Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 13
Encontrada(s) 1 página(s)

Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publication Artículo científico (JournalArticle)

Stress-intensity factor solutions for embedded elliptical cracks in round bars subjected to tensile load

  • Alegre Calderón, Jesús Manuel
  • Cuesta Segura, Isidoro Iván
  • Díaz Portugal, Andrés
In this paper, stress-intensity factor solutions are presented for an embedded elliptical crack in a round bar subjected to tensile load. The stress-intensity factors (SIF) are presented in a tabulated form and were obtained from three-dimensional finite-element analyses of this crack configuration. The solutions provide the stress-intensity factor as a function of three dimensionless parameters representative of the crack size, the crack aspect ratio of the elliptical flaw and its relative position in the cross section. The dimensionless parameters cover ranges that allow most internal flaw shapes in practice to be considered. In order to validate the numerical model developed, some particular cases are compared with solutions of embedded elliptical flaws in different geometries available in the literature. Afterwards, a sequential methodology for fatigue crack growth is presented, including the conditions for the recategorization from the internal elliptical crack to a semi-elliptical surface crack. A comparison of the predicted crack paths with experimental results of fatigue crack propagation initiated from internal defects in round bars is also presented. This experimental validation shows the capability of the proposed SIF solutions for the study of the fatigue crack propagation initiated from internal defects in this geometry., JCyL project reference BU-002-P20, co-financed with FEDER funds.
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publication Artículo científico (JournalArticle)

Modelling hydrogenation during cold dwell fatigue of additively manufactured titanium alloys

  • Díaz Portugal, Andrés
  • Cuesta Segura, Isidoro Iván
  • Alegre Calderón, Jesús Manuel
Artículo publicado en el V. 34 dedicado a: The second European Conference on the Structural Integrity of Additively Manufactured Materials, Titanium alloys are widely employed in aerospace and automotive industries where lightweight applications are required. Additive Manufacturing (AM) processes have been proposed in order to reduce material waste and optimise mechanical properties. In addition, throughout these manufacturing processes and during service life, hydrogen uptake is expected, and the corresponding modification of mechanical properties needs to be modelled. Hydrogenation process including diffusion, trapping and hydride formation in a Ti-6Al-4V alloy during cold dwell fatigue loading, a common failure mode of titanium alloys, is simulated here. All governing equations are implemented in ABAQUS user subroutines. A boundary layer approach is used to simulate how hydrogen redistribution affects hydride kinetics near a blunting crack tip, in which cyclic loading is implemented considering different dwell times. The influence of AM techniques, especially Selective Laser Melting, is expected to promote the increase in martensite phase and microstructure defects due to rapid cooling; thus, the influence of martensite volume fraction and of trapping density on hydrogen redistribution near the crack tip is analysed. The possibility to implement hydrogen and hydride-induced dilatation is also presented, as well as a hydrogen-dependent localised plasticity model. This framework facilitates the prediction of how additive manufacturing processes affect susceptibility to hydrogen embrittlement in Ti-6Al-4V components subjected to dwell fatigue., The authors gratefully acknowledge financial support from the Junta of Castile and Leon through grant BU-002- P20, co-financed by FEDER funds.
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publication Artículo científico (JournalArticle)

Closed-form equations for the calculation of stress intensity factors for embedded cracks in round bars subjected to tensile load

  • Alegre Calderón, Jesús Manuel
  • Cuesta Segura, Isidoro Iván
  • Díaz Portugal, Andrés
Fatigue crack propagation initiated from internal defects is a typical mechanism observed in high cycle fatigue (HCF) and very high cycle fatigue (VHCF) of cylindrical tensile specimens subjected to uniaxial cyclic loads. To study the fatigue crack propagation of these embedded cracks by means of a fracture mechanics approach, solutions for the Stress Intensity Factor (SIF) for different crack configurations are needed. In this paper, a set of closed-form equations for the calculation of the SIF of embedded cracks in round bars subjected to tensile load is presented. Two sets of solutions are provided, which allow for different levels of approach to be considered. The first solution provides the SIF for the vertex points of an internal elliptical crack as a function of three dimensionless parameters related to crack size, crack position and crack aspect ratio. The second solution is a simplification for eccentric circular cracks located at any position of the cross section. The methodology necessary for the application to the study of fatigue crack propagation is also presented, and a comparison with those obtained from experimental tests is included, which exhibits a very good capacity for prediction., The authors gratefully acknowledge financial support from the Junta de Castilla y Leon (Spain) through grant BU-002-P20, co-financed by FEDER funds.
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publication Artículo científico (JournalArticle)

