Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 14
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

The mOxy-CaL process: Integration of membrane separation, partial oxy-combustion and calcium looping for CO2 capture

  • Ortiz, Carlos
  • Valverde, Jose Manuel
  • Chacartegui, Ricardo
  • Romeo, Luis Miguel
  • Pérez-Maqueda, Luis A.
CO capture and storage (CCS) is considered as a key strategy in the short to medium term to mitigate global warming. The Calcium-Looping process, based on the reversible carbonation/calcination of CaO particles, is a promising technology for post-combustion CO capture because of the low cost and non-toxicity of natural CaO precursors and the minor energy penalty on the power plant in comparison with amines capture based technologies (4-9 % compared to 8-12 %). Another interesting process to reduce CO emissions in power plants is oxy-combustion, which is based on replacing the air used for combustion by a highly concentrated (~95 % v/v) O2 stream. This work proposes a novel process (mOxy-CaL) for post-combustion CO capture based on the integration of membrane separation, partial oxy-combustion and the Calcium-Looping process. An oxygenenriched air stream, which is obtained from air separation by using highly permeable polymeric membranes, is used to carry out partial oxy-combustion. The flue gas exiting partial oxy-combustion shows a CO concentration of ~30 % v/v (higher than 15 % v/v typical in coal power plants). After that, the flue gas is passed to the CaL process where the CO reacts with CaO solids according to the carbonation reaction. Thermogravimetric analysis show that the multicycle CaO conversion is enhanced as the CO concentration in the flue gas stream is increased. Process simulations show that the mOxy-CaL process has a high CO capture efficiency (~95%) with lower energy consumption per kg of CO avoided than previously proposed post-combustion CO capture technologies. Moreover, the overall system size is significantly lower that state-of-the-art CaL systems, which allows for an important reduction in the capital cost of the technology., The research leading to these results has received funding from the European Union's Horizon 2020 research and innovation program under grant agreement No 727348, project SOCRATCES.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Scaling-up the calcium-looping process for co2 capture and energy storage

  • Ortiz, Carlos
  • Valverde, José M.
  • Chacartegui, Ricardo
  • Pérez-Maqueda, Luis A.
  • Giménez-Gavarrell, Pau
The Calcium-Looping (CaL) process has emerged in the last years as a promising technology to face two key challenges within the future energy scenario: energy storage in renewable energy-based plants and CO capture from fossil fuel combustion. Based on the multicycle calcination-carbonation reaction of CaCO for both thermochemical energy storage and post-combustion CO capture applications, the operating conditions for each application may involve remarkably different characteristics regarding kinetics, heat transfer and material multicycle activity performance. The novelty and urgency of developing these applications demand an important effort to overcome serious issues, most of them related to gas-solids reactions and material handling. This work reviews the latest results from international research projects including a critical assessment of the technology needed to scale up the process. A set of equipment and methods already proved as well as those requiring further demonstration are discussed. An emphasis is put on critical equipment such as gas-solids reactors for both calcination and carbonation, power block integration, gas and solids conveying systems and auxiliary equipment for both energy storage and CO capture CaL applications.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Overlooked pitfalls in CaO carbonation kinetics studies nearby equilibrium: Instrumental effects on calculated kinetic rate constants

  • Arcenegui-Troya, Juan
  • Durán-Martín, Jonatan D.
  • Perejón, Antonio
  • Valverde, José M.
  • Pérez-Maqueda, Luis A.
  • Sánchez-Jiménez, Pedro E.
Abstract Due to its technological applications, such as CO2 capture, CaO carbonation kinetics has been extensively studied using a wide array of methods and experimental conditions. A complete understanding of carbonation kinetics is key to optimizing the operating conditions as well as to correctly design the carbonation reactor. However, there is yet no consensus on the reaction model and kinetic parameters that can best describe the CaO carbonation reaction. For instance, the value of the activation energy proposed in different works can vary up to 300%. In this work, we demonstrate that the strong influence of the thermodynamic equilibrium on CaO carbonation kinetics demands careful control of the experimental conditions to obtain meaningful kinetic parameters. Specifically, we explore the influence of three experimental parameters on carbonation kinetics: the gas flow rate, the CO2 partial pressure and the time required to fill the reactor after a gas change. We demonstrate that disregarding these aspects may lead to bogus conclusions on reaction kinetics, which could partly explain the considerable discrepancies found in the literature. The conclusions of this work are not only applicable to the process and experimental setup studied here but also to any study that involves the use of gas flow to drive a reaction, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

