Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 17
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental comparison of DSB and CS-DSB mmW formats over a hybrid fiber and FSO fronthaul network for 5G

  • Bohata, J.
  • Nguyen, D.N.
  • Spacil, J.
  • Komanec, M.
  • Vallejo-Castro, Luis
  • Ghassemlooy, Z.
  • Zvanovec, S.
  • Ortega Tamarit, Beatriz|||0000-0003-1196-4756
[EN] The telecommunication world is experiencing the 5th generation (5G) networks deployment including the use of millimeter wave (mmW) frequency bands to satisfy capacity demands. This leads to the extensive use of optical communications, especially the optical fiber connectivity at the last mile access and the edge networks. In this paper we outline fiber and free space optics (FSO) technologies for use as part of the 5G optical fronthaul network. We investigate two different mmW transmission schemes based on (i) the conventional analog radio over fiber transmission using one Mach-Zehnder modulator (MZM) with double sideband (DSB) optical modulation, and (ii) an optical-based frequency doubling with one MZM biased at the null point to introduce carrier suppression DSB (CS DSB) transmission and second MZM used for data modulation. Both systems are assessed in terms of the error vector magnitude, signal-to-noise ratio, dynamic range and phase noise. We consider a configuration for the fronthaul network in the frequency range 2 (FR2) at 27 and 39 GHz with the scale of bandwidth up to 400 MHz with M-quadrature amplitude modulation and quadrature phase shift keying. Results are also shown for FR1 at 3.5 GHz. Moreover, we investigate for the first time the 5G new radio signal transmission under strong turbulence conditions and show the turbulence-induced FSO link impairment. We finally demonstrate the CS DSB scheme performs well under chromatic dispersion-induced fading for the frequency up to 40 GHz and single mode fiber length of 30 km, whereas the DSB format seems more appropriate for an antenna seamless transmission., European Cooperation in Science and Technology (CA19111); Ministerstvo Prumyslu a Obchodu (FV40089); Ceske Vysoke Uceni Technicke v Praze (SGS20/166/OHK3/3T/13).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Efficiency Analysis of a Truncated Flip-FBMC in Burst Optical Transmission

  • Bahaaelden, Mohammed S.
  • Pérez-Jiménez, Rafael
  • Renfors, Markku
  • Ortega Tamarit, Beatriz|||0000-0003-1196-4756
[EN] A novel Flip-filter bank multicarrier (Flip-FBMC)-based transmultiplexer (TMUX) with offset quadrature amplitude modulation is proposed to enhance the transmission performance compared to a conventional Flip-OFDM system. Moreover, the possibility to reduce the TMUX response (latency) and increase spectral efficiency is investigated for the first time through a tail shortening method. The proposed design is based on a biorthogonal form for visible light communication (VLC) to increase the flexibility of design requirements. However, spectral efficiency suffers from the ramp-up and the ramp-down at the beginning and end, respectively, of a data burst. Hence, as a penalty, Flip-FBMC imposes 9 more symbols than a Flip-OFDM packet and two factors compared to a DCO-FBMC burst. Hard truncation of the lowest energy tail minimizes latency and limits the system penalty to 2.5 symbols, which is lower than that of DCO-FBCM by 2 symbols. The results show that the prototype filter of the Heisenberg factor ( ¿1 ) is highly effective in reducing the energy loss of truncated tails and reduces the symbol error rate (SER). The Flip-FBMC gain over a direct line-of-sight VLC channel is analyzed, and the channel estimation of a truncated burst, which is based on the interference approximation method (IAM) of IAM-C type, exhibits a superior performance of 1.5 dB at 10 ¿3 SER over the IAM-R method and 1 dB at 10 ¿5 SNR over a cyclic prefix of 1 point Flip-OFDM. On the other hand, the analysis reveals that IAM-C is slightly impacted by the truncated burst compared to the nontruncated version., This work was supported in part by the Research Agency under Project RTI2018-101658-B-I00 and Project TEC2017-84065-C3-1-R, in part by the European Cooperation in Science and Technology COST Action "European Network on Future Generation Optical Wireless Communication Technologies (NEWFOCUS)'' under Grant CA19111, and in part by Generalitat Valenciana under Grant PROMETEO 2017/103.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Demonstration of M-QAM OFDM bidirectional 60/25 GHz transmission over 10 km Fiber, 100 m FSO and 2 m radio seamless heterogeneous fronthaul link