Effect of HIP post-processing at 850 °C/200 MPa in the fatigue behavior of Ti-6Al-4V alloy fabricated by Selective Laser Melting

  • Alegre Calderón, Jesús Manuel
  • Díaz Portugal, Andrés
  • García, Ricardo
  • Peral, Luis Borja
  • Cuesta Segura, Isidoro Iván
Hot Isostatic Pressing (HIP) is a thermomechanical post-processing technique widely used in Additive Manufacturing parts to reduce internal defects, such as entrapped-gas-pores or lack-of-fusion, which have a great influence on the mechanical and fatigue properties of the material. In this paper, the effect of a non-conventional HIP-cycle on the fatigue behavior of a Ti-6Al-4V alloy manufactured by Selective Laser melting (SLM) is studied. The HIP-cycle examined in this study is carried out at pressure of 200 MPa and a temperature of 850 ◦C for 2 h. Moreover, the cooling process is faster than that obtained from conventional furnace cooling rates, with the aim to limit the microstructural coarsening effects that affect the fatigue behavior. For the study, an extensive experimental fatigue program was carried out which included a first batch of SLM specimens tested under as-built conditions, a second batch of SLM specimens subjected to the present HIP process, and a third batch of specimens of a reference wrought processed material obtained by rolling and annealing processes. The microstructure of the material, before and after HIPping, is analyzed and a fractographic analysis is carried out to study the mechanism of crack initiation and its relation to the fatigue behavior. The results show that the present HIP-process allows for very good material densification, a microstructure that shows minimal coarsening effects, and good fatigue properties comparable to the conventional wrought processed material., The authors gratefully acknowledge financial support from the Junta de Castilla y León (Spain) through grant BU-002-P20, co-financed by FEDER funds.
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publication Artículo científico (JournalArticle)

Stress-intensity factor solutions for the simulation of fish-eye fatigue crack growth in round bars subjected to tensile load

  • Alegre Calderón, Jesús Manuel
  • Cuesta Segura, Isidoro Iván
  • Díaz Portugal, Andrés
Trabajo presentado en: The 7th International Conference on Crack Paths (CP 2021), organised by TC3 Fatigue of Engineering Materials and Structures of the European Structural Integrity Society (ESIS). The CP 2021 edition will take place in a virtual format (September 21st to 24th, 2021), The fatigue crack growth in round bars initiated from internal defects leads to the formation of a circular crack pattern usually so-called fish-eye. This failure mechanism is found in the current additive manufacturing techniques in which internal defects, such as pores or lack of fusion, are the main cause of fatigue crack initiation. Moreover, this fatigue mechanism becomes the predominant failure mode in the Very High Cycle Fatigue (VHCF) regime. With the aim of adequately studying these fatigue crack situations, this paper presents a set of solutions for the stress-intensity factor calculation for embedded elliptical cracks in a round bar subjected to tensile load. The stress-intensity factors (SIF) are presented in a tabulated form and were obtained from three-dimensional finite-element analyses. The SIF solutions are provided as a function of three dimensionless parameters that include the crack size, the crack aspect ratio, and its relative position in the cross section. After that, a sequential methodology for fatigue crack growth simulation is presented, and a comparison with experimental results of fatigue crack propagation initiated from internal defects in round bars is also presented. Finally, by varying the initial crack position and the initial crack aspect ratio, several aspects related to the evolution of the fatigue crack shape in this geometry are analyzed., The authors gratefully acknowledge financial support from the Junta de Castilla y Leon (Spain) through grant BU-002-P20, co-financed by FEDER funds.
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publication Artículo científico (JournalArticle)