The SrCO3/SrO system for thermochemical energy storage at ultra-high temperature

  • Amghar, Nabil
  • Ortiz, Carlos
  • Perejón, Antonio
  • Valverde, J. M.
  • Pérez-Maqueda, Luis A.
  • Sánchez-Jiménez, Pedro E.
Thermochemical energy storage (TCES) has attracted interest in the last years due to the possibility of attaining high energy densities, seasonal storage capacity and greater efficiencies than currently commercial thermal energy storage systems using molten salts. This work analyses the potential of an ultra-high temperature TCES system based on the SrCO3/SrO system. The process relies upon the reversible decomposition of SrCO3 into SrO and CO2. As proposed in previous works for the integration of the Ca-Looping process to store energy in CSP plants, both the calcination (endothermic) and carbonation (exothermic) reactions are carried out in a closed CO2 loop. At these conditions, the required temperature to attain full calcination in short residence times is around 1400 ◦C whereas carbonation takes place at about 1200 ◦C. Using this process, the energy density potentially achievable by the storage material is very high (around 2000 MJ/m3 ) while the ultra-high carbonation temperature would improve thermoelectric efficiency. The enhancement of the multicycle performance of the SrCO3/SrO system using refractory additives is also explored. Even though current commercial CSP plants with tower technology cannot yet operate at these ultra-high temperatures, recent advances in the development of high-temperature solar receivers could allow operation at 1400 ◦C in the medium term. Finally, a conceptual model of the integration of the SrCO3/SrO system in a CSP plant supports higher overall efficiency and energy density, but lower solar-to-electric efficiency due to thermal losses., This work has been supported by the Spanish Government Agency Ministerio de Economía, Industria y Competitividad, the Agencia Estatal de Investigación and FEDER (contracts CTQ2017-83602- C2-1-R and -2- R) and Junta de Andalucía-Consejería de Conocimiento, Investigación y Universidad-Fondo Europeo de Desarrollo Regional (FEDER) (Programa Operativo FEDER Andalucía 2014–2020, projects P18-FR-1087 and US1262507). We also acknowledge the funding received by the European Union’s Horizon 2020 research and innovation programme under grant agreement No. 727348, project SOCRATCES., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Steam-enhanced calcium-looping performance of limestone for thermochemical energy storage: The role of particle size

  • Arcenegui-Troya, J.
  • Sánchez-Jiménez, Pedro E.
  • Perejón, Antonio
  • Valverde, José M.
  • Pérez-Maqueda, Luis A.
Steam injection has been proposed to attenuate the decay of CaO reactivity during calcium looping (CaL) under operating conditions compatible with carbon capture and storage. However, it is yet unknown whether the perceived advantages granted by steam hold under the distinct operating conditions required for the integration of the CaL process as a thermochemical energy storage system in Concentrating Solar Power Plants (CaL-CSP). Here, we study the influence of steam in conditions compatible with a CaL-CSP scheme and assess its impact when injected only during one stage; either calcination or carbonation, and also when it is present throughout the entire loop. The results presented here demonstrate that steam boosts the CaO multicycle performance in a CO2 closed loop to attain residual conversion values similar to those achieved at moderate temperatures under inert gas. Moreover, it is found that the enhancement in multicycle activity is more pronounced for larger particles., This work has been supported by the Spanish Government Agency Ministerio de Economía y Competitividad-FEDER (contracts CTQ2017- 83602-C2-1-R and -2-R) and Junta de Andalucía and Universidad de Sevilla (Programa Operativo FEDER Andalucía 2014–2020, projects P18-FR-1087 and US-1262507). We acknowledge the funding received by the European Union's Horizon 2020 research and innovation programme under grant agreement No. 727348, project SOCRATCES. Financial support received from Junta de Andalucía-Consejería de Economía, Conocimiento, Empresas y Universidad via a postdoctoral fellowship with reference DOC_00044 is also acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Carbonation tests in a kW-scale entrained flow reactor for thermochemical energy storage using the calcium looping-based system

