Skip to main content

COMBUSTION EFICIENTE Y LIMPIA EN MOTORES DE ENCENDIDO POR COMPRESION UTILIZANDO EL CONCEPTO DUAL-FUEL

BES-2012-059721

•
Funding agency name Ministerio de Ciencia e Innovación
Funding agency acronym MICINN
Program Programa Nacional de Formación de Personal Investigador
Subprogram Subprograma de Ayudas de Formación de Personal Investigador
Call Contratos Predoctorales
Call year 2012
State Plan 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Management unit Secretaría de Estado de Educación, Formación Profesional y Universidades
Beneficiary centre UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Application of optical diagnostics to the quantification of soot in n-alkane flames under diesel conditions

  • Pastor, José V.|||0000-0003-4113-4681
  • García-Oliver, José M|||0000-0002-2676-9681
  • Micó, Carlos|||0000-0001-5787-6212
  • Möller, Sebastian
  • García Martínez, Antonio
The present work pursues a twofold objective. On the one hand, the effect of fuel properties on soot formation has been analysed, under different engine operating conditions. On the other hand, sensitivity and performance of the three optical techniques has been evaluated, identifying their main advantages and drawbacks in the framework of the current study. LEM has been considered as the reference technique, as the measurement principle can be implemented without important limitations associated to the other two. Results highlight that larger molecules produce more soot than the smaller ones, with both reactivity and soot formation changing with the proportion of the heavier fraction. Despite describing similar trends, LEM and 2C do not provide the same KL values, with the pyrometry reaching some sort of saturation when increasing flame soot. A detailed analysis confirms that 2-Colar measurements are strongly biased by soot and temperature distribution inside the flame. Nevertheless, it could still be a good option for low sooting conditions. On the other hand, an attempt to calibrate LII signal by means of LEM measurements has been reported. This approach should make it possible to obtain additional information on the soot spatial distribution. However, inconsistencies have been identified which stem from the inherent limitations of LII technique in highly sooting conditions. (c) 2015 The Combustion Institute. Published by Elsevier Inc. All rights reserved., Authors wold like to acknowledge that part of this work has been funded by the Spanish Ministry of Science and Technology through project TRA2011-26359 and grant BES-2012-059721. Some other parts of this works were financially supported by "COMET K2 - Competence Centres for Excellent Technologies Programme" (project B03T02). In addition, the authors acknowledge that some equipment used in this work has been partially supported by FEDER project funds (FEDER-ICTS-2012-06)", framed in the operational program of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Application of UV Visible Light Absorption and Scattering technique to low absorption fuels under diesel-like conditions

  • Pastor, José V.|||0000-0003-4113-4681
  • García-Oliver, José M|||0000-0002-2676-9681
  • López, J. Javier|||0000-0002-9486-2511
  • Micó, Carlos|||0000-0001-5787-6212
Light Absorption and Scattering technique (LAS) has been applied for the measurement of fuel vapour distribution in diesel-type sprays. This technique is usually limited to fuels with relatively high absorptivity, which are sometimes not commonly used as surrogate fuels. In the present paper, a comparison of fuels with very different absorptive properties has been made to determine the range of application of the methodology. A calibration procedure has been applied to n-decane (DEC), a binary blend of n-decane and n-hexadecane (50DEC) and three blends of n-heptane with a highly-absorpting fuel (HEPB1, HEPB2 and HEPB3). This methodology enables the in-situ quantification of absorption coefficients at high pressure and temperature by creating a uniform mixture inside the cylinder. Results have been later applied for the quantification of fuel vapour distribution in sprays for DEC, 50DEC and HEPB3. Results obtained with these range of fuels have enabled to establish the limit in terms of absorption coefficient needed to get consistent results with the technique., This work was partially funded by the Government of Spain through Project TRA2011-26359 and Grant BES-2012-059721. In addition, the authors acknowledge that some equipment used in this work has been partially supported by FEDER project funds (FEDER-ICTS-2012-06), framed in the operational program of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain.