Skip to main content

REUTILIZACION DE RESIDUOS CERAMICOS Y DE DEMOLICION EN LA PREPARACION DE NUEVOS MATERIALES GEOPOLIMERICOS

BIA2011-26947

•
Funding agency name Ministerio de Ciencia e Innovación
Funding agency acronym MICINN
Program Programa Nacional de Proyectos de Investigación Fundamental
Subprogram Subprograma de Proyectos de Investigación Fundamental no Orientada
Call Proyectos I+D
Call year 2011
State Plan 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Management unit Subdirección General de Proyectos de Investigación
Beneficiary centre UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 15
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Effect of curing time on the microstructure and mechanical strength development of alkali activated binders based on vitreous calcium aluminosilicate (VCAS)

  • Mitsuuchi Tashima, Mauro|||0000-0003-0885-9293
  • Soriano Martinez, Lourdes|||0000-0002-5749-4609
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
The aim of this paper is to study the influence of curing time on the microstructure and mechanical strength development of alkali activated binders based on vitreous calcium aluminosilicate (VCAS). Mechanical strength of alkali activated mortars cured at 65 °C was assessed for different curing times (4¿168 h) using 10 molal NaOH solution as alkaline activator. Compressive strength values around 77 MPa after three days of curing at 65 °C were obtained. 1·68 MPa/h compressive strength gain rate was observed in the first 12 h, decreasing to 0·95 MPa/h for the period of 12¿72 h. The progress of geopolymeric reaction was monitored by means of TGA and, electrical conductivity and pH measurements in an aqueous suspension. Significant decrease in pH and electrical conductivity were observed in the 4¿72 h period, demonstrating the geopolymerization process. Furthermore, SEM images showed an important amount of (N, C)ASH gel and low porosity of the developed matrix., To the Ministerio de Ciencia e Innovacion (MICINN) of the Spanish Government (BIA2011-26947) and also to FEDER for funding and to Vitrominerals company for supplying VCAS samples.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Refluxed rice husk ash/NaOH suspension for preparing alkali activated binders

  • Bouzón, N.
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Soriano Martinez, Lourdes|||0000-0002-5749-4609
  • Mitsuuchi Tashima, Mauro|||0000-0003-0885-9293
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
Geopolymers simultaneously containing two waste materials have been developed: fluid catalytic cracking catalyst (FCC) as mineral admixture and rice husk ash (RHA) for preparing an alkaline activator. Alkaline activators were prepared by refluxing aqueous mixtures of ground or original RHA with NaOH. All mortars with alkaline activator containing RHA show compressive strength (cured at 65 °C for 1 day) in the range of 31 41 MPa, which is similar to control mortar prepared using an equivalent mixture of NaOH and water glass. Refluxing times between 30 and 240 min yielded good performance mortars. This new way of valorisation would imply economic and environmental benefits in geopolymer production., GEOCEDEM Project BIA 2011-26947 was financed by Spanish Government, Project 3018/2009 was financed by Generalitat Valenciana, Project AP/35235/11 was financed by AECID, COMBURES Project was financed by Centro de Cooperacion al Desarrollo de la Universitat Politecnica de Valencia ADSIDEO COOPERACIO and OMYA Clariana S.A. and Maicerias Espanolas DACSA S.A. supplied FCC and RHA samples respectively.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Alkali activated materials based on fluid catalytic cracking catalyst residue (FCC): Influence ofSiO2/Na2O and H2O/FCC ratio on mechanical strength and microstructure

  • Mitsuuchi Tashima, Mauro|||0000-0003-0885-9293
  • Soriano Martinez, Lourdes|||0000-0002-5749-4609
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Akasaki, Jorge Luis
  • Melges, J.L.P.
Reuse of industrial and agricultural wastes as supplementary cementitious materials (SCMs) in concrete and mortar productions contribute to sustainable development. In this context, fluid catalytic cracking catalyst residue (spent FCC), a byproduct from the petroleum industry and petrol refineries, have been studied as SCM in blended Portland cement in the last years. Nevertheless, another environmental friendly alternative has been conducted in order to produce alternative binders with low CO2 emissions. The use of aluminosilicate materials in the production of alkali-activated materials (AAMs) is an on going research topic which can present low CO2 emissions associated. Hence, this paper studies some variables that can influence the production of AAM based on spent FCC. Specifically, the influence of SiO2/Na2O molar ratio and the H2O/spent FCC mass ratio on the mechanical strength and microstructure are assessed. Some instrumental techniques, such as SEM, XRD, pH and electrical conductivity measurements, and MIP are performed in order to assess the microstructure of formed alkali-activated binder. Alkali activated mortars with compressive strength up to 80 MPa can be formed after curing for 3 days at 65 C. The research demonstrates the potential of spent FCC to produce alkali-activated cements and the importance of SiO2/Na2O molar ratio and the H2O/spent FCC mass ratio in optimising properties and microstructure., Authors would like to thank to the Ministerio de Ciencia e Innovacion (MICINN) of the Spanish Government (BIA2011-26947) and to FEDER for funding, and also to the PROPG - UNESP "Universidade Estadual Paulista Julio de Mesquita Filho'', Brazil.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of calcium aluminate cement (CAC) on alkaline activation of red clay brick waste (RCBW)

