Skip to main content

COMBUSTION EFICIENTE Y LIMPIA EN MOTORES DE ENCENDIDO POR COMPRESION UTILIZANDO EL CONCEPTO DUAL-FUEL

TRA2011-26359

•
Funding agency name Ministerio de Ciencia e Innovación
Funding agency acronym MICINN
Program Programa Nacional de Proyectos de Investigación Fundamental
Subprogram Subprograma de Proyectos de Investigación Fundamental no Orientada
Call Proyectos I+D
Call year 2011
State Plan 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Management unit Subdirección General de Proyectos de Investigación
Beneficiary centre UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

An experimental study of the effects of fuel properties on reactive spray evolution using Primary Reference Fuels

  • Pastor, José V.|||0000-0003-4113-4681
  • García-Oliver, José M|||0000-0002-2676-9681
  • López, J. Javier|||0000-0002-9486-2511
  • Vera-Tudela-Fajardo, Walter Martin
An experimental study on the ignition and combustion of diesel-type sprays using n-heptane, iso-octane and four intermediate blends is presented. The choice of components was done in order to represent the transition from conventional diesel fuel (n-heptane) to a gasoline-like one (iso-octane) in terms of ignition behavior. The experiments have been carried out in a high pressure high temperature vessel using specifications from the Engine Combustion Network (ECN). Parametric variations of oxygen concentration and air temperature have been performed for each fuel. In order to investigate the spray development, schlieren imaging for the quantification of spray penetration and ignition delay, OH/chemiluminescence imaging for the lift-off length, and broadband radiation imaging for the soot intensity and flame length have been applied. The results show the large effect of mixture reactivity on the ignition times and lift-off length values. Regarding the effect of the octane number of the blends on the ignition delay times, a linear effect has been found in the lower half of the blend range, while an exponential trend is evident in the top one. On the other hand, a scaling law for the stabilized flame length based upon momentum-controlled assumptions has shown that results are comparable to those obtained in the literature. Finally, the applicability of the results obtained on the performance and efficiency in real engines is discussed. (C) 2015 Elsevier Ltd. All rights reserved., Authors acknowledge that part of this work was performed in the frame of Project DUFUEL TRA2011-26359, funded by the Spanish Government. Also, authors would like to thank the Pontificia Universidad Catolica del Peru for financing the first year of studies of W. Vera-Tudela and making it possible for him to start his program of Ph.D. at the Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

An experimental analysis on the evolution of the transient tip penetration in reacting Diesel sprays

  • Desantes J.M.|||0000-0002-4124-9393
  • García-Oliver, José M|||0000-0002-2676-9681
  • Pastor, José V.
  • Briceño Sánchez, Francisco Javier
Schlieren imaging has helped deeply characterize the behavior of Diesel spray when injected into an oxygen-free ambient. However, when considering the transient penetration of the reacting spray after autoignition, i.e. the Diesel flame, few studies have been found in literature. Differences among optical setups as well as among experimental conditions have not allowed clear conclusions to be drawn on this issue. Furthermore, soot radiation may have a strong effect on the image quality, which cannot be neglected. The present paper reports an investigation on the transient evolution of Diesel flame based upon schlieren imaging. Experimental conditions have spanned values of injection pressure, ambient temperature and density for typical Diesel engine conditions. An optimized optical setup has been used, which makes it possible to obtain results without soot interference. Based on observations for a long injection event (4 ms Energizing Time), the analysis has resorted to extensive comparison of inert and reacting sprays parameters, which have made it possible to define different phases after autoignition. Shortly after autoignition, axial and radial expansion of the spray have been observed in terms of tip penetration and radial cone angle. After that, during a stabilization phase, the reacting spray penetrates at a similar rate as the inert one. Later, the reacting spray undergoes an acceleration period, where it penetrates at a faster rate than the inert one. Finally, the flame enters a quasi-steady penetration phase, where the ratio of reacting and inert penetration stabilizes at a nearly constant value. The duration of the reacting spray penetration stages shows modifications when varying engine parameters such as air temperature, air density, injection pressure, and nozzle diameter. However, the proportionality between reacting and inert penetration has been observed to depend mainly on temperature, in agreement with observed reductions in entrainment when shifting from inert to reacting conditions. (C) 2014 The Combustion Institute. Published by Elsevier Inc. All rights reserved., This work was partially funded by the Spanish Ministry of Science and Technology through the "EFFICIENT AND CLEAN COMBUSTION IN COMPRESSION IGNITION ENGINES USING THE DUAL-FUEL CONCEPT" Project (TRA2011-26359). Mr. Francisco J. Briceno wishes to acknowledge financial support through a PhD studies Grant (AP2008-02231) also sponsored by the Spanish Ministry of Education and Science. Last, but not least, authors would like to express their gratitude to Jose Enrique del Rey for his enthusiasm, proactiveness and help during data acquisition.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A spectroscopy study of gasoline partially premixed compression ignition spark assisted combustion

