Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 15
Encontrada(s) 1 página(s)

Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publication Artículo científico (JournalArticle)

Filamentous bacteria existence in aerobic granular reactors

  • Figueroa Leiro, Mónica
  • Val del Río, Ángeles
  • Campos Gómez, José Luis
  • Méndez Pampín, Ramón José
  • Mosquera Corral, Anuska
Filamentous bacteria are associated to biomass settling problems in wastewater treatment plants. In systems based on aerobic granular biomass they have been proposed to contribute to the initial biomass aggregation process. However, their development on mature aerobic granular systems has not been sufficiently studied. In the present research work, filamentous bacteria were studied for the first time after long-term operation (up to 300 days) of aerobic granular systems. Chloroflexi and Sphaerotilus natans have been observed in a reactor fed with synthetic wastewater. These filamentous bacteria could only come from the inoculated sludge. Thiothrix and Chloroflexi bacteria were observed in aerobic granular biomass treating wastewater from a fish canning industry. Meganema perideroedes was detected in a reactor treating wastewater from a plant processing marine products. As a conclusion,the source of filamentous bacteria in these mature aerobic granular systems fed with industrial effluents was the incoming wastewater.
Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publication Artículo científico (JournalArticle)

Effects of Inoculum Type and Aeration Flowrate on the Performance of Aerobic Granular SBRs

  • Jungles, Mariele K.
  • Val del Río, Ángeles
  • Mosquera Corral, Anuska
  • Campos Gómez, José Luis
  • Méndez Pampín, Ramón José
  • Costa, Rejane H. R.
Aerobic granular sequencing batch reactors (SBRs) are usually inoculated with activated sludge which implies sometimes long start-up periods and high solids concentrations in the effluent due to the initial wash-out of the inoculum. In this work, the use of aerobic mature granules as inoculum in order to improve the start-up period was tested, but no clear differences were observed compared to a reactor inoculated with activated sludge. The effect of the aeration rate on both physical properties of granules and reactor performance was also studied in a stable aerobic granular SBR. The increase of the aeration flow rate caused the decrease of the average diameter of the granules. This fact enhanced the COD and ammonia consumption rates due to the increase of the DO level and the aerobic fraction of the biomass. However, it provoked a loss of the nitrogen removal efficiency due to the worsening of the denitrification capacity as a consequence of a higher aerobic fraction
Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publication Artículo científico (JournalArticle)

Effect of Coagulant-Flocculant Reagents on Aerobic Granular Biomass

  • Val del Río, Ángeles
  • Morales Pereira, Nicolás
  • Figueroa Leiro, Mónica
  • Mosquera Corral, Anuska
  • Campos Gómez, José Luis
  • Méndez Pampín, Ramón José
BACKGROUND: Technologies based on aerobic granular biomass are presented as a new alternative for its application to the wastewater treatment due to its advantages in comparison with the conventional activated sludge ones. However the properties of the aerobic granules can be influenced by the presence of residual amounts of coagulant-flocculant reagents, frequently used as pre-treatment before the biological process. In this work the effect of these compounds on aerobic granular biomass development was tested. RESULTS: The presence of coagulant-flocculant reagents led to a worse biomass retention capacity with a lower VSS concentration compared to a control reactor (4.5 vs. 7.9 g VSS/L) and with a higher SVI (70 vs. 40 mL/g TSS) and diameter (5.0 vs. 2.3 mm). These reagents also caused a decrease in the maximum oxygen consumption rate, but the removal efficiencies of organic matter (90%) and nitrogen (60%) achieved were similar than the control reactor. CONCLUSION: The continuous presence of residual levels of coagulant-flocculant reagents from the pre-treatment unit negatively affected the formation process and the physical properties of the aerobic granules, however the removal of organic matter and nitrogen were not affected
Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publication Artículo científico (JournalArticle)

Stability of aerobic granular biomass treating the effluent from a seafood industry

  • Val del Río, Ángeles
  • Figueroa Leiro, Mónica
  • Mosquera Corral, Anuska
  • Campos Gómez, José Luis
  • Méndez Pampín, Ramón José
The aerobic granular systems represent a good alternative to substitute the conventional activated sludge process in the treatment of industrial effluents due to the lower surface requirements. In this work the effluent from a seafood industry, characterized by a high variability and the presence of residual amounts of coagulant and flocculant reagents, was used to study the development of aerobic granular biomass and its stability. In a first stage with OLRs between 2 and 5 kg CODS/m3∙d the development of aerobic granular biomass was promoted with good physical properties: SVI of 35 mL/g TSS, density of 60 g VSS/Lgranule and average diameter of 2.8 mm. In a second stage the continuous change in the OLR applied from 3 to 13 kg CODS/m3∙d, to simulate the real conditions of the industry, showed that the removal of organic matter was not affected (90%) but the aerobic granules disintegrated. The maximum OLR treated in the system without granules disintegration was around 4.4 kg CODS/m3∙d. The nitrogen removal was 30% (for biomass assimilation) and the maximum ammonia removal was around 65% and depending on the solids retention time, the free ammonia concentration and the average granule diameter
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Cathode potential and anode electron donor evaluation for a suitable treatment of nitrate-contaminated groundwater in bioelectrochemical systems

