Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 9
Encontrada(s) 1 página(s)

Addi. Archivo Digital para la Docencia y la Investigación
Publication Artículo científico (JournalArticle)

Poly(vinyl benzoate)-b-poly(diallyldimethyl ammonium TFSI)-b-poly(vinyl benzoate) Triblock Copolymer Electrolytes for Sodium Batteries

  • Stigliano, Pierre L.
  • Gallastegui, Antonela
  • Villacís Segovia, Carlos
  • Amores, Marco
  • Kumar, Ajit
  • O’Dell, Luke A.
  • Fang, Jian
  • Mecerreyes Molero, David
  • Pozo Gonzalo, Cristina
  • Forsyth, Maria
Block copolymers (BCPs) as solid electrolytes for batteries are usually designed to have an ion-solvating block for ion conduction and an ionophobic block for providing mechanical strength. Here, we show a novel solid polymer electrolyte (SPE) for sodium batteries based on a poly(vinyl benzoate)-b-poly(diallyldimethyl ammonium bis(trifluoromethanesulfonyl)imide) PVBx-b-PDADMATFSIy-b-PVBx ABA triblock copolymer. The SPE triblock copolymer comprises a polymerized ionic liquid (PIL) ion-solvating block combined with NaFSI salt as an internal block and an ionophilic PVB as an external block. Four distinct compositions with varying chain lengths of the blocks were synthesized by reversible addition−fragmentation chain-transfer (RAFT) polymerization. The neat copolymers were subsequently mixed with NaFSI in a 2:1 mol ratio of Na to ionic monomer units. Through comprehensive analysis using differential scanning calorimetry (DSC), Fourier-transform infrared spectroscopy (FTIR), and nuclear magnetic resonance (NMR), it was revealed that the ion coordination within the polymer–salt mixtures undergoes changes based on the composition of the starting neat polymer. Electrochemical evaluations identified the optimal composition for practical application as PVB11.5K-b-PDADMATFSI33K-b-PVB11.5K, showing an ionic conductivity at 70 °C of 4.2 × 10−5 S cm−1. This polymer electrolyte formulation was investigated for sodium in Na|Na symmetrical cells, showing an overpotential of 200 mV at 70 °C at 0.1 mA cm−2. When applied in a sodium–air battery, the polymer electrolyte membrane achieved a discharge capacity of 1.59 mAh cm−2 at 50 °C., This project received funding from the European Union’s Horizon 2020 research and innovation program under the Marie Skłodowska-Curie grant agreement No. 860403. The authors acknowledge the Australian Research Council (ARC) for funding through Discovery Programme DP160101178 and the ARC Industry Transformation Training Centre for Future Energy Technologies (storEnergy) for funding under grant agreement No. IC180100049.
Addi. Archivo Digital para la Docencia y la Investigación
Publication Artículo científico (JournalArticle)

Bio-based Polyhydroxyanthraquinones as High- Voltage Organic Electrode Materials for Batteries

  • Lap, Tijs Tobías
  • Goujon, Nicolas
  • Mantione, Daniele
  • Ruipérez Cillán, Fernando
  • Mecerreyes Molero, David
Unformatted postprint, Organic materials have gained much attention as sustainable electrode materials for batteries. Especially bio-based organic electrode materials (OEMs) are very interesting due to their geographical independency and low environmental impact. However, bio-based OEMs for highvotage batteries remain scarce. Therefore, in this work, a family of bio-based polyhydroxyanthraquinones (PHAQs) - namely 1,2,3,4,5,6,7,8-octahydroxyanthraquinone (OHAQ), 1,2,3,5,6,7-hexahydroxyanthraquinone (HHAQ) and 2,3,6,7-tetrahydroxyanthraquinone (THAQ) - and their redox polymers were synthesized. These PHAQs were synthesized from plantbased precursors and exhibit both a high-potential polyphenolic redox couple (3.5-4.0V vs. Li/Li+) and an anthraquinone redox moiety (2.2-2.8V vs. Li/Li+), while also showing initial charging capacities of up to 381 mAh g-1. To counteract the rapid fading caused by dissolution into the electrolyte, a facile polymerization method was established to synthesize PHAQ polymers. For this, the polymerization of HHAQ served as model reaction where formaldehyde, glyoxal and glutaraldehyde were tested as linkers. The resulting polymers were investigated as cathode materials in lithium metal batteries. PHAQ polymer composites synthesized using formaldehyde as linker and 10 wt.% multi-walled carbon nanotubes (MWCNTs), namely poly(THAQformaldehyde)-10 wt.% MWCNTs and poly(HHAQ-formaldehyde)-10 wt.% MWCNTs, exhibited the best cycling performance in the lithium metal cells, displaying a high-voltage discharge starting at 4.0V (vs. Li/Li+) and retaining 81.6 and 77.3 mAh g-1, respectively after 100 cycles., The authors want to thank the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No. 860403 and No. 101028682, as well as the European Union’s NextGenerationEU/PRTR programme. D.M. thanks Ayuda RYC2021-031668-I financiada por MCIN/AEI/10.13039/501100011033 y por la Unión Europea NextGenerationEU/PRTR.
Addi. Archivo Digital para la Docencia y la Investigación
Publication Artículo científico (JournalArticle)

