Skip to main content

DESARROLLO DE UN MODELO INTEGRAL DE INTERACCION VEHICULO/VIA EN CURVA PARA LA REDUCCION DEL IMPACTO ACUSTICO DEL TRANSPORTE FERROVIARIO

TRA2017-84701-R

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2017
State Plan 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 18
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Study of railway curve squeal in the time domain using a high-frequency vehicle/track interaction model

  • Giner Navarro, Juan|||0000-0002-0513-3625
  • Martínez Casas, José|||0000-0001-5706-4951
  • F. D. Denia|||0000-0003-4536-8610
  • Baeza González, Luis Miguel|||0000-0002-3815-8706
[EN] Railway curve squeal is an intense tonal and annoying type of noise commonly attributed to self-excited vibrations during curving. The mechanisms for its generation remain unclear and it is still a subject of discussion among researchers. Most of them have considered the falling behaviour of the friction coefficient with the slip velocity essential for reenergising the system. Recently, some authors have found that squeal can also appear even for constant friction coefficient through the wheel modal coupling between the normal and tangential directions caused by the wheel/rail contact. This paper particularly evaluates whether the latter mechanism is sufficient to find squeal in curving conditions. The introduction of flexibility in the railway subsystems is required to widen the domain to the high-frequency range in which squeal occurs. One single flexible and rotatory wheelset is considered and suitable forces are prescribed at the primary suspension seats in the current investigation. The rails are modelled through the Moving Element Method (MEM), permitting to extend the range of validity of beam models usually utilised in the literature. This work extends the formulation to rails supported by a viscoelastic Winkler bedding. Both wheelset and track models are coupled by means of a non-linear and unsteady wheel/rail contact model based on Kalker¿s Variational Theory. Simulation results for different track curvatures and friction coefficients are presented and discussed, showing tonal peaks in the tangential contact forces of the inner wheel. These results can be associated with squeal according to the characterisation of this phenomenon, indicating that squeal can be found in curving conditions using advanced dynamic interaction models even with constant friction coefficient., The authors gratefully acknowledge the financial support of Spanish Ministry of Economy, Industry and Competitiveness and the European Regional Development Fund (project TRA2017-84701-R), as well as Generalitat Valenciana (project Prometeo/2016/007) and European Commission through the project "RUN2Rail - Innovative RUNning gear soluTiOns for new dependable, sustainable, intelligent and comfortable RAIL vehicles" (Horizon 2020 Shift2Rail JU call 2017, grant number 777564).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Precision analysis and dynamic stability in the numerical solution of the two-dimensional wheel/rail tangential contact problem

  • Giménez, José Germán
  • Alonso Pazos, Asier
  • Baeza González, Luis Miguel|||0000-0002-3815-8706
[EN] In this paper the two-dimensional contact problem is analysed through different mesh topologies and strategies for approaching equations, namely; the collocation method, Galerkin, and the polynomial approach. The two-dimensional asymptotic problem (linear theory) associated with very small creepage (or infinite friction coefficient) is taken as a reference in order to analyse the numerical methods, and its solution is tackled in three different ways, namely steady-state problem, dynamic stability problem, and non-steady state problem in the frequency domain. In addition, two elastic displacements derivatives calculation methods are explored: analytic and finite differences. The results of this work establish the calculation conditions that are necessary to guarantee dynamic stability and the absence of numerical singularities, as well as the parameters for using the method that allows for maximum precision at the minimum computational cost to be reached., The authors gratefully acknowledge the financial support of the Spanish Ministry of Economy, Industry and Competitiveness and the European Regional Development Fund (project TRA2017-84701-R), as well as the European Commission through the projects 'RUN2Rail - Innovative RUNning gear soluTiOns for new dependable, sustainable, intelligent and comfortable RAIL vehicles' (Horizon 2020 Shift2Rail JU call 2017, grant number 777564) and 'PIVOT - Performance Improvement for Vehicles On Track' (Horizon 2020 Shift2Rail JU call 2017, grant number 777629).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Tesis doctoral (DoctoralThesis)

Comprehensive dynamic models of railway wheelsets and tracks for the prediction of rolling noise

