Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 24
Encontrada(s) 1 página(s)

RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Enhanced CO2 capture by cupuassu shell-derived activated carbon with high microporous volume

  • Cruz Jr., Orlando F.
  • Campello-Gómez, Ignacio
  • Casco, Mirian Elizabeth
  • Serafin, Jarosław
  • Silvestre-Albero, Joaquín
  • Martinez-Escandell, Manuel
  • Hotza, Dachamir
  • Rambo, Carlos R.
  • Martinez-Escandell, Manuel|||/items/d1b86ef0-e06d-4f75-b78d-9e650b53ca0e
  • Silvestre-Albero, Joaquín|||/items/340b8128-2e1e-4869-8845-03b1802a1577
Here, we report the preparation of microporous-activated carbons from a Brazilian natural lignocellulosic agricultural waste, cupuassu shell, by pyrolysis at 500 ºC and KOH activation under different experimental conditions and their subsequent application as adsorbent for CO2 capture. The effect of the KOH:precursor ratio (wt/wt%) and the activation temperature on the porous texture of activated carbons have been studied. The values of specific surface area ranged from 1132 to 2486 m2/g, and the overall micropore volume ranged from 0.73 to 1.02 cm3/g. Carbons activated with 2:1 ratio of KOH and activation temperature of 700 ºC presented a CO2 adsorption at 1 bar of 7.8 and 4.4 mmol/g at 0 °C and 25 ºC, respectively. The isosteric heat of adsorption, Qst, was calculated for all samples by applying the Clausius–Clapeyron approach to CO2 adsorption isotherms at both temperatures. The values of CO2 adsorption capacities are among the highest reported in the literature, especially for activated carbons produced from biomass.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Activated carbons with high micropore volume obtained from polyurethane foams for enhanced CO2 adsorption

  • Cruz Jr., Orlando F.
  • Campello-Gómez, Ignacio
  • Rodríguez Reinoso, Francisco
  • Silvestre-Albero, Joaquín
  • Rambo, Carlos R.
  • Martinez-Escandell, Manuel
  • Martinez-Escandell, Manuel|||/items/d1b86ef0-e06d-4f75-b78d-9e650b53ca0e
  • Silvestre-Albero, Joaquín|||/items/340b8128-2e1e-4869-8845-03b1802a1577
Microporous activated carbons with remarkably high CO2 uptake have been synthesized using polyurethane (PU) commercial foams as precursors. The PU samples were pyrolyzed at different temperatures in N2 atmosphere and chemically activated with KOH. Adsorption isotherms at 0 °C and 25 °C and immersion calorimetry were applied to provide a deeper knowledge about the most relevant factors implied in CO2 capture process explaining, hence, the values of adsorption obtained. CO2 adsorption uptakes reached values of 7.4 mmol/g at 0 °C, 5.0 mmol/g at 25 °C and 2.7 mmol/g at 50 °C. The remarkably high values of CO2 uptake are closely related with the BET specific surface area of the carbon foams but also with the high volume of narrow micropores all the samples present a high volume of micropores (between 0.59 and 0.71 cm3/g) as also confirmed by immersion calorimetry.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Tuning porosity in macroscopic monolithic metal-organic frameworks for exceptional natural gas storage

  • Connolly, Bethany M.
  • Aragones-Anglada, Marta
  • Gandara-Loe, Jesús
  • Danaf, Nader Al
  • Lamb, Don C.
  • Mehta, Josh P.
  • Vulpe, Diana
  • Wuttke, Stefan
  • Silvestre-Albero, Joaquín
  • Moghadam, Peyman Z.
  • Wheatley, Andrew E.H.
  • Fairen-Jimenez, David
  • Silvestre-Albero, Joaquín|||/items/340b8128-2e1e-4869-8845-03b1802a1577
Widespread access to greener energy is required in order to mitigate the effects of climate change. A significant barrier to cleaner natural gas usage lies in the safety/efficiency limitations of storage technology. Despite highly porous metal-organic frameworks (MOFs) demonstrating record-breaking gas-storage capacities, their conventionally powdered morphology renders them non-viable. Traditional powder shaping utilising high pressure or chemical binders collapses porosity or creates low-density structures with reduced volumetric adsorption capacity. Here, we report the engineering of one of the most stable MOFs, Zr-UiO-66, without applying pressure or binders. The process yields centimetre-sized monoliths, displaying high microporosity and bulk density. We report the inclusion of variable, narrow mesopore volumes to the monoliths’ macrostructure and use this to optimise the pore-size distribution for gas uptake. The optimised mixed meso/microporous monoliths demonstrate Type II adsorption isotherms to achieve benchmark volumetric working capacities for methane and carbon dioxide. This represents a critical advance in the design of air-stable, conformed MOFs for commercial gas storage.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Assessment of Phenolic and Indolic Compound Removal from Aqueous Media Using Lignocellulose-Derived Surface-Modified Nanoporous Carbon Adsorbents: A Comparative Study