Organic batteries based on just redox polymers

  • Goujon, Nicolas
  • Casado Pérez, Nerea
  • Patil, Nagaraj
  • Marcilla, Rebeca
  • Mecerreyes Molero, David
[EN]Redox-active polymers have gained interest as environmentally friendly alternative to inorganic materials in applications such as electrodes in lithium-ion batteries. All-polymer batteries were first disregarded with respect to other technologies due to their lower energy densities. However, the inherent benefits of redox polymers such as processability, flexibility, recyclability, high-rate performance and the perspective to prepare batteries from renewable resources has re-ignited interest in recent years. This review article aims to provide a comprehensive overview on the state of the art of batteries in which the active material is a redox polymer; including "static" all-polymer batteries and polymer-air batteries but also "flowing" systems such as polymer based redox-flow batteries (pRFB). First, a succinct overview of the recent developments of redox polymers will be given, summarizing the historic trends and developments. Second, an exhaustive discussion of the various battery prototypes will be provided, considering all steps in the development of organic batteries just based in redox polymers. Finally, future perspectives on all-polymer batteries will be discussed, summarizing the major challenges that are still to be overcome to unlock their commercial implementation., Authors thank POLYSTORAGE ETN project, this project has received funding from the European Union's Horizon 2020 research and innovation programme under the Marie Skodowska-Curie grant agreement No 860403. RM and NP thank the Spanish MCI through the SUSBAT project (Ref. RTI2018-101049-B-I0 0) and Juan de la Cierva fellowship [FJC2018-037781-I] (MCI-AEI/FEDER, UE) . NC would like to thank the University of the Basque Country forfunding through a specialization of research staff fellowship (ES-PDOC 19/99) . NG acknowledges the funding from the European Union's Horizon 2020 framework programme under the Marie Skodowska-Curie Agreement No. 101028682.
Addi. Archivo Digital para la Docencia y la Investigación
Publication Artículo científico (JournalArticle)

Bio-based ether solvent and ionic liquid electrolyte for sustainable sodium–air batteries

  • Stigliano, Pierre L.
  • Ortiz Vitoriano, Nagore
  • Medinilla, Lidia
  • Bara, Jason E.
  • López del Amo, Juan Miguel
  • Lezama Diago, Luis María
  • Forsyth, Maria
  • Mecerreyes Molero, David
  • Pozo Gonzalo, Cristina
Unformatted postprint, Sodium-air batteries (SABs) are receiving much attention in the last years due to their high theoretical high energy density (up to 1105 Wh kg-1). However, most of the studies on this technology are still based on organic solvents, in particular diglyme, a chemical considered highly flammable and toxic for the unborn child. Thus, the potential of the greener and low-toxic solvent 1,2,3 trimethoxypropane (TMP) as an alternative electrolyte to diglyme for SABs has been investigated for the first time in this publication. Through this work, it was found the reactivity of tertiary carbon present in TMP towards bare sodium metal. The addition of N-butyl-N-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide ([C4mpyr][TFSI]) as co-solvent proved to be effective to limit the reactivity. Moreover, a Na-β-alumina disk was employed as anode protection, to separate TMP-based electrolyte and sodium metal. The new cell design resulted in improved cell performance: discharge capacities of up to 1.92 and 2.31 mAh cm-2, for 16.6 mol% NaTFSI in TMP and 16.6 mol% NaTFSI in TMP/[C4mpyr][TFSI], respectively. By means of SEM, Raman and 23NMR techniques NaO2 cubes as the major discharge product for both electrolyte compositions were identified. Moreover, it was observed that the hybrid electrolyte hindered the formation of side-products during discharge (ratio NaO2 to side-products in the hybrid electrolyte is 2.4 in comparison with the TMP based electrolyte 0.8) and a different charge mechanism for the dissolution of NaO2 cubes for each electrolyte was observed. The findings of this work show the high potential of TMP as a base solvent for SABs, and the importance of careful electrolyte composition design, in order to step towards greener and less toxic batteries., This project has received funding from the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No 860403. N. Ortiz-Vitoriano acknowledges the R&D&I project PID2020-117626RA-I00 funded by MCIN/AEI/10.13039/501100011033 and Ramon y Cajal grant (RYC-2020-030104-I) funded by MCIN/AEI/10.13039/501100011033 and by FSE invest in your future.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Poly(vinyl benzoate)-b-poly(diallyldimethyl ammonium TFSI)-b-poly(vinyl benzoate) triblock copolymer electrolytes for sodium batteries