Parameter Optimisation in Selective Laser Melting on C300 Steel

  • Cuesta Segura, Isidoro Iván
  • Díaz Portugal, Andrés
  • Rojo, M. A.
  • Peral, Luis Borja
  • Martínez, J.
  • Alegre Calderón, Jesús Manuel
Additive manufacturing (AM) of metallic materials is increasingly being adopted in numerous sectors, such as biomedicine, aerospace or automotive industries, due to its versatility in the creation of complex geometries and the minimisation of material waste when compared to traditional subtractive methods. In order to ensure a reliable operation of these parts, however, an in-depth study of the effect of additive manufacturing on mechanical properties, including tensile, fatigue and fracture resistance, is necessary. Among the vast number of methods and materials, this project is focused in one of the most promising techniques for the industry: Selective Laser Melting (SLM) for the production of a tools steel, in particular C300 steel components for the automotive sector. The main objective of this paper is to optimise some of the key parameters in the printing process, such as laser power, laser speed and hatch spacing. These variables are essential to obtain parts with good resistance. To that purpose, tensile tests were performed in 3D printed specimens, and then elastoplastic properties were extracted, organised and analysed through a design of experiments for the subsequent output fitting using the response surface methodology., This research was funded by: INVESTUN/22/BU/0003 // BU-002-P20 // MU-21-UP2021-030.
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publication Artículo científico (JournalArticle)

Soluciones del factor de intensidad de tensiones para fisuras elípticas internas en barras cilíndricas sometidas a esfuerzos de tracción

  • Alegre Calderón, Jesús Manuel
  • Cuesta Segura, Isidoro Iván
  • Díaz Portugal, Andrés
Comunicación presentada en: XXXVII Congreso del Grupo Español de Fractura GEF2021, celebrado de forma virtual los días 7 y 8 junio de 2021, Existe un gran número de aplicaciones en las cuales los defectos internos, como poros o inclusiones, son la principal causa de la iniciación de fisuras por fatiga en piezas de geometría cilíndrica. En este trabajo se presentan las soluciones del factor de intensidad de tensiones para fisuras elípticas internas en geometrías cilíndricas sometidas a esfuerzos de tracción. Las soluciones han sido obtenidas mediante un análisis por elementos finitos, y se presentan tabuladas en función de tres parámetros adimensionales: el tamaño de la fisura frente al radio de la pieza, la relación de aspecto de la fisura elíptica y la posición relativa de la misma. Para la validación del modelo numérico desarrollado, las soluciones aportadas se han comparado con una serie de soluciones representativas disponibles en la literatura. Posteriormente, y para que el análisis en fatiga de este tipo de componentes sea completo, se establecen las condiciones para la recategorización de la fisura elíptica interna en una fisura semielíptica superficial que permita continuar el cálculo en fatiga cuando el defecto interno alcance la superficie de la pieza. Finalmente, se presenta una comparación con resultados experimentales de la evolución del crecimiento de fisuras por fatiga iniciada a partir de defectos internos en probetas cilíndricas sometidas a cargas de tracción, lo que permite evaluar la capacidad de las soluciones proporcionadas para el análisis de crecimiento de grietas de fatiga en esta geometría., There is a large number of applications in which internal defects, such as pores or inclusions, are the main cause of the fatigue cracks initiation in round bars. This paper presents a set of stress intensity factor solutions for internal elliptical cracks in round bars subjected to tensile loads. Solutions have been obtained from a 3D finite element analysis, and are presented in a tabulated form as a function of three dimensionless parameters: the crack size to the radius of the round bar, the crack aspect ratio of the elliptical flaw and its relative position in the cross area. In order to validate the numerical model developed, some extreme situations are compared with solutions of embedded elliptical flaws in different geometries available in the literature. Afterward, and in order the fatigue analysis of this geometry to be complete, the conditions for the recategorization of the internal elliptical crack to a semi-elliptical surface crack are defined, that allows the fatigue crack growth calculation to be continued as the internal defect reaches the surface of the round bar. Finally, a comparison with experimental results of the evolution of fatigue crack growth initiated from internal defects in round bars subjected to tensile loads is presented. This experimental validation allows the capacity of the solutions provided for the analysis of growth of fatigue cracks in this geometry to be evaluated., Los autores desean agradecer la financiación recibida a través del proyecto de la JCyL referencia BU-002-P20, cofinanciada con fondos FEDER.
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publication Artículo científico (JournalArticle)

Efecto del postprocesado mediante HIP a 850ºC / 200 MPa en el comportamiento a fatiga de la aleación Ti-6AI-4V fabricada mediante SLM