  • Andrés Ruiz, Víctor Tomás
[ES] El ruido de rodadura de vehículos ferroviarios presenta importantes desafíos en entornos urbanos y suburbanos, siendo precisa una comprensión integral de sus mecanismos subyacentes para una mitigación efectiva. Esta Tesis ofrece una investigación exhaustiva sobre la generación de ruido de rodadura, tanto en vías rectas como curvas, a través del desarrollo de modelos avanzados de alta frecuencia y herramientas de cálculo para una rigurosa predicción de niveles de ruido. El ruido de rodadura surge de la interacción entre las ruedas y los carriles en presencia de imperfecciones en sus superficies de contacto. Los principales componentes ferroviarios que contribuyen a la emisión acústica son las traviesas, los carriles y las ruedas. Las traviesas y los carriles están conectados por medio de las placas de asiento, mientras que las ruedas y los carriles están dinámicamente acoplados a través de su contacto. En consecuencia, cambios en cualquier componente pueden afectar al comportamiento dinámico y acústico del resto, subrayando la necesidad de un modelo integral para abordar eficazmente la radiación por ruido de rodadura. En esta Tesis se exploran y desarrollan diferentes modelos dinámicos de la vía y del eje montado. La vía, que se asume infinita, se describe utilizando la teoría de estructuras periódicas y se caracteriza por sus números y formas de onda. El eje montado se modeliza mediante el Método de Elementos Finitos y se caracteriza por sus frecuencias naturales y modos de vibración. La interacción rueda/carril se describe como una relación linealizada entre el movimiento relativo de ambos componentes y las fuerzas de contacto. Cabe indicar que los modelos explorados en este trabajo están formulados en el dominio de la frecuencia. Asimismo, se realiza un estudio de influencia del diseño de la vía en la radiación por ruido de rodadura, cuantificando los parámetros contribuyentes a la emisión acústica mediante técnicas estadísticas. Los resultados apuntan a que la geometría del carril tiene un impacto limitado en la radiación, mientras que las propiedades viscoelásticas de la vía, en particular la rigidez de la placa de asiento, desempeñan un papel fundamental en la generación de ruido. Es remarcable que, entre los distintos diseños, se han encontrado variaciones de hasta 7,4 dB(A) en la radiación acústica. Durante el desarrollo de esta investigación, se ha prestado atención al modelizado del eje montado. Su rotación se incluye usando coordenadas Eulerianas, lo que resulta un enfoque conveniente ya que el punto de contacto de la rueda con el carril permanece en una posición espacial constante. Dada la simetría axial de su geometría, la respuesta dinámica del eje montado se expande a lo largo de la dirección circunferencial mediante series de Fourier, lo que permite formular el comportamiento dinámico y acústico de este cuerpo tridimensional (3D) en un marco bidimensional (2D), resolviendo analíticamente la coordenada circunferencial. Esta metodología ofrece sin pérdida de generalidad una reducción del tiempo de cálculo computacional, lo que hace que el modelo sea idóneo para su integración en algoritmos de optimización. Por último, se realiza una investigación pionera sobre el ruido de rodadura cuando el vehículo negocia una curva. Si bien la curva está generalmente asociada con el ruido por chirridos, esta Tesis explora y confirma la importancia que también tiene el ruido de rodadura en estas condiciones. Para ello, se modelizan los efectos inerciales y giroscópicos que sufre un eje montado al describir una trayectoria curva. Además, diferentes fenómenos complejos que ocurren en el contacto rueda/carril, como por ejemplo el movimiento relativo entre estos elementos, se incorporan en el modelo de interacción. Los resultados indican que la posición del contacto rueda/carril sirve como un buen indicador del impacto que la negociación de una curva tiene en el ruido de rodadura., [CA] El soroll de rodament de vehicles ferroviaris presenta importants reptes en entorns urbans i suburbans, requerint una comprensió integral dels seus mecanismes subjacents per a una mitigació efectiva. Aquesta Tesi ofereix una investigació exhaustiva sobre la generació de soroll de rodament, tant en vies rectes com corbes, mitjançant el desenvolupament de models avançats d'alta freqüència i eines de càlcul per a la rigorosa predicció dels nivells de soroll radiat. El soroll de rodament sorgeix de la interacció entre les rodes i els carrils en presència d'imperfeccions en les seues superfícies de contacte. Els principals components ferroviaris que contribueixen a l'emissió acústica són les travesses, els carrils i les rodes. Les travesses i els carrils estan connectats a través de les plaques d'assentament, mentre que les rodes i els carrils estan acoblats mitjançant la seua interacció. En conseqüència, canvis en qualsevol component poden afectar al comportament dinàmic i acústic de la resta, subratllant la necessitat d'un model integral. En aquesta Tesi s'exploren i desenvolupen diversos models dinàmics de la via i de l'eix muntat. La via, que es considera infinita, es descriu utilitzant la teoria d'estructures periòdiques i es caracteritza pels seus números i formes d'ona. L'eix muntat es modelitza mitjançant el Mètode d'Elements Finits i es caracteritza per les seues freqüències naturals i modes de vibració. La interacció entre l'eix muntat i la via es descriu com una relació linealitzada entre el moviment relatiu d'ambdós components i les forces de contacte. Cal assenyalar que els models explorats en aquest treball estan formulats en el domini de la freqüència. Així mateix, es realitza un estudi d'influència del disseny de la via en la radiació, quantificant els paràmetres contribuents a l'emissió acústica mitjançant tècniques estadístiques. Els resultats apunten que la geometria del carril té un impacte limitat en la radiació sonora, mentre que les propietats viscoelàstiques de la via, en particular la rigidesa de la placa d'assentament, tenen un paper fonamental en la generació de soroll. És destacable que, entre els diferents dissenys, s'han trobat variacions de fins a 7,4 dB(A) en la radiació per soroll de rodament. Durant el desenvolupament d'aquesta investigació, s'ha prestat atenció al modelatge de l'eix muntat. La seua rotació s'inclou en la formulació utilitzant coordenades Eulerianes, la qual cosa resulta un enfocament convenient ja que el punt de contacte de la roda amb el carril roman en una posició constant. Donada la simetria axial de la seua geometria, la resposta dinàmica de l'eix muntat s'amplia al llarg de la direcció circumferencial mitjançant sèries de Fourier, permetent formular el comportament dinàmic i acústic d'aquest cos tridimensional (3D) en un marc bidimensional (2D), i resolent la coordenada circumferencial analíticament. Aquesta metodologia ofereix sense pèrdua de generalitat una reducció del temps de càlcul computacional, la qual cosa fa que el model siga idoni per a la seua integració en algoritmes d'optimització. Finalment, es realitza una investigació pionera sobre el soroll de rodament quan el vehicle negocia una corba. Si bé la corba està generalment associada amb el soroll per grinyols, aquesta Tesi explora i confirma la importància que també té el soroll de rodament en aquestes condicions. Per a això, es modelitzen els efectes inercials i giroscòpics que pateix un eix muntat al descriure una trajectòria corba. A més, diferents fenòmens complexes que ocorren en el contacte roda/carril, com el moviment relatiu entre aquests elements, s'incorporen en el model d'interacció. Els resultats indiquen que la posició del contacte roda/carril serveix com un bon indicador de l'impacte que la negociació d'una corba té en el soroll de rodament., [EN] Rolling noise emission in railway systems presents significant challenges in urban and suburban environments, requiring a comprehensive understanding of its underlying mechanisms for effective mitigation. This Thesis offers a thorough investigation into rolling noise generation, considering both tangent and curved tracks, through the development of advanced high-frequency models and calculation tools to predict noise levels accurately. Rolling noise arises from the interaction between railway wheels and tracks in the presence of roughness on their contact surfaces. The principal components contributing to the acoustic emission are the sleepers, rails, and wheels. Sleepers and rails are interconnected through rail pads, while wheels and rails are dynamically coupled due to their contact. Consequently, changes in any component might impact the dynamic and acoustic behaviour of all of them, outlining the necessity of a comprehensive model to address rolling noise radiation effectively. Various models for the track and wheelset are explored and developed in this Thesis. The track, assumed to be infinite, is described using periodic structure theory and it is characterised by its wavenumbers and waveshapes. The wheelset is modelled through the Finite Element Method (FEM) and it is characterised by its natural frequencies and vibration modes. The wheelset and track interaction is described as a linearised relationship between the relative motion of both components and the contact forces. The models examined in this work are formulated in the frequency domain. Identified track properties influencing rolling noise radiation are quantified using statistical techniques. While the rail geometry is found to have a limited impact on the total radiation, the viscoelastic properties of the track, particularly the rail pad stiffness, play a crucial role in noise generation. Variations up to 7.4 dB(A) were observed for different track designs. Special attention is devoted to the wheelset modelling in this Thesis. Its rotation is considered using Eulerian coordinates, a convenient approach as the wheel contact point with the rail remains at a constant spatial position. Given the axial symmetry of its geometry, the wheelset dynamic response is expanded around the circumferential direction using Fourier series, which yields a two-dimensional (2D) formulation of the dynamic and acoustic behaviour of this three-dimensional (3D) system, with the circumferential coordinate being solved analytically. This methodology, denoted as axisymmetric approach, offers a significant reduction in the associated computational calculation time while preserving accuracy, making the model well suited for its integration into optimisation algorithms. Lastly, a novel investigation into rolling noise when the vehicle negotiates a curve is conducted. While curved tracks are generally associated with squeal noise, this Thesis offers valuable insights into the importance of rolling noise as well. To achieve this, the inertial and gyroscopic effects associated with a wheelset running on a curve are modelled. Complex phenomena occurring at the wheel/rail contact, such as the relative motion between these two elements, are incorporated into the interaction model. The results indicate that the wheel/rail contact position serves as a reliable indicator of the impact of a curve on the rolling noise., This Thesis has been supported by Ministerio de Ciencia, Innovación y Universidades in the framework of the FPU grant program. Grants FPU18/03999, EST21/00213, and EST22/00353 as well as projects TRA2017-84701-R, PID2020-112886RA-I00, and PID2023-148483OB-I00 funded by MCIN/AEI/10.13039/501100011033, “ESF Investing in your future”, and “ERDF A way of making Europe” are acknowledged. The author also expresses his gratitude for the support provided by Programa PROMETEO/2021/046 of Generalitat Valenciana.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Optimized perforation schemes in railway wheels towards acoustic radiation mitigation