  • Stigliano, Pierre L.
  • Gallastegui, Antonela
  • Villacis Segovia, Carlos
  • Amores, Marco
  • Kumar, Ajit
  • O'Dell, Luke A.
  • Fang, Jian
  • Mecerreyes, David
  • Pozo Gonzalo, Cristina
  • Forsyth, Maria
6 figures.-- Supplementary information available., Block copolymers (BCPs) as solid electrolytes for batteries are usually designed to have an ion-solvating block for ion conduction and an ionophobic block for providing mechanical strength. Here, we show a novel solid polymer electrolyte (SPE) for sodium batteries based on a poly(vinyl benzoate)-b-poly(diallyldimethyl ammonium bis(trifluoromethanesulfonyl)imide) PVBx-b-PDADMATFSIy-b-PVBx ABA triblock copolymer. The SPE triblock copolymer comprises a polymerized ionic liquid (PIL) ion-solvating block combined with NaFSI salt as an internal block and an ionophilic PVB as an external block. Four distinct compositions with varying chain lengths of the blocks were synthesized by reversible addition−fragmentation chain-transfer (RAFT) polymerization. The neat copolymers were subsequently mixed with NaFSI in a 2:1 mol ratio of Na to ionic monomer units. Through comprehensive analysis using differential scanning calorimetry (DSC), Fourier-transform infrared spectroscopy (FTIR), and nuclear magnetic resonance (NMR), it was revealed that the ion coordination within the polymer–salt mixtures undergoes changes based on the composition of the starting neat polymer. Electrochemical evaluations identified the optimal composition for practical application as PVB11.5K-b-PDADMATFSI33K-b-PVB11.5K, showing an ionic conductivity at 70 °C of 4.2 × 10−5 S cm−1. This polymer electrolyte formulation was investigated for sodium in Na|Na symmetrical cells, showing an overpotential of 200 mV at 70 °C at 0.1 mA cm−2. When applied in a sodium–air battery, the polymer electrolyte membrane achieved a discharge capacity of 1.59 mAh cm−2 at 50 °C., This project received funding from the European Union’s Horizon 2020 research and innovation program under the Marie Skłodowska-Curie grant agreement No. 860403. The authors acknowledge the Australian Research Council (ARC) for funding through Discovery Programme DP160101178 and the ARC Industry Transformation Training Centre for Future Energy Technologies (storEnergy) for funding under grant agreement No. IC180100049., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

Supplementary materials for Poly(vinyl benzoate)-b-poly(diallyldimethyl ammonium TFSI)-b-poly(vinyl benzoate) triblock copolymer electrolytes for sodium batteries [Dataset]