  • Jandosov, J.M.
  • Chenchik, D.I.
  • Baimenov, Alzhan
  • Silvestre-Albero, Joaquín
  • Bernardo, Maria
  • Azat, Seitkhan
  • Doszhanov, Yerlan
  • Sabitov, Aitugan
  • Busquets, Rosa
  • Howell, C.A.
  • Mikhalovsky, S.V.
  • Mansurov, Zulkhair
  • Silvestre-Albero, Joaquín|||/items/340b8128-2e1e-4869-8845-03b1802a1577
P-cresol, indole and indole-3-acetic acid (IAA) are catabolites of amino acids, formed by the gut microbiome. Most of these aromatic hydrocarbon derivatives are excreted by the colon before reentering the body to form “exogenous” protein-bound uremic toxins (PBUTs), which aggravate chronic kidney disease (CKD). Removal efficiencies of these PBUT precursors from model phosphate-buffered saline solutions by three different surface-modified nanoporous carbon adsorbents (PCs) were studied. PCs were produced by physicochemical and/or acid base activation of carbonized rice husk waste. Removal rates achieved values of 32–96% within a 3 h contact time. High micro/mesoporosity and surface chemistry of the N- and P-doped biochars were established by N2 adsorption studies, SEM/EDS analysis, XPS and FT-IR-spectroscopy. The ammoxidized PC-N1 had the highest adsorption capacity (1.97 mmol/g for IAA, 2.43 mmol/g for p-cresol and 2.42 mmol/g for indole), followed by “urea-nitrified” PC-N2, whilst the phosphorylated PC-P demonstrated the lowest adsorption capacity for these solutes. These results do not correlate with the total pore volume values for PC-N2 (0.91 cm3/g) < PC-P (1.56 cm3/g) < PC-N1 (1.84 cm3/g), suggesting that other parameters such as the micropore volume (PC-N1 > PC-N2 > PC-P) and the interaction of surface chemical functional groups with the solutes play key roles in the adsorption mechanism. N-doped PC-N1 and PC-N2 have basic functional groups with higher affinity with acidic IAA and p-cresol. The ion-exchange mechanism of phenolic and indolic compound chemisorption by nanoporous carbon adsorbents, modified with surface N- and P-containing functional groups, has been proposed.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Sulfonated activated carbons as potential catalysts for biolubricant synthesis

  • Ferreira, Aurélia R.O.
  • Silvestre-Albero, Joaquín
  • Maier, Martin E.
  • Ricardo, Nágila M.P.S.
  • Cavalcante Jr, Célio L.
  • Luna, F. Murilo T.
  • Silvestre-Albero, Joaquín|||/items/340b8128-2e1e-4869-8845-03b1802a1577
In this study, sulfonated activated carbons have been prepared, under different conditions, with the purpose of evaluating the effect of the nature and amount of sulfonic surface groups on the esterification reaction of free fatty acids (FFA) with different long-chain alcohols. The synthesized catalysts were characterized using different techniques and 1H NMR was used for monitoring the reaction products. The modifications of the surface functionalities were assessed by X-ray Photoelectron Spectroscopy (XPS) and Thermogravimetric analysis (TGA), while changes in the porous network and morphology of the samples were evaluated before and after the treatment of the original activated carbon sample. XPS results showed the presence of two types of sulfur, one from thiophenic sulfur (present on all materials, including the unmodified sample), and the other from sulfonic groups (SO3H), at 168 eV (present only in the modified samples). These catalysts were applied in the esterification reaction and presented excellent catalytic performances, while the original activated carbon exhibited conversions similar to reactions without any catalyst. On the other hand, the conversion of fatty acids when using the modified carbons improves significantly with values up to ∼100 % to mono alcohols and 70 % to trimethylolpropane.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Sulfonated MCM-41 as potential catalyst to obtain biolubricants from vegetable oil

  • Ferreira, Aurélia R.O.
  • Silvestre-Albero, Joaquín
  • Maier, Martin E.
  • Ricardo, Nágila M.P.S.
  • Cavalcante Jr, Célio L.
  • Luna, F. Murilo T.
  • Silvestre-Albero, Joaquín|||/items/340b8128-2e1e-4869-8845-03b1802a1577
Biolubricants may be obtained from vegetable oils using appropriate chemical modifications, to improve their physicochemical properties for lubrication applications. In this study, the esterification of a free fatty acid (FFA) with long chain alcohols was performed using sulfonated mesoporous silica as catalyst. Fresh and functionalized MCM-41 samples were prepared to evaluate the effect of the sulfonic surface group on the esterification reaction. MCM-41 was functionalized via post-synthesis modification using 3-mercaptopropyltrimethoxysilane (MPTS) as silylating agent. The synthesized catalysts were characterized using several techniques. After the functionalization, a decrease in the apparent surface area and pore diameter were observed. The MCM-41/SO3H sample was applied in the esterification reaction of oleic acid (as a FFA model) using two different long-chain alcohols (octanol and 2-ethylhexanol). The catalytic results reveal that sulfonated catalyst showed excellent conversions (~ 100% mol when using octanol and > 93% mol using 2-ethylhexanol) and selectivities to esters (ca. 90%).
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