  • Gutiérrez-Gil, Jorge
  • García-Andrés, Francesc Xavier
  • Martínez Casas, José|||0000-0001-5706-4951
  • Nadal, Enrique|||0000-0002-2808-298X
  • F. D. Denia|||0000-0003-4536-8610
[EN] Rolling noise emitted by railway wheels is a problem that affects human health and limits the expansion of the railway network. It is caused by the wheel vibration due to the wheelrail contact force, and it is important in almost all the vehicle velocity range. The minimization of noise radiation associated with changes on the wheel web is discussed in this work, focusing on potential shape modifications in existing wheels in the form of a perforation distribution over the web. Such a post-manufacturing technique is a cost-effective solution that can be performed in a relatively short term. The implemented objective function is directly related to the overall radiated sound power, which is minimized using a genetic algorithmbased optimizer. In the acoustic model, radiation efficiencies are approximated to unity, the accuracy of this assumption being also studied in the work. The results reflect that an optimized distribution of perforations on the web of a railway wheel can reduce the total sound power level, by about 5 dB(A) and 2 dB(A) for curved and straight web, respectively. The mitigation of the radiated sound power is due to the fact that certain wheel vibration modes are modified and shifted to other frequencies where they are less excited. Finally, the relevance of the cross-sectional curvature of the web is explored by studying two different web geometries, suggesting that it can strongly influence the noise mitigation effects of the perforation pattern., The authors gratefully acknowledge the financial support of Ministerio de Ciencia, Innovacion y Universidades - Agencia Estatal de Investigacion, European Regional Development Fund (project TRA2017-84701-R), and Conselleria d'Educacio, Investigacio, Cultura i Esport (Generalitat Valenciana, project Prometeo/2016/007).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Eulerian models of the rotating flexible wheelset for high frequency railway dynamics

  • Baeza González, Luis Miguel|||0000-0002-3815-8706
  • Giner Navarro, Juan|||0000-0002-0513-3625
  • Thompson, David J.
  • Monterde, Juan
[EN] In this paper three formulations based on an Eulerian approach are presented to obtain the dynamic response of an elastic solid of revolution, which rotates around its main axis at constant angular velocity. The formulations are especially suitable for the study of the interaction of a solid with a non-rotating structure, such as occurs in the coupled dynamics of a railway wheelset with the track. With respect to previous publications that may adopt similar hypotheses, this paper proposes morecompact formulations and eliminates certain numerical problems associated with the presence of second-order derivatives with respect to the spatial coordinates. Three different models are developed depending the basis function that represents the displacements associated with the deformation; these basis functions are: (1) the shape functions that are used in the three dimensional finite element (FE) method; (2) the undamped mode shapes of the solid; (3) the shape functions that are adopted in the axisymmetric FE approach. Comparisons are shown of calculations carried out using these models. These show the existence of modal veering when analysing the Campbell diagram for a railway wheel., The authors gratefully acknowledge the financial support of the European Commission through the project "RUN2Rail - Innovative RUNning gear soluTiOns for new dependable, sustainable, intelligent and comfortable RAIL vehicles" (Horizon 2020 Shift2Rail JU call 2017, grant number 777564), as well as Ministerio de Ciencia, Innovacion y Universidades and the European Regional Development Fund (projects TRA2017-84701-R and MTM2015-64013-P).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Capítulo o parte de un libro (BookPart)

A vibroacoustic model of the stationary railway wheel for sound radiation prediction through an axisymmetric approach

  • Andrés Ruiz, Víctor
  • Denia Guzmán, Francisco
  • Martínez Casas, José|||0000-0001-5706-4951
  • Carballeira, Javier|||0000-0002-4179-8499
[EN] In the literature, different dynamic models of the railway wheel have been developed to predict its sound radiation; however, there are still certain aspects that can be improved. Specifically, the high computational cost of these models, either because they solve the fluidstructure interaction or because they solve the dynamics and acoustics of the three-dimensional wheel, makes it difficult to carry out numerous simulations with the aim of achieving quieter designs. In the present work, a vibroacoustic model of the stationary wheel is developed through an axisymmetric approach, yielding an efficient and comprehensive acoustic prediction tool. The calculation methodology consists of, firstly, adopting an axisymmetric approach to solve the vibratory dynamics of the wheel from its cross-section, using finite element techniques; subsequently, the acoustic radiation of the three-dimensional wheel is calculated from the dynamics of the aforementioned section through an analytical formulation. Finally, the vibroacoustic model developed is validated via comparison with commercial software that solves the fluid-structure interaction, showing the aforementioned computational advantages that the former has over the latter., The authors gratefully acknowledge the financial support of Agencia Estatal de Investigación and European Regional Development Fund (grant FPU18/03999, project TRA2017-84701-R and project PID2020-112886RA-I00).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Wheel shape optimization approaches to reduce railway rolling noise

  • García-Andrés, Francesc Xavier
  • Gutiérrez-Gil, Jorge
  • Martínez Casas, José|||0000-0001-5706-4951
  • F. D. Denia|||0000-0003-4536-8610
[EN] A wheel shape optimization of a railway wheel cross section by means of Genetic Algorithms (GAs) is presented with the aim of minimizing rolling noise radiation. Two different approaches have been implemented with this purpose, one centred on direct Sound poWer Level (SWL) minimization, calculated using TWINS methodology, and another one emphasizing computational efficiency, focused on natural frequencies maximization. Numerical simulations are carried out with a Finite Element Method (FEM) model using general axisymmetric elements. The design space is defined by a geometric parametrization of the wheel cross section with four parameters: wheel radius, a web thickness factor, fillet radius and web offset. For all wheel candidates a high-cycle fatigue analysis has been performed according to actual standards, in order to assure structural feasibility. Rolling noise reductions have been achieved, with a decrease of up to 5 dB(A) when considering the wheel component. Response surfaces have been also computed to study the dependency of the objective functions on the geometric parameters and to test the adequacy of the optimization algorithm applied., This study was financially supported by Ministerio de Ciencia, Innovacion y Universidades - Agencia Estatal de Investigacion, European Regional Development Fund (project TRA2017-84701-R), and Conselleria d'Educacio, Investigacio, Cultura i Esport (Generalitat Valenciana, project Prometeo/2016/007).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Analysis of the backward bending modes in damped rotating beams

  • Martínez Casas, José|||0000-0001-5706-4951
  • F. D. Denia|||0000-0003-4536-8610
  • Nadal, Enrique|||0000-0002-2808-298X
  • Giner Navarro, Juan|||0000-0002-0513-3625
  • Fayos Sancho, Juan
[EN] This article presents a study of the backward bending mode of a simply supported rotating Rayleigh beam with internal damping. The study analyses the natural frequency behaviour of the backward mode according to the internal viscous damping ratio, the slenderness of the beam and its spin speed. To date, the behaviour of the natural frequency of the backward mode is known to be a monotonically decreasing function with spin speed due to gyroscopic effects. In this article, however, it is shown that this behaviour of the natural frequency may not hold for certain damping and slenderness conditions, and reaches a minimum value (concave function) from which it begins to increase. Accordingly, the analytical expression of the spin speed for which the natural frequency of the backward mode attains the minimum value has been obtained. In addition, the internal damping ratio and slenderness intervals associated with such behaviour have been also provided., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: The authors gratefully acknowledge the financial support of Ministerio de Ciencia, Innovacion y Universidades Agencia Estatal de Investigacion and the European Regional Development Fund (project TRA2017-84701-R), as well as Generalitat Valenciana (project Prometeo/2016/007) and European Commission through the project 'RUN2Rail - Innovative RUNning gear soluTiOns for new dependable, sustainable, intelligent and comfortable RAIL vehicles' (Horizon 2020 Shift2Rail JU call 2017, grant number 777564)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Capítulo o parte de un libro (BookPart)

Railway rolling noise mitigation through optimal track design

  • Andrés Ruiz, Víctor
  • Denia Guzmán, Francisco
  • Thompson, D. J.
  • Martínez Casas, José|||0000-0001-5706-4951
  • Carballeira, Javier|||0000-0002-4179-8499
[EN] The main goal of the present work lies in the identification of the railway track properties that influence acoustic radiation, as well as in the analysis of these properties for the reduction of sound levels. This is achieved through a dynamic model of the railway wheel and track that allows the study of rolling noise, produced as a result of the wheel/rail interaction. Once the vibrational response of the railway components is determined, the sound power radiated by them is evaluated. The influence of the track properties on the sound radiation is determined by analysing the acoustic power results of different track configurations. From the results obtained, a number of guidelines are presented for noise mitigation of the involved railway elements. Between the worst and the best track design, there are differences of approximately 7.4 dB(A) in the radiation considering the wheel, rail and sleeper noise., The authors gratefully acknowledge the financial support of Agencia Estatal de Investigación and European Regional Development Fund (grant FPU18/03999, project TRA2017-84701-R and project PID2020-112886RA-I00)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Efficient decoupling technique applied to the numerical time integration of advanced interaction models for railway dynamics

