Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 13
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Development of CO2 Protective Layers by Spray Pyrolysis for Ceramic Oxygen Transport Membranes

  • García Torregrosa, Iván
  • Lobera González, Maria Pilar
  • Solis Díaz, Cecilia
  • Atienzar Corvillo, Pedro Enrique|||0000-0002-0356-021X
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] Ceramic mixed ionic¿electronic conducting (MIEC) membranes enable very selective oxygen separation from air at high temperatures. Two major potential applications of oxygen-transport membranes are: i) oxygen production for oxyfuel power plants, and, ii) integration within high-temperature catalytic membrane reactors for methane or alkane upgrading by selective oxidative conversions. However, these applications involve contact with carbon-bearing atmospheres and most state-of-the-art highly permeable MIEC membranes do not tolerate operation under CO 2 -rich environments due to carbonation processes. The present contribution shows our ¿ rst attempts in the development of ceria-based protective thin layers on monolithic LSCF membranes. Gd-doped ceria (CGO) deposition is carried out by air blast spray pyrolysis on mirror-polished LSCF disc membranes. The layer thickness is maintained below 0.4 ¿ m in order to prevent the formation of cracks during thermal cycling and minimize limitations caused by the reduced oxygen permeability through the ceria layer. After optimization of the spraying process, smooth crack-free dense coatings are obtained with high crystallinity in the as-deposited state. The layers are characterized by XRD, SEM, AFM, DC-conductivity measurements, interferometry and optical microscopy. Oxygen separation is studied on coated LSCF using air as the feed and argon/CO 2 mixtures as the sweep gas in the temperature range 650¿1000 ° C. The protected membrane exhibits a higher stability than the uncoated LSCF membrane, although the nominal oxygen ¿ ux is slightly reduced at temperatures below 850 ° C due to the limited ambipolar conductivity of doped ceria in the range of oxygen partial pressures investigated. Moreover, the protective layer (250 nm thickness) remains stable after the permeation testing., Financial support by the Spanish Ministry for Science and Innovation (Project ENE2008-06302 and FPI Grant JAE-Pre 08-0058), the EU through FP7 NASA-OTM Project (NMP3-SL-2009-228701), and the Helmholtz Association of German Research Centers through the Helmholtz Alliance MEM-BRAIN (Initiative and Networking Fund) is kindly acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Study of the transport properties of the mixed ionic electronic conductor Ce 1-x Tb x O 2- + Co (x=0.1, 0.2) and evaluation as oxygen-transport membrane

  • Balaguer Ramirez, Maria|||0000-0002-7098-9235
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
  • Solis Díaz, Cecilia
[EN] Tb-doped ceria materials have been synthesized by the coprecipitation method. Cobalt oxide (2 mol %) has been added in order to improve the sinterability and conductivity. XRD measurements suggest that a part of the cobalt is incorporated in the ceria lattice. Ce1¿xTbxO2¿¿ materials showed predominantly ionic conductivity, but the mixed ionic electronic conductivity can be tuned by modifying Tb and Co doping level and temperature range. The ambipolar conductivity was determined by galvanic method coupled with gas permeation and these results support the applicability of these materials as oxygen transport membranes at high temperature. Ce1¿xTbxO2¿¿ +Co membranes are CO2 stable and yielded oxygen fluxes that can compete with reported perovskite materials. Oxygen diffusion and surface exchange coefficients in the range 1 ¿ 10¿5 to 1 ¿ 10¿4 cm2/s and 1 ¿ 10¿4 to 1 ¿ 10¿3 cm/s from 773 to 1023 K have been obtained by conductivity relaxation., Financial support by the Spanish Ministry for Science and Innovation (Project ENE2008-06302, Grant JAE-Pre 08-0058, and Grant BES-2009-015835), Spanish Industry Ministry (Project IAP-560620-2008-17), the EU through FP7 NASA-OTM Project (NMP3-SL-2009-228701) and Instalaciones Inabensa S.A. is kindly acknowledged. The help of Dr. Jorda (HT-XRD) is kindly acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Ultrahigh oxygen permeation flux through supported Ba0.5Sr0.5Co0.8Fe0.2O3-delta membranes

