Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 12
Encontrada(s) 1 página(s)

Biblos-e Archivo. Repositorio Institucional de la UAM
Publication Artículo científico (JournalArticle)

Folded W-band waveguide filters with resonant coupling apertures for the generation of additional transmission zeros

  • Miek, Daniel
  • Höft, Michael
  • Morán López, Ana
  • Ruiz Cruz, Jorge Alfonso
Título del postprint: Realization of folded W-band waveguide filters with multiple resonant transmission zeros, In this paper the realization of multiple additional transmission zeros in folded W-band waveguide filters is discussed. The transmission zeros (TZs) can be placed symmetrically as well as asymmetrically in the near passband region of the filter and arise due to a resonant coupling between source and / or load. Third and fourth order filter set-ups are presented, showing in total between three and six TZs. These zeros can be used to improve the selectivity of the filter without increasing the overall order. The filter design and realization process is discussed. Subsequently, the measurement results are compared with simulation, showing good agreement. As the filters are designed for the W-band, the manufacturing process is connected with some difficulties which are addressed within this paper as well, This project has received funding from the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No 811232. This work was partially supported by the Spanish Government under Grant TEC2016-76070-C3-1-R (AEI/FEDER, UE)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Miniaturized Ultra-Wideband Bandpass Filter Based on Substrate Integrated Quasi-Lumped Resonators

  • Messaoudi, El Mehdi
  • Martínez Pérez, Jorge Daniel|||0000-0002-7119-3714
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] A compact ultra-wideband bandpass filter employing substrate integrated quasi-lumped resonators is presented in this paper. A multi-layer hybrid structure is proposed, combining quasi-lumped resonators and surface mount components. This allows a huge miniaturization degree due to the high capacitive loading. Moreover, strong magnetic and electric couplings can be implemented thus enabling the introduction of transmission zeros for improving response selectivity. A filter example centered at 5.35 GHz with a prescribed channel bandwidth of 2.9 GHz has been designed, manufactured and measured. The filter size is smaller than 7×7 mm2. The obtained results show the feasibility of the proposed approach., This project has received funding from the European Union Horizon 2020 research and innovation programme under the Marie Sklodowska-Curie grant agreement No. 811232, the European Space Agency (ESA) under contract 4000124983, and the Ministerio de Ciencia e Innovación (Spanish Government) under project PID2019-103982R-C41
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Using Dielectric Rods to Reconfigure Combline Filters in Center Frequency and Bandwidth

  • Sharma, Abhishek
  • Guglielmi, Marco
  • Cogollos, Santiago|||0000-0002-4189-2952
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] This article describes the use of dielectric rods to reconfigure combline filters both with respect to center frequency and bandwidth. In this context, a new filter topology is developed in order to maximize the achievable reconfiguration range. The design of a prototype is discussed in detail, clearly demonstrating the feasibility of center frequency and bandwidth reconfiguration, with the same filter structure, while maintaining an equiripple return loss. In addition to theory, a combline filter prototype is also fabricated, tuned and measured in several configurations showing excellent agreement with simulations, thereby fully validating both the basic concept and the design procedure, This work was supported in part by the European Union's Horizon 2020 Research and Innovation Program through the Marie Sklodowska-Curie Innovative Training Networks (ITN) (TESLA) under Grant 811232; and in part by the Minsiterio de Ciencia e Innovacion (MICIN), Spanish Government, through the Research and Development Project under Grant PID2019-103982RB-C41 (funded by MICIN/AEI/10.13039/501100011033).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Remote Reconfiguration of Microwave Filters Using Dielectric Tuners