  • Chacartegui, Ricardo
  • Gravanis, Georgios
  • Carro, Andrés
  • Ortiz, Carlos
  • Pérez-Maqueda, Luis A.
  • Amghar, Nabil
  • Tejada, Carlos
  • Karagiannakis, George P.
  • Tsimpanogiannis, Ioannis N.
  • Papadopoulou, Simira A.
  • Voutetakis, S.
Deploying reliable and sustainable large-scale energy storage is a significant challenge for the widespread adoption of renewable energy sources. Thermal energy storage solutions can provide scalable solutions for renewable power and industrial processes. The calcium looping-based energy storage system stands out for its high energy density, low cost, non-toxicity, and wide availability of limestone as a precursor material. The thermochemical energy storage cyclic process occurs through the calcination of calcium carbonate and its subsequent recovery through carbonation of calcium oxide. This work presents the development and tests of a novel entrained flow carbonator developed during the SOCRATCES EU project. The results show for the first time a successful CaO carbonation reaction in kW-scale equipment under energy storage conditions. The carbonation reaction occurs in an entrained flow reactor in few seconds at the temperature and pressure conditions required for the Calcium-looping-based energy storage system (700–800 °C). It demonstrates the feasibility of the entrained flow reactor concept for carbonation and its potential for MW-scale solar plants., This research was funded by the European Union's Horizon 2020 Research and Innovation Programme, grant number 727348, “SOlar Calcium-looping integRAtion for Thermo-Chemical Energy Storage” (SOCRATCES) project., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Modelling calcium looping at industrial scale for energy storage in concentrating solar power plants

  • Bailera, Manuel
  • Pascual, Sara
  • Lisbona, Pilar
  • Romeo, Luis
Ca-Looping represents one of the most promising technologies for thermochemical energy storage. This process based on the carbonation-calcination cycle of CaO offers a high potential to be coupled with solar power plants for its long-term storage capacity and high temperatures. Previous studies analyzed different configurations of CaL integrated into power cycles aiming to improve efficiency. However, most of these assessments based on lumped models did not account for scale effect in the most critical reactor. In this work, a detailed 1D-model of a large-scale carbonator is included in the comprehensive model of the integrated facility. The results obtained served to assess the available heat, the minimum technical part load of this equipment, the required size of the storage tanks and the overall efficiency of the plant. The main issue in the operation of large-size carbonator is the heat removal, thus a multi-tube internally cooled reactor is proposed. The designed carbonator provides 80 MWth at nominal operation and 40 MWth at minimum part load operation. The sizing of storage tanks depends on the operation management, ranging between 5,700-11,400 m3 for 15 hours. Different efficiencies of the system were defined and presented through operating maps, as a function of the reactor loads.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Calcium looping as chemical energy storage in concentrated solar power plants: Carbonator modelling and configuration assessment