  • Stigliano, Pierre L.
  • Gallastegui, Antonela
  • Villacis Segovia, Carlos
  • Amores, Marco
  • Kumar, Ajit
  • O'Dell, Luke A.
  • Fang, Jian
  • Mecerreyes, David
  • Pozo Gonzalo, Cristina
  • Forsyth, Maria
Experimental Section: Materials: Sodium bis(fluorosulfonyl)imide (NaFSI) (Solvionic, 99.99% purity was dried at 50 °C on under vacuum overnight and stored in Ar filled glovebox. The polymer electrolyte membranes were prepared as shown in Figure 3, NaFSI and the block copolymer were dissolved in a solvent mixture of tetrahydrofuran (THF) and acetonitrile (ACN). The solution was stirred at RT overnight and then cast on Teflon mold for solvent evaporation. The dry membranes were hot pressed and then dry at RT under vacuum, before being stored in Ar filled glovebox. Synthesis of PVB-PDADMTFSI-PVB block copolymers: The initial step of the synthesis involved synthesizing the double-functionalized chain transfer agent (CTA), known as X-DiEST-X. Diethyl meso-2,5-dibromoadipate (10 g; 27.7 mmol) was dissolved in 250 mL of 96% ethanol (EtOH) at room temperature in a 500 mL round bottom flask. Subsequently, potassium ethyl xanthogenate was added to the solution and stirred for 90 minutes. The reaction took place at room temperature for 4 hours. Upon completion, the resulting potassium bromide salt was filtered, and ethanol was removed under vacuum. The product was then dissolved in dichloromethane (DCM) and washed three times with distilled water. After evaporating the DCM, the product was dried under vacuum for 24 hours. The second step involved synthesizing the MacroCTA, denoted as X-PAm-DiEst-PAm-X, to achieve water solubility, a crucial property for the polymerization of PDADMACl. X-DiEst-X (4 g), acrylamide (12.8 g), and radical initiator AIBA (0.098 g) were dissolved in 8 mL of water and 35 mL of ethanol in a 50 mL Schlenk flask. The solution was then deoxygenated using nitrogen for 30 minutes. The reaction proceeded for one hour until a white precipitate formed. The precipitate was subsequently extracted and dried under vacuum at 40 °C overnight. Finally, the product was characterized using 1H-NMR and MALDI-TOF techniques (Figures S1 and S2). The polymerization process of the PDAMDATFSI block consisted of two stages. The first stage involved synthesizing poly-DADMACl: X-PAm-DiEst-PAm-X (2 g), AIBA (0.088 g), and PDADMACl (15.6 mL, 65 wt% aqueous solution) in a 50 mL Schlenk tube. The mixture was stirred and degassed with nitrogen for 30 minutes. The reactor was then placed in a preheated oil bath set at 60 °C. The final polymer was precipitated using a 1:1 mixture of ethanol and acetone, followed by filtration and vacuum drying at 40 °C. The product was analyzed using 1H-NMR in D2O (Figure S3). Once the PDADMACl polymer was obtained, an anion exchange was conducted to yield PDADMATFSI. PDADMACl was dissolved in distilled water and slowly added to a solution containing LiTFSI and distilled water under magnetic stirring. The resulting precipitate was then separated from the solvent, dried under vacuum at 40 °C overnight, and subsequently characterized using GPC-SEC (Figure S4). Two chain lengths of PDADMATFSI were investigated in this work: 33K and 17.5K, as shown in Table 1 To obtain the final product, PVB-b-PDADMATFSI-b-PVB triblock copolymers, PDADMATFSI and vinyl benzoate were dissolved in dimethylformamide (DMF) with AIBN as the initiator. The solution was deoxygenated with nitrogen for 30 minutes and then immersed in a preheated oil bath at 65 °C. After 24 hours of reaction, the final polymer was precipitated in cold ethanol, dried under vacuum at 40 °C for 24 hours, and the structure was characterized through 1H-NMR (Figure S5-8). MALDI-TOF: For MALDI-TOF measurements a Bruker Autoflex Speed system (Bruker, Germany) integrated with a Smartbeam-II laser (Nd:YAG, 355nm, 2 kHz) was used, with laser power adjusted during the measurements. The spectrum was acquired in linear mode with an average of 5000 shots. Samples were mixed in MeOH at a concentration of 10 mg/mL. The matrix used was 2,5-DHB, dissolved in MeOH at a concentration of 20 mg/mL. NaTFA was the cation donor (10 mg/mL dissolved in MeOH). A matrix/polymer/salt solution with 10:5:1 ratio was used and 0.5 μL were hand-spotted on the ground steel target plate. Gas Permeation Chromatography (GPC): For GPC a 1200 Infinity gel permeation chromatograph (GPC, Agilent Technologies) integrated with IR detector, a PLgel 5 mm MIXED-D column and a PLgel guard column (Agilent Technologies) was used. As eluent a 0,1 M LiTFSI/DMF solution was used and flow rate was set at 1.0 mL min-1 at 50 oC. PMMA standards (Agilent Technologies, Mp = 0.55 - 1568 x103) were used to perform calibration. Differential Scanning Calorimetry (DSC): Thermal properties of the neat block copolymers and polymer electrolyte membranes were measured by Netzsch DSC (214Polyma). All samples were characterized in the range of -100 and 150 oC, with a heating rate of 40K/min. The second heating is reported. Fourier Transform Infrared Spectroscopy (FTIR): The samples were measured by a Perkin Elmer instrument using a single diamond attenuated reflection unit. The spectra were measured in the region from 4000 to 650 cm-1. Transmission Electron Microscopy (TEM): Block copolymer films were