  • Alegre Calderón, Jesús Manuel
  • García, Ricardo
  • Díaz Portugal, Andrés
  • Cuesta Segura, Isidoro Iván
Comunicación presentada en: 5th Iberian Conference on Structural Integrity que corresponde con el 38 Congreso del Grupo Español de Fractura GEF2022 celebrado en Coimbra, Portugal del 30 de marzo al 1 de abril de 2022, Hot Isostatic Pressing (HIP) es una técnica de postprocesado termomecánico ampliamente utilizada en piezas fabricadas mediante Selective Laser Melting (SLM) para densificar el material y reducir los defectos internos intrínsecos que se originan durante la fabricación, como porosidad o la falta de fusión, los cuales tienen un gran impacto en la resistencia a fatiga del material. En este trabajo se presenta el efecto de un ciclo HIP, realizado a una presión de 200 MPa y una temperatura de 850ºC durante 2 horas, sobre el comportamiento a fatiga de una aleación Ti-6Al-4V fabricada por SLM. Se ha efectuado un análisis defectológico y microestructural de las diferentes situaciones analizadas (SLM as-built, SLM+HIP, material de referencia) con el objetivo de estudiar la relación de los defectos y la microestructura con la vida en fatiga. Los resultados muestran que el presente proceso de HIP permite una muy buena densificación del material, y permite obtener una microestructura con mínimos efectos de engrosamiento de la fase α, lo cual se traduce en unas buenas propiedades de fatiga comparables a las del material de referencia., Hot Isostatic Pressing (HIP) is a thermo-mechanical post-processing technique widely used to reduce the internal defects characteristic of additive manufacturing techniques (lack-of-fusion or entrapped-gas-pores), which have a great impact on the fatigue properties of the material. In this work, the effect of a HIP-cycle at a pressure of 200 MPa and a temperature of 850ºC for 2 hours, on the fatigue behaviour of a Ti-6Al-4V alloy manufactured by SLM is presented. Microstructural and fractographic analysis for the different conditions (SLM as-built, SLM+HIP, reference material) have been carried out in order to study the effect of defects and microstructure features on the fatigue life. The results indicate that the present HIP process allows a very good densification of the material and exhibiting a microstructure with minimal alpha-phase coarsening effects, obtaining good fatigue properties comparable to the reference material ones., Los autores desean agradecer la financiación recibida a través del proyecto de la JCyL referencia BU-002-P20, cofinanciada con fondos FEDER.
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publication Artículo científico (JournalArticle)

Conjunto de ecuaciones para el cálculo del factor de intensidad de tensiones en fisuras internas de barras cilíndricas sometidas a tracción

  • Alegre Calderón, Jesús Manuel
  • Cuesta Segura, Isidoro Iván
  • Díaz Portugal, Andrés
Comunicación presentada en: 5th Iberian Conference on Structural Integrity que corresponde con el 38 Congreso del Grupo Español de Fractura GEF2022 celebrado en Coimbra, Portugal del 30 de marzo al 1 de abril de 2022, La propagación de fisuras por fatiga iniciadas a partir de defectos internos es uno de los principales mecanismos de fallo en piezas sometidas a alto número de ciclos (HCF) y muy alto número de ciclos (VHCF). La propagación de estos defectos internos en barras sometidas a esfuerzos de tracción tiende a adquirir una forma circular, independientemente de la forma irregular que presente el defecto iniciador, estableciendo un patrón conocido como fish-eye. Para el estudio de la propagación de este tipo de defectos se presenta en este trabajo un conjunto de ecuaciones que permiten obtener el factor de intensidad de tensiones (FIT) en función de tres parámetros adimensionales (tamaño, posición y relación de aspecto de la fisura). Se presenta también la metodología necesaria para su aplicación al estudio de la propagación de un defecto inicial. Los caminos de propagación calculados son comparados con los obtenidos en ensayos experimentales obteniendo una muy buena predicción, Fatigue crack propagation initiated from internal defects is one of the main mechanisms observed in components created using additive manufacturing techniques, as well as one of the most common mechanisms in high cycle fatigue (HCF). The propagation of these internal defects in round bars subjected to tensile loads tends to a circular shape, regardless of the irregular shape of the initiating defect, establishing a pattern known as fish-eye. In order to study the fatigue crack propagation of this type of defects, a series of closed-form equations are presented which allow the stress intensity factor (SIF) to be obtained in this geometry as a function of three dimensionless parameters (size, position and aspect ratio). The methodology necessary for its application to the study of fatigue crack propagation is also presented. The propagation paths calculated are compared with those obtained in experimental tests, obtaining a very good prediction., Los autores desean agradecer la financiación recibida a través del proyecto de la JCyL referencia BU-002-P20, cofinanciada con fondos FEDER.
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publication Artículo científico (JournalArticle)