  • Pous Rodríguez, Narcís
  • Puig Broch, Sebastià
  • Balaguer i Condom, Maria Dolors
  • Colprim Galceran, Jesús
Several regions around the world present high levels of nitrate in groundwater. Due to its toxicity, nitrate must be removed before the groundwater is used as drinking-water. This study assessed how a denitrifying bioelectrochemical system could be operated to treat nitrate-polluted groundwater. It evaluated the cathode potential (from +597 to -703mV vs SHE) and the anode electron donor (acetate and water). Similar trends were found regardless of the anode electron donor. The nitrate removal rate increased from 1.05 to 5.44mgN-NO3 -LNCC -1h-1 when the cathode potential was lowered from +597 to -403mV vs SHE, where it stabilized. The nitrate reduction end-products (nitrite, nitrous oxide and dinitrogen gas) also changed with the different potentials of the cathode electrode. The World Health Organization nitrates and nitrites standards for drinking-water were reached at cathode potentials between -103 and -203mV vs SHE. The highest rate of nitrate conversion to N2 (2.59mgN-NO3 -LNCC -1h-1, 93.9%) occurred at -123mV using water as anode electron donor, with an estimated operational cost similar to conventional technologies (0.68·10-2kWhgN-NO3-removed-1). The long-term stability of proposed operation was demonstrated during 96days, and the rate of nitrate conversion to N2 even increased to 4.09mgN-NO3 -LNCC -1h-1. A carbon-free operation for a bioelectrochemical system has been developed to treat nitrate-polluted groundwater at a competitive cost, This research was financially supported by the Spanish Government (CTQ2011-23632, CONSOLIDERCSD2007-00055) and the Catalan Government (2014-SGR-1168). Narcis Pous was supported by a project grant from the Catalan Government (2012 FI-B 00941)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

In situ groundwater and sediment bioremediation: Barriers and perspectives at European contaminated sites

  • Majone, Mauro
  • Verdini, Roberta
  • Aulenta, Federico
  • Rossetti, Simona
  • Tandoi, Valter
  • Kalogerakis, Nicolas
  • Agathos, Spiros
  • Puig Broch, Sebastià
  • Zanaroli, Giulio
  • Fava, Fabio
This paper contains a critical examination of the current application of environmental biotechnologies in the field of bioremediation of contaminated groundwater and sediments. Based on analysis of conventional technologies applied in several European Countries and in the US, scientific, technical and administrative barriers and constraints which still need to be overcome for an improved exploitation of bioremediation are discussed. From this general survey, it is evident that in situ bioremediation is a highly promising and cost-effective technology for remediation of contaminated soil, groundwater and sediments. The wide metabolic diversity of microorganisms makes it applicable to an ever-increasing number of contaminants and contamination scenarios. On the other hand, in situ bioremediation is highly knowledge-intensive and its application requires a thorough understanding of the geochemistry, hydrogeology, microbiology and ecology of contaminated soils, groundwater and sediments, under both natural and engineered conditions. Hence, its potential still remains partially unexploited, largely because of a lack of general consensus and public concerns regarding the lack of effectiveness and control, poor reliability, and possible occurrence of side effects, for example accumulation of toxic metabolites and pathogens. Basic, applied and pre-normative research are all needed to overcome these barriers and make in situ bioremediation more reliable, robust and acceptable to the public, as well as economically more competitive. Research efforts should not be restricted to a deeper understanding of relevant microbial reactions, but also include their interactions with the large array of other relevant phenomena, as a function of the truly variable site-specific conditions. There is a need for a further development and application of advanced biomolecular tools for site investigation, as well as of advanced metabolic and kinetic modelling tools. These would allow a quicker evaluation of the bioremediation potential of a site, and in turn a preliminary assessment of the technical feasibility of the chosen bioprocess which could replace or at least reduce the need for time-consuming and expensive field tests. At the same time, field tests will probably remain unavoidable for a detailed design of full scale remedial actions and the above reported tools will in any event be useful for a better design and a more reliable operation, MM, VT, SR, FA and RV acknowledge the European Commission within the Seventh Framework Programme under Grant Agreement No. 265946 (Minotaurus Project, www.minotaurus-project.eu). SP acknowledges the financial support of the Spanish Government (CTQ2011-23632, CONSOLIDERCSD2007-00055)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Removal of microbial indicators from municipal wastewater by a membrane bioreactor (MBR)