New insights into the breathing phenomenon in ZIF-4

  • Gandara-Loe, Jesús
  • Missyul, Alexander
  • Fauth, François
  • Daemen, Luke L.
  • Cheng, Yongqiang
  • Ramírez-Cuesta, Anibal J.
  • Ravikovitch, Peter I.
  • Silvestre-Albero, Joaquín
  • Silvestre-Albero, Joaquín|||/items/340b8128-2e1e-4869-8845-03b1802a1577
Structural changes in ZIFs upon adsorption remain a paradigm due to the sensitivity of the adsorption mechanism to the nature of the organic ligands and gas probe molecules. Synchrotron X-ray diffraction under operando conditions clearly demonstrates for the first time that ZIF-4 exhibits a structural reorientation from a narrow-pore (np) to a new expanded-pore (ep) structure upon N2 adsorption, while it does not do so for CO2 adsorption. The existence of an expanded-pore structure of ZIF-4 has also been predicted by molecular simulations. In simulations the expanded structure was stabilized by entropy at high temperatures and by strong adsorption of N2 at low temperatures. These results are in perfect agreement with manometric adsorption measurements for N2 at 77 K that show the threshold pressure for breathing at ∼30 kPa. Inelastic neutron scattering (INS) measurements show that CO2 is also able to promote structural changes but, in this specific case, only at cryogenic temperatures (5 K).
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Enhancing graphitization and mesoporosity by cobalt in activated carbons obtained from peach stone

  • Campello-Gómez, Ignacio
  • Cruz Jr., Orlando F.
  • Rambo, Carlos R.
  • Ramos-Fernández, Enrique V.
  • Sepúlveda-Escribano, Antonio
  • Ramos-Fernández, Enrique V.|||/items/bfb4ad7a-ea42-4779-b123-a12caf1ae2d1
  • Sepúlveda-Escribano, Antonio|||/items/5559b16f-e8a5-408d-8b38-429fa29048b0
Activated carbon (AC) is a common material of choice in catalysis, as it is a suitable support material for many catalytic reactions. In this work, the effect of cobalt nanoparticles on activated carbon derived from a biomass waste, peach stone, is reported. The presence of cobalt during heat treatments at 900 °C under reductive (H2) and inert (He) atmospheres resulted in the appearance of an intense 2D band in the Raman spectra, indicating a high degree of graphitization. Temperature-programmed reduction and desorption experiments were conducted to evaluate the activation reactions. Quenched solid density functional theory (QSDFT) analysis using N2 adsorption data revealed that cobalt increased pore development in the samples, regardless of the atmosphere (reductive or inert) used.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Structural Flexibility in Activated Carbon Materials Prepared under Harsh Activation Conditions

  • Gomes Ferreira de Paula, Fabiano
  • Campello-Gómez, Ignacio
  • Ortega, Paulo Fernando Ribeiro
  • Rodríguez Reinoso, Francisco
  • Martinez-Escandell, Manuel
  • Silvestre-Albero, Joaquín
  • Martinez-Escandell, Manuel|||/items/d1b86ef0-e06d-4f75-b78d-9e650b53ca0e
  • Silvestre-Albero, Joaquín|||/items/340b8128-2e1e-4869-8845-03b1802a1577
Although traditionally high-surface area carbon materials have been considered as rigid structures with a disordered three dimensional (3D) network of graphite microdomains associated with a limited electrical conductivity (highly depending on the porous structure and surface chemistry), here we show for the first time that this is not the case for activated carbon materials prepared using harsh activation conditions (e.g., KOH activation). In these specific samples a clear structural re-orientation can be observed upon adsorption of different organic molecules, the structural changes giving rise to important changes in the electrical resistivity of the material. Whereas short chain hydrocarbons and their derivatives give rise to an increased resistivity, the contrary occurs for longer-chain hydrocarbons and/or alcohols. The high sensitivity of these high-surface area carbon materials towards these organic molecules opens the gate towards their application for sensing devices.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Role of KCl in activation mechanisms of KOH-chemically activated high surface area carbons

  • Campello-Gómez, Ignacio
  • Cruz Jr., Orlando F.
  • Silvestre-Albero, Joaquín
  • Rambo, Carlos R.
  • Martinez-Escandell, Manuel
  • Martinez-Escandell, Manuel|||/items/d1b86ef0-e06d-4f75-b78d-9e650b53ca0e
  • Silvestre-Albero, Joaquín|||/items/340b8128-2e1e-4869-8845-03b1802a1577
Activated carbons from different precursors have been synthetized using KOH and mixtures of KOH and KCl as activating agents. The results revealed an increase of surface area and yield of activation related with KCl addition in all the samples. Thermodynamic and mass spectrometry studies reveal that KCl do not act as an activating agent, but promotes the solubilisation of secondary products of the reactions such as carbonates, enhancing the contact of KOH and carbon particles, therefore increasing the efficiency of the activation. Based on mass spectroscopy results, combined with thermodynamic calculations, we proposed four reactions as the most likely responsible for the pore development during activation.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Controlling the Adsorption and Release of Ocular Drugs in Metal–Organic Frameworks: Effect of Polar Functional Groups

  • Farrando Pérez, Judit
  • Martínez Navarrete, Gema Concepción
  • Gandara-Loe, Jesús
  • Reljic, Snezana
  • García Ripoll, Antonio
  • Fernandez, Eduardo
  • Silvestre-Albero, Joaquín
  • Silvestre-Albero, Joaquín|||/items/340b8128-2e1e-4869-8845-03b1802a1577
  • Farrando Pérez, Judit|||/items/34cb81d0-92fd-40d7-84b9-1b0ab766f49c
A series of UiO-66 materials with different functional groups (−H, −NH2, and −NO2) have been evaluated for the adsorption and release of a common ocular drug such as brimonidine tartrate. UiO-66 samples were synthesized under solvothermal conditions and activated by solvent exchange with ethanol. Experimental results suggest that the incorporation of surface functionalities gives rise to the development of structural defects (missing linker defects) but without altering the basic topology of the UiO-66 framework. These defects improve the adsorption performance of the parent metal–organic framework (MOF), while the bulkier functionalities infer slower release kinetics, with the associated benefits for prolonged delivery of brimonidine. Among the evaluated MOFs, defective UiO-66-NO2 can be proposed as the most promising candidate due to the combination of a larger brimonidine volumetric uptake (680 mg/cm3), a prolonged delivery (period of up to 25 days), a small particle size, and a larger instability. Contrariwise, at high concentrations UiO-66-NO2 has higher toxicity toward human retinal pigment epithelium cells (ARPE-19) compared to the pure and NH2-functionalized UiO-66.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Direct Measurement of Microporosity and Molecular Accessibility in Stöber Spheres by Adsorption Isotherms

  • Farrando Pérez, Judit
  • López, Cefe
  • Silvestre-Albero, Joaquín
  • Gallego-Gómez, Francisco
  • Silvestre-Albero, Joaquín|||/items/340b8128-2e1e-4869-8845-03b1802a1577
  • Farrando Pérez, Judit|||/items/34cb81d0-92fd-40d7-84b9-1b0ab766f49c
The microporous nature of monodisperse Stöber silica spheres is demonstrated in the literature, although usually via indirect evidence. Contradictorily, there also exist numerous reports of nonporosity based on conventional N2 adsorption isotherms, leading to a confusing scenario and questioning the evaluation methodology. Thus, there is the strong need of straight measure of microporosity in Stöber spheres, at best by available adsorption techniques, which must be further directly confronted with the standard nitrogen method. Here, for the first time, microporosity detection by N2 and CO2 adsorption is compared in Stöber spheres. We demonstrate that CO2 isotherms at 273 K allow direct detection and quantification of the microporosity (about 0.1 cm3/g in our samples), while N2 at 77 K cannot probe adequately the internal volume. We also show that a large amount of water fills the micropores under usual ambient conditions, also revealing the presence of small mesoporosity. Thus, the porous nature of Stöber spheres is investigated by a simple combination of adsorption isotherms, and the different accessibility of N2, CO2, and H2O molecules is discussed. We emphasize the inadequacy of standard N2 isotherms for micropore detection in Stöber silica, as the access of nitrogen molecules at cryogenic temperatures is kinetically restricted and may lead to erroneous conclusions. Instead, we propose CO2 isotherms as a simple and direct means for evaluation of microporosity.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Freezing/melting of water in the confined nanospace of carbon materials: Effect of an external stimulus

  • Cuadrado-Collados, Carlos
  • Majid, Ahmad A.A.
  • Martinez-Escandell, Manuel
  • Daemen, Luke L.
  • Missyul, Alexander
  • Koh, Carolyn
  • Silvestre-Albero, Joaquín
  • Martinez-Escandell, Manuel|||/items/d1b86ef0-e06d-4f75-b78d-9e650b53ca0e
  • Silvestre-Albero, Joaquín|||/items/340b8128-2e1e-4869-8845-03b1802a1577
Freezing/melting behavior of water confined in the nanopores of activated carbon materials has been evaluated using differential scanning calorimetry (DSC) at different water loadings, and after the application of an external stimulus. Under atmospheric pressure conditions, the DSC scans show a depression in the freezing/melting point of confined water compared to the bulk system. Interestingly, water confined in narrow micropores (pores below 0.7 nm) does not exhibit any phase transition, i.e. it is non-freezable water. Inelastic neutron scattering (INS) data confirm the presence of a distorted molecular assembly in narrow micropores, whereas synchrotron X-ray powder diffraction data (SXRPD) demonstrate the non-freezable nature of the water confined in these narrow-constrictions. Similar experiments under high-pressure CH4 give rise to a completely different scenario. Under high-pressure conditions methane hydrates are formed with a water-to-hydrate yield of 100% for the under-saturated and saturated samples, i.e. in the presence of an external stimulus even water in narrow micropores is prone to experience a liquid-to-solid phase transition. These results confirm the beneficial role of carbon as a host structure to promote nucleation and growth of methane hydrates with faster kinetics and a higher yield compared to the bulk system and to other porous materials.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Effect of additives in the nucleation and growth of methane hydrates confined in a high-surface area activated carbon material