  • Reig Cerdá, Lucía
  • Soriano Martinez, Lourdes|||0000-0002-5749-4609
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
In this paper, the effect of calcium aluminate cement (CAC) additions on the alkali activation of red clay brick waste (RCBW) was studied at room temperature and at 65 C. RCBW was partially replaced with CAC (0e50 wt.%) and blends were activated with NaOH and sodium silicate solutions. The compressive strength evolution was tested on mortars and the nature of the reaction products was analysed by infrared spectroscopy, X-ray diffraction, thermogravimetric analysis, microscopic studies and pH measurements. The results show that the use of CAC accelerates the activation process of RCBW so that 50 MPa were obtained in the blended mortars containing 40 wt.% CAC cured for 3 days at room temperature. CAC did not undergo normal hydration and only the C3AH6 phase was identified in the pastes blended with more than 30 wt.% CAC and cured at 65 C, while the main reaction product was a cementitious gel containing Ca and Al from CAC., The authors are grateful to the Spanish Ministry of Science and Innovation for supporting this study through Project GEOCEDEM BIA 2011-26947, and to FEDER funding.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Carbon footprint of geopolymeric mortar: Study of the contribution of the alkaline activating solution and assessment of an alternative route

  • Mellado Romero, Ana María|||0000-0002-2105-154X
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
  • Catalan, C
  • Bouzón, N.
[EN] CO2 emissions associated with geopolymeric mortar prepared using spent fluid catalytic cracking catalyst (FCC) were compared to those calculated for plain ordinary Portland cement (OPC) mortar. Commercial waterglass used for preparing the alkaline activating solution for geopolymeric mortar was the main contributing component related to CO2 emission. An alternative route for formulating alkaline activating solution in the preparation of the geopolymeric binder was proposed: refluxing of rice husk ash (RHA) in NaOH solution. Geopolymeric mortar using rice hull ash-derived waterglass led to reduced CO2 emission by 63% compared to the OPC mortar. The new alternative route led to a 50% reduction in CO2 emission compared to geopolymer prepared with commercial waterglass. Replacement of commercial waterglass by rice hull ash- derived waterglass in the preparation of the geopolymer did not cause a significant decrease in the mechanical strength of the mortar. CO2 intensity performance indicators (Ci) for geopolymeric mortars were lower than that found for OPC mortar, indicating that the new route for activating solution led to the lowest C-i value, The authors are grateful to the Spanish Ministry of Economy and Competitiveness (Project GEOCEDEM BIA 2011-26947), and to Generalitat Valenciana (Project 3018/2009) and 'Centro de Cooperacion al Desarrollo' of the Universitat Politecnica de Valencia (ADSIDEO COOPERACIO, Project COMBURES) for supporting this study, and to DACSA S. A. for supplying RHA samples.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of calcium additiions on the compressive strength and microstructure of alkali-activated ceramic sanitaryware

  • Reig, L.
  • Soriano Martinez, Lourdes|||0000-0002-5749-4609
  • Mitsuuchi Tashima, Mauro|||0000-0003-0885-9293
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
[EN] The ceramic sanitary-ware market generates large amounts of waste, both during the production process and due to construction and demolition practices. In this paper, the effect of different amounts and calcium sources (calcium hydroxide Ca(OH)2, calcium aluminate cement CAC, Portland cement PC) on the alkaline activation of ceramic sanitary-ware waste (CSW) was assessed. Blended samples were activated with NaOH and sodium silicate solutions and cured for 3 and 7 days at 65°C. The maximum amount of calcium source-type added to the system varied according to its influence on the compactability of the mortars.CSW was physico-chemically characterized and the compressive strength development of activated samples was assessed on the mortars. The nature of the reaction products was analyzed in pastes, by X-ray diffraction, thermogravimetric analysis, infrared spectroscopy and microscopic studies. The results show a great positive influence with the addition of moderate amounts of Ca(OH)2, PC and CAC on the mechanical properties. Among the typical hydrates usually observed in plain water-hydrated PC or CAC, only AH3 and a small amount of C3AH6 were identified in the alkali-activated CSW/CAC blended pastes, which indicates that Al and Ca from PC, CAC and Ca(OH)2 are taken up in the newly formed (N,C)-A-S-H or C-A-S-H gels., Spanish Ministry of Science and Innovation, Grant/Award Number: APLIGEO BIA2015-70107-R, GEOCEDEM BIA 2011-26947; Electron Microscopy Service of the Universitat Politecnica de Valencia; FEDER
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Assesssment of pozzolanic/hydraulic reactivity of vitreous calcium aluminosilicate (VCAS) ussing different methods