  • Sharma, Abhishek
  • Ossorio, Javier
  • Smacchia, Davide
  • Tronser, Tillman
  • Guglielmi, Marco
  • Cogollos, Santiago|||0000-0002-4189-2952
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] The objective of this article is to explore the use of dielectrics to reconfigure remotely microwave filters in rectangular waveguide. To start, we study experimentally the phase shift that is achievable using dielectric tuning elements in a rectangular waveguide. We then compare the results obtained with the performance of standard metallic tuning cylinders and screws. Next, the passive intermodulation (PIM) behavior of dielectric tuning elements is investigated experimentally. The PIM results obtained using dielectrics are then compared with the ones of metallic tuning elements. After that, the measured results for a filter tuned with a number of different dielectric tuning elements are discussed to identify the required relation between cavity size, dielectric constant, and tuner diameter. As a proof of concept, we then design, manufacture, and test two filters, one in WR75 and the other in WR90. Both simulated and measured results are then presented clearly demonstrating that the structures discussed can indeed be reconfigured (or tuned) both in terms of filter center frequency and bandwidth. Finally, computer-driven linear actuators are connected to the dielectric tuners, and the remote tuning capability is successfully demonstrated., This work was supported in part by the European Union's Horizon 2020 Research and Innovation Program, through the Marie Sklodowska-Curie ITN (TESLA) under Grant 811232 and in part by the Minsiterio de Ciencia e Innovacion (MICIN, Spanish Government) through the Research and Development Project under Grant PID2019-103982RB-C41 (funded by MICIN/AEI/10.13039/501100011033).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Compact Substrate Integrated Waveguide Wideband Bandpass Filter With Post-Manufacturing Tuning Capabilities

  • Messaoudi, El Mehdi
  • Martínez Pérez, Jorge Daniel|||0000-0002-7119-3714
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] In this paper, a miniaturized wideband bandpass filter in coaxial substrate integrated waveguide (SIW) technology is presented. To improve the response selectivity and coupling control, a multi-layer structure has been implemented, introducing both strong magnetic and electric couplings. To reduce the physical size of the device, surfaced-mounted device (SMD) capacitors have been integrated on the top layer. These allow both resonant frequency and capacitive coupling level control. Thus, a 4-th order Chebyshev filter with an absolute bandwidth (BW) of 2.9 GHz centered at 5.35 GHz has been designed, fabricated and measured. An extremely small filter size of 7 x 7 mm(2) has been obtained. A study of manufacturing tolerances are also presented in this paper, together with a post-manufacturing response correction allowed by the SMD elements. As it is shown in the paper, the filter's out-of-band rejection can be easily enhanced by introducing additional transmission zeros (TZs)., This work was supported in part by the European's Union Horizon 2020 Research and Innovation Programme under the MarieSklodowska-Curie Innovative Triangle Networks (ITN) through TESLA under Grant 811232, in part by the European Space Agency(ESA) under Contract 4000124983, in part by the Ministerio de Ciencia e Innovacion (MICIN) through Spanish Government under the Research and Development Project PID2019-103982R-C41 and Project MICIN/AEI/10.13039/501100011033, and in part by the funding for open access charge: Universitat Politecnica de Valencia
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Analysis and design of re-configurable combline filters using dielectric tuners

  • Sharma, Abhishek
  • Guglielmi, Marco
  • Cogollos, Santiago|||0000-0002-4189-2952
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] This article describes different tunable structures for typical waveguide combline filters. In this context, several configurations using dielectric tuners have been studied for resonators, inter-resonator couplings, and input/output couplings. All configurations are analyzed in a wide frequency range showing advantages and drawbacks. Using the best structures in terms of performance, a fully re-configurable filter has been designed. The filter provides a wide tuning range in terms of center frequency while maintaining a high Q factor, and a constant bandwidth and return losses. A first filter prototype has been designed at L-band. The structure demonstrates a tunability in terms of frequency range of about 400 %, thereby clearly demonstrating that the approach we propose is indeed a very promising candidate for implementing tunable combline filters based on dielectric tuners.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Integrating multiple stubs in stepped-impedance filter aiming for high selectivity

  • Sami, Abdul
  • Gómez Laso, Miguel Ángel
  • Lopetegui Beregaña, José María
  • Arnedo Gil, Israel
  • Calero Fernández, Ibai
  • Teberio Berdún, Fernando
  • Martín Iglesias, Petronilo
  • Benito Pertusa, David
  • Arregui Padilla, Iván
A design technique to include multiple and fully-controlled transmission zeros (TZs) in the frequency response of rectangular waveguide commensurate-line stepped-impedance filters is presented in this letter. These bandpass filters (BPFs) are known for having reduced sensitivities against manufacturing inaccuracies and are composed of multiple waveguide sections. In order to improve their selectivity, 3λg/4 and λg/4-stubs are included to create multiple TZs around the passband. The proposed technique allows us to add multiple stubs in a single section and, therefore, only minor adjustments in the affected part of the filter are required, which simplifies the overall design process. The technique has been verified with a design example with four TZs (two on each side) near the passband., This work was supported by the Spanish Ministerio de Ciencia e Innovación –Agencia Estatal de Investigación (MCIN/AEI/10.13039/501100011033) under Project PID2020-112545RB-C53 and by the European Union’s Horizon 2020 Research and Innovation Program under Grant 811232-TESLA-H2020-MSCA-ITN-2018.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Multipactor breakdown analysis of Ku-band meandered low-pass filter