  • Baumann, S.
  • Lobera González, Maria Pilar
  • Schulze-Kueppers, F.
  • Meulenberg, W. A.
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
  • Escolástico Rozalén, Sonia|||0000-0002-7097-2425
[EN] Oxygen transport membranes made of Ba0.5Sr0.5Co0.8Fe0.2O3-delta (BSCF) were manufactured by tape casting and co-firing. The disk-shaped membranes consisted of a top gastight layer (70 mu m thick) and a porous substrate (830 mu m thick) with 34% open porosity. The variation of the permeation operation conditions allowed (i) the identification of the different limitations steps in the permeation process, i.e., bulk oxygen ion diffusion, catalytic surface exchange and gas phase diffusion in the membrane compartments and porous substrate, and (ii) the ultimate optimization of the oxygen flux. The variables considered in the systematic permeation study included the inlet gas flow rate of the sweep and air feed, the temperature and the nature of the oxygen feed gas (air or pure oxygen). Moreover, the influence of the deposition of a catalytic activation layer (17 mu m thick) made of BSCF on top of the thin gastight layer was investigated. As a result of this parametric study, unpreceded oxygen flux values were achieved, i.e., a maximum flux of 67.7 ml(STP) min(-1) cm(-2) was obtained at 1000 degrees C using pure oxygen as the feed and argon as the sweep, while a flux of 12.2 ml(STP) min(-1) cm(-2) at 1000 degrees C was obtained when air was used as the feed. (C) 2011 Elsevier BM. All rights reserved., Financial support from the Spanish Ministry for Science and Innovation (Project ENE2008-06302 and FPI Grant JAE-Pre 08-0058), EU through FP7 NASA-OTM Project (NMP3-SL-2009-228701), and the Helmholtz Association of German Research Centres through the Helmholtz Alliance MEM-BRAIN (Initiative and Networking Fund) is kindly acknowledged. Mrs H. Burlet has contributed to this work with the careful revision of the English language.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Fluid Dynamic Modeling of Oxygen Permeation through Mixed Ionic-Electronic Conducting Membranes

  • Gozálvez-Zafrilla, José M.|||0000-0003-4419-6765
  • Santafé Moros, María Asunción|||0000-0002-0933-108X
  • Escolástico Rozalén, Sonia|||0000-0002-7097-2425
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] The oxygen transport in a lab-scale experimental set-up for permeation testing of oxygen transport membranes has been modeled using computational fluid dynamics using Finite Element Analysis. The modeling considered gas hydrodynamics and oxygen diffusion in the gas phase and vacancy diffusion of oxygen in a perovskite disc-shaped membrane at 1273. K. In a first step, the model allowed obtaining the coefficient diffusion of oxygen. The parametric study showed that the set-up geometry and flow rate in the air compartment did not have major influence in the oxygen transport. However, very important polarization effects in the sweep-gas (argon) compartment were identified. The highest oxygen permeation flux and the lowest oxygen concentration on the membrane surface were obtained for the following conditions (in increasing order of importance): (1) a large gas inlet radius; (2) short gas inlet distance; and (3) a high gas flow rate. © 2011 Elsevier B.V., The Spanish Ministry for Science and Innovation (JAE-Pre 08-0058 grant and ENE2008-06302 project) and through FP7 NASA-OTM Project (NMP3-SL-2009-228701) is kindly acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Rare Earth-doped Ceria Catalysts for ODHE Reaction in a Catalytic Modified MIEC Membrane Reactor