  • Vallejo, Luis
  • Nguyen, D.-N.
  • Guerra, C.
  • Bohata, J.
  • Spacil, J.
  • Zvanovec, S.
  • Ortega Tamarit, Beatriz|||0000-0003-1196-4756
  • Mora Almerich, José|||0000-0002-2877-4118
[EN] In this paper, we demonstrate the experimental transmission of 16-and 64-quadrature amplitude modulation (QAM) Long Term Evolution -Orthogonal Frequency Division Multiplexing (LTE-OFDM) signals by using mil-limetre wave frequencies at 60 GHz and 25 GHz for downlink and uplink, respectively, over a heterogeneous optical fronthaul infrastructure. A directly modulated laser was employed for both links, which enables the cost-effective full-duplex system proposal. The bidirectional link consists of a 10 km of single mode fiber, a 100 m long free space optics channel and 2 m long wireless radio link, which brings flexibility for future wireless networks. The error vector magnitude (EVM) parameter is measured for a range of the received optical and electrical power as well as the signal-to-noise ratio. A comprehensive estimation of penalty factors in the different network segments is presented. The successful transmission over the whole proposed network with the EVM below the required limit of 9 % for 64-QAM with 20 MHz bandwidth is experimentally demonstrated for the received optical power of-2.7 dBm and-1 dBm for the downlink and uplink, respectively., The research has been supported by the CTU in Prague SGS20/166/OHK3/3T/13, project from Ministry of Industry and Trade in Czech Republic (FV40089) and within COST action CA19111 (NEWFOCUS) . It has also been funded by the regional project from Generalitat Valenciana PROMETEO 2021/015 and Grant RTI2018-101658-B-I00 FOCAL by MCIN/AEI/10.13039/501100011033 and ERDF "A way of making Europe".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Tesis doctoral (DoctoralThesis)