  • Mitsuuchi Tashima, Mauro|||0000-0003-0885-9293
  • Soriano Martinez, Lourdes|||0000-0002-5749-4609
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
[EN] The aim of this paper is to assess the possibility of using vitreous calcium aluminosilicate (VCAS) as a supplementary cementitious material in the production of Portland cement mortars. The calcium hydroxide consumption by VCAS is assessed by two different methods: firstly, a classical method based on thermogravimetric analysis (TGA) and, secondly, pH and electrical conductivity measurements of calcium hydroxide/VCAS suspensions with excess calcium hydroxide. Evidence of pozzolanic reactivity of VCAS is revealed in hydrated lime pastes, and low reactivity was observed in aqueous suspensions. The reactivity of VCAS is also assessed by means of TGA of VCAS/ OPC pastes and by means of the mechanical strength development of Portland cement mortars, with VCAS replacement percentages in the range of 10 30%. The results obtained show that pozzolanic and hydraulic reactions take place in OPC systems. VCAS can be used as a supplementary cementitious material by replacing OPC at levels of 10 30% by mass., The authors are grateful to the Spanish Ministry of Science and Innovation for supporting this study through Project GEOCEDEM BIA 2011-26947, and to FEDER funding.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Properties and microstructure of alkali-activated red clay brick waste

  • Reig Cerdá, Lucía
  • Tashima, Mauro M.
  • Cheeseman, C.R.
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
Sintered red clay ceramic is used to produce hollow bricks which are manufactured in enormous quantities in Spain. They also constitute a major fraction of construction and demolition waste. The aim of this research was to investigate the properties and microstructure of alkali-activated cement pastes and mortars produced using red clay brick waste. The work shows that the type and concentration of alkali activator can be optimised to produce mortar samples with compressive strengths up to 50 MPa after curing for 7 days at 65 C. This demonstrates a new potential added value reuse application for this important waste material., The authors are grateful to the Spanish Ministry of Science and Innovation for supporting this study through Project GEOCEDEM BIA 2011-26947, and to FEDER funding. They also thank the Institute for Science and Technology of Concrete - ICITECH, for providing the means to carry out this investigation; and Universitat Jaume I, for supporting this research through the research stay granted.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Drying-rewetting cycles in ordinary Portland cement mortars investigated by electrical impedance spectroscopy

  • Fita Fernández, Inmaculada Concepción|||0000-0002-0927-3668
  • Cruz González, José Mª|||0000-0002-1672-6354
  • Soriano Martinez, Lourdes|||0000-0002-5749-4609
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
  • Calvo Muñoz, Clara
  • Sánchez Martín, Isidro
[EN] Changes caused in the porous microstructure of ordinary Portland cement (OPC) mortars were studied using electrical impedance spectroscopy (EIS) and equivalent circuit (EqC). Two successive processes, at 20 ºC and 50 °C, consisting of several drying-rewetting cycles, were applied to the mortars. After each cycle, the electrical impedance and the amount of water absorbed were measured. The EIS-EqC methodology allowed to find two distributed impedance relaxations, associated to capillary and gel-C-S-H porosities, respectively. At room temperature any microstructural change was not detected. Nevertheless, at 50 °C two microstructural changes were inferred: 1) the volume of accessible porosity increased (pore coarsening) and 2) the surface of the conductive path through C-S-H gel became more conductive (surface smoothing)., The authors would like to thank the Spanish Ministry of Science and Innovation for supporting this research through the project BIA 2011-26947.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Estudios preliminares sobre cemento hidratado para su reutilización en geopolímeros, Preliminary studies on hydrated cement for its reuse in geopolymers

