Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Pure perovskite BiFeO3–BaTiO3 ceramics prepared by reaction flash sintering of Bi2O3–Fe2O3–BaTiO3 mixed powders

  • Taibi, Ahmed
  • Chaguetmi, Salem
  • Sánchez-Jiménez, Pedro E.
  • Perejón, Antonio
  • García, José Eduardo
  • Satha, Hamid
  • Pérez-Maqueda, Luis A.
In this work, the 0.67BiFeO3-0.33BaTiO3 ferroelectric ceramic was prepared by Reaction Flash Sintering (RFS). This preparation technique combines synthesis and sintering in a single Flash experiment. The starting oxides reacted during the flash to produce a stoichiometric well-sintered solid solution at a temperature of 858 ◦C by applying a modest field of 35 V cm􀀀 1. The process takes place in a matter of seconds, which allows obtaining a pure perovskite structure without secondary phases. X-ray diffraction (XRD) results show the mixture of rhombohedral and pseudocubic phases expected for a composition that lies within a morphotropic phase boundary (MPB) region, since a significant splitting is observed in the reflections at 2θ values of 39◦ and 56.5◦. The microstructure exhibit a peculiar bimodal grain size distribution that determines the electrical properties. As compared with previous results, flash-prepared 0.67BiFeO3-0.33BaTiO3 evidences smaller grain size, as well as slightly lower remanent polarization (Pr) and smaller coercive field (Ec) under similar electric fields. It is also demonstrated that the preparation by RFS provides benefits regarding electrical energy consumption., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Overlooked pitfalls in CaO carbonation kinetics studies nearby equilibrium: Instrumental effects on calculated kinetic rate constants

  • Arcenegui-Troya, Juan
  • Durán-Martín, Jonatan D.
  • Perejón, Antonio
  • Valverde, José M.
  • Pérez-Maqueda, Luis A.
  • Sánchez-Jiménez, Pedro E.
Abstract Due to its technological applications, such as CO2 capture, CaO carbonation kinetics has been extensively studied using a wide array of methods and experimental conditions. A complete understanding of carbonation kinetics is key to optimizing the operating conditions as well as to correctly design the carbonation reactor. However, there is yet no consensus on the reaction model and kinetic parameters that can best describe the CaO carbonation reaction. For instance, the value of the activation energy proposed in different works can vary up to 300%. In this work, we demonstrate that the strong influence of the thermodynamic equilibrium on CaO carbonation kinetics demands careful control of the experimental conditions to obtain meaningful kinetic parameters. Specifically, we explore the influence of three experimental parameters on carbonation kinetics: the gas flow rate, the CO2 partial pressure and the time required to fill the reactor after a gas change. We demonstrate that disregarding these aspects may lead to bogus conclusions on reaction kinetics, which could partly explain the considerable discrepancies found in the literature. The conclusions of this work are not only applicable to the process and experimental setup studied here but also to any study that involves the use of gas flow to drive a reaction, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Steam-enhanced calcium-looping performance of limestone for thermochemical energy storage: The role of particle size

  • Arcenegui-Troya, J.
  • Sánchez-Jiménez, Pedro E.
  • Perejón, Antonio
  • Valverde, José M.
  • Pérez-Maqueda, Luis A.
Steam injection has been proposed to attenuate the decay of CaO reactivity during calcium looping (CaL) under operating conditions compatible with carbon capture and storage. However, it is yet unknown whether the perceived advantages granted by steam hold under the distinct operating conditions required for the integration of the CaL process as a thermochemical energy storage system in Concentrating Solar Power Plants (CaL-CSP). Here, we study the influence of steam in conditions compatible with a CaL-CSP scheme and assess its impact when injected only during one stage; either calcination or carbonation, and also when it is present throughout the entire loop. The results presented here demonstrate that steam boosts the CaO multicycle performance in a CO2 closed loop to attain residual conversion values similar to those achieved at moderate temperatures under inert gas. Moreover, it is found that the enhancement in multicycle activity is more pronounced for larger particles., This work has been supported by the Spanish Government Agency Ministerio de Economía y Competitividad-FEDER (contracts CTQ2017- 83602-C2-1-R and -2-R) and Junta de Andalucía and Universidad de Sevilla (Programa Operativo FEDER Andalucía 2014–2020, projects P18-FR-1087 and US-1262507). We acknowledge the funding received by the European Union's Horizon 2020 research and innovation programme under grant agreement No. 727348, project SOCRATCES. Financial support received from Junta de Andalucía-Consejería de Economía, Conocimiento, Empresas y Universidad via a postdoctoral fellowship with reference DOC_00044 is also acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Albero: An alternative natural material for solar energy storage by the calcium-looping process