  • Pastor, José V.|||0000-0003-4113-4681
  • García-Oliver, José M|||0000-0002-2676-9681
  • Micó, Carlos|||0000-0001-5787-6212
  • García Martínez, Antonio
  • Durret, R.
Nowadays many research efforts are focused on the study and development of new combustion modes, mainly based on the use of locally lean air–fuel mixtures. This characteristic, combined with exhaust gas recirculation, provides low combustion temperatures that reduces pollutant formation and increases efficiency. However these combustion concepts have some drawbacks, related to combustion phasing control, which must be overcome. In this way, the use of a spark plug has shown to be a good solution to improve phasing control in combination with lean low temperature combustion. Its performance is well reported on bibliography, however phenomena involving the combustion process are not completely described. The aim of the present work is to develop a detailed description of the spark assisted compression ignition mode by means of application of UV–Visible spectrometry, in order to improve insight on the combustion process. Tests have been performed in an optical engine by means of broadband radiation imaging and emission spectrometry. The engine hardware is typical of a compression ignition passenger car application. Gasoline was used as the fuel due to its low reactivity. Combining broadband luminosity images with pressure-derived heat-release rate and UV–Visible spectra, it was possible to identify different stages of the combustion reaction. After the spark discharge, a first flame kernel appears and starts growing as a premixed flame front, characterized by a low and constant heat-release rate in combination with the presence of remarkable OH radical radiation. Heat release increases temperature and pressure inside the combustion chamber, which causes the auto-ignition of the rest of the unburned mixture. This second stage is characterized by a more pronounced rate of heat release and a faster propagation of the reactions through the combustion chamber. Moreover, the measured UV–Visible spectra show some differences in comparison with the other stages. The relative intensities in of spectra from different combustion radicals have also been related to the different combustion phases., The authors acknowledge that part of this work was performed in the frame of Project DUFUEL TRA2011-26359, funded by the Spanish Government. The authors also thank GM for technical assistance and its support in other parts of this work.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Application of optical diagnostics to the quantification of soot in n-alkane flames under diesel conditions

  • Pastor, José V.|||0000-0003-4113-4681
  • García-Oliver, José M|||0000-0002-2676-9681
  • Micó, Carlos|||0000-0001-5787-6212
  • Möller, Sebastian
  • García Martínez, Antonio
The present work pursues a twofold objective. On the one hand, the effect of fuel properties on soot formation has been analysed, under different engine operating conditions. On the other hand, sensitivity and performance of the three optical techniques has been evaluated, identifying their main advantages and drawbacks in the framework of the current study. LEM has been considered as the reference technique, as the measurement principle can be implemented without important limitations associated to the other two. Results highlight that larger molecules produce more soot than the smaller ones, with both reactivity and soot formation changing with the proportion of the heavier fraction. Despite describing similar trends, LEM and 2C do not provide the same KL values, with the pyrometry reaching some sort of saturation when increasing flame soot. A detailed analysis confirms that 2-Colar measurements are strongly biased by soot and temperature distribution inside the flame. Nevertheless, it could still be a good option for low sooting conditions. On the other hand, an attempt to calibrate LII signal by means of LEM measurements has been reported. This approach should make it possible to obtain additional information on the soot spatial distribution. However, inconsistencies have been identified which stem from the inherent limitations of LII technique in highly sooting conditions. (c) 2015 The Combustion Institute. Published by Elsevier Inc. All rights reserved., Authors wold like to acknowledge that part of this work has been funded by the Spanish Ministry of Science and Technology through project TRA2011-26359 and grant BES-2012-059721. Some other parts of this works were financially supported by "COMET K2 - Competence Centres for Excellent Technologies Programme" (project B03T02). In addition, the authors acknowledge that some equipment used in this work has been partially supported by FEDER project funds (FEDER-ICTS-2012-06)", framed in the operational program of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Application of UV Visible Light Absorption and Scattering technique to low absorption fuels under diesel-like conditions

  • Pastor, José V.|||0000-0003-4113-4681
  • García-Oliver, José M|||0000-0002-2676-9681
  • López, J. Javier|||0000-0002-9486-2511
  • Micó, Carlos|||0000-0001-5787-6212
Light Absorption and Scattering technique (LAS) has been applied for the measurement of fuel vapour distribution in diesel-type sprays. This technique is usually limited to fuels with relatively high absorptivity, which are sometimes not commonly used as surrogate fuels. In the present paper, a comparison of fuels with very different absorptive properties has been made to determine the range of application of the methodology. A calibration procedure has been applied to n-decane (DEC), a binary blend of n-decane and n-hexadecane (50DEC) and three blends of n-heptane with a highly-absorpting fuel (HEPB1, HEPB2 and HEPB3). This methodology enables the in-situ quantification of absorption coefficients at high pressure and temperature by creating a uniform mixture inside the cylinder. Results have been later applied for the quantification of fuel vapour distribution in sprays for DEC, 50DEC and HEPB3. Results obtained with these range of fuels have enabled to establish the limit in terms of absorption coefficient needed to get consistent results with the technique., This work was partially funded by the Government of Spain through Project TRA2011-26359 and Grant BES-2012-059721. In addition, the authors acknowledge that some equipment used in this work has been partially supported by FEDER project funds (FEDER-ICTS-2012-06), framed in the operational program of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain.