Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 13
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Study of railway curve squeal in the time domain using a high-frequency vehicle/track interaction model

  • Giner Navarro, Juan|||0000-0002-0513-3625
  • Martínez Casas, José|||0000-0001-5706-4951
  • F. D. Denia|||0000-0003-4536-8610
  • Baeza González, Luis Miguel|||0000-0002-3815-8706
[EN] Railway curve squeal is an intense tonal and annoying type of noise commonly attributed to self-excited vibrations during curving. The mechanisms for its generation remain unclear and it is still a subject of discussion among researchers. Most of them have considered the falling behaviour of the friction coefficient with the slip velocity essential for reenergising the system. Recently, some authors have found that squeal can also appear even for constant friction coefficient through the wheel modal coupling between the normal and tangential directions caused by the wheel/rail contact. This paper particularly evaluates whether the latter mechanism is sufficient to find squeal in curving conditions. The introduction of flexibility in the railway subsystems is required to widen the domain to the high-frequency range in which squeal occurs. One single flexible and rotatory wheelset is considered and suitable forces are prescribed at the primary suspension seats in the current investigation. The rails are modelled through the Moving Element Method (MEM), permitting to extend the range of validity of beam models usually utilised in the literature. This work extends the formulation to rails supported by a viscoelastic Winkler bedding. Both wheelset and track models are coupled by means of a non-linear and unsteady wheel/rail contact model based on Kalker¿s Variational Theory. Simulation results for different track curvatures and friction coefficients are presented and discussed, showing tonal peaks in the tangential contact forces of the inner wheel. These results can be associated with squeal according to the characterisation of this phenomenon, indicating that squeal can be found in curving conditions using advanced dynamic interaction models even with constant friction coefficient., The authors gratefully acknowledge the financial support of Spanish Ministry of Economy, Industry and Competitiveness and the European Regional Development Fund (project TRA2017-84701-R), as well as Generalitat Valenciana (project Prometeo/2016/007) and European Commission through the project "RUN2Rail - Innovative RUNning gear soluTiOns for new dependable, sustainable, intelligent and comfortable RAIL vehicles" (Horizon 2020 Shift2Rail JU call 2017, grant number 777564).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Precision analysis and dynamic stability in the numerical solution of the two-dimensional wheel/rail tangential contact problem

  • Giménez, José Germán
  • Alonso Pazos, Asier
  • Baeza González, Luis Miguel|||0000-0002-3815-8706
[EN] In this paper the two-dimensional contact problem is analysed through different mesh topologies and strategies for approaching equations, namely; the collocation method, Galerkin, and the polynomial approach. The two-dimensional asymptotic problem (linear theory) associated with very small creepage (or infinite friction coefficient) is taken as a reference in order to analyse the numerical methods, and its solution is tackled in three different ways, namely steady-state problem, dynamic stability problem, and non-steady state problem in the frequency domain. In addition, two elastic displacements derivatives calculation methods are explored: analytic and finite differences. The results of this work establish the calculation conditions that are necessary to guarantee dynamic stability and the absence of numerical singularities, as well as the parameters for using the method that allows for maximum precision at the minimum computational cost to be reached., The authors gratefully acknowledge the financial support of the Spanish Ministry of Economy, Industry and Competitiveness and the European Regional Development Fund (project TRA2017-84701-R), as well as the European Commission through the projects 'RUN2Rail - Innovative RUNning gear soluTiOns for new dependable, sustainable, intelligent and comfortable RAIL vehicles' (Horizon 2020 Shift2Rail JU call 2017, grant number 777564) and 'PIVOT - Performance Improvement for Vehicles On Track' (Horizon 2020 Shift2Rail JU call 2017, grant number 777629).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Virtual test method of structure-borne sound for a metro bogie