  • Giner Navarro, Juan|||0000-0002-0513-3625
  • Martínez Casas, José|||0000-0001-5706-4951
  • F. D. Denia|||0000-0003-4536-8610
  • Baeza González, Luis Miguel|||0000-0002-3815-8706
[EN] Railway interaction is characterised by the coupling between the train and the track introduced through the wheel/rail contact. The introduction of the flexibility in the wheelset and the track through the finite element (FE) method in the last four decades has permitted to study high-frequency phenomena such as rolling noise and squeal, whose origin lies in the strongly non-steady state and non-linear behaviour of the contact forces that arise from the small contact area. In order to address models with a large number of degrees of freedom, innovative Eulerian-modal models for wheelsets with rotation and cyclic tracks have been developed in recent years. The aim of this paper is to extend the resulting formulation to an uncoupled linear matrix equation of motion that allows solving each equation independently for each time step, considerably reducing the associated computational cost. The decoupling integration method proposed is compared in terms of computational performance with Newmark and Runge-Kutta schemes, commonly used in vehicle dynamics, for simulations with the leading wheelset negotiating a tangent track and accounting the rail roughness., European Commission, Grant/Award Number: 777564; Generalitat Valenciana, Grant/Award Number: Prometeo/2016/007; Spanish Ministry of Economy, Industry, and Competitiveness and the European Regional Development Fund, Grant/Award Number: TRA2017¿84701¿R
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Method for obtaining the wheel-rail contact location and its application to the normal problem calculation through CONTACT

  • Baeza González, Luis Miguel|||0000-0002-3815-8706
  • F. D. Denia|||0000-0003-4536-8610
  • Thompson, David J.
  • Squicciarini, Giacomo
[EN] This work presents a robust methodology for calculating inter-penetration areas between railway wheel and rail surfaces, the profiles of which are defined by a series of points. The method allows general three-dimensional displacements of the wheelset to be considered, and its characteristics make it especially suitable for dynamic simulations where the wheel-rail contact is assumed to be flexible. The technique is based on the discretization of the geometries of the surfaces in contact, considering the wheel as a set of truncated cones and the rail as points. By means of this approach, it is possible to reduce the problem to the calculation of the intersections between cones and lines, the solution for which has a closed-form expression. The method has been used in conjunction with the CONTACT algorithm in order to solve the static normal contact problem when the lateral displacement of the wheelset, its yaw angle and the vertical force applied in the wheelset centroid are prescribed. The results consist of smooth functions when the dependent coordinates are represented as a function of the independent ones, lacking the jump discontinuities that are present when a rigid contact model is adopted. Example results are shown and assessed for the normal contact problem for different lateral and yaw positions of the wheelset on the track., This work was supported by the financial contribution of the European Union’s Shift2Rail programme (RUN2Rail project, grant number 777564), the Spanish Ministry of Economy, Industry and Competitiveness and the European Regional Development Fund (projects TRA2013-45596-C2-1-R and TRA2017-84701-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Capítulo o parte de un libro (BookPart)

Rolling noise reduction through GA-based wheel shape optimization techniques

  • Garcia-Andrés, Xavier
  • Gutiérrez-Gil, Jorge
  • Andrés, Víctor Tomás
  • Denia, Francisco David
  • Martínez Casas, José|||0000-0001-5706-4951
[EN] Railway rolling noise is nowadays a major source of acoustic pollution in urban areas, with nearly up to 12 million people daily affected in Europe by this phenomenon [1]. Hence, the search for ways of decreasing such noise radiation has become a highly active and significant research field. Following this approach, a Genetic Algorithms-based shape optimization of the railway wheel [2] is developed with the aim of minimizing rolling noise. Different approaches are considered to address the problem, such as directly minimizing radiated Sound poWer Level (SWL) or using the maximization of the natural frequencies if computational efficiency is especially critical. A parametric Finite Element model is implemented for the wheel based on the most relevant geometric parameters in rolling noise radiation. For the acoustic calculation, the sound radiation models used in the TWINS software [3] are adopted, which also accounts for the whole dynamics of the wheel/rail system. Furthermore, for every candidate wheel proposed, a structural analysis is computed in order to check design feasibility in accordance with the corresponding standard [4]. In all cases, new geometries for the wheel cross section are achieved that reduce the radiated rolling noise., This study has been supported by the Agencia Estatal de Investigación and the European Regional Development Fund (project TRA2017-84701-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Capítulo o parte de un libro (BookPart)

On the calculation of the Kalker&apos, s creep coefficients for non-elliptical contact areas

  • Gómez-Bosch, Jorge
  • Giner Navarro, Juan|||0000-0002-0513-3625
  • Carballeira, Javier|||0000-0002-4179-8499
[EN] FastSim is the most widely used tangential contact method due to its accuracy and computational efficiency. However, its use is limited to elliptic contact areas, as it needs results from Kalker’s Linear Theory, a Hertzian contact theory, to obtain the so-called elastic parameters. This makes FastSim unable to face some of the current railway challenges, such as wear, corrugation, Rolling Contact Fatigue (RCF), wheel flats, etc. Taking this limitation into account, in the present work, an alternative methodology to Kalker’s Linear Theory is proposed, which will enable FastSim to deal with non-Hertzian conditions., The authors gratefully acknowledge the financial support of Agencia Estatal de Investigación and European Regional Development Fund (grant PRE2018-084067 and project TRA2017-84701-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Efficient finite element modelling of sound propagation in after treatment devices with arbitrary cross section

  • F. D. Denia|||0000-0003-4536-8610
  • Sánchez-Orgaz, Eva María|||0000-0002-8864-3056
  • Martínez Casas, José|||0000-0001-5706-4951
  • Baeza González, Luis Miguel|||0000-0002-3815-8706
  • Ferrándiz-Catalá, Borja
[EN] The acoustic modelling of exhaust after-treatment devices, such as catalytic converters (CC) and diesel particulate filters (DPF), usually requires the use of multidimensional numerical techniques to assess the influence of higher order modes on the sound attenuation performance. Three-dimensional (3D) wave propagation can be considered through the finite element method (FEM). With a view to improving the computational expenditure of full 3D FEM, an efficient modelling technique is presented in this work to speed up transmission loss (TL) calculations in after-treatment devices with arbitrary cross section incorporating monoliths. The efficient modelling approach is based on the mode matching method, combining: (1) transversal pressure modes computed through a 2D FEM approach for devices with arbitrary but axially uniform cross section; (2) compatibility conditions of the acoustic fields at the device geometric discontinuities. For the acoustic modelling of monoliths, these are replaced by four pole transfer matrices relating the acoustic fields at both sides of the monolithic region. Mode matching TL results are compared with full 3D FE simulations and experimental measurements for some selected configurations, showing a good agreement. For a given accuracy, the computational efficiency of the mode matching technique proposed in this work improves that of full 3D FE calculations. TL improvements are achieved by suitable locations of a DPF inlet/outlet ducts. Next, a Genetic Algorithm (GA)-based optimization approach is used in order to improve the attenuation performance of the after-treatment device by varying the geometry as well as the monolith properties. Results show that the optimized configuration outperforms the initial design at target frequencies., The authors gratefully acknowledge the financial support of Ministerio de Ciencia, Innovación y Universidades-Agencia Estatal de Investigación through project TRA2017-84701-R and Generalitat Valenciana through project PROMETEO/2016/007.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Extension of the modal superposition method for general damping applied in railway dynamics

