Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Manufacturing tolerance analysis of an MMI-Based 90 degrees optical hybrid for InP integrated coherent receivers

  • Sánchez Fandiño, Javier Antonio
  • P. Muñoz|||0000-0001-6026-1649
[EN] A numerical study of the impact that manufacturing tolerances have on the performance of an InP 4 × 4 MMI working as a 90° optical hybrid is presented, including simultaneous variations of width, thickness, and refractive index over the C and L bands. Simulation results for different figures of merit, such as optical common-mode rejection ratios (CMRRs) and phase errors, are provided for both nominal and worst case scenarios. Additionally, system simulations are performed to compute imbalance-induced power penalty. Our results indicate that the combined effect of realistic foundry tolerances on device performance is significant. In particular, a fourfold reduction is predicted between nominal (≃40 nm) and worst cases (≃10 nm) when optical CMRRs and phase errors are compared against Optical Internetworking Forum specifications. By contrast, a much greater bandwidth is expected at the system level (≥ 40 nm) if a power penalty of less than 1 dB (@BER = 10-3) is to be allowed. In fact, worst case power penalties lower than 0.25 dB are predicted over the full C band, which further proves the great potential of integrated 4 × 4 MMIs as wide-bandwidth devices for mass production of coherent receivers using state-of-the-art integration technologies., This work was supported in part by the Spanish MICINN Project TEC2010-21337, acronym ATOMIC, and in part by projects FEDER UPVOV10-3E-492 and UPVOV08-3E-008. The work of J. S. Fandin˜o was supported by Grant FPU-2010 (ref: AP2010-1595). The authors are also grateful to the EuroPIC consortium (FP7 funded programme NMP 228839-2) for access to the design manual and design toolkit of the generic InP fab.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A monolithic integrated photonic microwave filter

  • Sanchez Fandiño, Javier Antonio
  • Doménech Gómez, José David
  • P. Muñoz|||0000-0001-6026-1649
  • Capmany Francoy, José|||0000-0002-6460-4167
[EN] Meeting the increasing demand for capacity in wireless networks requires the harnessing of higher regions in the radiofrequency spectrum, reducing cell size, as well as more compact, agile and power-efficient base stations that are capable of smoothly interfacing the radio and fibre segments. Fully functional microwave photonic chips are promising candidates in attempts to meet these goals. In recent years, many integrated microwave photonic chips have been reported in different technologies. To the best of our knowledge, none has monolithically integrated all the main active and passive optoelectronic components. Here, we report the first demonstration of a tunable microwave photonics filter that is monolithically integrated into an indium phosphide chip. The reconfigurable radiofrequency photonic filter includes all the necessary elements (for example, lasers, modulators and photodetectors), and its response can be tuned by means of control electric currents. This is an important step in demonstrating the feasibility of integrated and programmable microwave photonic processors., The authors acknowledge financial support from the Spanish Centro para el Desarrollo Tecnologico Industrial (CDTI) through the NEOTEC start-up programme, the European Commission through the 7th Research Framework Programme project, Photonic Advanced Research and Development for Integrated Generic Manufacturing (FP7-PARADIGM), the Generalitat Valenciana through the Programa para grupos de Investigacion de Excelencia (PROMETEO) project code 2013/012, the Spanish Ministerio de Economia y Comercio (MINECO) via project TEC2013-42332-P, PIF4ESP, and the Unwersitat Politecnica de Valencia (UPVOV) through projects 10-3E-492 and 08-3E-008 funded by the Fondos Europeos de Desarrollo Regional (FEDER). J.S. Fandino acknowledges financial support from Formacion de Profesorado Universitario (FPU) grant AP2010-1595.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Integrated InP frequency discriminator for Phase-modulated microwave photonic links

