Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Comparative study of shortening and cutting strategies of single-walled and multi-walled carbon nanotubes assessed by scanning electron microscopy

  • Kierkowicz, Magdalena
  • Pach, Elzbieta
  • Santidrián, Ana
  • Sandoval, Stefania
  • Gonçalves, Gil
  • Tobías Rossell, Ester
  • Kalbáč, Martin
  • Ballesteros, Belén
  • Tobias, Gerard
Short carbon nanotubes (CNTs) are desired for a variety of applications. As a consequence, several strategies have been reported to cut and shorten the length of as-produced carbon nanotubes via chemical and physical routes. The efficiency of a given strategy largely depends on the physico-chemical characteristics of the CNTs employed. In order to be able to directly compare the advantages and disadvantages of commonly used protocols, a single batch of chemical vapor deposition single-walled CNTs (SWCNTs) and a batch of multi-walled CNTs (MWCNTs) were subjected to four cutting/shortening strategies, namely acid cutting, piranha treatment, steam shortening and ball milling. The length distribution was assessed by means of scanning electron microscopy. Sample purity and CNT wall structure were determined by Raman spectroscopy, thermogravimetric analysis and magnetic measurements. Within the employed experimental conditions, piranha treatment turned out to be the most efficient to achieve short SWCNTs with a narrow length distribution in a good yield, whereas a mixture of sulfuric/nitric acid was preferred in the case of MWCNTs. A subsequent short steam treatment allowed to remove functional groups present in the samples, leading to median length distributions of 266 nm and 225 nm for SWCNTs and MWCNTs respectively after the combined protocols., The research leading to these results has received funding from the People Programme (Marie Curie Actions) of the European Union's Seventh Framework Programme FP7/2007-2013/ under REA grant agreement n°290023 (RADDEL). We acknowledge financial support from Spanish Ministry of Economy and Competitiveness through the “Severo Ochoa” Programme for Centres of Excellence in R&D (SEV-2015-0496, ICMAB; SEV-2013-0295, ICN2), and CHALENG (MAT2014-53500-R). M. K. also acknowledges support from the project LL1301 (MEYS). The ICN2 is funded by the CERCA programme (Generalitat de Catalunya). G. G. gratefully acknowledges the funding by European Commission under individual fellowship Marie Sklodowska-Curie (NANOTER, Grant Agreement 708351).We are thankful to Guillaume Sauthier from ICN2 for the XPS measurements. The authors would like to thank Thomas Swan Co. Ltd. for providing Elicarb© carbon nanotubes used for this study., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Preparation and Characterization of Graphene Oxide Aerogels: Exploring the Limits of Supercritical CO2 Fabrication Methods

  • Borrás, Alejandro
  • Gonçalves, Gil
  • Marbán Calzón, Gregorio
  • Sandoval, Stefania
  • Pinto, Susana C.
  • Marques, Paula A.A.P.
  • Fraile, Julio
  • Tobias, Gerard
  • López Periago, Ana M.
  • Domingo, Concepción
The supercritical carbon dioxide synthesis of non-reduced graphene oxide (GO) aerogels from dispersions of GO in ethanol is here reported as a low-cost, efficient and environmentally friendly process. The preparation is carried out at the mild conditions of 333 K and 20 MPa. The high aspect ratio of the used GO sheets (ca. 30 μm lateral dimensions) allowed the preparation of aerogel monoliths by simultaneous scCO2 gelation and drying. Solid state characterization results indicate that a thermally stable mesoporous non-reduced GO aerogel was obtained by using the supercritical procedure, keeping the GO sheets most of the surface oxygenated groups, thus, facilitating further functionalization. Moreover, the monoliths have a very low density, high specific surface area and excellent mechanical integrity, characteristics which rivals with that of most light-weight reduced graphene aerogels reported in the literature., This work was financed by the Spanish National Plan of Research with projects CTQ2014-56324, CTQ2017-83632 and MAT2017-86616-R. C.D., G.T, A.B, G.G., S.S., J.F. and A.L.P. acknowledge the financial support from the Spanish MEC, through the Severo Ochoa Program for Centers of Excellence in R&D (SEV-2015-0496). This work (A.B.) has been done in the framework of the doctoral program "Chemistry" of the Universitat Autònoma de Barcelona. A.L.P. acknowledges the RyC-2012-11588 contract. A.B. acknowledges FPI grant. G.G. acknowledges the funding by EC H2020 under individual fellowship Marie Sklodowska-Curie (NANOTER, Grant Agreement 708351). P.M. and S.P. acknowledge the FCT/MCTES for respectively, a research contract under the Program Investigator (IF/00917/2013/ CP1162/CT0016) and PhD grant SFRH/BD/111515/2015; also UID/EMS/00481/2013-FCT and CENTRO-01-0145-FEDER-022083., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Selective two-photon absorption in carbon dots: a piece of the photoluminescence emission puzzle