Photonic Transceivers for 6G mmW-based Radio Access Networks

  • Botella-Campos, Marta|||0000-0002-1317-286X
[ES] Esta Tesis Doctoral se centra en el modelado, la implementación y la validación experimental de arquitecturas de enlace frontal fotónico reconfigurables para comunicaciones en banda de ondas milimétricas (mmW) en entornos interiores. La investigación se centra en en técnicas habilitadoras que aporten eficiencia energética, bajo coste y escalabilidad para sistemas de quinta generación (5G) y posteriores. Con este fin, este trabajo aprovecha el potencial de la fotónica de microondas para abordar los retos centrales de capacidad, latencia y heterogeneidad en las redes de nueva generación, demostrando que las señales mmW generadas fotónicamente, mediante modulación de intensidad (IM) y modulación de fase (PM), proporcionan una base práctica y escalable para enlaces frontales avanzados. Empleando la tecnología de radio-sobre-fibra analógica (ARoF), la Tesis Doctoral desarrolla y valida soluciones orientadas al despliegue de las futuras redes, conectando la teoría con la implementación a gran escala, impulsando técnicas habilitadoras tanto a nivel de transceptor como de arquitectura de red. El trabajo establece los principios fundamentales de la generación de señales mmW mediante modulación externa con supresión de portadora bajo esquemas IM y PM, obteniendo señales mmW sintonizables y de alta pureza espectral aptas para formatos de modulación avanzados. La formulación analítica y validación experimental de enlaces basados en un láser modulado directamente (DML) con un modulador Mach-Zehnder polarizado en portadora suprimida (CS-MZM) muestra hasta 23 dB de ganancia mmW relativa sobre 35 km de enlace de fibra gracias a la interacción entre el chirp del láser y la dispersión de la fibra e identifica las fronteras de transición entre regímenes de pequeña y gran señal, poniendo de relieve los equilibrios entre ganancia y linealidad. A partir de estos resultados, se proponen esquemas de transceptor basados en un mezclador y que no requieren precodificación para reducir el número de componentes y el coste preservando la operación de banda ancha y el cumplimiento de estándares. Además, se demuestra una arquitectura asistida por PM que habilita la multiplicación de frecuencia óptica, alcanzando 20 dB de ganancia mmW relativa en un enlace de 10 km. Este enfoque explota el filtrado óptico y la dispersión de la fibra para la conversión fase-intensidad, garantizando estabilidad de punto de polarización (bias), compatibilidad de multiplexor por división de onda densa (DWDM) y operación con componentes comerciales. Asimismo, una comparación amplia entre IM y PM concluye la ventaja de PM en cuanto a robustez frente a derivas de polarización y menores pérdidas de inserción. En las futuras redes de comunicaciones, la Tesis Doctoral aporta avances significativos para el desarrollo de redes heterogéneas convergentes y bidireccionales. Se demuestra un enlace frontal dúplex completo centralizado basado en PM con reutilización de portadora y distribución remota del oscilador local (LO), reduciendo la complejidad de la unidad de radio remota (RRH) y preservando la reconfigurabilidad y la compatibilidad DWDM. El sistema transporta señales 5G New Radio (NR) a 41 GHz/40 GHz en bajada/subida dentro de una red fibra-inalámbrica. Una evaluación comparativa de implementaciones dúplex completas IM y PM sobre enlaces híbridos fibra-óptica en espacio libre-radio demuestra rendimiento de extremo a extremo conforme a especificaciones estándar, pone de manifiesto diferencias de robustez y valida la reutilización centralizada de portadora de subida y la entrega remota de LO como mecanismos para simplificar los nodos de borde., [CA] Aquesta Tesi Doctoral se centra en el modelatge, la implementació i la validació experimental d'arquitectures de enllaç frontal fotònic reconfigurables per a comunicacions en banda d'ones mil·limètriques (mmW) en entorns interiors. La recerca posa l'èmfasi en tècniques habilitadores que aporten eficiència energètica, baix cost i escalabilitat per a sistemes de cinquena generació (5G) i més enllà. Amb aquest objectiu, el treball aprofita el potencial de la fotònica de microones per abordar els reptes nuclears de capacitat, latència i heterogeneïtat en les xarxes de nova generació, demostrant que les senyals mmW generades fotònicament, mitjançant modulació d'intensitat (IM) i modulació de fase (PM), proporcionen una base pràctica i escalable per a enllaços frontals avançats.\par Amb un enfocament en ràdio sobre fibra analògica (ARoF), la Tesi Doctoral desenvolupa i valida solucions orientades al desplegament que connecten la teoria amb la implementació a gran escala, impulsant tècniques habilitadores tant a nivell de transceptor com d'arquitectura de xarxa. El treball estableix els principis fonamentals de la generació de senyals mmW mitjançant modulació externa amb supressió de portadora sota esquemes IM i PM, obtenint senyals mmW sintonitzables i de gran puresa espectral aptes per a formats de modulació avançats. Una formulació analítica i la seua validació experimental d'enllaços basats en làser de modulació directa (DML) amb modulador Mach-Zehnder polaritzat amb supressió de portadora (CS-MZM), considerant la interacció entre el chirp del làser i la dispersió de la fibra, mostren fins a 23 dB de guany mmW relatiu al llarg de 35 km d'enllaç de fibra, i identifiquen les fronteres de transició entre règims de petita i gran senyal, posant de relleu els equilibris entre guany i linealitat.\par A partir d'aquests resultats, es proposen esquemes de transceptor sense precodificació i assistits per mesclador per reduir el nombre de components i el cost mantenint l'operació de banda ampla i el compliment d'estàndards. A més, es demostra una arquitectura assistida per PM que habilita la multiplicació de freqüència òptica, assolint 20 dB de guany mmW relatiu en un enllaç de 10 km. Aquest enfocament explota el filtrat òptic i la dispersió de la fibra per a la conversió fase¿intensitat, garantint estabilitat del punt de polarització (bias), compatibilitat DWDM (multiplexació per divisió densa en longitud d'ona) i operació amb components comercials. Així mateix, una comparació exhaustiva entre IM i PM conclou la superioritat de PM pel que fa a robustesa davant derivas de bias i menors pèrdues d'inserció. Pel que fa als aspectes d'arquitectura de xarxa, la Tesi Doctoral aporta avenços significatius cap al desenvolupament de xarxes heterogènies convergents i bidireccionals. Es demostra un enllaços frontal dúplex complet centralitzat basat en PM amb reutilització de portadora i distribució remota de l'oscil·lador local (LO), reduint la complexitat de la capçalera de ràdio remota (RRH) alhora que es preserven la reconfigurabilitat i la compatibilitat DWDM. El sistema transporta senyals 5G New Radio (NR) a 41 GHz/40 GHz en baixada/pujada dins d'una xarxa fibra-sense fils. Una avaluació comparativa d'implementacions dúplex completes IM i PM sobre enllaços híbrids fibra-FSO-ràdio demostra rendiment d'extrem a extrem conforme a especificació, posa de manifest diferències de robustesa i valida la reutilització centralitzada de portadora d'uplink i la distribució remota de LO com a mecanismes per simplificar els nodes de vora.\par, [EN] This Thesis focuses on modeling, implementing, and experimentally validating reconfigurable photonic fronthaul architectures for millimeter wave (mmW) indoor communications. The research emphasizes enabling techniques that deliver energy-efficient, cost-effective, and scalable access for fifth generation (5G) and beyond systems. To this end, this work harnesses the potential of microwave photonics to address the core challenges of capacity, latency, and heterogeneity in next-generation networks, demonstrating that photonically generated mmW signals, via intensity and phase modulation (IM and PM, respectively), provide a practical and scalable foundation for advanced fronthaul networks. Concentrating on analog radio-over-fiber (ARoF), the Thesis develops and validates deployment-oriented solutions that bridge theory and large-scale implementation, advancing enabling techniques at both the transceiver and network-architecture levels. The work establishes the fundamental principles of mmW signal generation using carrier-suppressed external modulation under IM and PM schemes, yielding tunable and spectrally pure mmW signals suitable for transmitting advanced modulation formats. The analytical formulation and experimental validation of directly modulated laser (DML)-based carrier-suppressed Mach-Zehnder modulator (CS-MZM) links demonstrates up to 23 dB relative mmW gain over 35 km of fiber link due to the interplay between the laser chirp and fiber dispersion; and also identifies the transition boundaries between small and large signal regimes, highlighting the trade-offs between gain and linearity. Based on this work, novel precoding free, mixer-assisted transceiver schemes are proposed to reduce component count and cost while preserving wideband operation and standards-compliant performance. Moreover, a PM-assisted architecture enabling optical frequency multiplication is demonstrated, achieving 20 dB relative mmW gain over a 10 km fiber link. This approach exploits optical filtering and fiber dispersion for phase-to-intensity conversion, ensuring bias stability, dense wavelength division multiplexer (DWDM) compatibility, and operation with commercial components. Furthermore, a comprehensive comparison between IM and PM approaches leads to the assessment of the superiority of the latter in terms of robustness against bias drift and insertion losses. With respect to network-level aspects, the Thesis delivers significant advances toward the development of future bidirectional and convergent heterogeneous networks. A centralized PM-based full-duplex fronthaul with carrier reuse and remote local oscillator (LO) delivery is demonstrated, reducing remote radio head (RRH) complexity while preserving reconfigurability and DWDM compatibility. The system enables 5G New-Radio (NR) standard signals over 41 GHz/40 GHz for downlink/uplink connectivity in a fiber-wireless network. A comparative evaluation of IM and PM full-duplex implementations across fiber-free space optics-radio hybrid links demonstrates specification-compliant end-to-end performance, stating robustness differences, and validating centralized uplink carrier reuse and remote LO delivery as mechanisms to simplify edge nodes. In addition, convergence is advanced through a dual-band fronthaul capable of simultaneously transporting baseband and mmW services over one fiber with clean post-detection separation and data rates up to 50 Mb/s and 100 Mb/s, respectively. The Thesis also demonstrates a unified fronthaul for a heterogeneous wireless access network that simultaneously delivers services by visible light communication (VLC) and mmW radio links achieving throughputs of 70 Mb/s for VLC and 400 Mb/s for mmW with negligible mutual interference under standardized test conditions., This research has been made possible through the support of several projects and institutions: • Predoctoral contract for University Teacher Training through Ministerio de Ciencia, Innovación y Universidades (FPU20/04717). • Project Grant PID2021-126514OBI00 “Sustainable optical technologies for millimeterwave and visible light communications access in 6G networks (OPTIMISE)” through MCIN/AEI and ERDF “A way of making Europe”. • Project PROMETEO 2021/015 “Disruptive Photonics Technologies for 2030” (Generalitat Valenciana). • European COST action CA19111 "Network on future generation optical wireless communication technologies (NEWFOCUS)".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Phase Modulation-based Fronthaul Network for 5G mmWave FR-2 Signal Transmission over Hybrid Links