  • Martí Serrano, Elisabet
  • Monclús Sales, Hèctor
  • Jofre, Juan
  • Rodríguez-Roda Layret, Ignasi
  • Comas Matas, Joaquim
  • Balcázar, José Luis
The impact of removable and irremovable fouling on the retention of viral and bacterial indicators by the submerged microfiltration membrane in an MBR pilot plant was evaluated. Escherichia coli, sulphite-reducing Clostridium spores, somatic coliphages and F-specific RNA bacteriophages were used as indicators. The membrane demonstrated almost complete removal of E. coli and sulphite-reducing Clostridium spores. However, there was no correlation with membrane fouling. The phage removal varied in accordance with the irremovable fouling, rising from 2.6 to 5.6 log10 units as the irremovable fouling increased (measured by the change in the transmembrane pressure). In contrast, removable fouling did not have any effect on the retention of viruses by the membrane. These results indicate that irremovable membrane fouling may affect the removal efficiency of MBRs and, therefore, their capacity to ensure the required microbiological standards for the permeate achieved, This research was partially funded by the Spanish Ministry of Education and Science and Innovation (CTM2009-14742-C02-01) and (CONSOLIDER-CSD2007-00055)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Biocatalysed sulphate removal in a BES cathode

  • Coma Bech, Marta
  • Puig Broch, Sebastià
  • Pous Rodríguez, Narcís
  • Balaguer i Condom, Maria Dolors
  • Colprim Galceran, Jesús
Sulphate reduction in a biological cathode and physically separated from biological organic matter oxidation has been studied in this paper. The bioelectrochemical system was operated as microbial fuel cell (for bioelectricity production) to microbial electrolysis cell (with applied voltage). Sulphate reduction was not observed without applied voltage and only resulted when the cathodic potential was poised at -0.26 V vs. SHE, with a minimum energy requirement of 0.7 V, while maximum removal occurred at 1.4 V applied. The reduction of sulphate led to sulphide production, which was entrapped in the ionic form thanks to the high biocathode pH (i.e. pH of 10) obtained during the process, This research was financially supported by the Spanish Government (CSD2007-00055, CTQ2011-23632 and IPT-2011-1073-310000)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Coupling anammox and advanced oxidation-based technologies for mature landfill leachate treatment

  • Anfruns Bagaria, Alba
  • Gabarró i Bartual, Jordi
  • González Olmos, Rafael
  • Puig Broch, Sebastià
  • Balaguer i Condom, Maria Dolors
  • Colprim Galceran, Jesús
The aim of this study was to evaluate the suitability to couple anammox process with advanced oxidation processes (AOPs) to treat mature landfill leachate with high nitrogen and non-biodegradable organic matter concentrations (2309±96mgN-TNL-1 and 6200±566mgCODL-1). The combination of a partial nitiration-anammox system coupled with two AOP-based technologies (coagulation/flocculation+ozonation and photo-Fenton) was assessed in terms of nitrogen and carbon removal. Total nitrogen removal efficiency within a range of 87-89% was obtained with both configurations without the need of any external carbon source. The COD removal efficiencies attained were 91% with coagulation/flocculation+ozonation and 98% with photo-Fenton. Applying the biological treatment prior to advanced oxidation processes-based technologies reduced the quantity of needed reagents giving attaining higher removal efficiencies. From a basic economical point of view and taking into account the results of this study, the combination of partial nitritation-anammox system with photo-Fenton treatment was more favorable than with coagulation/flocculation+ozonation treatment, This work was founded by the Spanish Government (CONSOLIDER CSD2007-00055, ITACA, SIRENA CTQ2011-24114 and N-OPTIMMOX IPT-2011-1073-310000). J. Gabarro would like to thank the University of Girona for his predoctoral fellowship (BR 2011). Dr. Gonzalez-Olmos wishes to thank the Ministerio de Ciencia e Innovacion (Spain) for the Juan de la Cierva fellowship (JCI-2010-07104)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Application of a multi-criteria decision model to select of design choices for WWTPs