  • Segura-Sierpe, Yasna Pamela
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
[EN] The carbonation of hydrated ordinary Portland cement (OPC) allows the transformation of hydrated calcium aluminates and silicates into calcium carbonate and amorphous silica/ alumina. These carbonated materials are appropriate to being used as inorganic precursors for alkaline activation. The use of sodium silicate and hydroxide solutions enables the production of cementitious gels. Two ways of carbonation of hydrated cement were studied: in a dry environment, where relative humidity did not exceed 70% and in an aqueous medium at a temperature of 5 ± 1 ° C. Both materials were micro-structurally characterised and they have been used for the manufacturing of geopolymeric mortars. These mortars reached mechanical strength between 10 and 20 MPa, depending on the activating solution, the water/binder ratio and curing time/temperature. These results show the feasibility of reusing hydrated cement contained in construction and demolition wastes., [ES] La carbonatación de cemento Pórtland hidratado permite la transformación de los silicatos y aluminatos cálcicos hidratados en carbonato cálcico y sílice/alúmina amorfas. Estos materiales carbonatados son susceptibles de ser usados como precursores inorgánicos para su activación alcalina. El uso de disoluciones de hidróxido y silicato sódico permite la obtención de geles cementantes. Se han estudiado dos vías de carbonatación de cemento hidratado: en un ambiente seco, donde la humedad relativa no sobrepasaba el 70 % y en un medio acuoso a temperatura de 5 ± 1 o C. Ambos materiales se han caracterizado microestructuralmente y han sido utilizados para la fabricación de morteros geopoliméricos. Estos morteros alcanzaron resistencias mecánicas entre 10 y 20 MPa, dependiendo de la disolución activadora, la relación agua/binder y del tiempo/temperatura de curado. Estos resultados demuestran la viabilidad de la reutilización de cemento hidratado presente en los residuos de construcción y demolición., Los autores agradecen al Ministerio de Ciencia e Innovación español por apoyar este estudio a través del Proyecto BIA2011-26947 y financiación FEDER. También agradecen a la Universidad de Magallanes, por apoyar esta investigación a través de la estancia de investigación concedida a Yasna Segura.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

novel geopolymeric material cured at room temperature

  • Mitsuuchi Tashima, Mauro|||0000-0003-0885-9293
  • Soriano Martinez, Lourdes|||0000-0002-5749-4609
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
[EN] Alkali activated binders are a new class of binding material with comparable or enhanced performance to Portland cement. These binding materials are obtained by a chemical reaction between an aluminosilicate material and a highly alkaline solution. In most cases, the setting hardening process of this binder is performed at high curing temperatures. In this paper, alkali activated mortars based on vitreous calcium aluminosilicate (VCAS) cured at room temperature are evaluated. Mechanical strength development and microstructural analysis (scanning electron microscopy, thermogravimetric analysis, X-ray diffraction and mercury intrusion porosimetry) of these materials are performed. Mortars yielded compressive strength ¡-89 MPa after 360 days. This is the first time that VCAS is used as aluminosilicate source material in the production of alkali activated mortars cured at room temperature., The authors acknowledge the Ministerio de Ciencia e Innovacio´ n of the Spanish Government (projecto. BIA2011-26947) and the Vitrominerals company for supplying VCAS samples.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Alkaline activation of ceramic waste materials

  • Reig Cerdá, Lucía
  • Soriano, L.
  • Mitsuuchi Tashima, Mauro|||0000-0003-0885-9293
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
Ceramic materials represent around 45 % of construction and demolition waste, and originate not only from the building process, but also as rejected bricks and tiles from industry. Despite the fact that these wastes are mostly used as road sub-base or construction backfill materials, they can also be employed as supplementary cementitious materials, or even as raw material for alkali-activated binders This research aimed to investigate the properties and microstructure of alkali-activated cement pastes and mortars produced from ceramic waste materials of various origins. Sodium hydroxide and sodium silicate were used to prepare the activating solution. The compressive strength of the developed mortars ranged between 22 and 41 MPa after 7 days of curing at 65 C, depending on the sodium concentration in the solution and the water/binder ratio. These results demonstrate the possibility of using alkaliactivated ceramic materials in building applications., The authors are grateful to the Spanish Ministry of Science and Innovation for supporting this study through Project GEOCEDEM BIA 2011-26947, and also to FEDER funding. They also thank Universitat Jaume I for supporting this research through Lucia Reig's granted research stay.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of the activator concentration and calcium hydroxide addition on the properties of alkali-activated porcelain stoneware