  • Lobera González, Maria Pilar
  • García Fayos, Julio
  • Balaguer Ramirez, Maria|||0000-0002-7098-9235
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] An intensification process for the selective oxidation of hydrocarbons integrates a catalytic reactor and an oxygen separation membrane. This work presents the study of oxidative dehydrogenation of ethane at 1123 K in a catalytic membrane reactor based on mixed ionic-electronic conducting (MIEC) membranes. The surface of a membrane made of Ba0.5Sr0.5Co0.8Fe0.2O3-d has been activated using different porous catalytic layers based on rare earth-doped cerias (fluorite structure) and the porous catalytic coating was deposited by screen printing (coating around 15 mu m). The different catalyst formulations were developed by partial substitution of Ce and were synthesized by co-precipitation followed by cobalt impregnation when required. Specifically, seven different catalysts based on the system Ce1-xLnxO2-d (x=0.1 or 0.2; Ln=Tb, Pr, Er, Gd, and Tb+Er), including the effect of cobalt addition (2?% molar) in Ce0.8Tb0.2O2-d, were studied. The ceria catalysts were studied by XRD, SEM, DC-conductivity as a function of oxygen partial pressure, and the high-temperature stability in a CO2 environment was assessed using thermogravimetry. Then, the influence of the ceria catalytic coating on the oxygen permeation flux through the MIEC membrane was studied using argon and methane as the sweep gas in the permeate side. Finally, oxidative dehydrogenation of ethane reaction tests were performed at 1123 K, as a function of the ethane concentration in the feed. The use of a disk-shaped membrane in the reactor made it possible to prevent the direct contact of gaseous oxygen and hydrocarbons and thus to increase the ethylene yield. High ethylene yields (up to approximate to 84?%) were obtained using a catalytic coating based on 20?% Tb-doped ceria including macropores produced by the addition of graphite platelets in the screen printing ink. The high yields obtained in this kind of catalytic membrane are attributed to the combination of: the high catalytic activity; the control of the oxygen concentration in the gas phase (reaction chamber); and the appropriate fluid dynamics, enabling the fast ethylene evacuation., Financial support by the Spanish Ministry for Science and Innovation (ENE2011-24761 FPI BES-2009-015835 grants), EU through FP7 NASA-OTM Project (NMP3-SL-2009-228701), and the Helmholtz Association of German Research Centres through the Helmholtz Alliance MEM-BRAIN (Initiative and Networking Fund) is kindly acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Oxygen permeation studies in surface Pd-activated asymmetric Ce0.9Gd0.1O1.95 membranes for application in CO2 and CH4 environments

  • García-Fayos, Julio
  • Sogaard, Martin
  • Kaiser, Andreas
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] Oxygen Transport Membranes (OTMs) present a high potential for being considered in the integration of O-2 supply systems in oxyfuel installations, as well as for the conduction of chemical reactions when operating Catalytic Membrane Reactors (CMRs). Several solutions are being prospected for overcoming the main drawbacks regarding materials stability and membrane performance. A highly stable material such as Ce0.9Gd0.1O1.95(CGO) doped with 2% mol. Co was studied as a 40 mu m-thick CGO supported CGO membrane. This membrane was characterized by studying its performance as oxygen permeation membrane for the production of oxygen under oxyfuel conditions and for the conduction of chemical reactions involving CH4. In order to improve oxygen surface reactions and consequently, the oxygen permeation, the membrane was surface activated with the addition of Pd nanoparticles. A broad characterization consisting of the study of O-2 production under different environments simulating real application conditions was conducted by subjecting the membrane to Ar, CO2 and CH4 environments in the temperature range of 750 to 1000 degrees C. A peak oxygen flux of 7.8 ml.min(-1)cm(-2) was obtained at 1000 degrees C when using a sweep consisting of 75% CH4 in Ar. This flux corresponds to a 16-fold improvement in the O-2 permeation at 1000 degrees C when sweeping with Ar, with an oxygen flux of 0.47 ml.min(-1).cm(-2). An oxygen flux of 1.2 ml.min(-1).cm(-2) was obtained at 1000 degrees C when feeding with pO(2) = 1 atm in feed side. Membrane performance under CO2-containing environments showed a positive effect of CO2 on permeation at 1000-900 degrees C, reaching up to 0.59 ml.min(-1).cm(-2) O-2 at 1000 degrees C. A continuous exposure of CO2 during 48 h at 750 degrees C resulted in a slight J(O-2) increase, with a reversible reduction in performance when returning to clean conditions, thus demonstrating high stability of CGO membranes., Financial support by the Spanish Ministry for Science and Innovation (Project ENE2008-06302) and by the EU through FP7 NASA-OTM Project (NMP3-SL-2009- 228701) is kindly acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Optimization of ODHE membrane reactor based on mixed ionic electronicconductor using soft computing techniques