  • Garrido Baserba, Manel
  • Reif, R.
  • Molino Senante, M.
  • Larrea Urcola, Luis
  • Castillo Llorens, Alba
  • Verdaguer Planas, Marta
  • Poch, Manuel
Stricter regulations in the field of sanitation are driving new dimensions of analysis, in which socioeconomic criteria combined with associated environmental issues are in turn increasing the complexity of wastewater management. In this environment, the development of innovative wastewater treatment technologies provides decision-makers with many efficient alternatives to face these new challenges. This growing number of alternatives inevitably leads, however, to ever greater complexity in the design or upgrade of treatment facilities and demands the acquisition and integration of updated knowledge and well-co-ordinated expertise, encouraging a multi-disciplinary approach. In this paper, it was demonstrated that these requirements have been successfully met in a environmental decision support systems (EDSS). The EDSS was built according to a knowledge-based methodology, whose main objective is the identification and assessment of the most appropriate wastewater treatment technologies for the design of new facilities or the upgrading of obsolete plants. Because removal of nutrients is essential to this approach, this study explores the use of the EDSS to address the selection of biological treatment technologies for different scenarios characterized by wastewater composition (C/N ratio) and other relevant criteria such as environmental and economic factors, population size, discharge in sensitive areas, reuse, cost-benefit analysis, life-cycle analysis, and technical aspects (use of innovative technologies, space availability, reliability, and simplicity of operation), This study has been partially financed by the Spanish Ministry of Education and Science (Consolider Project-NOVEDAR) (CSD2007-00055)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Biogas upgrading: Optimal activated carbon properties for siloxane removal

  • Cabrera-Codony, Alba
  • Montes Morán, Miguel A.
  • Sánchez-Polo, Manuel
  • Martín, María José
  • González Olmos, Rafael
A total of 12 commercial activated carbons (ACs) have been tested for the removal of octamethylcyclotetrasiloxane (D4) in dynamic adsorption experiments using different carrier gases and D4 concentrations. Characterization of the ACs included several physical and chemical techniques. The D4 adsorption capacities were strongly related with the textural development of the ACs. Results showed that the optimum adsorbent for D4 is a wood-based chemically activated carbon, which rendered an adsorption capacity of 1732 ± 93 mg g-1 using 1000 ppm (v/v) of D4 with dry N2 as the carrier gas. When the concentration of D4 was lowered to typical values found in biogas, the adsorption capacity was halved. The presence of major biogas compounds (i.e., CH4 and CO2) and humidity further reduced the D4 adsorption capacity. The polymerization of D4 over the surface of all ACs was found to be relevant after prolonged contact times. The extent of this phenomenon, which may negatively affect the thermal regeneration of the AC, correlated reasonably well with the presence of phenolic and carboxylic groups on the carbon surfaces, This work was funded by the Ministerio de Innovacion y Ciencia (MICINN) (SIRENA CTQ2011-24114 and NOVE-DAR CSD2007-00055). Alba Cabrera-Codony thanks Generalitat de Catalunya DEC for her predoctoral grant (2013F1_B100054). Rafael Gonzalez-Olmos also thanks MICINN for his Juan de la Cierva fellowship (JCI-2010-07104)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Integrated side-stream reactor for biological nutrient removal and minimization of sludge production

  • Coma Bech, Marta
  • Rovira, Salvador
  • Canals, Joan
  • Colprim Galceran, Jesús
Integrated processes to reduce in situ the sludge production in wastewater treatment plants are gaining attention in order to facilitate excess sludge management. In contrast to post-treatments, such as anaerobic digestion which is placed between the activated sludge system and dewatering processes, integrated technologies are placed in the sludge return line. This study evaluates the application of an anoxic side-stream reactor (SSR) which creates a physiological shock and uncouples the biomass metabolism and diverts the activity from assimilation for biosynthesis to non-growth activities. The effect of this system in biological nutrient removal for both nitrogen and phosphorus was evaluated for the anaerobic, anoxic and aerobic reactors. The RedOx potential within the SSR was maintained at - 150 mV while the sludge loading rate was modified by increasing the percentage of recycled activated sludge feed to the SSR (0 and 40% at laboratory scale and 0, 10, 50 and 100% at pilot scale). The use of the SSR presented a slight reduction of phosphorus removal but maintained the effluent quality to the required discharge values. Nitrogen removal efficiency increased from 75 to 86% while reducing the sludge production rate by 18.3%, This research was financially supported by the Spanish Government (CSD2007-00055, CTQ2011-23632, CTQ2011-24114/PPQ, 033/RN08/03.2 and IPT-2011-1073-310000) and OHL Medio Ambiente, INIMA SAU
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Online monitoring of membrane fouling in submerged MBRs