  • Xie, Gang
  • Rissman, Martin
  • Bouvet, Pascal
  • Liu, Xiaowan
  • Thompson, David J.
  • Martín-Jarillo, Julián
  • López-Arteaga, Inés
  • Baeza González, Luis Miguel|||0000-0002-3815-8706
  • Esteve-Moreno, Juan José|||0000-0002-1259-7663
  • F. D. Denia|||0000-0003-4536-8610
  • Giner Navarro, Juan|||0000-0002-0513-3625
[EN] This paper presents a virtual test method for structure-borne noise generated from railway running gear. This method combines a number of existing tools to form a system approach. The wheelset and bogie frame are modelled using FEM software Nastran to include details of their construction. The primary springs are simplified to standard CBUSH elements in Nastran with point and transfer stiffness modelled by frequency-dependent complex stiffness, which are tuned against measurements. The wheel-rail contact forces due to roughness excitation are obtained by the wheel-rail interaction tool TWINS. The vibration of the full running gear is simulated in Nastran by applying the wheel-rail contact forces. The forces transmitted to the vehicle body through traction bars and dampers are calculated for predicting structure-borne noise., The work presented in this paper has received funding from the Shift2Rail Joint Undertaking under the European Union's Horizon 2020 research and innovation programme under grant agreement no. 777564. The contents of this publication only reflect the authors¿ view and the Joint Undertaking is not responsible for any use that may be made of the information contained in the paper. Provision of vehicle data from CAF Spain is gratefully acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Measurements and modelling of dynamic stiffness of a railway vehicle primary suspension element and its use in a structure-borne noise transmission model

  • Liu, Xiaowan
  • Thompson, David
  • Squicciarini, Giacomo
  • Rissmann, Martin
  • Bouvet, Pascal
  • Xie, Gang
  • Lopez Arteaga, Inés
  • Garralaga, Miguel A.
  • Chover, José A.
  • Martínez Casas, José|||0000-0001-5706-4951
  • Carballeira, Javier|||0000-0002-4179-8499
[EN] The noise inside railway vehicles is transmitted by both structure-borne and airborne paths and, although there are many sources, the rolling noise is often the most important. This paper focuses on the structure-borne transmission of rolling noise in a metro vehicle. Measurements are presented first of the vertical and lateral dynamic stiffness of a primary suspension element consisting of conical rubber/metal elements. Results are presented for various constant preloads over the frequency range 60600 Hz. An analytical model of the suspension element is also developed, based on a mass-spring system and including wave motion within the rubber elements. The dynamic stiffness results are used in a finite element model of the running gear, consisting of the bogie frame, wheelsets and suspension elements. The excitation is provided by the combined wheel/rail roughness at the contact point. This model is used to calculate the blocked forces at the connection points between the secondary suspension elements and the car body. The blocked forces are combined with measured vibro-acoustic transfer functions from these mounting points to the vehicle interior to determine the structure-borne noise inside the vehicle. The proposed methodology is validated against measurements during operation in terms of acceleration levels, blocked forces and structure-borne noise levels inside the vehicle, showing reasonably good agreement. Including the dynamic stiffness for the primary suspension leads to improved agreement between 100 and 500 Hz compared with using a constant stiffness., The work presented in this paper has received funding from the Shift2Rail Joint Undertaking under the European Union's Horizon 2020 research and innovation programme (grant agreement no. 777564). The contents of this publication only reflect the authors' views and the Joint Undertaking is not responsible for any use that may be made of the information contained in the paper.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Eulerian models of the rotating flexible wheelset for high frequency railway dynamics

  • Baeza González, Luis Miguel|||0000-0002-3815-8706
  • Giner Navarro, Juan|||0000-0002-0513-3625
  • Thompson, David J.
  • Monterde, Juan
[EN] In this paper three formulations based on an Eulerian approach are presented to obtain the dynamic response of an elastic solid of revolution, which rotates around its main axis at constant angular velocity. The formulations are especially suitable for the study of the interaction of a solid with a non-rotating structure, such as occurs in the coupled dynamics of a railway wheelset with the track. With respect to previous publications that may adopt similar hypotheses, this paper proposes morecompact formulations and eliminates certain numerical problems associated with the presence of second-order derivatives with respect to the spatial coordinates. Three different models are developed depending the basis function that represents the displacements associated with the deformation; these basis functions are: (1) the shape functions that are used in the three dimensional finite element (FE) method; (2) the undamped mode shapes of the solid; (3) the shape functions that are adopted in the axisymmetric FE approach. Comparisons are shown of calculations carried out using these models. These show the existence of modal veering when analysing the Campbell diagram for a railway wheel., The authors gratefully acknowledge the financial support of the European Commission through the project "RUN2Rail - Innovative RUNning gear soluTiOns for new dependable, sustainable, intelligent and comfortable RAIL vehicles" (Horizon 2020 Shift2Rail JU call 2017, grant number 777564), as well as Ministerio de Ciencia, Innovacion y Universidades and the European Regional Development Fund (projects TRA2017-84701-R and MTM2015-64013-P).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Analysis of the backward bending modes in damped rotating beams