  • Cuadrado-Collados, Carlos
  • Farrando Pérez, Judit
  • Martinez-Escandell, Manuel
  • Missyul, Alexander
  • Silvestre-Albero, Joaquín
  • Martinez-Escandell, Manuel|||/items/d1b86ef0-e06d-4f75-b78d-9e650b53ca0e
  • Silvestre-Albero, Joaquín|||/items/340b8128-2e1e-4869-8845-03b1802a1577
  • Farrando Pérez, Judit|||/items/34cb81d0-92fd-40d7-84b9-1b0ab766f49c
A high-surface area activated carbon material (PPAC) prepared from a petroleum residue has been used as a host structure to promote the nucleation and growth of confined methane hydrates after the incorporation of additives. Sodium dodecyl sulfate (SDS), Leucine and Tetrahydrofuran (THF) have been evaluated either dissolved in the pre-impregnation media (ultrapure water) or incorporated in the carbon surface using a mechanochemical approach. High-pressure methane adsorption isotherms show that the mechanochemical approach does not improve the storage performance of the original carbon material due to the steric effects by the bulkier organic functionalities. Furthermore, the incorporation of the additives shifts the nucleation in narrow pores to higher pressures. On the contrary, when the additives are dissolved in water, high-pressure methane isotherms anticipate a modification in the kinetics and/or thermodynamics of the nucleation process. Whereas gas hydrates grown in large pores and/or the external surface exhibits a significant reduction in the induction time, the nucleation process in narrow micropores becomes more uniform and occurs in a narrower pressure window, slightly shifted to higher pressures. However, no changes in the total uptake at 10 MPa could be found. The situation is different when THF is dissolved in water. In this case, the nucleation takes place at pressures below the natural process (<3–4 MPa), the total amount of methane stored at 10 MPa being slightly limited. In-situ synchrotron X-ray diffraction studies anticipate a sI structure for the pure water methane hydrates, while a combination of sI and sII is identified for the THF-based system.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Metal–Organic Frameworks as Drug Delivery Platforms for Ocular Therapeutics

  • Gandara-Loe, Jesús
  • Ortuño-Lizarán, Isabel
  • Fernández-Sánchez, Laura
  • Alió, Jorge L.
  • Cuenca, Nicolás
  • Vega Estrada, Alfredo
  • Silvestre-Albero, Joaquín
  • Cuenca, Nicolás|||/items/9aff7e32-82c7-4c3b-9e61-c644ea7f9ec8
  • Fernández-Sánchez, Laura|||/items/1676ebd7-acc8-4ea8-bff6-d2b805dae60b
  • Ortuño-Lizarán, Isabel|||/items/81d05966-ec9c-49e0-8133-3867dc4836ad
  • Silvestre-Albero, Joaquín|||/items/340b8128-2e1e-4869-8845-03b1802a1577
Metal–organic frameworks (MOFs) have been evaluated as potential nanocarriers for intraocular incorporation of brimonidine tartrate to treat chronic glaucoma. Experimental results show that UiO-67 and MIL-100 (Fe) exhibit the highest loading capacity with values up to 50–60 wt %, whereas the performance is quite limited for MOFs with narrow cavities (below 0.8 nm, for example, UiO-66 and HKUST-1). The large loading capacity in UiO-67 is accompanied by an irreversible structural amorphization in aqueous and physiological media that promotes extended release kinetics above 12 days. Compared to the traditional drawbacks associated with the sudden release of the commercial drugs (e.g., ALPHAGAN), these results anticipate UiO-67 as a potential nanocarrier for drug delivery in intraocular therapeutics. These promising results are further supported by cytotoxicity tests using retinal photoreceptor cells (661W). Toxicity of these structures (including the metal nodes and organic ligands) for retinal cells is rather low for all samples evaluated, except for HKUST-1.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Synthesis, Morphostructure, Surface Chemistry and Preclinical Studies of Nanoporous Rice Husk-Derived Biochars for Gastrointestinal Detoxification