  • Sánchez Fandiño, Javier Antonio
  • Doménech Gómez, José David
  • P. Muñoz|||0000-0001-6026-1649
  • Capmany Francoy, José|||0000-0002-6460-4167
[EN] We report the design, fabrication and characterization of an integrated frequency discriminator on InP technology for microwave photonic phase modulated links. The optical chip is, to the best of our knowledge, the first reported in an active platform and the first to include the optical detectors. The discriminator, designed as a linear filter in intensity, features preliminary SFDR values the range between 67 and 79 dB.Hz2/3 for signal frequencies in the range of 5-9 GHz limited, in principle, by the high value of the optical losses arising from the use of several free space coupling devices in our experimental setup. As discussed, these losses can be readily reduced by the use of integrated spot-size converters improving the SFDR by 17.3 dB (84-96 dB.Hz2/3). Further increase up to a range of (104-116 dB.Hz2/3) is possible by reducing the system noise eliminating the EDFA employed in the setup and using a commercially available laser source providing higher output power and lower relative intensity noise. Other paths for improvement requiring a filter redesign to be linear in the optical field are also discussed., The authors wish to acknowledge the financial support given by the Research Excellency Award Program GVA PROMETEO 2008/092, Spanish MICINN Project TEC2010-21337, acronym ATOMIC; project FEDER UPVOV10-3E-492 and project FEDER UPVOV08-3E008. J.S. Fandiño acknowledges financial support through grant FPU-2010 (ref: AP2010- 1595). J. D. Doménech acknowledges both Beca de Formacion de Personal Investigador (FPI) research grant (ref: BES-2009-018381) and funding from Intel Doctoral Student Honor Programme. The authors are also grateful to the EuroPIC consortium (FP7 funded programme NMP 228839-2) for access to the design manual and design toolkit of the generic InP fab
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Silicon opto-electronic wavelength tracker based on an asymmetric 2x3 Mach-Zehnder Interferometer

  • Doménech Gómez, José David
  • Sánchez Fandiño, Javier Antonio
  • Gargallo Jaquotot, Bernardo Andrés
  • Baños López, Rocío
  • P. Muñoz|||0000-0001-6026-1649
[EN] In this paper we report on the experimental demonstration of a Silicon-on-Insulator opto-electronic wavelength tracker for the optical telecommunication C-band. The device consist of a 2x3 Mach-Zehnder Interferometer (MZI) with 10 pm resolution and photo-detectors integrated on the same chip. The MZI is built interconnecting two Multimode Interference (MMI) couplers with two waveguides whose length difference is 56 mm. The first MMI has a coupling ratio of 95:05 to compensate for the propagation loss difference corresponding to the 56 mm. The wavelength tracker design provides three complementary, with 120◦ phase relations, responses. The MZI optical responses exhibit rejection as good as 15 dB, thanks to asymmetric design for the input coupler. Synchronized recorded DC electronic responses for the three photo-detector outputs reproduce the MZI de-phased characteristic, allowing for monitoring wavelength changes with sign., The authors acknowledge financial support by the Spanish CDTI NEOTEC start-up programme, the Spanish MICINN project TEC2010-21337, acronym ATOMIC, the Spanish MINECO project TEC2013-42332-P, acronym PIC4ESP, project FEDER UPVOV 10-3E-492 and project FEDER UPVOV 08-3E-008. B. Gargallo acknowledges financial support through FPI grant BES-2011-046100. J.S. Fandiño acknowledge financial support through FPU grant AP2010-1595.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Arbitrary Coupling Ratio Multimode Interference Couplers in Silicon-on-Insulator

  • Doménech Gómez, José David
  • Sánchez Fandiño, Javier Antonio
  • Gargallo Jaquotot, Bernardo Andrés
  • P. Muñoz|||0000-0001-6026-1649
In this paper, we present the design, manufacturing, characterization, and analysis of the coupling ratio spectral response for multimode interference couplers in silicon-on-insulator (SOI) technology. The couplers were designed using a Si rib waveguide with SiO2 cladding, on a regular 220 nm film and 2 μm buried oxide SOI wafer. A set of eight different designs, three canonical and five using a widened/narrowed coupler body, have been subject of study, with coupling ratios 50:50, 85:15, and 72:28 for the former, and 95:05, 85:15, 75:25, 65:35, and 55:45 for the latter. Two wafers of devices were fabricated, using two different etch depths for the rib waveguides. A set of six dies, three per wafer, whose line metrology matched the design, were retained for characterization. The coupling ratios obtained in the experimental results match, with little deviations, the design targets for a wavelength range between 1525 and 1575 nm, as inferred from spectral measurements and statistical analyses. Excess loss for all the devices is conservatively estimated to be approximately 0.6 dB in average. All the design parameters, body width and length, input/output positions and widths, and tapers dimensions are disclosed for reference., This work was supported by the Spanish CDTI NEOTEC start-up program, the Spanish MICINN project TEC2010-21337, acronym ATOMIC, the Spanish MINECO project TEC2013-42332-P, acronym PIC4ESP, project FEDER UPVOV 10-3E-492, and project FEDER UPVOV 08-3E-008. The work of B. Gargallo was supported by FPI under Grant BES-2011-046100. The work of J.S. Fandino was supported by FPU under grant AP2010-1595.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Analysis of System Imperfections in a Photonics-Assisted Instantaneous Frequency Measurement Receiver Based on a Dual-Sideband Suppressed-Carrier Modulation