  • Monclús Sales, Hèctor
  • Ferrero, Giuliana
  • Buttiglieri, Gianluigi
  • Comas Matas, Joaquim
  • Rodríguez-Roda Layret, Ignasi
Membrane fouling is the most serious problem affecting membrane bioreactors (MBR). It decreases membrane permeability and consequently increases energy consumption. Various methods and techniques to measure fouling rates (FR) can be found in the literature, but few provide online data, and most are expensive or too invasive. The aim of this short communication is to present a new online method for monitoring and estimating the fouling in an MBR, based on the use of the derivative of the transmembrane pressure (TMP) per cycle, for which hourly and daily mean values can be obtained. This online method (FR per cycle) was experimentally evaluated at a lab-scale MBR plant, where fouling conditions were induced by the addition of a protein (albumin) and a polysaccharide (glucose). Finally, we compared the new method to standard methods, such as the flux-step method. Similar results for fouling rates were found, but the new method showed increased sensitivity. At the same time, the method seems to be useful in characterizing the nature of fouling, This research was funded by the Spanish Ministry of Education and Science (CTM2009-1-14742-C02-01) and (CONSOLIDER-CSD2007-00055)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Minimization of sludge production by a side-stream reactor under anoxic conditions in a pilot plant

  • Coma Bech, Marta
  • Rovira, Salvador
  • Canals, Joan
  • Colprim Galceran, Jesús
This study evaluates the application of an anoxic side-stream reactor in the sludge return line of a conventional activated sludge system for the reduction of biomass production. The oxidation-reduction potential was maintained at -150mV while the applied sludge loading rate was modified by changing the percentage of return sludge treated in this reactor. The observed yield from the conventional system (0.513kg VSSkg-1 COD) was continuously reduced when the portion of return sludge treated was increased. A maximum reduction of 18.3% of the observed yield was obtained treating the whole sludge return line. The sludge age maintained through the experiment. The organic matter removal was not deteriorated, even improved, by the proposed plant modification. Thus, simply applying an anoxic side-stream reactor would decrease the final volume of waste sludge while maintaining the sludge retention time and would, in fact, decrease the economic costs in terms of sludge handling, This research was financially supported by the Spanish Government (CSD2007-00055, CTQ2011-23632, CTQ2011-24114/PPQ, 033/RN08/03.2 and IPT-2011-1073-310000) and GS Inima
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Denitrifying Bacterial Communities Affect Current Production and Nitrous Oxide Accumulation in a Microbial Fuel Cell

  • Vilar Sanz, Ariadna
  • Puig Broch, Sebastià
  • García Lledó, Arantzazu
  • Trias Mansilla, Rosalia
  • Balaguer i Condom, Maria Dolors
  • Colprim Galceran, Jesús
  • Bañeras Vives, Lluís
The biocathodic reduction of nitrate in Microbial Fuel Cells (MFCs) is an alternative to remove nitrogen in low carbon to nitrogen wastewater and relies entirely on microbial activity. In this paper the community composition of denitrifiers in the cathode of a MFC is analysed in relation to added electron acceptors (nitrate and nitrite) and organic matter in the cathode. Nitrate reducers and nitrite reducers were highly affected by the operational conditions and displayed high diversity. The number of retrieved species-level Operational Taxonomic Units (OTUs) for narG, napA, nirS and nirK genes was 11, 10, 31 and 22, respectively. In contrast, nitrous oxide reducers remained virtually unchanged at all conditions. About 90% of the retrieved nosZ sequences grouped in a single OTU with a high similarity with Oligotropha carboxidovorans nosZ gene. nirS-containing denitrifiers were dominant at all conditions and accounted for a significant amount of the total bacterial density. Current production decreased from 15.0 A·m−3 NCC (Net Cathodic Compartment), when nitrate was used as an electron acceptor, to 14.1 A·m−3 NCC in the case of nitrite. Contrarily, nitrous oxide (N2O) accumulation in the MFC was higher when nitrite was used as the main electron acceptor and accounted for 70% of gaseous nitrogen. Relative abundance of nitrite to nitrous oxide reducers, calculated as (qnirS+qnirK)/qnosZ, correlated positively with N2O emissions. Collectively, data indicate that bacteria catalysing the initial denitrification steps in a MFC are highly influenced by main electron acceptors and have a major influence on current production and N2O accumulation, A. V-S. and A. G-L. are recipients of pre-doctoral grants from the Universitat de Girona and the Ministerio de Ciencia y Educacion, respectively. This research was funded through grants from the Spanish Government (CGL2009-08338, CSD2007-00055 and CTQ2011-23632)