  • Sami, Abdul
  • Teberio Berdún, Fernando
  • Arnedo Gil, Israel
  • Martín Iglesias, Petronilo
  • Lopetegui Beregaña, José María
  • Gómez Laso, Miguel Ángel
  • Arregui Padilla, Iván
In this work, a very compact rectangular waveguide low-pass filter with meandered topology based on commensurate lines for Ku-band satellite applications is analysed for high-power handling capabilities. The device consists of rectangular waveguide sections properly cascaded to form a meandered topology to obtain the desired value of the local reflection coefficients. which are essential to achieve the target frequency response and also to keep large mechanical gaps. Hence, this technique allows us not only to design a filter with compact size but a filter geometry which is suitable for high power applications. In the paper, the low-pass filter based on commensurate lines is first designed by cascading E-plane mitered bends (±90° EMBs) in CST Microwave Studio (MWS) and then the values of the electromagnetic fields at the passband frequencies are exported to Spark3D to perform a multipactor analysis. The critical areas inside the device where the multipactor discharge occurs will also be identified in the high-power analysis., This work was supported by the Spanish Ministerio de Ciencia e Innovación –Agencia Estatal de Investigación (MCIN/AEI/10.13039/501100011033) under Project PID2020-112545RB-C53 and by the European Union’s Horizon 2020 Research and Innovation Program under Grant 811232-TESLA-H2020-MSCA-ITN-2018.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Tesis doctoral (DoctoralThesis)

Microwave and millimeter-wave components aiming for an easy fabrication

  • Sami, Abdul
This Thesis is intended to develop various novel design techniques to design low-pass and band-pass waveguide filters based on stepped-impedance commensurate lines for various satellite applications. The main objectives of the thesis are to design waveguide filters which are more robust against fabrication errors, with high electrical performance, reduced size and capable of high-power operations. Keeping in mind the objectives of the thesis, the inherent low-pass response of the commensurate line waveguide sections is utilized to design a low-pass filter with meandered topology employing E-plane mitered bends with constant widths to achieve a very compact design for Ku-band but with large mechanical gaps to make the filter design capable for high power operations. The high-power handling capabilities are demonstrated with SPARK3D at various frequencies between 10.7 GHz to 11.7 GHz in the passband in the pass-band. The estimated minimum input threshold power is 20 kW at the highest frequency of the passband. Also, the critical areas inside the filter structures are also identified which are considered to be more prone to multipactor discharge to identify the key design parameters for enhancing the power handling capabilities., This work was supported by the European Union’s Horizon 2020 Research and Innovation Program under Grant 811232-TESLA-H2020-MSCA-ITN-2018, Programa de Doctorado en Tecnologías de las Comunicaciones, Bioingeniería y de las Energías Renovables (RD 99/2011), Bioingeniaritzako eta Komunikazioen eta Energia Berriztagarrien Teknologietako Doktoretza Programa Ofiziala (ED 99/2011)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Improvement of corona breakdown threshold (peak power handling) in smooth-profiled microstrip filters