  • Sánchez Fandiño, Javier Antonio
  • P. Muñoz|||0000-0001-6026-1649
[EN] Instantaneous frequency measurement receivers are a well-established technology that is used for the ultrafast characterization of pulsed microwave signals over a broad bandwidth. Recently, numerous photonic approaches to instantaneous frequency measurement (IFM) have been proposed and experimentally demonstrated, with the ultimate aim of leveraging the benefits of optical technology to improve the performance of already existent electronic solutions. Despite the numerous results, not so much attention has been paid so far to understand the subtle implications that system imperfections can have on realistic photonics-based IFM receivers. Here, we focus our attention on one of the most promising among these IFM techniques, which is based on optical power monitoring of a dual-sideband suppressed-carrier modulation after a Mach Zehnder interferometer (MZI) filter. We develop a time-domain model for the rigorous analysis of all major optical and electrical effects, including amplitude imbalance and phase errors in the modulator and the MZI, as well as on-pulse RF phase/frequency modulation. Simulations are then used to illustrate the substantial effect that a nonperfectly suppressed optical carrier can have on system performance. More importantly, it is shown that in a nonideal situation, the system amplitude comparison function critically depends on input RF power, thus greatly limiting the dynamic range of the photonics-based receiver. Some approaches to solve these issues are also discussed., This work was supported by projects TEC2010-21337 (ATOMIC), FEDER UPVOV10-3E-492, FEDER UPVOV08-3E-008, TEC2013-42332-P (PIC4ESP), and PROMETEO 2013/012. The work of J. S. Fandino was supported by Grant FPU-2010 (ref: AP2010-1595).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Photonics-based microwave frequency measurement using a double-sideband suppressed-carrier modulation and an InP integrated ring-assisted Mach Zehnder interferometer filter

  • Sánchez Fandiño, Javier Antonio
  • P. Muñoz|||0000-0001-6026-1649
[EN] A photonic system capable of estimating the unknown frequency of a CW microwave tone is presented. The core of the system is a complementary optical filter monolithically integrated in InP, consisting of a ring-assisted Mach-Zehnder interferometer with a second-order elliptic response. By simultaneously measuring the different optical powers produced by a double-sideband suppressed-carrier modulation at the outputs of the photonic integrated circuit, an amplitude comparison function that depends on the input tone frequency is obtained. Using this technique, a frequency measurement range of 10 GHz (5-15 GHz) with a root mean square value of frequency error lower than 200 MHz is experimentally demonstrated. Moreover, simulations showing the impact of a residual optical carrier on system performance are also provided. (C) 2013 Optical Society of America, This work was supported by projects TEC2010-21337 (ATOMIC), FEDER UPVOV10-3E-492, and UPVOV08-3E-008. J. S. Fandino was supported by grant FPU-2010 (ref: AP2010-1595). The authors acknowledge the use of Phoenix Software tools for design of the InP PIC, which was manufactured within the EuroPIC FP7 project (ref: NMP 228839-2).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Two-port multimode interference reflectors based on aluminium mirrors in a thick SOI platform

  • Sánchez Fandiño, Javier Antonio
  • Doménech Gómez, José David
  • P. Muñoz|||0000-0001-6026-1649
Multimode interference reflectors (MIRs) were recently introduced as a new type of photonic integrated devices for on-chip, broadband light reflection. In the original proposal, different MIRs were demonstrated based on total internal reflection mirrors made of two deep-etched facets. Although simpler to fabricate, this approach imposes certain limits on the shape of the field pattern at the reflecting facets, which in turn restricts the types of MIRs that can be implemented. In this work, we propose and experimentally demonstrate the use of aluminium-based mirrors for the design of 2-port MIRs with variable reflectivity. These mirrors do not impose any restrictions on the incident field, and thus give more flexibility at the design stage. Devices with different reflectivities in the range between 0 and 0.5 were fabricated in a 3 um thick SOI platform, and characterization of multiple dies was performed to extract statistical data about their performance. Our measurements show that, on average, losses both in the aluminium mirror and in the access waveguides reduce the reflectivities to about 79% of their target value. Moreover, standard deviations lower than +/- 5% are obtained over a 20 nm wavelength range (1540-1560 nm). We also provide a theoretical model of the aluminium mirror based on the effective index method and Fresnel equations in multilayer thin films, which shows good agreement with FDTD simulations., This work was supported by projects TEC2010-21337 (ATOMIC), FEDER UPVOV10-3E-492, FEDER UPVOV08-3E-008, TEC2013-42332-P (PIC4ESP), and PROMETEO 2013/012. The work of J. S. Fandino was supported by Grant FPU-2010 (ref: AP2010-1595).