  • Giner Navarro, Juan|||0000-0002-0513-3625
  • Martínez Casas, José|||0000-0001-5706-4951
  • F. D. Denia|||0000-0003-4536-8610
  • Andrés-Ruiz, Víctor Tomás
[EN] The frequency response function (FRF) permits to characterise in the frequency domain the systems governed by linear dynamics by means of a relationship between an excitation applied at one degree of freedom (dof) and the consequent output response in a particular dof. A modal approach is widely extended in the engineering fields as efficient method of computing the FRF of matrix second-order linear equations of motion derived from the application of the Finite Element Method (FEM) [1]. This approach is based on the truncation of the number of vibration modes that conform the base of the new modal coordinates. The criterion for the truncation is linked to the frequency range of the dynamic study, ordering the vibration modes with respect to the eigenvalues (the square of natural frequencies) associated. The natural frequency associated with the last vibration mode selected establishes the maximum frequency that can describe the time response of the system. The truncation permits to reduce the dimension of the system from N number of dofs in physical coordinates to m truncated vibration modes in modal coordinates. The fundamental numerical problem derived from the truncation is the resulting non-square vibration modes matrix, used as transformation matrix in the physical to modal change of variable [1,2]. This change should allow the diagonalisation of the matrices involved in the equation of motion: mass, stiffness and damping matrices. The diagonalisation is essential to decouple the system in m second-order linear differential equations that can be solved analytically in the time domain. Nevertheless, the inverse of vibration modes matrix required for the diagonalisation cannot be applied from its non-square nature and it can only be replaced by the transpose matrix if both mass and stiffness matrices are symmetric. The complexity increases in a case of general damping instead of proportional or spectral ones [3], in which the damping matrix must be included in the eigenproblem in order to diagonalise the whole modal system. This work proposes a methodology to overcome the issues abovementioned and applies this in the field of railway dynamics in order to compute the modal properties of a railway wheel modelled by using FEM [4]. The paper includes a study of the numerical performance of this method and its comparison with other numerical procedures to find the FRF of the wheel., The authors gratefully acknowledge the financial support of FEDER/Ministerio de Ciencia, Innovacion y Universidades Agencia Estatal de Investigacion (project TRA2017-84701-R), as well as Conselleria d¿Educacio, Investigacio, Cultura i Esport (project Prometeo/2016/007) and European Commission through the project RUN2Rail - Innovative RUNning gear soluTiOns for new dependable, sustainable, intelligent and comfortable RAIL vehicles (Horizon 2020 Shift2Rail JU call 2017, grant number 777564).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Topology and shape optimization of dissipative and hybrid mufflers

  • Ferrándiz-Catalá, Borja
  • F. D. Denia|||0000-0003-4536-8610
  • Martínez Casas, José|||0000-0001-5706-4951
  • Nadal, Enrique|||0000-0002-2808-298X
  • Ródenas, Juan José|||0000-0003-2195-7920
[EN] This article presents a Topology Optimization (TO) method developed for maximizing the acoustic attenuation of a perforated dissipative muffler in the targeted frequency range by optimally distributing the absorbent material within the chamber. The Finite Element Method (FEM) is applied to the wave equation formulated in terms of acoustic pressure (chamber) and velocity potential (central duct, due to the existence of thermal gradients and mean flow) in order to evaluate the acoustic performance of the noise control device in terms of Transmission Loss (TL). Sound propagation through the chamber fibrous material is modelled considering complex equivalent acoustic properties, which vary spatially not only as a function of temperature, but also as a function of the lling density, since non-homogeneous density distributions are considered. The acoustic coupling at the perforated duct is performed by introducing a coordinate-dependent equivalent impedance. The objective function to maximize is expressed as the mean TL in the targeted frequency range. The sensitivities of this function with respect to the filling density of each element in the chamber are evaluated following the standard adjoint method. The Method of Moving Asymptotes (MMA) is used to update the design variables at each iteration of the TO process, keeping the weight of absorbent material equal or lower than a given value, while maximizing attenuation. Additionally, several particular designs inferred from the topology optimization results are analyzed. For example, the sizing optimization of a number of rings is carried out simultaneously with the aforementioned TO process (density layout). A reactive chamber is added in order to evaluate the TL of a hybrid muffler and its shape optimization is also carried out simultaneously with the aforementioned TO. Results show an increase in the muffler's mean TL at target frequencies, for all cases under study, while the amount of absorbent material used is maintained or even reduced.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Tesis doctoral (DoctoralThesis)

Development of innovative methodologies to reduce railway rolling noise through Genetic Algorithm-based shape optimization techniques