placed into freshly prepared Procure 812 resin (ProSciTech Kirwan, QLD, C045) for 2 hours under vacuum infiltration at RT. The samples were then removed and put in resin mold (Procure 812 resin) before curing for 3 days at 580C. The resin block was sectioned using a Leica UC7 ultramicrotome to obtain silver interference (~50nm) sections and collected onto EMSFCFTH 400 mesh copper grids (ProSciTech Kirwan, QLD). Samples were imaged using a Tecnai 12 Transmission Electron Microscope (FEI, Eindhoven, The Netherlands), operating voltage of 120 kV. At all times low dose procedures were followed, using an electron dose of less than 5 electrons/Å2 for all imaging. Images were recorded using a FEI Eagle 4k x 4k CCD camera at a range of magnifications using AnalySIS v3.2 camera control software (Olympus). Solid State Magic Angle Spin Nuclear Magnetic Resonance Spectroscopy (MAS-NMR): For NMR spectroscopy, a Bruker Avance III 500 MHz ultra shield wide bore spectrometer was used. Zirconia MAS NMR rotors (diameter: 1.3 mm) were filled with samples inside Ar filled glovebox. Spectra were analysed using TopSpin software. Full-width half-maximum (fwhm) values were calculated by fitting the peaks with Gaussian/Lorentzian function. Ionic Conductivity: Ionic conductivity was measured using MTZ-35 in the frequency range of 1 Hz to 10 MHz (amplitude of 0.01 V) in the temperature range of 30 and 90 °C. The polymer electrolyte membranes were cut into 12 mm diameter round discs and andwiched between two stainless steel electrodes inside of a coin cell. The coin cell was then put in a custom-built barrel cell. All the spectra were fitted by MTlab software. Electrochemical Characterization: TNa + at 70 oC was measured with the Bruce−Vincent method, the equation used for calculation is: TNa+ = 𝐼s(Δ𝑉 − 𝐼0𝑅i0)/𝐼0(Δ𝑉 − 𝐼s𝑅is) Where ΔV = applied constant potential, I0 and Is = initial and steady-state currents, respectively, and Rio and Ris = initial and steady state interfacial resistance, respectively. Na|Na symmetric cell cycling was performed using a coin cell with the electrolyte membrane (thickness 300 μm, diameter 14 mm) sandwiched between 2 Na metal discs (diameter 10 mm). Cells were assembled inside an Ar filled glovebox. Na-metal stripping and plating were studied at different currents using a Biologic VMP3 potentiostat, data were processed with EC-Lab software. A homemade 2-electrode Swagelok-type cell was employed for Sodium-Air Battery (SAB) testing. The cell parts were dried at 60 °C overnight and then transferred to an Ar filled glovebox for assembling. The SAB cell was composed of a sodium metal disk (diameter = 12 mm, Sigma Aldrich), the polymer electrolyte membrane (diameter = 12.7 mm) and multi-doped carbon nanofibers air cathode (reported in literature). The surface of the air cathode was wetted with 50 uL of liquid electrolyte (NaTFSI:diglyme:C4mpyrTFSI in mol ratio 1:4:1) to improve contact between air cathode and polymer electrolyte membrane. Once assembled, the cells were taken outside of the Ar filled glovebox and pressurized under pure oxygen (99.99% purity). The cells were left to rest for 8 h at open circuit voltage and 50 oC. Subsequently, a current density of -75 μA cm-2 was applied, with a cut-off potential of 1.6 V.-- Under a Creative Commons license CC BY 4.0 Deed Attribution 4.0 International, Experimental Section, Figure S1: H-NMR (300 MHz) di funcional CTA X-PAm-DiEst-PAm-X in D2O; Figure S2: MALDI-TOF analysis of X-Pam-DiEst-Pam-X (X-AdA-X); Figure S3: H NMR (300 MHz) of MacroCTA in D2O; Figure S4 H-NMR of PVB11.5K–b–PDADMATFSI33K–b–PVB11.5K; Figure S5 H-NMR of PVB11.5K–b–PDADMATFSI17.5K–b–PVB11.5K; Figure S6 H-NMR of PVB22.5K–b–PDADMATFSI33K–b–PVB22.5K; Figure S7 H-NMR of PVB22.5K–b–PDADMATFSI17.5K–b–PVB22.5K; Table S1: FTIR absorption band positions and assignment for neat PVB-PDADMAT-PVB BCPs; Figure S8: TEM images of BCP BCP-1233 and BCP-2218; Table S2: Sample name and characteristics of the membrane with 2:1 Na:PDADMATFSI mol ratio for all four compositions of neat polymer; Figure S9: TEM images of BCP BCP-1233-Na and BCP-2218-Na; Figure S10: Ratio between integrals of the two coordination peaks observed in 23Na NMR; Figure S11: FTIR spectra of neat BCP and BCP-NaFSI mixtures with a 2:1 Na:PDADMA mol ratio; Figure S12: Galvanostatic cycling of sodium symmetrical cells using BCP-1233-Na at 70 °C; Figure S13: Photo of the membrane after galvanostatic cycling in Na| Na cells showing the formation of large dendrites; Figure S14: SEM images of the surface of BCP-1233-Na and BCP-2218-Na, and EDS layered image zoomed on one of the structures found on the surface of BCP-2218-Na; Figure S15: SEM images of the cross-section of BCP-1233(2); Figure S16: Cell configuration of the home modified Swagelok-type Na-O2 cell used., This project received funding from the European Union’s Horizon 2020 research and innovation program under the Marie Skłodowska-Curie grant agreement No. 860403. The authors acknowledge the Australian Research Council (ARC) for funding through Discovery Programme DP160101178 and the ARC Industry Transformation Training Centre for Future Energy Technologies (storEnergy) for funding under grant agreement No. IC180100049., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Otros (Other)