  • Santos, Carla, I. M.
  • Mariz, Inês F. A.
  • Pinto, Sandra N.
  • Gonçalves, Gil
  • Bdikin, Igor
  • Marques, Paula A.A.P.
  • Neves, Maria da Graça P.M.S.
  • Martinho, José M. G.
  • Maçôas, Ermelinda M. S.
Carbon nanodots (Cdots) are now emerging as promising nonlinear fluorophores for applications in biological environments. A thorough and systematic approach to the two-photon induced emission of Cdots that could provide design guidelines to control their nonlinear emission properties is still missing. In this work, we address the nonlinear optical spectroscopy of Cdots prepared by controlled chemical cutting of graphene oxide (GO). The two-photon absorption in the 700–1000 nm region and the corresponding emission spectrum are carefully investigated. The highest two-photon absorption cross-section estimated was 130 GM at 720 nm. This value is comparable with the one reported for graphene nanoribbons with push–pull architecture. The emission spectrum depends on the excitation mode. At the same excitation energy, nonlinear excitation results in excitation-wavelength independent emission, while upon linear excitation the emission is excitation-wavelength dependent. The biphotonic interaction seems to be selective towards sp2 clusters bearing electron donor and acceptor groups found in push–pull architectures. Both linear and nonlinear emission can be understood based on the existence of isolated sp2 clusters involved in π–π stacking interactions with clusters in adjacent layers., The authors are grateful to Fundação para a Ciência e Tecnologia (FCT, Portugal), European Union, QREN, FEDER and COMPETE for funding the QOPNA, TEMA, and CQFM research unit (project Pest-C/QUI/UI0062/2013, UID/EMS/ 00481/2013 and UID/NAN/50024/2013). FCT is acknowledged for the Post-Doctoral grants of C. I. M. S., S. N. P and I. F. A. M., and for supporting the individual work contract of E. M., I. B. and P. A. A. P. M. within the Investigador FCT program (SFRH/BPD/105478/2014, SFRH/BPD/92409/2013, SFRH/BPD/ 75782/2011, IF/00759/2013, IF/00582/2015 and IF/00917/ 2013). G. G. gratefully acknowledges the funding by European Commission under individual fellowship Marie SklodowskaCurie (NANOTER, Grant Agreement 708351)., Peer reviewed
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Determination of the length of single-walled carbon nanotubes by scanning electron microscopy

  • Sandoval, Stefania|||0000-0002-0050-7501
  • Kierkowicz, Magdalena
  • Pach, Elzbieta|||0000-0001-9587-3768
  • Ballesteros, Belén|||0000-0002-1958-8911
  • Tobias, Gerard|||0000-0001-7116-2152
A methodology is presented to determine the length of well individualized single-walled carbon nanotubes (SWCNTs) by means of scanning electron microscopy (SEM). Accurate measurements on wide areas of the sample can be achieved in an easy, fast and trustworthy manner. We have tested several supports and solvents to optimize the dispersion of SWCNTs, as well as the SEM imaging conditions. The optimal methodology goes via dispersion of the sample in ortho-dichlorobenzene, deposition onto a continuous carbon film supported on a copper TEM grid, and SEM imaging at 2 kV in secondary electrons mode using a through-in-lens detector. • Individualization of SWCNTs is achieved by dispersion of SWCNTs in ortho-dichlorobenzene and deposition onto TEM grids• Individual SWCNTs are imaged by SEM• Length determination by SEM is as precise as AFM
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Comparative study of shortening and cutting strategies of single-walled and multi-walled carbon nanotubes assessed by scanning electron microscopy

  • Kierkowicz, Magdalena
  • Pach, Elzbieta|||0000-0001-9587-3768
  • Santidrián, Ana|||0000-0002-6964-4096
  • Sandoval, Stefania|||0000-0002-0050-7501
  • Gonçalves, Gil|||0000-0002-2302-9661
  • Tobías Rossell, Ester
  • Kalbáč, Martin|||0000-0001-9574-4368
  • Ballesteros, Belén|||0000-0002-1958-8911
  • Tobias, Gerard|||0000-0001-7116-2152
Short carbon nanotubes (CNTs) are desired for a variety of applications. As a consequence, several strategies have been reported to cut and shorten the length of as-produced CNTs via chemical and physical routes. The efficiency of a given strategy largely depends on the physico-chemical characteristics of the CNTs employed. In order to be able to directly compare the advantages and disadvantages of commonly used protocols, a single batch of chemical vapor deposition single-walled CNTs (SWCNTs) and a batch of multi-walled CNTs (MWCNTs) were subjected to four cutting/shortening strategies, namely acid cutting, piranha treatment, steam shortening and ball milling. The length distribution was assessed by means of scanning electron microscopy. Sample purity and CNT wall structure were determined by Raman spectroscopy, thermogravimetric analysis and magnetic measurements. Within the employed experimental conditions, piranha treatment turned out to be the most efficient to achieve short SWCNTs with a narrow length distribution in a good yield, whereas a mixture of sulfuric/nitric acid was preferred in the case of MWCNTs. A subsequent short steam treatment allowed to remove functional groups present in the samples, leading to median length distributions of 266 nm and 225 nm for SWCNTs and MWCNTs respectively after the combined protocols.