Notch fracture predictions using the Phase Field method for Ti-6Al-4V produced by Selective Laser Melting after different post-processing conditions

  • Díaz Portugal, Andrés
  • Alegre Calderón, Jesús Manuel
  • Cuesta Segura, Isidoro Iván
  • Martínez Pañeda, Emilio
  • Zhang, Zhiliang
Ti-6Al-4V is a titanium alloy with excellent properties for lightweight applications and its production through Additive Manufacturing processes is attractive for different industrial sectors. In this work, the influence of mechanical properties on the notch fracture resistance of Ti-6Al-4V produced by Selective Laser Melting is numerically investigated. Literature data is used to inform material behaviour. The as-built brittle behaviour is compared to the enhanced ductile response after heat treatment (HT) and hot isostatic pressing (HIP) post-processes. A Phase Field framework is adopted to capture damage nucleation and propagation from two different notch geometries and a discussion on the influence of fracture energy and the characteristic length is carried out. In addition, the influence of oxygen uptake is analysed by reproducing non-inert atmospheres during HT and HIP, showing that oxygen shifts fracture to brittle failures due to the formation of an alpha case layer, especially for the V-notch geometry. Results show that a pure elastic behaviour can be assumed for the as-built SLM condition, whereas elastic-plastic phenomena must be modelled for specimens subjected to heat treatment or hot isostatic pressing. The present brittle Phase Field framework coupled with an elastic-plastic constitutive analysis is demonstrated to be a robust prediction tool for notch fracture after different post-processing routes., Financial support from the Junta of Castile and Leon through grant BU-002-P20, co-financed by FEDER funds. E. Martínez-Pañeda was supported by an UKRI Future Leaders Fellowship (grant MR/V024124/1). A. Díaz wishes to thank the Nanomechanical Lab of NTNU for providing hospitality during his research stay.
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publication Contribución de congreso (ConferenceOutput)

Mejora de las propiedades de materiales metálicos elaborados por fabricación aditiva mediante la técnica del Hot Isostatic Pressing. Caso de uso en industria

  • Alegre Calderón, Jesús Manuel
Ponencia presenta en: III Jornadas Técnicas Industrial Track 4.0, celebradas en el marco del Encuentro Tecnológico Burgos Industria 4.0 2022, organizadas por DIHBU y Promueve Burgos. Burgos, 25 y 26 de Octubre de 2022, Las técnicas de post-procesado termo-mecánico se utilizan para la mejora de las propiedades mecánicas y de fatiga de materiales producidos mediante fabricación aditiva. Con el proceso denominado Hot Isostatic Pressing (HIP) se consigue eliminar los defectos que se generan durante estos procesos industriales de fabricación aditiva, tales como el SLM o Binder Jetting. Se presentará la técnica y se mostrarán los resultados conjuntos de la colaboración entre el HIP Innovation Center de Hiperbaric y la Universidad de Burgos., Los autores desean agradecer la financiación recibida a través del proyecto de la JCyL referencia BU-002-P20, cofinanciada con fondos FEDER, y la colaboración de HIPERBARIC.
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publication Artículo científico (JournalArticle)

Modelling alpha case formation and embrittlement for Ti-6Al-4V produced by additive manufacturing and subjected to thermomechanical post-processing