2024 roadmap for sustainable batteries

  • Titirici, Magda
  • Johansson, Patrik
  • Crespo Ribadeneyra, Maria
  • Au, Heather
  • Innocenti, Alessandro
  • Passerini, Stefano
  • Petavratzi, Evi
  • Lusty, Paul
  • Tidblad, Annika Ahlberg
  • Naylor, Andrew J.
  • Younesi, Reza
  • Chart, Yvonne A.
  • Aspinall, Jack
  • Pasta, Mauro
  • Orive, Joseba
  • Babulal, Lakshmipriya Musuvadhi
  • Reynaud, Marine
  • Latham, Kenneth G.
  • Hosaka, Tomooki
  • Komaba, Shinichi
  • Bitenc, Jan
  • Ponrouch, Alexandre
  • Zhang, Heng
  • Armand, Michel
  • Kerr, Robert
  • Howlett, Patrick C.
  • Forsyth, Maria
  • Brown, John
  • Grimaud, Alexis
  • Vilkman, Marja
  • Dermenci, Kamil Burak
  • Mousavihashemi, Seyedabolfazl
  • Berecibar, Maitane
  • Marshall, Jean E.
  • McElroy, Con Robert
  • Kendrick, Emma
  • Safdar, Tayeba
  • Huang, Chun
  • Zanotto, Franco M.
  • Troncoso, Javier F.
  • Domínguez, Diana Zapata
  • Alabdali, Mohammed
  • Vijay, Utkarsh
  • Franco, Alejandro A.
  • Pazhaniswamy, Sivaraj
  • Grant, Patrick S.
  • López Guzman, Stiven
  • Fehse, Marcus
  • Galceran, Montserrat
  • Antuñano, Néstor
Modern batteries are highly complex devices. The cells contain many components—which in turn all have many variations, both in terms of chemistry and physical properties. A few examples: the active materials making the electrodes are coated on current collectors using solvents, binders and additives; the multicomponent electrolyte, contains salts, solvents, and additives; the electrolyte can also be a solid ceramic, polymer or a glass material; batteries also contain a separator, which can be made of glass fibres, polymeric, ceramic, composite, etc. Moving up in scale all these components are assembled in cells of different formats and geometries, coin cells and Swagelok cells for funamental testing and understanding, and pouch, prismatic and cylindrical cells for application. Given this complexity dictated by so many components and variations, there is no wonder that addressing the crucial issue of true sustainability is an extremely challenging task. How can we make sure that each component is sustainable? How can the performance can be delivered using more sustainable battery components? What actions do we need to take to address battery sustainability properly? How do we actually qualify and quantify the sustainability in the best way possible? And perhaps most importantly; how can we all work—academia and battery industry together—to enable the latter to manufacture more sustainable batteries for a truly cleaner future? This Roadmap assembles views from experts from academia, industry, research institutes, and other organisations on how we could and should achieve a more sustainable battery future. The palette has many colours: it discusses the very definition of a sustainable battery, the need for diversification beyond lithium-ion batteries (LIBs), the importance of sustainability assessments, the threat of scarcity of raw materials and the possible impact on future manufacturing of LIBs, the possibility of more sustainable cells by electrode and electrolyte chemistries as well as manufacturing, the important role of new battery chemistries, the crucial role of AI and automation in the discovery of the truly sustainable batteries of the future and the importance of developimg a circular battery economy., H A would like to thank the Faraday Institution's LiSTAR project (EP/S003053/1, Grant FIRG014) for funding. The authors acknowledge the EU's Horizon 2020 Research and Innovation Programme under Marie Skłodowska-Curie Grant Agreement 860403 'POLYSTORAGE' for the funding, as well as the Helmholtz Association basic funding. The work in this paper was funded by the UKRI Interdisciplinary Circular Economy Centre for Technology Metals (Met4Tech) (EP/V011855/1) project. This paper has been produced as an activity within Batteries Sweden (BASE), a Centre of Excellence co-funded by Sweden's Innovation Agency (Vinnova), the industry and the academy. Y A C, J A, and M P acknowledge support by the Faraday Institution [Grant Numbers FIRG056 and FIRG058]. The authors acknowledge funding from MCIN/AEI/10.13039/501100011033 through the project ION-SELF ref. PID2019-106519RB-I00, as well as the Spanish Ministerio de Industria, Comercio y Turismo and the European Union—Next Generation EU for their financial support through the project VEC-020100-2022-127/PP27. K G L acknowledges the European Research Council under the Horizon 2020 framework for the Marie Curie Research Fellowship (888124) through the project HYBRIDFLEX. The authors thank the JSPS KAKENHI (Grant Nos. JP20H02849, JP21K20561, and JP22K14772),the MEXT Program: Data Creation and Utilization Type Materials Research and Development Project (JPMXP1122712807), and JST-CREST (Grant No. JPMJCR21O6) for financial support. Funding from the European Research Council is acknowledged: ERC-2022-CoG, MULTIMETALBAT, Grant agreement No. 101089281. A P is grateful to the Spanish Agencia Estatal de Investigación Severo Ochoa Programme for Centres of Excellence in R&D (CEX2023-001263-S). J B would like to acknowledge financial support of Slovenian Research Agency through research programme P2-0423 and research Projects J2-4462 and N2-0279. The authors acknowledge the financially supported by the National Natural Science Foundation of China (Nos. 52203223 and 22279037) and the Fundamental Research Funds for Central Universities, HUST (2020kfyXJJS095). J B as a part of the DESTINY PhD programme acknowledges funding from the European Union's Horizon 2020 research and innovation programme under the Marie Skłodowská–Curie Grant Agreement No: 945357. The authors are grateful to the UK Faraday Institution for financial support through grant SOLBAT—next generation solid state batteries [FIRG066]. This work has received funding from the European Union's Horizon 2020 research and innovation programme under Grant Agreements 957225 (BAT4EVER) and 957202 (HIDDEN). The authors want to thank the Battery 2030+ initiative (Grant Agreement No. 957213) for enabling the collaboration. The authors would like to thank the Faraday Institution ReLiB project (Grant Codes FIRG005, FIRG027 and FIRG057) and UKRI Faraday Battery Challenge project 'Reclamation and Re-manufacture of lithium ion batteries,' Reference Number 104425 and The Faraday Institution. Manufacturing of Advanced Electrodes with Green Solvents—MAEGS, FIRG040. This work was carried out with the support of the Faraday Institution (FIRG060, FIRG066), the Faraday Institution Industry Fellowship (FIIF015), the Faraday Institution Training Grant (FITG034), the ERC Starting Grant (converted to UKRI funding EP/Y009908/1), and the Imperial College London UKRI Impact Acceleration Account (EP/X52556X/1). A A F and D Z D acknowledge the European Union's Horizon 2020 research and innovation program for the funding support through the European Research Council (Grant Agreement 772873, 'ARTISTIC' project). F M Z and A A F acknowledge the European Union's Horizon Europe research and innovation programme under Grant Agreement No. 101069686 (PULSELiON). M A, U V, and A A F as a part of the DESTINY PhD programme acknowledge funding from the European Union's Horizon2020 research and innovation programme under the Marie Skłodowska–Curie Actions COFUND—Grant Agreement No: 945357. M A and A A F also acknowledge the support of Umicore as part of DESTINY. A A F acknowledges the Institut Universitaire de France for their support. Some of the icons used in figure 23 are originated (free to use) from freepik.com. The European Union's Horizon Europe research and innovation programme is acknowledged for funding the project HighSpin (GA No. 101069508) and the associated PhD of S L., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Gel polymer electrolytes based on sulfonamide functional polymer nanoparticles for sodium metal batteries