  • Garcia Andrés, Xavier
[ES] El ruido de rodadura es un fenómeno producido debido a la interacción entre la rueda y el carril e inducido por las pequeñas irregularidades existentes en la superficie de ambos. Dichas irregularidades, conocidas como "rugosidad", provocan que se genere una vibración tanto en la rueda como el carril cuando el tren circula a una cierta velocidad, lo que consecuentemente lleva a la aparición de radiación acústica. Esto conforma una de las fuentes de molestias más relevantes y principal origen de la contaminación acústica producida por los trenes al circular por regiones urbanas densamente pobladas. Así, el objetivo de esta Tesis es el desarrollo de una metodología integral para la obtención de diseños de rueda viables mediante el uso de Algoritmos Genéticos (AG) con la finalidad de minimizar el ruido de rodadura asociado. Al desarrollar los mencionados algoritmos de optimización, el Método de Elementos Finitos (MEF) se combina con la parametrización geométrica de las diferentes tipologías de diseño de rueda analizadas, descritas en función de aquellos parámetros más relevantes para la presente investigación. Se hace uso de modelos linealizados en el dominio de la frecuencia, capaces de resolver la dinámica completa del sistema a partir de las correspondientes mallas de la sección transversal. La obtención de la potencia acústica radiada se lleva a cabo mediante el empleo de una formulación semi-analítica para el cálculo de la eficiencia acústica de la rueda y al uso de un Modelo de Fuentes Equivalentes (MFE) en el carril. El desarrollo teórico, además, es validado con el software comercial de referencia en el campo de investigación, TWINS, en el cual se basa. A lo largo de los procedimientos de optimización, se realiza un análisis de fatiga en cada diseño de rueda considerado con el fin de asegurar su viabilidad estructural, lo que actúa como una restricción de "pena de muerte" en el algoritmo. Además, se desarrolla un procedimiento de identificación modal que permite caracterizar los modos de vibración y clasificarlos según su número de diámetros y circunferencias nodales. Seguidamente, se exploran dos formulaciones diferentes de la función objetivo: una centrada en reducir directamente el ruido radiado, llamada LA;W -min; i otra centrada en disminuir el ruido de rodadura maximizando la media de las frecuencias naturales de los modos de vibración, conocida como NF-max. En la metodología LA;W -min, se minimiza la suma en energía del nivel de potencia acústica expresado en dB(A). Para el caso de NF-max, se desplazan las frecuencias naturales a regiones de frecuencia donde la amplitud de rugosidad es menor. Se consideran diversas aproximaciones: la inclusión de esquemas de perforación y la modificación de la forma de su sección transversal. Además, también se ha estudiado la influencia en el ruido de la variación de las propiedades geométricas del carril y viscoelásticas de la vía. Como resultado de esta Tesis se han conseguido diversos modelos más silenciosos de rueda ferroviaria, con reducciones en el ruido de rodadura de hasta 5 dB(A). Cuando se considera el sistema ferroviario completo,se siguen consiguiendo mejoras en la potencia acústica radiada con los diseños de rueda resultantes. Además, se analizan las correlaciones entre la maximización de las frecuencias naturales y la atenuación del nivel de potencia acústica, estableciendo NF-max como una metodología adecuada para los casos en que se priorice la eficiencia computacional. La sensibilidad del problema a los espacios de diseño seleccionados y la adecuación del uso de AG se estudian también con la obtención de Superficies de Respuesta. Adicionalmente, se han establecido relaciones entre la variación de los parámetros geométricos y la disminución en la radiación acústica asociada, así como se ha propuesto la reubicación de los modos de vibración a lo largo del espectro en frecuencia com, [CA] El soroll de rodament és un fenomen causat per la interacció entre la roda i el carril i induït per les xicotetes irregularitats presents a les seues superfícies. Aquestes irregularitats, conegudes amb el nom de "rugositat", provoquen que es genere una vibració tant a la roda com al carril en circular el tren a una certa velocitat, el que conseqüentment du a l'aparició de radiació acústica. Açò conforma una de les fonts de molèsties més rellevants i el principal origen de la contaminació acústica generada pels trens al seu pas per regions urbanes densament poblades. Així, l'objectiu d'aquesta Tesi és el desenvolupament d'una metodologia integral per a l'obtenció de dissenys de roda viables mitjançant l'ús d'Algoritmes Genètics (AG) amb la inalitat de minimitzar el soroll de rodament associat. Al desenvolupar els esmentats algoritmes d'optimització, el Mètode d'Elements Finits (MEF) es combina amb la parametrització geomètrica de les diferents tipologies de disseny de roda analitzades, descrites en funció d'aquells paràmetres més rellevants per a aquesta investigació. Es fa ús de models linealitzats en el domini de la freqüència, capaços de resoldre la dinàmica completa del sistema a partir les corresponents malles de secció transversal. La obtenció de la potència acústica radiada es du a terme mitjançant la utilització d'una formulació semi-analítica per al càlcul de l'eficiència acústica de la roda i l'ús d'un Model de Fonts Equivalents (MFE) amb el carril. El desenvolupament teòric s'ha validat amb el software comercial de referència al camp d'investigació, TWINS, en el qual es basa. Al llarg dels procediments d'optimització, es realitza una anàlisi de fatiga a cada disseny de roda considerat amb la finalitat d'assegurar la seua viabilitat estructural. S'ha desenvolupat un procediment d'identificació modal que permet caracteritzar els modes de vibració i classificar-los d'acord al seu número de diàmetres i circumferències nodals. També, s'exploren dos formulacions diferents de la funció objectiu: una centrada en reduir directament el soroll radiat, anomenada LA;W -min; i altra centrada en disminuir el soroll de rodament maximitzant la mitja de les freqüències naturals dels modes de vibració, coneguda com NF-max. D'aquesta manera, en la metodologia LA;W -min, es minimitza la suma en energia del nivell de potència acústica expressat en dB(A). Per al cas de NF-max, es desplacen les freqüències naturals a regions de freqüència on l'amplitud de rugositat és menor. Es consideren diverses aproximacions: la inclusió d'esquemes de perforació i la modificació de la forma de la seua secció transversal, establint el radi com un valor fixe en un cas i utilitzant-lo com un paràmetre d'optimització més en l'altre. A més a més, s'ha estudiat la influència en el soroll de la variació de les propietats geomètriques del carril i viscoelàstiques de la via. Com a resultat d'aquesta Tesi s'han aconseguit diversos models de roda ferroviària més silenciosos, amb reduccions en el soroll de rodament de fins a 5 dB(A). Quan es considera el sistema ferroviari complet amb tots els seus components, es segueixen aconseguint millores en la potencia acústica radiada amb els dissenys de roda resultants. A més a més, 'analitzen les correlacions entre la maximització de les freqüències naturals i l'atenuació del nivell de potencia acústica, establint NF-max com una metodologia adequada pels casos en que es prioritza l'eficiència computacional. La sensibilitat del problema als espais de disseny escollits i l'adequació de l'ús de AG s'estudia també mitjançant l'obtenció de Superfícies de Resposta (SRs) per als paràmetres geomètrics utilitzats. Addicionalment, s'han establert relacions entre la variació dels paràmetres geomètrics i la disminució en la radiació acústica associada, així com s'ha proposat la reubicació dels modes de vibració al voltant de, [EN] Rolling noise phenomenon is produced due to the wheel/track interaction and induced by the small unevenness present in their surfaces. Such unevenness, known as "roughness", causes that vibrations arise in both the wheel and track when the train passes by with a certain speed, that consequently leads to the appearance of acoustic radiation. This kind of noise is one of the most relevant sources of annoyance and the principal focus of the railway acoustic pollution produced by trains operating through highly populated urban regions. Thus, the main goal of the present Thesis is the development of a comprehensive methodology to achieve suitable railway wheel designs through the use of Genetic Algorithms (GAs) with the aim of minimizing the associated rolling noise. When developing the aforementioned optimization algorithms, the Finite Element Method (FEM) is combined with the geometric parametrization of the different wheel design typologies analysed, described as a function of those parameters most relevant for the current research. In order to describe the dynamic behaviour of each component involved in the wheel/track interaction, use is made of linearised models in the frequency domain capable of solving the whole coupled dynamic response from the corresponding cross-section meshes. Subsequent derivation of the radiated sound power from the dynamic information is carried out by applying a semi-analytical formulation that allows for the wheel acoustic efficiency computation, on one hand, and by making use of an Equivalent Sources Model (ESM) in the track, on the other hand. Besides, such theoretical development is validated with the reference commercial software in the field, TWINS, on which it is based. Throughout the optimization procedures, a fatigue analysis is performed on every wheel design considered to assure structural feasibility, that acts as a "death penalty" constraint in the algorithm. Furthermore, a modal identification procedure is developed, which allows to characterize modeshapes and to classify them according to their number of nodal diameters and circumferences. Then, two different formulations of the objective function are explored: one focused on directly reducing radiated noise, named LA;W-min; and another centred on decreasing rolling noise by maximizing the average natural frequency of the modeshapes, called NF-max. Hence, in the LA;W -min methodology, the sum in energy of the wheel Sound poWer Level (SWL) expressed in dB(A) is minimized. For the NF-max case, natural frequencies are shifted to frequency regions where the roughness amplitude content is lower. Different approaches are considered: the inclusion of perforation schemes in the wheel and the variation of its cross-sectional shape, setting the radius as a constant value in one case and using it as an optimization parameter in another. Moreover, the influence on the noise of changing the rail geometric and track viscoelastic properties is also studied. As a result of the present Thesis, several quieter models of railway wheels have been achieved, with rolling noise reductions of up to 5 dB(A). When the whole railway system with all the components is considered, improvements in the radiated sound power remain achieved with the resulting wheel designs. Besides, correlations between maximization of natural frequencies and SWL mitigation are analysed, establishing the NF-max as a suitable methodology for cases when computational efficiency is prioritized. The sensitivity of the problem to selected design domains and the suitability of the use of GAs are also studied with the obtention of Response Surfaces (RSs) for the geometric parameters used. Additionally, correlations are established between the variation of the geometric parameters and the decrease in the associated acoustic radiation, while the shifting of the modeshapes along the frequency domain is proposed as a physical mechanism responsible of the observed sound power decrease., This thesis has been supported by the Agencia Estatal de Investigación and the European Regional Development Fund (projects TRA2013-45596-C2-1-R and TRA2017-84701-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Study of the influence falling friction on the wheel/rail contact in railway dynamics