  • Lobera González, Maria Pilar
  • Valero Cubas, Soledad|||0000-0003-4565-326X
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
  • Escolástico Rozalén, Sonia|||0000-0002-7097-2425
  • Argente, Estefanía|||0000-0002-5431-3868
  • Botti V.|||0000-0002-6507-2756
[EN] This work presents the optimization of the operating conditions of a membrane reactor for the oxidative dehydrogenation of ethane. The catalytic membrane reactor is based on a mixed ionic-electronic conducting material, i.e. Ba(0.5)Sr(0.5)Co(0.8)Fe(0.2)O(delta-3), which presents high oxygen flux above 750 degrees C under sufficient chemical potential gradient. Specifically, diluted ethane is fed into the reactor chamber and air (or diluted air) is flushed to the other side of the membrane. A framework based on Soft Computing techniques has been used to maximize the ethylene yield by simultaneously varying five operation variables: nominal reactor temperature (Temp); gas flow in the reaction compartment (QHC); gas flow in the oxygen-rich compartment (QAir); ethane concentration in the reaction compartment (%C(2)H(6)); and oxygen concentration in oxygen-rich compartment (%O(2)). The optimization tool combines a genetic algorithm guided by a neural network model. This shows how the neural network model for this particular problem is obtained and the analysis of its behavior along the optimization process. The optimization process is analyzed in terms of: (1) catalytic figures of merit, i.e., evolution of yield and selectivity towards different products and (2) framework behavior and variable significance. The two experimental areas maximizing the ethylene yield are explored and analyzed. The highest yield reached in the optimization process exceeded 87%. (C) 2010 Elsevier Ltd. All rights reserved., Financial support from the Spanish Ministry for Science and Innovation (Project ENE2008-06302 and FPI Grant JAE-Pre 08-0058, CONSOLIDER-INGENIO 2010 under grant CSD2007-00022, TIN2008-04446/TIN project and TIN2009-13839-C03-01 project, which are co-funded by the Spanish government and FEDER funds), EU through FP7 NASA-OTM Project (NMP3-SL-2009-228701), and the Helmholtz Association of German Research Centers through the Helmholtz Alliance MEM-BRAIN (Initiative and Networking Fund) is kindly acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