  • Martínez Casas, José|||0000-0001-5706-4951
  • F. D. Denia|||0000-0003-4536-8610
  • Nadal, Enrique|||0000-0002-2808-298X
  • Giner Navarro, Juan|||0000-0002-0513-3625
  • Fayos Sancho, Juan
[EN] This article presents a study of the backward bending mode of a simply supported rotating Rayleigh beam with internal damping. The study analyses the natural frequency behaviour of the backward mode according to the internal viscous damping ratio, the slenderness of the beam and its spin speed. To date, the behaviour of the natural frequency of the backward mode is known to be a monotonically decreasing function with spin speed due to gyroscopic effects. In this article, however, it is shown that this behaviour of the natural frequency may not hold for certain damping and slenderness conditions, and reaches a minimum value (concave function) from which it begins to increase. Accordingly, the analytical expression of the spin speed for which the natural frequency of the backward mode attains the minimum value has been obtained. In addition, the internal damping ratio and slenderness intervals associated with such behaviour have been also provided., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: The authors gratefully acknowledge the financial support of Ministerio de Ciencia, Innovacion y Universidades Agencia Estatal de Investigacion and the European Regional Development Fund (project TRA2017-84701-R), as well as Generalitat Valenciana (project Prometeo/2016/007) and European Commission through the project 'RUN2Rail - Innovative RUNning gear soluTiOns for new dependable, sustainable, intelligent and comfortable RAIL vehicles' (Horizon 2020 Shift2Rail JU call 2017, grant number 777564)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Efficient decoupling technique applied to the numerical time integration of advanced interaction models for railway dynamics

  • Giner Navarro, Juan|||0000-0002-0513-3625
  • Martínez Casas, José|||0000-0001-5706-4951
  • F. D. Denia|||0000-0003-4536-8610
  • Baeza González, Luis Miguel|||0000-0002-3815-8706
[EN] Railway interaction is characterised by the coupling between the train and the track introduced through the wheel/rail contact. The introduction of the flexibility in the wheelset and the track through the finite element (FE) method in the last four decades has permitted to study high-frequency phenomena such as rolling noise and squeal, whose origin lies in the strongly non-steady state and non-linear behaviour of the contact forces that arise from the small contact area. In order to address models with a large number of degrees of freedom, innovative Eulerian-modal models for wheelsets with rotation and cyclic tracks have been developed in recent years. The aim of this paper is to extend the resulting formulation to an uncoupled linear matrix equation of motion that allows solving each equation independently for each time step, considerably reducing the associated computational cost. The decoupling integration method proposed is compared in terms of computational performance with Newmark and Runge-Kutta schemes, commonly used in vehicle dynamics, for simulations with the leading wheelset negotiating a tangent track and accounting the rail roughness., European Commission, Grant/Award Number: 777564; Generalitat Valenciana, Grant/Award Number: Prometeo/2016/007; Spanish Ministry of Economy, Industry, and Competitiveness and the European Regional Development Fund, Grant/Award Number: TRA2017¿84701¿R
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Method for obtaining the wheel-rail contact location and its application to the normal problem calculation through CONTACT