  • Stigliano, Pierre L.
  • Gallastegui, Antonela
  • Smith, Thomas H.
  • O'Dell, Luke A.
  • Mecerreyes, David
  • Pozo Gonzalo, Cristina
  • Forsyth, Maria
8 figures., In this work, we investigate the development of polymer electrolytes for sodium batteries based on sulfonamide functional polymer nanoparticles (NaNPs). The synthesis of the polymer NaNPs is carried out by emulsion copolymerization of methyl methacrylate and sodium sulfonamide methacrylate in the presence of a crosslinker, resulting in particle sizes of 50 nm, as shown by electron microscopy. Then, gel polymer electrolytes are prepared by mixing polymer NPs and different organic plasticizers including carbonates, glymes, sulfolanes and ionic liquids. The chemical nature of the plasticizer resulted in different effects on the sodium coordination shell, which in turn impacted the properties of each membrane as investigated by FTIR. The transport properties were investigated by EIS and solid-state NMR. Among the organic gel polymer electrolytes (GPEs), the system comprising NaNPs and sulfolanes achieved the best ionic conductivity (1.1 × 10−4 S cm−1 at 50 °C) and sodium single-ion properties while for the ionogels, the best ionic conductivity was obtained by NaNPs mixed with pyrrolidinium-FSI IL (4.7 × 10−4 S cm−1 at 50 °C). From sodium metal symmetrical cell cycling, the use of ILs as plasticizers proved to be more beneficial for SEI formation and its evolution during cell cycling compared to the systems based on NPs and organic solvents. However, NPs + PC led to lower cell overvoltage than NPs + ILs (<0.4 V vs. >0.5 V). This study shows the potential of using Na-sulfonamide functional polymer nanoparticles to immobilize different plasticizers and thereby obtain soft-solid electrolytes for Na metal batteries., This project has received funding from the European Union's Horizon 2020 research and innovation program under the Marie Skłodowska-Curie grant agreement no. 860403. The authors acknowledge the Australian Research Council (ARC) for funding through Discovery Programme DP160101178 and the ARC Industry Transformation Training Centre for Future Energy Technologies (storEnergy) for funding under grant agreement no. IC180100049., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

