Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Manufacturing tolerance analysis of an MMI-Based 90 degrees optical hybrid for InP integrated coherent receivers

  • Sánchez Fandiño, Javier Antonio
  • P. Muñoz|||0000-0001-6026-1649
[EN] A numerical study of the impact that manufacturing tolerances have on the performance of an InP 4 × 4 MMI working as a 90° optical hybrid is presented, including simultaneous variations of width, thickness, and refractive index over the C and L bands. Simulation results for different figures of merit, such as optical common-mode rejection ratios (CMRRs) and phase errors, are provided for both nominal and worst case scenarios. Additionally, system simulations are performed to compute imbalance-induced power penalty. Our results indicate that the combined effect of realistic foundry tolerances on device performance is significant. In particular, a fourfold reduction is predicted between nominal (≃40 nm) and worst cases (≃10 nm) when optical CMRRs and phase errors are compared against Optical Internetworking Forum specifications. By contrast, a much greater bandwidth is expected at the system level (≥ 40 nm) if a power penalty of less than 1 dB (@BER = 10-3) is to be allowed. In fact, worst case power penalties lower than 0.25 dB are predicted over the full C band, which further proves the great potential of integrated 4 × 4 MMIs as wide-bandwidth devices for mass production of coherent receivers using state-of-the-art integration technologies., This work was supported in part by the Spanish MICINN Project TEC2010-21337, acronym ATOMIC, and in part by projects FEDER UPVOV10-3E-492 and UPVOV08-3E-008. The work of J. S. Fandin˜o was supported by Grant FPU-2010 (ref: AP2010-1595). The authors are also grateful to the EuroPIC consortium (FP7 funded programme NMP 228839-2) for access to the design manual and design toolkit of the generic InP fab.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Integrated InP frequency discriminator for Phase-modulated microwave photonic links

  • Sánchez Fandiño, Javier Antonio
  • Doménech Gómez, José David
  • P. Muñoz|||0000-0001-6026-1649
  • Capmany Francoy, José|||0000-0002-6460-4167
[EN] We report the design, fabrication and characterization of an integrated frequency discriminator on InP technology for microwave photonic phase modulated links. The optical chip is, to the best of our knowledge, the first reported in an active platform and the first to include the optical detectors. The discriminator, designed as a linear filter in intensity, features preliminary SFDR values the range between 67 and 79 dB.Hz2/3 for signal frequencies in the range of 5-9 GHz limited, in principle, by the high value of the optical losses arising from the use of several free space coupling devices in our experimental setup. As discussed, these losses can be readily reduced by the use of integrated spot-size converters improving the SFDR by 17.3 dB (84-96 dB.Hz2/3). Further increase up to a range of (104-116 dB.Hz2/3) is possible by reducing the system noise eliminating the EDFA employed in the setup and using a commercially available laser source providing higher output power and lower relative intensity noise. Other paths for improvement requiring a filter redesign to be linear in the optical field are also discussed., The authors wish to acknowledge the financial support given by the Research Excellency Award Program GVA PROMETEO 2008/092, Spanish MICINN Project TEC2010-21337, acronym ATOMIC; project FEDER UPVOV10-3E-492 and project FEDER UPVOV08-3E008. J.S. Fandiño acknowledges financial support through grant FPU-2010 (ref: AP2010- 1595). J. D. Doménech acknowledges both Beca de Formacion de Personal Investigador (FPI) research grant (ref: BES-2009-018381) and funding from Intel Doctoral Student Honor Programme. The authors are also grateful to the EuroPIC consortium (FP7 funded programme NMP 228839-2) for access to the design manual and design toolkit of the generic InP fab