  • Jandosov, J.M.
  • Mikhalovska, L.I.
  • Howell, C.A.
  • Chenchik, D.I.
  • Kosher, B.K.
  • Lyubchik, S.B.
  • Silvestre-Albero, Joaquín
  • Ablaikhanova, N.T.
  • Srailova, G.T.
  • Tuleukhanov, S.T.
  • Mikhalovsky, S.V.
  • Silvestre-Albero, Joaquín|||/items/340b8128-2e1e-4869-8845-03b1802a1577
This article summarizes the methodology of synthesis, surface functionalization and structural properties of rice husk-derived nanostructured carbon enterosorbents (biochars) in connection with the preliminary in vitro study results of uraemic toxin adsorption in model experiments, as well as preclinical trials in vivo. The obtained nanostructured carbon sorbents were studied using a number of modern physicochemical methods of investigation: low-temperature nitrogen adsorption, isotherms recording and calculation of the specific surface area, pore volumes were carried out using the Autosorb-1 "Quantachrome" device. Scanning electron microscopy and EDS-analysis. Mercury intrusion porosimetry analysis of the ACs were accomplished using "Quantachrome Poremaster" data analysis software. In vitro adsorption results assessed by use of HPLC and UV-spectroscopy for the nanostructured carbon sorbents with respect to the investigated low-molecule toxins suggest that the rice husks-derived carbon enterosorbents modified with the functional groups are able to reduce clinically significant levels of uraemic toxins and are comparable to the commercial enterosorbents. Based on the results of the comparative analysis for biocompatibility of canine kidney epithelial cells it was determined that the samples of the modified sorbents CRH-P-450 and CRH-475-KOH-850-N do not exhibit cytotoxicity in comparison with the commercial carbon enterosorbent «Adsorbix Extra». According to the results of the in vivo studies, it was determined that there was a positive effect of the enterosorbent CRH-P-450 on uremia and intoxication.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

On the catalytic role of superficial VOx species and coke deposited on mesoporous MgO replica in oxidative dehydrogenation of ethylbenzene

  • Jarczewski, Sebastian
  • Drozdek, Marek
  • Michorczyk, Piotr
  • Cuadrado-Collados, Carlos
  • Gandara-Loe, Jesús
  • Silvestre-Albero, Joaquín
  • Lityńska-Dobrzyńska, Lidia
  • Kuśtrowski, Piotr
  • Silvestre-Albero, Joaquín|||/items/340b8128-2e1e-4869-8845-03b1802a1577
Mesoporous MgO was synthesized by the nanoreplication method using CMK-3 carbon as a hard template and magnesium nitrate as a metal oxide precursor. The produced support was modified with different amounts of ammonium metavanadate solution. Various distributions of V-containing species on the MgO surface were found by XRD, low-temperature adsorption of N2, TEM, XPS and UV–vis-DR spectroscopy. At low V loadings isolated VO4 dominated. Increasing V content resulted in clustering of VO4 species and the formation of Mg3V2O8 crystallites. As found in temperature-programmed reduction (H2-TPR), the latter phase was clearly harder in reduction by H2 compared to highly dispersed VO4 forms. The developed materials appeared to be very active catalysts of oxidative dehydrogenation of ethylbenzene (ODH). The optimal catalytic performance was observed for the sample containing 10 wt% of vanadium. The initial ethylbenzene conversion of 63.6% at selectivity to styrene of 86.9% was achieved at temperature as low as 500 °C. A notable influence of carbonaceous deposit formed during the ODH reaction on the catalytic activity was discussed, including presentation of both coexisting superficial reaction mechanisms. A reasonable regeneration procedure to recover lost activity was developed.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Evaluation of the textural properties of ultramicroporous carbons using experimental and theoretical methods

  • Grau-Marín, Daniel
  • Silvestre-Albero, Joaquín
  • Jardim, Erika de Oliveira
  • Jagiello, Jacek
  • Betz, William R.
  • Peña, Leidy E.
  • Silvestre-Albero, Joaquín|||/items/340b8128-2e1e-4869-8845-03b1802a1577
Spherical carbon molecular sieves (CMS) have selective adsorptive properties which are suitable for separation and purification of gas mixtures. Precise methods of characterization are needed to understand the performance of CMS in separation processes. To this end, the pore size distribution (PSD) of four carbon molecular sieves were evaluated experimentally using immersion calorimetry and complemented with gas adsorption measurements at cryogenic temperatures for N2, O2 and Ar, and at 273 K for CO2. Theoretical pore size distributions were estimated using two-dimensional non-local Density Functional Theory (2D-NLDFT) models. Calorimetry results showed that B and C samples had a narrow pore size distribution with pores below 0.7 nm. Meanwhile, the pore size distributions calculated from O2 and Ar adsorption isotherms, gave an apex in the 0.5–0.6 nm region for all the carbons together with a growing development of porosity at around 0.8 nm and above for carbons A and D. The agreement observed between experiments and theory confirmed the validity of the theoretical 2D-NLDFT models to anticipate the PSD. Carbon C with pores exclusively below 0.7 nm separated CO2 and CH4 while carbon D with pores in the supermicroporous region separated propane and propylene chromatographically.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Reverse Hierarchy of Alkane Adsorption in Metal–Organic Frameworks (MOFs) Revealed by Immersion Calorimetry