Supplementary information to Gel polymer electrolytes based on sulfonamide functional polymer nanoparticles for sodium metal batteries [Dataset]

  • Stigliano, Pierre L.
  • Gallastegui, Antonela
  • Smith, Thomas H.
  • O'Dell, Luke A.
  • Mecerreyes, David
  • Pozo Gonzalo, Cristina
  • Forsyth, Maria
Under a Creative Commons BY 3.0 license., Table S1 Composition, surfactant wt%, size, PdI, conversion rate, and Na content of neat NaNPs.-- Figure S1 IR-absorbance spectra for the Na-functionalized polymer nanoparticles showing the whole spectrum (a), the TFSI environment (b), and the C=O environment (c).-- The FTIR spectra in the 700-800 cm-1 spectral region (Figure S1b) were analysed focusing on the solvation of the TFSI in the nanoparticles. Three bands were observed at 740, 749, and 762 cm-1. The 740 cm-1 peak corresponds to vibrations stemming from expansions and contractions of pseudo-free TFSI anions. This observation aligns with FTIR investigations of ionic liquids containing TFSI anions, such as C4mpyrTFSI, where a similar main band at 742 cm-1 is detected alongside a secondary band at 762 cm-1, just as observed in the nanoparticles investigated in this work. It was previously reported in literature, that when systems containing TFSI are mixed with Li or Na salts, there is an appearance of a main band at 749 cm-1 that gets more significant the higher the concentration of Li/Na ions in the system, thus this peak was associated with the coordinated TFSI. Interestingly, despite expectations of complete association between TFSI anions and Na+ in neat NPs, the presence of both free and coordinated TFSI suggests a different interaction between Na+ and the [MTFSI]-, which will need more investigation in the future. Turning attention to the spectral region 1650-1780 cm-1 (Figure S1c), the prominent peak observed at 1729 cm-1 is attributed to the C=O stretching vibration. Given the strong coordinating nature of the C=O moiety with metal ions such as Na, in literature this peak has been analyzed to investigate the coordination upon the addition of Li or Na salts in MMA-based electrolytes. It was observed that the coordination of C=O with Li/Na resulted in the appearance of a shoulder at lower wavelengths, which would grow more intense with higher content of metal ions. In our system, the C=O peak stems from both MMA and NaMTFSI. As it is possible to see, the shoulder indicating coordination with Na ions is present at 1714 cm-1. The coordination of C=O with Na+ would further explain the earlier observations about the presence in the system of free TFSI anion in the spectral region 700-800 cm-1.--Table S2 Assignment of bands related to NaMTFSI and MMA in the neat NaNPs.-- Table S3 Ionic conductivity values at 50 oC and calculated activation energy values for the gel polymer electrolytes based on sodium-functionalized polymer nanoparticles.-- Figure S2 FTIR spectra of neat plasticizers.-- Figure S3 EIS of initial 24h, symmetrical cycling at 0.02 mA cm-2, and EIS spectra before and after cycling at 50 oC of NPs+C4mpyrTFSI (a,b,c), NPs+C3mpyrFSI (d,e,f), and NPs+P111i4FSI (g,h,i).-- Figure S4 EIS spectra and polarization before and after symmetrical cycling at 0.02 mAh cm-2 and 50 oC for all samples NPs+plasticizer.-- Figure S5 EIS of initial 24h, symmetrical cycling at 0.02 and 0.05 mA cm-2, and EIS spectra before and after cycling at 50 oC of NPs+SL+NaFSI (a,b,c), NPs+PS+NaFSI (d,e,f), This project has received funding from the European Union's Horizon 2020 research and innovation program under the Marie Skłodowska-Curie grant agreement no. 860403. The authors acknowledge the Australian Research Council (ARC) for funding through Discovery Programme DP160101178 and the ARC Industry Transformation Training Centre for Future Energy Technologies (storEnergy) for funding under grant agreement no. IC180100049., Peer reviewed