% of influent P. COD and N mass balances indicated that about 43% of the influent COD could be redirected to the anaerobic digestion for methane production and 66% of influent NH4+-N was discharged in the effluent for the following N-removal B-stage. Finally, when the system was switched to glutamate as sole carbon source, successful EBPR activity and COD removal were maintained for two months, but after this period settleability problems appeared with biomass loss. Microbial community analysis indicated that Propionivibrio, Thiothrix and Lewinella were the most abundant species when propionic acid was the carbon source and Propionivibrio was the most favoured with glutamate. Thiothrix, Hydrogenophaga, Dechloromonas and Desulfobacter appeared as the dominant polyphosphate-accumulating organisms (PAOs) under different operation stages.