  • Cuadrado-Collados, Carlos
  • Rojas-Mayorga, Cintia Karina
  • Saavedra, Beatriz
  • Martinez-Escandell, Manuel
  • Osiński, Jacek M.
  • Moghadam, Peyman Z.
  • Fairen-Jimenez, David
  • Silvestre-Albero, Joaquín
  • Martinez-Escandell, Manuel|||/items/d1b86ef0-e06d-4f75-b78d-9e650b53ca0e
  • Silvestre-Albero, Joaquín|||/items/340b8128-2e1e-4869-8845-03b1802a1577
Immersion calorimetry into liquids of different dimensions is a powerful tool to learn about the pore size and shape in nanoporous solids. In general, in the absence of specific interactions with the solid surface, the accessibility of the liquid probe molecule to the inner porosity and the associated enthalpy value decreases with an increase in its kinetic diameter (bulkier molecules have lower accessibility and packing density). Although this is true for the majority of solids (e.g., activated carbons and zeolites), this study anticipates that this is not straightforward in the specific case of metal–organic frameworks (MOFs). The evaluation of different hydrocarbons and their derivatives reveals the presence of reverse selectivity for C6 isomers (2,2-dimethylbutane > 2-methylpentane > n-hexane) in UiO-66 and HKUST-1, whereas size exclusion effects take place in ZIF-8. The immersion calorimetric findings have been compared with vapor adsorption isotherms and computational studies. Monte Carlo simulations suggest that the reverse selectivity in UiO-66 is attributed to the strong confinement of the dibranched hydrocarbons in the small tetragonal cages, whereas the presence of strong interactions with the open metal sites accounts for the preferential adsorption in HKUST-1. These results open the gate toward the application of immersion calorimetry for the prescreening of MOFs to identify in an easy, fast and reliable way interesting characteristics and/or properties such as separation ability, reversed hierarchy, pore-window size, presence of unsaturated metal sites, molecular accessibility, and so on.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Molecular sieving of linear and branched C6 alkanes by tannin-derived carbons

  • Castro-Gutiérrez, Jimena
  • Jardim, Erika de Oliveira
  • Canevesi, Rafael L.S.
  • Silvestre-Albero, Joaquín
  • Kriesten, Martin
  • Thommes, Matthias
  • Celzard, Alain
  • Fierro, Vanessa
  • Silvestre-Albero, Joaquín|||/items/340b8128-2e1e-4869-8845-03b1802a1577
Two micro-mesoporous carbons (MMCs): a disordered mesoporous carbon (DMC) and an ordered mesoporous carbon (OMC), synthesized by an easy, low-cost, and green method are proposed as efficient hydrocarbon sieves for the separation of C6 isomers: n-hexane (nHEX), 2-methylpenthane (2 MP) and 2,2-dimethylbutane (22DMB). Their textural characterization reveals a highly interconnected pore network within the DMC, while a reverse hierarchy of ordered mesopores only accessible through narrow micropores is found in the OMC. The pore texture strongly affects their adsorption performance by kinetic and molecular sieving effects; the narrow constrictions in the OMC allow adsorption of nHEX and partially 2 MP but not 22DMB, whereas the highly connected pore network of DMC allows adsorption of the three isomers. Multi-component adsorption isotherms calculated from the single-component experimental results by ideal adsorbed solution theory (IAST) demonstrates that the OMC material has a remarkably high selectivity for the adsorption of nHEX and nHEX + 2 MP from binary and ternary mixtures, respectively. To the best of the authors’ knowledge, such behavior has never been reported so far for carbon materials. Hence, this study shows that tannin-derived MMCs have great potential to be used as an eco-friendly and low-cost alternative for the selective separation of di-branched C6 isomers.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Activated carbon from polyurethane residues as molecular sieves for kinetic adsorption/separation of CO2/CH4

  • Cruz Jr., Orlando F.
  • Campello-Gómez, Ignacio
  • Martinez-Escandell, Manuel
  • Rambo, Carlos R.
  • Silvestre-Albero, Joaquín
  • Martinez-Escandell, Manuel|||/items/d1b86ef0-e06d-4f75-b78d-9e650b53ca0e
  • Silvestre-Albero, Joaquín|||/items/340b8128-2e1e-4869-8845-03b1802a1577
Activated carbon-based molecular sieves were synthetized, characterized and their kinetics of adsorption were evaluated to be used in separation processes of CO2/CH4 mixtures. Polyurethane (PU) foams were used as carbon precursors and the PU-derived carbons were physical activated with CO2. All the samples present a preferential adsorption of CO2 over methane in kinetic adsorption experiments. Samples activated at 800 ºC during 6 h exhibited the highest selectivity due to the absence of methane adsorption at lower resident times, which makes those samples very interesting for industrial processes of natural gas purification. Kinetic studies were performed to explain the kinetic profiles obtained, confirming that in the samples with smallest pore size, intraparticle diffusion was the limiting step, evidencing that certain oxygen groups favour CO2 adsorption, whereas adsorption was the limiting step in the samples with wider pores.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Advanced Removal of Dyes with Tuning Carbon/TiO2 Composite Properties

  • Yankovych, Halyna Bodnar
  • Abreu-Jaureguí, Coset
  • Farrando Pérez, Judit
  • Melnyk, Inna
  • Václavíková, Miroslava
  • Silvestre-Albero, Joaquín
  • Abreu-Jaureguí, Coset|||/items/a98e5441-0b04-4cd6-b02e-2153b45f9c47
  • Silvestre-Albero, Joaquín|||/items/340b8128-2e1e-4869-8845-03b1802a1577
  • Farrando Pérez, Judit|||/items/34cb81d0-92fd-40d7-84b9-1b0ab766f49c
This study evaluates the removal of several dyes with different charge properties, i.e., anionic (Acid Red 88), cationic (Basic Red 13), and neutral (Basic Red 5) using transition metal-doped TiO2 supported on a high-surface-area activated carbon. Experimental results confirm the successful deposition of TiO2 and the derivatives (Zr-, Cu-, and Ce-doped samples) on the surface of the activated carbon material and the development of extended heterojunctions with improved electronic properties. Incorporating a small percentage of dopants significantly improves the adsorption properties of the composites towards the three dyes evaluated, preferentially for sample AC/TiO2_Zr. Similarly, the photodegradation efficiency highly depends on the nature of the composite evaluated and the characteristics of the dye. Sample AC/TiO2_Zr demonstrates the best overall removal efficiency for Acid Red 88 and Basic Red 5—83% and 63%, respectively. This promising performance must simultaneously be attributed to a dual mechanism, i.e., adsorption and photodegradation. Notably, the AC/TiO2_Ce outperformed the other catalysts in eliminating Basic Red 13 (74%/6 h). A possible Acid Red 88 degradation mechanism using AC/TiO2_Zr was proposed. This study shows that the removal efficiency of AC/TiO2 composites strongly depends on both the material and pollutant.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Polymer nanocomposites functionalised with nanocrystals of zeolitic imidazolate frameworks as ethylene control agents

  • Mahdi, E.M.
  • Cuadrado-Collados, Carlos
  • Silvestre-Albero, Joaquín
  • Tan, Jin-Chong
  • Silvestre-Albero, Joaquín|||/items/340b8128-2e1e-4869-8845-03b1802a1577
Ethylene (C2H4) management involves the usage of materials such as KMnO4 or processes such as ozone oxidation or combined photocatalysis/photochemistry. The ubiquity of C2H4, especially in an industrial context, necessitates a simpler and much more effective approach, and herein we propose the usage of tuneable polymer nanocomposites for the adsorption of C2H4 through the modification of the polymer matrices via the incorporation of nanocrystals of zeolitic imidazolate frameworks (nano-ZIFs). We demonstrate that the inclusion of ZIF-8 and ZIF-7 nanocrystals into polymeric matrices (Matrimid and polyurethane [PU]) yields robust nanocomposites that preserve the C2H4 adsorption/desorption capacity of nanocrystals while shielding it from degrading factors. We report new insights into the adsorption/desorption kinetics of the polymer and its corresponding nanocomposites, which can be tailored by exploiting the underlying polymeric molecular interactions. Importantly, we also elucidated the retention of the intrinsic structural framework dynamics of the nano-ZIFs even when embedded within the polymeric matrix, as evidenced from the breathing and gate-opening phenomena. Our findings pave the way for bespoke designs of novel polymer nanocomposites, which will subsequently impact the deployment of tailored nanomaterials for effective industrial applications.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Orally Administered Activated Charcoal as a Medical Countermeasure for Acute Radiation Syndrome in Rats

  • Snezhkova, Elisaveta
  • Rodionova, Natalia
  • Bilko, Dennis
  • Silvestre-Albero, Joaquín
  • Sydorenko, Alexey
  • Yurchenko, Olga
  • Pakharenko, Marharyta
  • Alavijeh, Mo
  • Bardakhivska, Kvitoslava
  • Riabchenko, Natalia
  • Nikolaev, Vladimir
  • Silvestre-Albero, Joaquín|||/items/340b8128-2e1e-4869-8845-03b1802a1577
Activated charcoal (AC) can be taken orally as enterosorbent for treatment of pathological states related to exogenous and endogenous intoxications. Synthesized granulated AC with a highly developed active surface (SBET ~2700 m2/g) was used as a medical countermeasure (MCM) to acute radiation sickness (ARS) in rats after total body X-ray irradiation. AC demonstrates positive results in ARS treatment, as expressed in, (i) a decrease in body weight loss, (ii) a protection of bone marrow (BM) cells colony formation capacity, (iii) a reduction of BM chromosomal aberrations and small intestine and spleen tissue damage, (iv) an amelioration of white blood cell count, and (v) a mitigation of superoxide ion generation rate in the liver. AC oral prescription seems to be perspective modality of ARS treatment.