  • Baeza González, Luis Miguel|||0000-0002-3815-8706
  • F. D. Denia|||0000-0003-4536-8610
  • Thompson, David J.
  • Squicciarini, Giacomo
[EN] This work presents a robust methodology for calculating inter-penetration areas between railway wheel and rail surfaces, the profiles of which are defined by a series of points. The method allows general three-dimensional displacements of the wheelset to be considered, and its characteristics make it especially suitable for dynamic simulations where the wheel-rail contact is assumed to be flexible. The technique is based on the discretization of the geometries of the surfaces in contact, considering the wheel as a set of truncated cones and the rail as points. By means of this approach, it is possible to reduce the problem to the calculation of the intersections between cones and lines, the solution for which has a closed-form expression. The method has been used in conjunction with the CONTACT algorithm in order to solve the static normal contact problem when the lateral displacement of the wheelset, its yaw angle and the vertical force applied in the wheelset centroid are prescribed. The results consist of smooth functions when the dependent coordinates are represented as a function of the independent ones, lacking the jump discontinuities that are present when a rigid contact model is adopted. Example results are shown and assessed for the normal contact problem for different lateral and yaw positions of the wheelset on the track., This work was supported by the financial contribution of the European Union’s Shift2Rail programme (RUN2Rail project, grant number 777564), the Spanish Ministry of Economy, Industry and Competitiveness and the European Regional Development Fund (projects TRA2013-45596-C2-1-R and TRA2017-84701-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Extension of the modal superposition method for general damping applied in railway dynamics

  • Giner Navarro, Juan|||0000-0002-0513-3625
  • Martínez Casas, José|||0000-0001-5706-4951
  • F. D. Denia|||0000-0003-4536-8610
  • Andrés-Ruiz, Víctor Tomás
[EN] The frequency response function (FRF) permits to characterise in the frequency domain the systems governed by linear dynamics by means of a relationship between an excitation applied at one degree of freedom (dof) and the consequent output response in a particular dof. A modal approach is widely extended in the engineering fields as efficient method of computing the FRF of matrix second-order linear equations of motion derived from the application of the Finite Element Method (FEM) [1]. This approach is based on the truncation of the number of vibration modes that conform the base of the new modal coordinates. The criterion for the truncation is linked to the frequency range of the dynamic study, ordering the vibration modes with respect to the eigenvalues (the square of natural frequencies) associated. The natural frequency associated with the last vibration mode selected establishes the maximum frequency that can describe the time response of the system. The truncation permits to reduce the dimension of the system from N number of dofs in physical coordinates to m truncated vibration modes in modal coordinates. The fundamental numerical problem derived from the truncation is the resulting non-square vibration modes matrix, used as transformation matrix in the physical to modal change of variable [1,2]. This change should allow the diagonalisation of the matrices involved in the equation of motion: mass, stiffness and damping matrices. The diagonalisation is essential to decouple the system in m second-order linear differential equations that can be solved analytically in the time domain. Nevertheless, the inverse of vibration modes matrix required for the diagonalisation cannot be applied from its non-square nature and it can only be replaced by the transpose matrix if both mass and stiffness matrices are symmetric. The complexity increases in a case of general damping instead of proportional or spectral ones [3], in which the damping matrix must be included in the eigenproblem in order to diagonalise the whole modal system. This work proposes a methodology to overcome the issues abovementioned and applies this in the field of railway dynamics in order to compute the modal properties of a railway wheel modelled by using FEM [4]. The paper includes a study of the numerical performance of this method and its comparison with other numerical procedures to find the FRF of the wheel., The authors gratefully acknowledge the financial support of FEDER/Ministerio de Ciencia, Innovacion y Universidades Agencia Estatal de Investigacion (project TRA2017-84701-R), as well as Conselleria d¿Educacio, Investigacio, Cultura i Esport (project Prometeo/2016/007) and European Commission through the project RUN2Rail - Innovative RUNning gear soluTiOns for new dependable, sustainable, intelligent and comfortable RAIL vehicles (Horizon 2020 Shift2Rail JU call 2017, grant number 777564).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A framework to predict the airborne noise inside railway vehicles with application to rolling noise