On the Use of Supported Ceria Membranes for Oxyfuel process / Syngas production

  • Lobera González, Maria Pilar
  • Foghmoes, Soren P.
  • Søgaard, Martin
  • Kaiser, Andreas
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] Ceramic oxygen transport membranes (OTMs) enable selective oxygen separation from air at high temperatures. Among several potential applications for OTMs, the use in (1) oxygen production for oxyfuel power plants and (2) the integration in high-temperature catalytic membrane reactors for alkane upgrading through selective oxidative reactions are of special interest. Nevertheless, these applications involve the direct contact of the membrane surface with carbon-rich atmospheres. Most state-of-the-art permeable membranes are based on perovskites, which are prone to carbonation under operation in CO2-rich environments and/or decomposition in reducing gas environments. The oxygen flux through supported thin film membranes of Ce-0.9Gd0.1O1.95-delta (CGO) with 2 mol.% of cobalt was measured for oxygen separation in oxyfuel processes and in syngas production and degradation was compared to perovskite membranes. The CGO membranes consist of a 27 mu m-thick gastight CGO layer supported on a porous CGO substrate. The flat surface of the membrane was coated using two different porous catalytic layers aiming to improve the oxygen activation rate on the permeate side while the porous substrate was infiltrated with an oxygen reduction catalyst. Oxygen separation was studied using air as feed and argon/CO2 or argon/CH4 mixtures as sweep gas in the temperature range 750-1000 degrees C. The supported membrane exhibited a maximum oxygen flux of ca. 5 ml min(-1) cm(-2) at 1000 degrees C when diluted methane was used as sweep gas. The CGO membrane showed high stability in CO2 (in contrast to tests on La0.6Sr0.4Co0.2Fe0.8O3-delta (LSCF) membranes) and no detrimental effect on the oxygen flux is observed when CO2 is present in the sweep gas even at temperatures below 800 degrees C. Moreover, the SEM analysis showed that membrane integrity remained stable after the permeation tests using CO2. (C) 2011 Elsevier B. V. All rights reserved., Financial support by the Spanish Ministry for Science and Innovation (Project ENE2008-06302) and by the EU through FP7 NASA-OTM Project (NMP3-SL-2009-228701) is kindly acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

High Ethylene Production through ODHE Membrane Reactors based on Fast Oxygen-Ion Conductors

  • Lobera González, Maria Pilar
  • Escolástico Rozalén, Sonia|||0000-0002-7097-2425
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] High ethylene productivity through the oxidative dehydrogenation of ethane has been achieved in a catalytic membrane reactor based on a highly solid-state oxygen permeable material (Ba0.5Sr0.5Co0.8Fe0.2O3 d). Ethylene is selectively produced by avoiding the direct contact of molecular oxygen and hydrocarbons, thereby minimizing the oxygen concentration in the reaction side. Another key aspect in the process is the dilution of ethane in the feed to achieve high ethylene yields. There exists a specific combination of the ethane concentration and feed flow that maximizes ethylene productivity, whereas the diluting gas nature has a direct impact on the formation of higher olefins and coking issues. Indeed, the use of methane as an almost-inert dilutant allows the reduction of oligomerization and aromatization of the formed ethylene and therefore improves the reactor stability even at operating temperatures from 800 to 900 8C. This behavior is attributed to the competitive adsorption of methane and ethane/ethylene, the modification of the radical-driven homogeneous reaction, and the change of partially reducible membrane surface. The productivity values achieved at 8508C were 383 mLmin 1cm 2 for Ar and 353 mLmin 1cm 2 for CH4, with a selectivity of 80 and 90%, respectively, Financial support by the Spanish Ministry for Science and Innovation (Project ENE2008-06302 and FPI Grant JAE-Pre 08-0058), the European Union through FP7 NASA-OTM Project (NMP3-SL-2009228701), and the Helmholtz Association of German Research Centres through the Helmholtz Alliance MEM-BRAIN (Initiative and Networking Fund) is kindly acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Ethylene Production by ODHE in Catalytic Modified Ba0.5Sr0.5Co0.8Fe0.2O3 Membrane Reactors