  • Reig Cerdá, Lucía
  • Soriano Martinez, Lourdes|||0000-0002-5749-4609
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
Objective The aim of this research was to investigate the influence of the alkali activator concentration and calcium dosage on the fresh behavior, compressive strength and microstructure of the binder produced by the alkali activation of porcelain stoneware waste, using NaOH and sodium silicate solution as activators. Materials Porcelain stoneware waste, NaOH and sodium silicate. Method Tested properties of mortars were the compressive strength and the setting times. Thermogravimetric analyses, microscopic studies, pH measurements, XRD and FTIR tests were used to assess the evolution of the microstructure developed. Results The results show that the activator concentration and calcium to sodium molar ratio strongly influence the fresh behavior and the hardening process of mortars. A linear evolution of compressive strength with sodium addition was observed when keeping the SiO2 concentration constant. Mortar samples with up to 36 MPa under compression were obtained after curing for 7 days at 65 °C., The authors are grateful to the Spanish Ministry of Science and Innovation for supporting this study through Project GEOCEDEM BIA 2011-26947, and to FEDER funding.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Compressive strength and microstructure of alkali-activated mortars with high ceramic waste content

  • Reig, L.
  • Sanz, M.A.
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
  • Soriano Martinez, Lourdes|||0000-0002-5749-4609
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
[EN] The present work investigated alkali-activated mortars with high ceramic waste contents. Tile ceramic waste (TCW) was used as both a recycled aggregate (TCWA) and a precursor (TCWP) to obtain a binding matrix by the alkali-activation process. Mortars with natural siliceous (quartz) and calcareous (limestone) aggregates, and with other ceramic waste materials (red clay brick RCB and ceramic sanitaryware CSW waste), were also prepared for comparison purposes. Given the lower density and higher water absorption values of the ceramic aggregates, compared to the natural ones, it was necessary to adapt the preparation process of the recycled mortars by presaturating the aggregate with water before mixing with the TCWP alkali-activated paste. Aggregate type considerably determined the mechanical behaviour of the samples cured at 65 °C for 3 days. The mortars prepared with the siliceous aggregate presented poor mechanical properties, even when cured at 65 °C. The behaviour of the limestone aggregate mortars depended heavily on the applied curing temperature and, although they presented the best mechanical properties of all those cured at room temperature, their compressive strength reached a maximum when cured at 65 °C, and then decreased. The mechanical properties of the mortars prepared with TCWA progressively increased with curing time (53 MPa at 65 °C for 28 days). An optimum 50 wt% proportion was observed for the limestone/TCWA mortars (¿43 MPa, 3 days at 65 °C), whereas the mechanical properties of that prepared with siliceous particles (10 MPa) progressively increased with the TCWA content, up to 100 wt% substitution (23 MPa). Limestone particles interacted with the binding matrix, and played an interesting beneficial role at the 20 °C curing temperature, with a slight reduction when cured long term (28 days) at 65 °C. The results demonstrated a potential added value for these ceramic waste materials., The authors would like to thank the Spanish Ministry of Science and Innovation and the Spanish Ministry of Economy and Competitiveness for supporting this study through Projects GEOCEDEM BIA 2011-26947 and BIA2015 70107-R, respectively. They also thank FEDER funding.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Ceramic tiles waste as replacement material in portland cement

  • Mas, María A.
  • Reig Cerdá, Lucía
  • Monzó Balbuena, José Mª|||0000-0002-3657-3076
  • Paya Bernabeu, Jorge Juan|||0000-0001-7425-5311
  • Borrachero Rosado, María Victoria|||0000-0002-7873-0658
The pozzolanic reactivity of real ceramic waste from different tile manufacturing companies was evaluated and its suitability as a partial Portland cement replacement was analysed. The raw material was finely ground and physicochemically characterised using X-ray fluorescence (XRF), X-ray diffraction (XRD), scanning electron microscopy (SEM) and laser analysis particle size distribution (ADL). Percentages of ceramic waste (from 15 wt% to 50 wt%) to substitute Portland cement were used to assess this material s pozzolanic behaviour, and samples were cured at 20°C for different curing times. pH tests and conductivity measurements were used to evaluate its pozzolanic character, while mortars were utilised to evaluate compressive strength behaviour. The microstructural evolution of the developed binders was assessed in pastes by XRD, thermal analysis, Fourier transform infrared spectroscopy (FTIR) and SEM analyses. A strength gain due to pozzolanic activity was observed after 28 d and 90 d curing. The results prove that mortars with up to 35 wt% of tile ceramic waste comply with the requirements established for fly ash pozzolanic materials., The authors are grateful to the Spanish Ministry of Science and Innovation for supporting this study through project GEOCEDEM BIA 2011-26947, and also to FEDER funding.