  • Li, Hui
  • Thompson, David
  • Squicciarini, Giacomo
  • Liu, Xiaowan
  • Rissmann, Martin
  • Bouvet, Pascal
  • Martin Jarillo, Julian
  • Moreno Garcia-Loygorri, Juan
  • F. D. Denia|||0000-0003-4536-8610
  • Baeza González, Luis Miguel|||0000-0002-3815-8706
[EN] A framework is described for predicting the airborne noise inside railway vehicles which is applied to rolling noise sources. Statistical energy analysis (SEA) is used to predict the interior noise by subdividing the train cabin into several subsystems. The dissipation loss factors are obtained from the measured reverberation time in the train cabin. The power input to the interior SEA model is obtained from the external noise sources by multiplying the incident sound power on the external surfaces with measured transmission coefficients of the train floor and sidewalls. The sound power incident on the train floor is calculated by using an equivalent source model for the wheels and track together with an SEA model of the region below the floor. The incident sound power on the sides is obtained by using a waveguide boundary element (2.5D BE) method. The procedure is applied to a Spanish metro train vehicle running in the open field for which rolling noise is the main external noise source. The procedure is verified by field measurements of sound pressure beneath the carriage, on the sidewalls and inside the vehicle. The sensitivity of the results to changes in interior absorption is also studied, including the effect of passengers., This work has been funded by the China Scholarship Council and the RUN2Rail H2020/Shift2Rail project (Grant agreement No: 777564). The contents of this publication only reflect the authors' views and the Shift2Rail Joint Undertaking is not responsible for any use that may be made of the information contained in the pape
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Using a 2.5D boundary element model to predict the sound distribution on train external surfaces due to rolling noise

  • Li, Hui
  • Thompson, David
  • Squicciarini, Giacomo
  • Liu, Xiaowan
  • Rissmann, Martin
  • F. D. Denia|||0000-0003-4536-8610
  • Giner Navarro, Juan|||0000-0002-0513-3625
[EN] In order to be able to predict train interior noise, it is first important to calculate the external sound pressure distribution on the floor, sidewalls and roof. This can then be combined with the transmission loss of the train panels to determine the interior noise. Traditional techniques such as the finite element and boundary element (FE/BE) methods in three dimensions (3D) can achieve this result but are computationally very expensive. In this paper, a wavenumber-domain boundary element (2.5D BE) approach is instead adopted to predict the propagation of rolling noise from the wheels, rails and sleepers to the train external surfaces. In the 2.5D models, only the cross-section of the vehicle is represented by using boundary elements, while the third direction is considered in terms of a spectrum of wavenumbers. The rail is treated directly in the wavenumber domain but, to include the wheel, a method of representing point sources in a 2.5D approach is developed. An inverse Fourier transform is applied to obtain the spatial distribution of the sound pressure on the train surfaces. The validity of this approach has been verified by comparison with experimental data. The 2.5D BE method was first used to predict the sound distribution on a 1:5 scale train surfaces due to a point source below the vehicle, and later it was used to predict the sound pressure on a full-scale metro vehicle due to a loudspeaker. Comparisons of predictions with measurements on the scale model and on the metro vehicle showed good agreements. For a point source below the vehicle, the sound pressure levels on the train floor were found to be around 20 dB higher than on the sides, and the sound pressure on the train roof was negligible. The 2.5D BE method was also used to predict the sound pressure on the metro vehicle surfaces in running operation, in which the predicted sound pressure levels on the train external surfaces agreed with measurements to within 3 dB and similar trends were found in terms of spectra and longitudinal distribution of pressure., The work presented in this paper has received funding from China Scholarship Council and the Shift2Rail Joint Undertaking under the European Union's Horizon 2020 research and innovation programme (grant agreement no. 777564). The contents of this publication only reflect the authors' view and the Joint Undertaking is not responsible for any use that may be made of the information contained in the paper. The authors would also like to thank Dr. Hongseok Jeong for his assistance in the laboratory measurements and Metro de Madrid for assistance in the field tests. The authors are grateful to Dr. Xianying Zhang for providing the measured vibration of the 1:5 scale rail. All data published in this paper are openly available from the University of Southampton repository at 10.5258/SOTON/D1483
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Investigation of acoustic transmission beneath a railway vehicle by using statistical energy analysis and an equivalent source model