  • Giner Navarro, Juan|||0000-0002-0513-3625
  • Martínez Casas, José|||0000-0001-5706-4951
  • F. D. Denia|||0000-0003-4536-8610
  • Víctor Andrés-Ruiz
The complexity of the railway interaction comes from the coupling between the train and the track introduced through the forces appearing in the wheel/rail contact area. These forces are governed by the friction coefficient through the Coulomb s law, characterised by the static and kinematic values, although most of the contact models in railway dynamics consider a constant friction along the simulations. Nevertheless, it is well known that the friction coefficient falls with the slip velocity [1,2] from a maximum point determined by the static value to a point of saturation corresponding to the kinematic value. The question under debate is if the slope of this fall since recent test-rig experiments seem to reduce it ostensibly compared to friction curves generally estimated in the literature [3]. Rudd [4] proposed this negative slope as mechanism responsible for the generation of an instability phenomenon called railway curve squeal, which has received special attention from researchers [5 9]. The self-excited oscillations that characterise this phenomenon occur when the train is passing along a narrow curve, generating a strong tonal noise in the high-frequency domain. Although falling friction is the most widely accepted mechanism, other possibilities have been proposed to explain, getting more credit the mode-coupling mechanism [10 11]. For this instability, the oscillation frequencies of two structural modes of an undamped system come closer and closer together until they merge and a pair of an unstable and a stable mode results [12 13]. This work proposes a model based on a mass-spring-damper oscillator to evaluate its stability when submitted to a variable friction curve. Considering a single-d.o.f. (degrees of freedom) model, the paper studies the unstable conditions of the slip-dependent friction that can make the steady-state unstable. The study is extended to a two-d.o.f. case with two different geometric configurations in order to analyse the influence of the geometric coupling between the normal and tangential directions arisen from the contact and if it may instabilise the system even considering constant friction., The authors gratefully acknowledge the financial support of FEDER/Ministerio de Ciencia, Innovacion y Universidades Agencia Estatal de Investigacion (project TRA2017-84701-R), as well as Conselleria d'Educacio, Investigacio, Cultura i Esport (project Prometeo/2016/007) and European Commission through the project RUN2Rail - Innovative RUNning gear soluTiOns for new dependable, sustainable, intelligent and comfortable RAIL vehicles (Horizon 2020 Shift2Rail JU call 2017, grant number 777564).