  • Bailera, Manuel
  • Lisbona, Pilar
  • Romeo, Luis M.
  • Díez, Luis I.
This paper addresses the analysis of different configurations of carbonator for thermochemical energy storage for concentrated solar applications. The design of this equipment is different from the previous experience of calcium looping cycle for carbon capture. The use of fluidized beds and large particles are not feasible for this novel application of calcium looping. New reactors and different arrangements for the carbonation process are necessary. The design of a carbonator reactor for a specific Calcium Looping-Concentrated Solar Power application has not been addressed yet in detail in literature. In this work, a comparison of single stage reactor, two parallel reactors and two reactors in series with intercooling are simulated to calculate conversion rates, gas temperatures and flow rates, and heat transfer rates to the external cooling fluid. The modelling encompasses fluid dynamics, lime conversion kinetics and heat transfer, which are solved using a 1-D discrete mesh. The third arrangement results in the most reasonable sizes, and larger conversion rates, avoiding the occurrence of internal reactor zones in which the reaction is inhibited. Energy balance components are also quantified for each configuration.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Design and operational performance maps of calcium looping thermochemical energy storage for concentrating solar power plants

  • Pascual, Sara
  • Lisbona, Pilar
  • Bailera, Manuel
  • Romeo, Luis
Calcium-looping thermochemical energy storage associated to concentrating solar plants appears as promising technology given its potential to increase the storage period and energy density of the stored material. Up to now, research efforts focused on the global efficiency of the TCES associated to different power cycles under fixed modes of operation: day or night. However, TCES will never operate under a stationary situation but will experience different operation points to adapt to solar availability and energy demand from the power cycle. The aim is to analyse the influence of those variables which define the operation points, under energy storage and release modes, in the design of the heat exchangers network, storage tanks and reactors involved in the TCES system. The equipment in the conceptual plant have been modelled accounting variable storage/discharge fractions in the mass balances. The results show a suitable capture efficiency, quantifies the stored power and define the size and performance of the heat exchangers required to operate the system. The behaviour of each heat exchanger and their relevance in heat integration with a power plant is derived. The novelty relies in the analysis of potential situations arising from different combinations of charge/discharge fractions of storage tanks.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Operation maps in calcium looping thermochemical energy storage for concentrating solar power plants

  • Pascual, S.
  • Lisbona, P.
  • Romeo, L.M.
Calcium Looping (CaL) process used as thermochemical energy storage system in concentrating solar plants has been extensively investigated in the last decade and the first large-scale pilot plants are now under construction. Existing research focuses on improving global efficiencies under steady-state and single modes of operation: energy storage or energy retrieval. However, TCES systems will operate under different operation points to adapt the load of its reactors to the solar availability and the energy demand from the power cycle. A thorough analysis of the operation modes provides an extremely large number of potential situations to operate the system. In this study, operation maps which maximize thermal energy availability and energy storage efficiency are defined. Furthermore, a novel approach for the management of partially carbonated solids is examined to reduce the circulation of inert material in the system based on preliminary experimental results which allows for a partial separation of carbonated solids. Two threshold scenarios are analysed: (i) no solids separation as considered in most CaL TCES studies and (ii) ideal total solids separation. The aims of this work are to set methodological criteria to define the optimal operation map and to assess the effect of partially carbonated solids separation on the energy penalties and equipment size. The inclusion of a solid separation stage leads to a maximum increase of energy storage efficiency of 26 % and a size reduction between 53 and 74 % of those heat exchangers affected by solids streams.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Reseña (Review)

Thermal Energy Storage in Concentrating Solar Power Plants: A Review of European and North American R&D Projects

  • Pascual, Sara
  • Lisbona, Pilar
  • Romeo, Luis M.
Thermal energy storage (TES) is the most suitable solution found to improve the concentrating solar power (CSP) plant’s dispatchability. Molten salts used as sensible heat storage (SHS) are the most widespread TES medium. However, novel and promising TES materials can be implemented into CSP plants within different configurations, minimizing the TES costs and increasing the working temperature to improve the thermal performance of the associated power block. The first objective of this review is to provide an overview of the most widespread CSP technologies, TES technologies and TES-CSP configurations within the currently operational facilities. Once this information has been compiled, the second aim is to collect and present the existing European and North American TES-CSP Research and Development (R&D) projects within the last decade (2011–2021). Data related to these projects such as TES-CSP configuration path, TES and CSP technologies applied, storage capacity, power block associated and the levelized cost of electricity (LCOE) of the commercial up-scaling project are presented. In addition, project information such as location, research period, project leader and budget granted are also extracted. A timeline of the R&D projects launched from 2011 is built, showing the technology readiness level (TRL) achieved by the end of the project.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Optimized Ca-looping thermochemical energy storage under dynamic operation for concentrated solar power