  • Díaz Portugal, Andrés
  • Cuesta Segura, Isidoro Iván
  • Alegre Calderón, Jesús Manuel
Comunicación presentada en: 5th Iberian Conference on Structural Integrity que corresponde con el 38 Congreso del Grupo Español de Fractura GEF2022 celebrado en Coimbra, Portugal del 30 de marzo al 1 de abril de 2022, La Fabricación Aditiva permite la producción optimizada de geometrías complejas. Las propiedades de tracción entallada de la aleación Ti-6Al-4V se estudian numéricamente en este trabajo considerando el método de Selective Laser Melting (SLM) y diferentes condiciones de post-proceso. La formación de una capa frágil enriquecida con oxígeno o “alpha case” también se reproduce aquí para atmósferas no inertes aprovechando esquemas numéricos para el agrietamiento asistido por hidrógeno. La reducción local de la energía de fractura en función de la concentración de oxígeno se implementa en un modelo de Phase Field para la nucleación y propagación de grietas. Se modelizan diferentes probetas de tracción entallada en Comsol Multiphysics. El análisis es secuencial: la entrada y difusión de oxígeno se simulan para diferentes temperaturas y tiempos de permanencia, reproduciendo procesos típicos de SLM y HIP y diferentes presiones parciales de oxígeno. En un segundo paso, se simula el ensayo mecánico de tracción y se resuelve el problema de Phase Field considerando una reducción lineal de la tenacidad a fractura en función de la concentración de oxígeno. Se evalúan los efectos del valor de la longitud característica y del comportamiento plástico. Los resultados muestran que el marco numérico actual, después de una necesaria calibración de parámetros, es capaz de predecir la influencia del post-proceso termomecánico en la fractura de componentes entallados., Additive Manufacturing enables cost-effective production of complex geometries. Notched tensile properties of Ti-6Al4V alloy are here numerically studied considering the Selective Laser Melting (SLM) method and different postprocessing conditions. The formation of an oxygen-enriched brittle layer or an “alpha case” in Ti-6Al-4V is also reproduced for non-inert atmospheres. Exploiting other Finite Element frameworks for environmentally assisted cracking, e.g. hydrogen embrittlement models, the local reduction of fracture energy as a function of oxygen concentration is implemented in a Phase Field model for crack nucleation and propagation. Different notched tensile specimens are modelled in Comsol Multiphysics. The analysis is sequential: oxygen uptake and diffusion are simulated for different temperatures and dwell times, reproducing typical SLM and HIP processes and different partial pressures of oxygen. In a second step, mechanical tensile testing is simulated, and the damage Phase Field scheme is solved considering a linear reduction of fracture toughness as a function of oxygen concentration. The effects of the characteristic length value and of plastic behaviour are evaluated. Results show that the present framework, after parameter calibration, is able to predict the influence of thermomechanical post-processing on notch fracture., The authors gratefully acknowledge financial support from the Junta of Castile and Leon through grant BU002-P20, co-financed by FEDER funds.
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publication Artículo científico (JournalArticle)

Methodology to predict mechanical properties of PA-12 lattice structures manufactured by powder bed fusion

  • Rodríguez Aparicio, Rubén
  • Alegre Calderón, Jesús Manuel
  • Verbeeten, Wilco M.H.
  • Lorenzo Bañuelos, Miriam
  • Cuesta Segura, Isidoro Iván
Topology optimization for weight reduction of additive manufacturing parts is commonly achieved throughout the creation of lattice structures, typically generated with beams of small size cross-section. In order to carry out accurate simulations of these lattice structures, knowing the mechanical behavior of pillars is required. In this paper, a methodology for determining the mechanical properties of small size pillars printed in PA-12 material, using polymer powder bed fusion (PBF) and in particular the Selective Laser Sintering (SLS) technology, is presented. The effect of defects originated during the manufacturing process on the macroscopic mechanical properties is studied and the mechanisms which influence these properties are analyzed. A methodology for the determination of these properties is proposed, based on a successive correction of the printed nominal diameters according to two approaches; one due to the outer skin of unmelted material and the other due to internal melting defects. Once the material properties are determined, as a function of the cross-section of the lattice pillars, the numerical simulation of lattice-type structures has been carried out and the degree of adjustment of the proposed methodology has been experimentally verified, obtaining good results. This validation provides a reliable method for the simulation of the macroscopic behavior of lattice-type structures with reduced sizes, taking into account the intrinsic defects generated during the printing process., The authors wish to acknowledge the funding received through the Junta de Castilla y León projects BU-002-P20 and INVESTUN/22/BU/0003 co-financed with FEDER funds, and the projects MR5W.P3 (C17. I01. P01. S21) and MR4W.P2 co-financed by JCyL and MICINN and the NextGenerationEU/PRTR funds.