  • Ahmad, Jamil
  • Hussain, Jabir
  • Arregui Padilla, Iván
  • Martín Iglesias, Petronilo
  • Arnedo Gil, Israel
  • Gómez Laso, Miguel Ángel
  • Lopetegui Beregaña, José María
Trabajo presentado al International Workshop on Multipactor, Corona and Passive Intermodulation (MULCOPIM), Valencia, Spain, 19-21 October 2022 (Session 08), In this paper, the PPHCs of two filter design techniques, stepped-impedance (SI) and smooth-profile (SP), are presented for four design prototypes. Smooth-profiled filters feature smooth variations in the characteristic impedance profile, avoiding sharp edges, which accumulate electric fields. The absence of sharp edges in SP reduces the voltage magnification factor, which in turn improves the PPHC of the filter. The phenomenon of electric fields accumulation at the sharp corners of the SI filters is presented and compared with smooth transitions in SP filters. Furthermore, 1D graphs of electric field intensity are presented along the strip contour of the microstrip lines. Finally, SPARK3D results clearly demonstrate that SP filters can handle higher peak powers than their SI counterparts between critical pressure and ambient pressure, for all the studied designs., This work was supported by the Spanish Ministerio de Ciencia e Innovación –Agencia Estatal de Investigación (MCIN/AEI/10.13039/501100011033) under Project PID2020-112545RB-C53 and by the European Union's Horizon 2020 Research and Innovation Program under Grant 811232-TESLA-H2020-MSCA-ITN-2018. Jamil Ahmad also acknowledges the funding received through the PRE2018-085491 grant.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Synthesis of rectangular waveguide filters with smooth profile oriented to direct metal additive manufacturing

  • Percaz Ciriza, Jon Mikel
  • Hussain, Jabir
  • Arregui Padilla, Iván
  • Teberio Berdún, Fernando
  • Benito Pertusa, David
  • Martín Iglesias, Petronilo
  • Arnedo Gil, Israel
  • Gómez Laso, Miguel Ángel
  • Lopetegui Beregaña, José María
In this paper, a novel design method for rectangular waveguide filters intended for fabrication using direct metal additive manufacturing is proposed. The synthesized filters will feature a smooth profile that allows us to fabricate them orienting the filter propagation axis in the vertical building direction, achieving an optimum configuration for direct metal additive manufacturing fabrication. The novel design method is valid for any all-pole transfer function, which is initially implemented with a commensurate-line distributed unit element prototype. The impulse response of that initial prototype is then properly interpolated to obtain the target response for a smooth-profiled filter with similar length and profile excursion. Finally, the target impulse response just generated is implemented in rectangular waveguide technology employing a novel inverse scattering synthesis technique that relies on the coupled-mode theory to model the electromagnetic behavior of the waveguide filter. The novel inverse scattering synthesis technique is general and also valid for the case of filters with very high rejection levels, which is of great relevance in rectangular waveguide technology. A Ku-band low-pass filter with stringent satellite specifications is designed using the proposed method, fabricated by means of a direct metal additive manufacturing technique, and measured with a vector network analyzer. A very good agreement is achieved between the simulated and measured results, fulfilling the required specifications and demonstrating the feasibility and performance of the novel design method., This work was supported in part by the Spanish Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (MCIN/AEI/10.13039/ 501100011033) under Project TEC2017-85529-C3-2-R (co-funded by the Fondo Europeo de Desarrollo Regional (FEDER) “A way to make Europe”) and Project PID2020-112545RB-C53, and in part by the Advanced Technologies for future European Satellite Applications (TESLA) Project (European Union’s Horizon 2020 Research and Innovation Programme through the Marie Sklodowska-Curie Grant) under Grant 811232.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Robust tolerance design of bandpass filter with improved frequency response for Q-band satellite applications

  • Sami, Abdul
  • Teberio Berdún, Fernando
  • Miranda Santafé, Luis
  • Arnedo Gil, Israel
  • Martín Iglesias, Petronilo
  • Benito Pertusa, David
  • Lopetegui Beregaña, José María
  • Gómez Laso, Miguel Ángel
  • Arregui Padilla, Iván
A rectangular waveguide bandpass filter for Q-band with simple fabrication is proposed in this letter. The design is based on the use of the first passband replica of commensurate-line stepped-impedance structures and achieves the suppression of their inherent low-pass response. In order to do it, the filter is implemented by rectangular waveguide sections with different widths and heights that can be analytically calculated. The technique is validated by a 9th order Chebyshev filter with passband between 40 and 43 GHz and fabrication yield equal to 84 % for a manufacturing error of ± 20 μm. The measured results of the prototype fabricated with CNC milling are in good agreement with the simulated ones., This work was supported by the Spanish Ministerio de Ciencia, Innovación y Universidades–Agencia Estatal de Investigación under Project TEC2017-85529-C3-2-R (AEI, FEDER-EU) and by the European Union’s Horizon 2020 research and innovation programme under grant agreement no. 811232-TESLA-H2020-MSCA-ITN-2018.