  • Pascual, S.
  • Romeo, L.M.
  • Lisbona, P.
The massive deployment of renewable energy sources and carbon capture technologies are required to achieve net zero emissions target by 2050. Calcium Looping (CaL) is a promising Thermochemical Energy Storage (TCES) system which improves the dispatchability of Concentrating Solar Power (CSP) plants. CaL TCES configurations found in literature focus on a steady-state analysis of thermal-to-electric efficiency of the CSP plants. In this work, the operation of the CaL TCES system for a CSP plant is economically optimized taking into account the seasonal and daily variations of solar resource and electricity prices. The defined methodology determines the operating performance of the CaL TCES which maximize the economic incomes of the CSP and the daily profiles of energy production and storage for representative days of the different seasons/periods of the year. Results show that it is possible to obtain good economic results and operate the CSP + storage for a daily maximization of incomes. Obtained results are also useful for the final design of the system and for the definition of the size required for the storage equipment.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Energy consumption minimization for a solar lime calciner operating in a concentrated solar power plant for thermal energy storage

  • Lisbona, P.
  • Bailera, M.
  • Hills, T.
  • Sceats, M.
  • Díez, L.I.
  • Romeo, L.M.
Calcium-looping systems can be integrated in concentrated solar power (CSP) plants as an alternative for thermal energy storage. This storage concept is based in the high temperature reversible calcination-carbonation reactions, in which limestone and lime are alternatively converted. Energy from CSP can be stored by limestone calcination (endothermic reaction) at high temperatures producing pure streams of CaO and CO2. This energy can be later released when demand increases by means of carbonation reaction (exothermic) at relatively high temperatures. Calciner reactor is a complex system where heterogeneous chemical reactions take place while absorbing heat from solar concentrating equipment. It is a key element of the process. Depending on the design and the distribution of heat along the calciner, the amount of energy required to store the same amount of chemical energy in the form of lime varies, as well as the temperature of the solids. Optimal design and operating conditions will minimize average temperature in the calciner for a given flow of produced lime. In this work, the modelling of a multi-stage solar calciner is described in the frame of a new solar-based CSP plant.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Partial separation of carbonated material to improve the efficiency of calcium looping for the thermochemical storage of solar energy

  • Pascual, Sara
  • Tregambi, Claudio
  • Di Lauro, Francesca
  • Solimene, Roberto
  • Salatino, Piero
  • Montagnaro, Fabio
  • Romeo, Luis M.
  • Lisbona, Pilar
Concentrating solar power (CSP) technology with thermal energy storage (TES) could contribute to achieving a net zero emissions scenario by 2050. Calcium looping (CaL) is one of the potential TES processes for the future generation of CSP plants coupled with highly efficient power cycles. Research on CaL as a system for thermochemical energy storage (TCES) has focused on efficiency enhancement based on hybridization with other renewable technologies. This work proposes a novel solid management system to improve the efficiency of a CaL TCES system. The inclusion of a solid–solid separation unit after the carbonation step could lead to energy and size savings. The role of segregation between carbonated and calcined material on plant requirements is assessed, given the experimental evidence on the potential classification between more and less carbonated particles. The results show lower energy (up to 12%) and size (up to 76%) demands when the circulation of less carbonated material through the CaL TCES system diminishes. Moreover, under a classification effectiveness of 100%, the retrieval energy could increase by 32%, and the stored energy is enhanced by five times. The present work can be a proper tool to set the design and size of a CaL TCES system with a partial separation of the carbonated material.