  • Botella-Campos, Marta|||0000-0002-1317-286X
  • Mora Almerich, José|||0000-0002-2877-4118
  • Ortega Tamarit, Beatriz|||0000-0003-1196-4756
  • Bohata, Jan
  • Vallejo-Castro, Luis
  • Zvanovec, Stanislav
[EN] In this paper, we experimentally demonstrate the feasibility of a phase modulation (PM)-based analog optical mobile fronthaul network for seamless millimeter wave (mmWave) signal transmission over hybrid standard single-mode fiber (SSMF), free space optics (FSO) and radio links. As a proof of concept, a 64-QAM LTE signal has been transmitted over 25 GHz in a 10 km SSMF, 2 m FSO and 1 m radio link without the need for optical amplifiers. After fiber propagation, non-significant signal degradation has been obtained over the wireless links, with an estimated sensitivity level of received electrical power -45.8 dBm. Despite the advantages of PM-based approaches, the use of optical filtering in our system provides easy scalability by including dense wavelength division multiplexing (DWDM) schemes. Also, the comparison with direct intensity modulation (IM)-based approach allows to assess PM-approach as a promising solution for seamless mmWave signal transmission over future networks., This work has been supported TACR grant FW03010551 and within COST action CA19111 (NEWFOCUS). It has also been funded by Grant PID2021-126514OB-I00 OPTIMISE by MCIN/AEI/ 10.13039/501100011033 and ERDF A way of making Europe .
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A Scalable 26 GHz RoF Relay System Using Optoelectronic Extender

  • Bohata, Jan
  • Nguyen, Dong-Nhat
  • Dat, Pham Tien
  • Ghassemlooy, Zabih
  • Zvanovec, Stanislav
  • Ortega Tamarit, Beatriz|||0000-0003-1196-4756
[EN] This letter presents data transmission over a 26 GHz millimeter-wave (mmW) radio signal and its coverage extension in an indoor environment using the radio-over-fiber (RoF) technology. The proposed system consists of two RoF seamless wireless links to emulate a mobile fronthaul using a transparent RoF relay link to overcome higher attenuation of the mmW signal. The system is experimentally evaluated for up to 64-quadrature amplitude modulation (QAM), showing the possibility of signal transmission over up to 20 km of optical fiber in the first Section transmission scheme without the usage of an optical amplifier. For the system with 20 km and 30 m long RoF links as well as 4 m and 1 m long relays with no optical amplification, the minimal experimentally measured error vector magnitude is as low as 5% for 64-QAM. Further, a self-developed integrable optoelectronic extender is used for the relay RoF system to simplify the antenna site and keep its footprint small. Moreover, the proposed setup is extended using an optical amplifier toward a scalable scheme with up to 75 km of optical fiber and 5 m long free space optical link., This work was supported in part by the Czech Science Foundation under Grant GA22-32180S and in part by the European Cooperation in Science andTechnology (COST) Project under Grant CA19111 NEWFOCUS.(Jan Bohataand Dong-Nhat Nguyen contributed equally to this work.)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Photonics-based full duplex millimeter-wave fronthaul links for future mobile communications

  • Botella-Campos, Marta|||0000-0002-1317-286X
  • Mora Almerich, José|||0000-0002-2877-4118
  • Ortega Tamarit, Beatriz|||0000-0003-1196-4756
  • Bohata, Jan
  • Vallejo-Castro, Luis
  • Vocílka, Jan
  • Nguyen, Dong-Nhat
  • Zvanovec, Stanislav
[EN] This paper presents the viability of two different approaches based on external modulation for millimeter wave (mmW) signal generation that are demonstrated over two full duplex photonic fronthaul schemes. Both intensity and phase modulation are demonstrated as effective techniques for mmW signal generation and also, in both cases, local oscillator remote delivering is provided, whereas a centralized scheme provides an optical carrier for uplink which is delivered from the central station. Wireless transmission is performed through both radio and free-space optics links. Experimental transmission results with QPSK and 64-QAM test model signals show both solutions as promising for the future mobile communication networks., This work has been supported by COST action CA19111 (NEWFOCUS) and Grant PID2021-126514OB-I00 OPTIMISE by MCIN/AEI/10.13039/501100011033 and ERDF A way of making Europe and TACR grant : FW07010035.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

On the 40 GHz Remote Versus Local Photonic Generation for DML-Based C-RAN Optical Fronthaul

  • Vallejo-Castro, Luis
  • Nguyen, Dong-Nhat
  • Bohata, Jan
  • Zvanovec, Stanislav
  • Mora Almerich, José|||0000-0002-2877-4118
  • Almenar Terre, Vicenç|||0000-0002-8742-2315
  • Ortega Tamarit, Beatriz|||0000-0003-1196-4756
[EN] Local and remote photonic millimeter wave (mmW) signal generation schemes are theoretically and experimentally evaluated in order to compare both approaches for practical deployment in a cloud radio access network (C-RAN) fronthaul network. The paper presents a full comprehensive formulation of the frequency response of a system based on a directly modulated laser transmitting data over 40 GHz signal which is generated by external carrier suppressed modulation and optical frequency multiplication. Theoretical and experimental characterization of the system response at baseband and mmW band for local and remote generation setups show very good agreement. The remote configuration leads to a higher electrical output power (i.e., 15 dB higher in 25 km fiber links) than the local generation setup in the mmW band due to the combined effect of chirp and fiber dispersion, although intermodulation distortion is higher in the former case. Transmission experiments using quadrature phase-shift keying (QPSK) signals with 250 MHz bandwidth centered at 0.5 GHz over 10 and 25 km fiber links also confirm the superior performance of the remote setup, whereas the local setup leads to similar results to optical back-to-back (OB2B) measurements, which is also validated with data signals centered at different frequencies within the laser bandwidth frequency range. Finally, experimental results show the quality of the recovered signals in terms of error vector magnitude (EVM) as a function of the received electrical power and demonstrate that no further penalties are introduced by photonic mmW signal generation with respect to electrical back-to-back (EB2B) levels., This work was supported in part by Generalitat Valenciana through PROMETEO2017/103, in part by Ministerio de Ciencia, Innovacion y Universidades through FOCAL RTI2018-101658-B-I00, in part by MEYES under Grant LTC18008, in part by the Ministry of Industry and Trade in Czech Republic under Grant FV40089, and in part by European Cooperation in Science and Technology under Grants CA16220 and CA19111.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Asymmetric hybrid full-duplex POF-based VLC transmission links