  • Li, Hui
  • Thompson, David
  • Squicciarini, Giacomo
  • Liu, Xiaowan
  • Rissmann, Martin
  • F. D. Denia|||0000-0003-4536-8610
  • Giner Navarro, Juan|||0000-0002-0513-3625
[EN] An approach is presented for modelling the noise propagation beneath the train floor and this is applied to rolling noise sources. It is assumed that the sound incident on the train floor is made up of a direct and a reverberant component. A combination of two numerical modelling approaches is considered to deal with these: an equivalent source model, to represent the direct component, and statistical energy analysis (SEA) for the reverberant part. In the equivalent source model, the wheel is replaced by monopole and dipole sources, which represent its radial and axial radiation. The rail vertical vibration and the sleepers are replaced by arrays of monopole sources while the rail lateral vibration is replaced by an array of lateral dipoles. The sound power of the rolling noise is obtained by using the TWINS model. In the SEA model, the region beneath the train floor is divided into several volumes and the power input to these subsystems is assumed to be due to the first reflections from the train floor and the ground. The reverberant and direct sound have very similar contributions to the total sound power incident on the train floor although this depends on how the equipment is arranged beneath the train. The modelling approach is verified by comparing the predicted sound pressure levels with laboratory measurements and with field tests., This work has been funded by the China Scholarship Council and the RUN2Rail H2020/Shift2Rail project (Grant agreement No: 777564). The contents of this publication only reflect the authors' views and the Shift2Rail Joint Undertaking is not responsible for any use that may be made of the information contained in the paper. The authors would also like to thank Dr. Hongseok Jeong for his assistance in the laboratory measurements and Metro de Madrid for assistance in the field tests. All data published in this paper are openly available from the University of Southampton repository at 10.5258/SOTON/D1552.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Study of the influence falling friction on the wheel/rail contact in railway dynamics

  • Giner Navarro, Juan|||0000-0002-0513-3625
  • Martínez Casas, José|||0000-0001-5706-4951
  • F. D. Denia|||0000-0003-4536-8610
  • Víctor Andrés-Ruiz
The complexity of the railway interaction comes from the coupling between the train and the track introduced through the forces appearing in the wheel/rail contact area. These forces are governed by the friction coefficient through the Coulomb s law, characterised by the static and kinematic values, although most of the contact models in railway dynamics consider a constant friction along the simulations. Nevertheless, it is well known that the friction coefficient falls with the slip velocity [1,2] from a maximum point determined by the static value to a point of saturation corresponding to the kinematic value. The question under debate is if the slope of this fall since recent test-rig experiments seem to reduce it ostensibly compared to friction curves generally estimated in the literature [3]. Rudd [4] proposed this negative slope as mechanism responsible for the generation of an instability phenomenon called railway curve squeal, which has received special attention from researchers [5 9]. The self-excited oscillations that characterise this phenomenon occur when the train is passing along a narrow curve, generating a strong tonal noise in the high-frequency domain. Although falling friction is the most widely accepted mechanism, other possibilities have been proposed to explain, getting more credit the mode-coupling mechanism [10 11]. For this instability, the oscillation frequencies of two structural modes of an undamped system come closer and closer together until they merge and a pair of an unstable and a stable mode results [12 13]. This work proposes a model based on a mass-spring-damper oscillator to evaluate its stability when submitted to a variable friction curve. Considering a single-d.o.f. (degrees of freedom) model, the paper studies the unstable conditions of the slip-dependent friction that can make the steady-state unstable. The study is extended to a two-d.o.f. case with two different geometric configurations in order to analyse the influence of the geometric coupling between the normal and tangential directions arisen from the contact and if it may instabilise the system even considering constant friction., The authors gratefully acknowledge the financial support of FEDER/Ministerio de Ciencia, Innovacion y Universidades Agencia Estatal de Investigacion (project TRA2017-84701-R), as well as Conselleria d'Educacio, Investigacio, Cultura i Esport (project Prometeo/2016/007) and European Commission through the project RUN2Rail - Innovative RUNning gear soluTiOns for new dependable, sustainable, intelligent and comfortable RAIL vehicles (Horizon 2020 Shift2Rail JU call 2017, grant number 777564).