  • Lobera González, Maria Pilar
  • García Fayos, Julio
  • Escolástico Rozalén, Sonia|||0000-0002-7097-2425
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] Process intensification by the integration of membranes and high-temperature reactors offers several advantages with regard to conventional process schemes, that is, energy saving, safe operation, reduced plant/unit size, and higher process performance, for example, higher productivity, catalytic activity, selectivity, or stability. We present the study of oxidative dehydrogenation of ethane at 850 8C on a catalytic membrane reactor based on a mixed ionic¿electronic conducting membrane. The surface of the membrane made of Ba0.5Sr0.5Co0.8Fe0.2O3 d has been activated by using different porous catalytic layers based on perovskites. The layer was deposited by screen printing, and the porosity and thickness was studied for the catalyst composition. The different catalyst formulations are based on partial substitution of A- and B-site atoms of doped strontium ferrite/cobaltites (A0.6Sr0.4Co0.5Fe0.5O3 d and Ba0.6Sr0.4BO3 d) and were synthesized by an ethylenediaminetetraacetic acid¿citrate complexation route. The use of a disk-shaped membrane in the reactor enabled the direct contact of gaseous oxygen and hydrocarbons to be avoided, and thus, the ethylene content increased. High ethylene yields (up to 81%) were obtained by using a catalytic coating based on Ba0.5Sr0.5Co0.8Fe0.2O3 d, which included macropores produced by the addition of graphite platelets into the screen-printing ink. The promising catalytic results obtained with this catalytically modified membrane reactor are attributed to the combination of 1) the high activity, as a result of the high temperature and oxygen species diffusing through the membrane; 2) the control of oxygen dosing and the low concentration of molecules in the gas phase; and 3) suitable fluid dynamics, which enables appropriate feed contact with the membrane and the rapid removal of products., Financial support by the Spanish Ministry for Science and Innovation (Project ENE2008-06302, ENE2011-24761 and FPI Grant JAE-Pre 08-0058), the EU through the FP7 NASA-OTM Project (NMP3-SL-2009-228701), and the Helmholtz Association of German Research Centres through the Helmholtz Alliance MEM-BRAIN (Initiative and Networking Fund) is kindly acknowledged. We thank S. Jimenez for material preparation, M. Fabuel for TPD experiments, and Forschungszentrum Julich for SEM analysis of BSCF catalytic layer.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Study of CO2 stability and electrochemical oxygen activation of mixed conductors with low thermal expansion coefficient based on the TbBaCo3ZnO7+δ system

  • Vert Belenguer, Vicente Bernardo
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] The influence of different application-oriented factors on the electrochemical activity and stability of TbBaCo3ZnO7+delta when used as a solid oxide fuel cell cathode has been studied. Calcination at temperatures above 900 degrees C (e.g. 1000 degrees C) leads to a significant increase in the electrode polarization resistance. The effect of the sintering temperature of the TbBaCo3ZnO7+delta cathode seems to be more important than the effect produced by the Tb substitution as observed when compared with 900 degrees C-sintered YBaCo3ZnO7+delta; and ErBaCo3ZnO7+delta electrode performances. The presence of CO2 in the air flow leads to an increase of roughly 10% in the polarization resistance for the whole studied temperature range (500-850 degrees C) while this effect is reversible. Analysis of the impedance spectroscopy measurements shows that the exchange rate constant (k(G) from Gerischer element) is significantly affected by CO2 at temperatures below 700 degrees C, while the diffusion coefficient related parameter is slightly influenced at low temperatures. Electrode degrades with a low constant rate of 1 m Omega cm(2) h(-1) after 60h. This cathode material exhibits high CO2 tolerance, as shown by temperature programmed treatment under a continuous gas flow of air with 5% CO2, and a relatively low thermal expansion coefficient., Financial support by the Universitat Politecnica de Valencia (Grant UPV-2007-06), the Spanish Ministry for Science and Innovation (Project ENE2008-06302), the EU through FP7 NASA-OTM Project (NMP3-SL-2009-228701), and the Helmholtz Association of German Research Centres through the Helmholtz Alliance MEM-BRAIN (Initiative and Networking Fund) is kindly acknowledged. The revision of this paper was funded by the Politecnica de Valencia. The authors wish to thank S. Jimenez for material preparation.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Oxygen permeation through tape-cast asymmetric all-La0.6Sr0.4Co0.2Fe0.8O3 (-) (delta) membranes