  • Apolo-Gonzaga, Juan Andres
  • Almenar Terre, Vicenç|||0000-0002-8742-2315
  • Ortega Tamarit, Beatriz|||0000-0003-1196-4756
  • Teli, Shivani Rajendra
  • Guerra-Yánez, Carlos
  • Zvánovec, Stanislav
[EN] This paper presents an asymmetric full-duplex solution based on visible light communications (VLC) for indoor wired and wireless hybrid signal transmission. The signal is distributed by a polymer optical fiber (POF) link and passively radiated. The proposed system includes two VLC links: a low-speed downlink and a high-speed uplink using an image sensor (IS) and photodiode detection (PD) based receivers. PD-based system communication performance is evaluated by means of error vector magnitude (EVM) for different modulation orders quadrature phase shift keying (QPSK), 16- and 64-quadrature amplitude modulation (QAM), while the IS-based system is characterized in terms of the success of reception (SoR). High-speed data transmission up to 160 Mbps with a 16-QAM modulation scheme and low-speed data transmission up to 500 bps with 98.6% of SoR using a non-return zero on¿off keying (NRZ-OOK) scheme over a 1.5 m optical wireless link are demonstrated. Finally, simulations of the wireless channel are performed to evaluate the misalignment tolerance of the system; and, to estimate the uplink performance at longer distances., This work was based upon work from COST Action CA19111 (European Network on Future Generation Optical Wireless Communication Technologies, NEWFOCUS), supported by COST (European Cooperation in Science and Technology), and also supported by MCIN/AEI/10.13039/501100011033 and ERDF A way of making Europe under Grant RTI2018-101658- B-I00 FOCAL, and also supported by the Czech Technical University in Prague under the CTU Global Postdoc Fellowship Program and TACR project FW01010571.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Optical CS-DSB Schemes for 5G mmW Fronthaul Seamless Transmission

  • Bohata, Jan
  • Vallejo-Castro, Luis
  • Zvanovec, Stanislav
  • Ortega Tamarit, Beatriz|||0000-0003-1196-4756
[EN] This paper describes the experimental demonstration of the hybrid optical/millimeter wave signal generation and transmission over combined optical fiber and free space optics fronthaul network with a seamless antenna link. An electrical bandpass filter is used to filter out the spectrum after photodetection in order to realize the seamless antenna transmission. The successful transmission of 64/256-quadrature amplitude modulation (QAM) 5G signal with up to 200 MHz bandwidth is presented by using two different setups: one is based on two Mach-Zehnder modulators (MZM) and the other employs a directly modulated laser (DML) to provide more cost efficient fronthaul solution. The DML based approach reveals mildly better performance in comparison to the MZMs in terms of higher achieved signal-to-noise ratio and lower error vector magnitude (EVM). More specifically, the best signal-to-noise ratio and EVM achieved with the DML based setup has been 31.5 dB and 3. 3%, respectively, compared to 30.3 dB and 3.8% with the MZMs based setup while transmitting 256-QAM signal with 100 MHz bandwidth. However, both setups kept the EVM well below the given 9% and 4.5% limit for 64- and 256-QAM, respectively., This work was supported in part by the Ministry of Industry and Trade in Czech Republic under Grant FV40089, in part by EU COST Action NEWFOCUS under Grant CA19111, and in part by the Ministerio de Ciencia, Innovacion y Universidades under Grant FOCAL RTI2018-101658-B-I00.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental demonstrations of high-accuracy 3D/2D indoor visible light positioning using imaging multiple-input multiple-output receivers and artificial neural networks

  • Apolo-Gonzaga, Juan Andrés
  • Ortega Tamarit, Beatriz|||0000-0003-1196-4756
  • Almenar Terre, Vicenç|||0000-0002-8742-2315
  • Osahon, Isaac. N. O.
  • Tang, Jianming
  • Rajbhandari, Sujan
[EN] This paper proposes and presents the first experimental demonstration of a high-precision indoor 2D and 3D visible light positioning (VLP) system using an imaging multiple-input multiple-output (MIMO) configuration with supervised artificial neural network. The proposed system utilises four distributed transmitters and receiver with four photodiodes and an imaging optics. The experiments are conducted in a typical indoor environment with transmitter separations of 300 mm and a link distance of 1400 mm. The experimental results show 2D and 3D positioning accuracies of 3.7 and 51 mm, respectively. A simulation model is also developed for the VLP system to validate the experimental results. Further optimisation of the VLP system in the simulation platform leads to improved 2D and 3D positioning accuracies of 2 and 14.7 mm, respectively. The proposed system can be seamlessly integrated with existing lighting infrastructures and is also compatible with the MIMO visible light communication system, indicating the potential for practical implementation in integrated communications and positioning applications., This work has been supported by COST action CA19111 (NEWFOCUS). It has also been funded by Grant PID2021-126514OB-I00 optimise by MCIN/AEI/10.13039/501100011033 and ERDF 'A way of making Europe'. SR and JT acknowledge support by the UK Engineering and Physical Sciences Research Council under Grant EP/Y037243/1 (TITAN Extension).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Full-duplex transmission of multi-Gb/s subcarrier multiplexing and 5G NR signals in 39 GHz band over fiber and space

  • Nguyen, Dong-Nhat
  • Vallejo-Castro, Luis
  • Dat, Pham Tien
  • Le, Son Thai
  • Bohata, Jan
  • Zvanovec, Stanislav
  • Almenar Terre, Vicenç|||0000-0002-8742-2315
  • Ortega Tamarit, Beatriz|||0000-0003-1196-4756
[EN] We propose a stable full-duplex transmission of millimeter-wave signals over a hybrid single-mode fiber (SMF) and free-space optics (FSO) link for the fifth-generation (5G) radio access networks to accelerate the Industry 4.0 transformation. For the downlink (DL), we transmit 39 GHz subcarrier multiplexing (SCM) signals using variable quadrature amplitude modulation (QAM) allocations for multi-user services. As a proof of operation, we experimentally demonstrate the transmission of 3 Gb/s SCM signals (1 Gb/s per user) over a hybrid system consisting of a 10 km SMF and 1.2 m FSO link. For the uplink (UL), satisfactory performance for the transmission of 2.4 Gb/s 5G new radio (NR) signal at 37 GHz over the hybrid system is experimentally confirmed for the first time, to the best of our knowledge. The measured error vector magnitudes for both DL and UL signals using 4/16/64-QAM formats are well below the third generation partnership project (3GPP) requirements. We also further evaluate by simulation the full-duplex transmission over the system in terms of received optical and RF powers and bit error rate performance. A wireless radio distance of approximately 200 m, which is sufficient for 5G small-cell networks, is estimated for both DL and UL direction under the heavy rain condition, based on the available data from Spain. Furthermore, simulation for the DL direction is conducted to verify the superior performance of the system using variable QAM allocation over uniform QAM allocation. Using a variable modulation allocation, up to five users (2 Gb/s per user) can be transmitted over a hybrid 10 km SMF and 150 m FSO link., Ceske Vysoke Uceni Technicke v Praze (SGS20/166/OHK3/3T/13); European Cooperation in Science and Technology (CA19111 NEWFOCUS).
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

Combined infrared-ultrasonic positioning system to improve the data availability

  • Aparicio Esteve, Elena|||0000-0001-7886-312X
  • Ureña Ureña, Jesús|||0000-0003-1408-6039
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Villadangos Carrizo, José Manuel|||0000-0001-5900-0978
This work was supported in part by MCIN/AEI/10.13039/501100011033 and EU “NextGenerationEU”/PRTR (ref. TED2021-131773B-I00) Proyectos, Many indoor positioning applications related to accurate monitoring and tracking targets require centimeter precision. Infrared (IR)- and ultrasound (US)-based systems represent a feasible approach providing high robustness against interference. Furthermore, their combination may achieve better performance by mitigating their complementary drawbacks, covering larger areas, and improving the availability of positioning measurements. In this context, this work presents the proposal and experimental evaluation of a tightly coupled fusion method that uses an extended Kalman filter (EKF) to merge an IR- and a US-based positioning system. An outlier detection method is considered to select measurements with an adequate performance. Experimental results reveal that the IR and US systems are unable to position in 4.08% and 26.06% of locations, whereas the combined IR -US system has 100% of availability. In addition, the merged solution achieves less than 4 cm of positioning error in 90% of cases, outperforming the IR and US systems when they work independently., Agencia Estatal de Investigación, Universidad de Alcalá, European Commission
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

Activity monitoring and location sensory system for people with mild cognitive impairments

  • García Requejo, Alejandro|||0000-0002-4955-8852
  • Pérez Rubio, María del Carmen|||0000-0001-8271-6843
  • Villadangos Carrizo, José Manuel|||0000-0001-5900-0978
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
Cognitive impairment diseases are becoming more and more prevalent mainly due to population ageing and the increase in life expectancy. Sensory and monitoring systems may allow people with mild cognitive impairments (MCI) or at early stages of dementia to live at home for longer with more independence and security. This work presents a Wireless Sensor Network (WSN) based on wearables that obtains indoor and outdoor location and step information, reporting them over a LoRaWAN network. Each Wireless Wearable Sensor (WWS) uses a Global Navigation Satellite System module for outdoor positioning, a proposed indoor roomlevel localization system based on infrared sensors, an accelerometer for a step detector algorithm, and a LoRa (Long-Range) radio link to send the measured information with low power consumption achieving a large coverage range. These sensory data are recorded in a database and presented to the medical services and caregivers through a user web application. This can be used to detect anomalous changes in daily patients? routines, as well as to know the user?s position in cases where the patient may be disoriented. In addition, alerts are launched in caregivers? smartphones to report about any risky situation, such as the patient leaving an allowed area or staying in one place for too long. Therefore, the proposed sensory system may support and extend the ability of people with MCI or at early stages of dementia to live independently, it helps detect behavioural changes and it keeps caregivers? peace of mind., European Commission, Agencia Estatal de Investigación, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Artículo científico (JournalArticle)

Slotted Aloha With Capture for OWC-Based IoT: Finite Block-Length Performance Analysis

  • Devaja, Tijana
  • Petkovic, Milica
  • Escribano Aparicio, Francisco Javier|||0000-0002-7648-2734
  • Stefanovic, Cedomir
  • Vukobratovic, Dejan
In this paper, we analyze the throughput and reliability of an indoor optical wireless communication (OWC)-based Internet of Things (IoT) system based on Slotted ALOHA (SA) where IoT devices exchange data with an access point (AP). Assuming that the OWC receiver at the AP exploits the capture effect, we derive the error probability of decoding a short-length data packet that originates from randomly selected OWC IoT device in the presence of interfering users. The analysis is based on the derivation of the signal-to-interference-plus-noise-ratio (SINR) statistics and the application of the finite block-length (FBL) information theory. Using these analytical results, we derive relevant performance parameters such as the system throughput and reliability expressed in terms of the outage probability of a user transmission. The main trade-offs between the system performance and the OWC system setup parameters are investigated, in particular, by stressing how the indoor OWC-based system geometry plays an important role in the system performance.Using extensive numerical results, we clearly describe how the presented results are used to optimize the SA-based indoor OWC IoT system design., European Union, European Cooperation in Science and Technology
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Libro o Monografía (Book)

Centralized optical 3D positioning system for emitting tags

  • Aparicio Esteve, Elena|||0000-0001-7886-312X
  • Ureña Ureña, Jesús|||0000-0003-1408-6039
  • Hernández Alonso, Álvaro|||0000-0001-9308-8133
  • Moltó Orozco, David|||0000-0002-2790-3758
  • Villadangos Carrizo, José Manuel|||0000-0001-5900-0978
  • Cubero Vacas, Miguel
13th International Conference on Indoor Positioning and Indoor Navigation (IPIN2023), 25-28 September 2023, Nuremberg, Germany., The demand for accurate and reliable local positioning systems has grown rapidly with the increasing use of Location-Based Services (LBS). Emerging technologies such as optical, RF, acoustic, mechanical, and magnetic are feasible options for indoor positioning. Optical-based systems have gained attention due to the widespread LED lamp availability and centimeter-level accuracy. In this context, this work presents the implementation and validation of a centralized optical Local Positioning System (LPS) based on a set of mobile emitter LEDs and a minimum of two fixed receivers, enabling simultaneous position of all tags in the infrastructure (centralized approach). The system is designed for long-distance measurements, using Visible or Infrared Light signals. By incorporating geometric considerations into a Non-Linear Least Squares Estimator (NLSE), the system can estimate the 3D position of a mobile object (i.e. person, drone). The comparison of different deployments demonstrates that the proposed system estimates the 3D position with less than 4mm of error in 90% of cases when using four non-aligned receivers and a single LED., Agencia Estatal de Investigación, Universidad de Alcalá, Junta de Comunidades de Castilla-La Mancha, European Commission
e_Buah Biblioteca Digital Universidad de Alcalá
Publication Contribución de congreso (ConferenceOutput)

Reliability Analysis of Slotted Aloha with Capture for an OWC-based IoT system

  • Devaja, Tijana
  • Petkovic, Milica
  • Vukobratovic, Dejan
  • Escribano Aparicio, Francisco Javier|||0000-0002-7648-2734
  • Stefanovic, Cedomir
2021 17th International Symposium on Wireless Communication Systems (ISWCS), 06/09/2021-09/09/2021, Berlin, Alemania, In this article, we consider a random access scheme for an indoor Internet of Things (IoT) framework that uses optical wireless communication (OWC). We focus on a Slotted ALOHA (SA)-based solution where a number of OWC IoT users contend to send data to a central OWC receiver. In any given slot, and for a randomly selected active user, we consider the reliability of decoding the user?s data packet at the receiver. This is done by deriving the signal-to-noise-and-interference-ratio (SINR) statistics from a randomly chosen user and evaluating the probability that the user?s SINR is below a given threshold. By placing our analysis in the context of an indoor OWC IoT uplink setup, and employing the standard OWC channel model, we investigate the trade-offs between the reliability and the OWC system parameters such as the cell area or the transmitter?s semi-angle. We obtain valuable insights into the design of an SA-based random access solution for a typical indoor OWC cell. © 2021 IEEE, European Union