  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
  • García Fayos, Julio
  • Baumann, S.
  • Schulze-Kueppers, F.
  • Meulenberg, W. A.
[EN] One of the most promising materials for oxygen separation amongst ceramic oxygen transport membranes (OTMs) is La0.6Sr0.4Co0.2Fe0.8O3 (-delta) (LSCF) due to its relatively high oxygen permeability combined with high stability. In this work, asymmetric thin-film LSCF membranes supported over a porous LSCF support were manufactured by inverse sequential tape casting. Moreover, surface activation was accomplished by depositing a porous LSCF activation layer in order to promote oxygen evolution reaction, i.e. O2- to O-2 oxidation, in the permeate membrane side. In this case, the porous layer allows the surface area available for oxygen activation to be enlarged. Both the manufacturing of the asymmetric thin-film membranes and the surface activation are described in detail. A thorough study of the oxygen permeation is presented for disk-shaped 30 mu m thick LSCF-supported membranes considering the following operating parameters: temperature (1000-600 degrees C), sweep flow rate (300-750 ml min(-1) argon) and oxygen partial pressure in the feed (0.21-1 atm). High permeation fluxes were achieved, e.g., 11.87 ml min(-1) cm(-2) at 1000 degrees C and 300 ml min(-1) argon sweep when using pure oxygen as feed. A change in the apparent activation energy at about 850 degrees C was related to a reversible structural change in the perovskite symmetry (cubic <-> rhombohedral), as revealed by XRD measurements. Furthermore, the application of an activation layer allowed the permeation process to be improved, especially at low temperatures, i.e. below 800 degrees C. Specifically, an improvement of up to about 300% at 600 degrees C is observed upon application of the activation layer. The activated membrane reached a flux of 13.3 ml min(-1) cm(-2) at 1000 degrees C under an O-2/Ar gradient. Additional permeation tests using CO2-rich sweep gas demonstrated the good stability and performance of these LSCF asymmetric membranes at 900 and 1000 degrees C. (c) 2013 Elsevier B.V. All rights reserved., Financial support by the Spanish Ministry for Science and Innovation (ENE2011-24761 and SEV-2012-0267 Grants), by the EU through FP7 NASA-OTM Project (NMP3-SL-2009-228701), and by the Helmholtz Association of German Research Centres through the Helmholtz Portfolio MEM-BRAIN is gratefully acknowledged. The authors would like to express their gratitude to Dr. W. Fischer for crystal structure analysis by X-ray diffraction. Mrs. J. Carter-Sigglow has contributed to this work with the careful revision of the English usage.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Quaternary mixture designs applied to the development of multi-element oxygen electrocatalysts based on the Ln(0.58)Sr(0.4)Fe(0.8)Co(0.2)O(3-delta) system (Ln = La1-x-y-zPrxSmyBaz): Predictive modeling approaches

  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
  • Vert Belenguer, Vicente Bernardo
[EN] The experimental data generated through the optimization of oxygen electrocatalysts based on the perovskite Ln(0.58)Sr(0.4)Fe(0.8)Co(0.2)O(3-delta) system (Ln = La1-x-y-zPrxSmyBaz) have been modeled following different approaches. The main application of these catalysts is as fuel cell (SOFC) cathodes and activation layers on oxygen-transport membranes. Among the different La, Pr and Sm combinations, those containing at a time Sm-La-Ba or alternatively Pr-La-Ba show the lowest polarization resistance values. Within the same substitution degree, Pr-Ba-based compositions have lower electrode resistance than samarium-based ones. The experimental datasets available for the series of materials can be divided into: composition data, structural data (X-ray diffraction patterns), and electrochemical characterization data (electrochemical impedance spectra). Electrochemical characterization was performed for each electrode composition as a function of the operating temperature and oxygen partial pressure. Different ways of reducing the dimensionality of the spectral descriptors (XRD patterns and impedance spectroscopy) were applied based on knowledge-guided and unsupervised approaches. Different material descriptors were studied as input variables in the modeling of the electrochemical properties. (C) 2010 Elsevier B.V. All rights reserved., Funding from Universitat Politècnica de València (grant UPV2007-06), the Spanish Ministry for Science and Innovation (Project ENE-2008-06302), the Helmholtz Association of German Research Centers through the Helmholtz Alliance MEM-BRAIN (Initiative and Networking Fund) and EU through FP7 NASA-OTM Project (NMP3-SL-2009-228701) is kindly acknowledged.