  • Moreno, Virginia
  • Arcenegui-Troya, J.
  • Sánchez-Jiménez, Pedro E.
  • Perejón, Antonio
  • Chacartegui, Ricardo
  • Valverde, José Manuel
  • Pérez-Maqueda, Luis A.
Large-scale thermochemical energy storage (TCES) is gaining relevance as an alternative to current thermal energy storage systems in Concentrated Solar Power plants. Among the different systems, the reversible reaction between CaO and CO2 stands out due to the wide availability and low cost of the raw material: limestone. Direct solar absorption of the storage media would improve the efficiency of solar-to-thermal energy storage due to reduced thermal transfer barriers, but the solar optical absorption of CaCO3 is poor. In this work, we propose the use of a Ca-rich calcarenite sedimentary rock so-called albero as an alternative to limestone. We demonstrate that this reddish material exhibits an average solar absorptance that is approximately ten times larger than limestone. Moreover, the multicycle carbonation/calcination performance under different experimental conditions has been studied by thermogravimetry, and similar values to those exhibited for limestone have been obtained. Besides, the material is cheap (6 €/ton), and simulations showed that the use of this material would significantly improve the overall CaL-CSP efficiency at the industrial level., This work has been funded by the grants CTQ2017-83602-C2-1-R and -2-R (MCIN/AEI/ 10.13039/501100011033 and ERDF A way of making Europe by the European Union), and grant PDC2021-121552-C21 (MCIN/AEI/10.13039/501100011033 and European Union Next Generation EU/PRTR). Financial support from projects P18-FR-1087 and US-1262507 (Junta de Andalucía-Consejería de Conocimiento, Investigación y Universidad-Fondo Europeo de Desarrollo Regional, Programa Operativo FEDER Andalucía 2014–2020) and INTRAMURALCSIC grant numbers 201960E092 and 202060I004 is acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Influence of AC fields and electrical conduction mechanisms on the flash-onset temperature: Electronic (BiFeO3) vs. ionic conductors (8YSZ)

  • Molina-Molina, Sandra
  • Perejón, Antonio
  • Pérez-Maqueda, Luis A.
  • Sánchez-Jiménez, Pedro E.
This work aims to clarify the influence of AC (up to 50 kHz) vs DC fields on the flash-onset temperature, emphasizing the role of the electrical conduction mechanism. BiFeO3 (BFO) is used as an example of electronic conductor while 8-mol % Yttria-stabilized zirconia (8YSZ) is used as an example of ionic conductor. For 8YSZ, a frequency dependence of the flash-onset temperature and flash-induced heating is observed. This is consistent with the different contributions found in the total electrical response of 8YSZ as characterized by impedance spectroscopy measurements. Estimations based on the blackbody radiation model suggest that 8YSZ samples attain higher temperatures under AC fields due to a more efficient heating. Moreover, a noticeable decrease in the activation energy for the electrical conduction after the flash is triggered is attributed to electronic conduction. Meanwhile, the lack of frequency response and insensitiveness to the type of electrical field found in the case of BFO can be attributed to its mainly electronic bulk conduction., This work has been funded by the grants CTQ2017-83602-C2-1-R (MCIN/AEI/10.13039/501100011033 and ERDF A way of making Europe by the European Union), projects P18-FR-1087 and US-1262507 (Junta de Andalucía-Consejería de Conocimiento, Investigación y Universidad – Fondo Europeo de Desarrollo Regional (FEDER) (Programa Operativo FEDER Andalucía 2014–2020) and INTRAMURAL-CSIC grant numbers 201960E092 and 202060I004., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Thermochemical energy storage using calcium magnesium acetates under low CO2 pressure conditions

  • Amghar, Nabil
  • Sánchez-Jiménez, Pedro E.
  • Pérez-Maqueda, Luis A.
  • Perejón, Antonio
The calcium looping multicycle performance of CaO-based materials, derived from calcium magnesium acetates with different Mg content were tested under experimental conditions compatible with thermochemical energy storage. In order to reduce the sintering-induced decay in performance, calcination at an absolute CO2 pressure of 0.1 bar and 0.01 bar is implemented. CaO carbonation is performed at standard 1 bar CO2 conditions. The samples can be fully calcined in short residence times. Samples with MgO present high cycling stability, even when the MgO content is as low as 5 mol%. The effective conversion values lie within the range 0.88–0.84 over ten calcination/carbonation cycles, which provides an accumulated energy storage density of 90.9 GJ/m3. This outstanding reactivity is related with the microstructure of the sample after calcination composed of CaO nanoparticles that are highly reactive for carbonation., This work has been funded by EU Next Generation funds and Spanish Ministry of Science and Innovation (projects TED2021-131839B-C22 and PDC2021-121552-C21), and by the grant CTQ2017-83602-C2-1-R (MCIN/AEI/10.13039/501100011033 and ERDF A way of making Europe by the European Union)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Low Temperature Magnetic Transition of BiFeO3 Ceramics Sintered by Electric Field-Assisted Methods: Flash and Spark Plasma Sintering

  • Manchón-Gordón, Alejandro F.
  • Perejón, Antonio
  • Gil-González, Eva
  • Kowalczyk, M.
  • Sánchez-Jiménez, Pedro E.
  • Pérez-Maqueda, Luis A.
Low temperature magnetic properties of BiFeO3 powders sintered by flash and spark plasma sintering were studied. An anomaly observed in the magnetic measurements at 250 K proves the clear existence of a phase transition. This transformation, which becomes less well-defined as the grain sizes are reduced to nanometer scale, was described with regard to a magneto-elastic coupling. Furthermore, the samples exhibited enhanced ferromagnetic properties as compared with those of a pellet prepared by the conventional solid-state technique, with both a higher coercivity field and remnant magnetization, reaching a maximum value of 1.17 kOe and 8.5 10-3 emu/g, respectively, for the specimen sintered by flash sintering, which possesses the smallest grains. The specimens also show more significant exchange bias, from 22 to 177 Oe for the specimen prepared by the solid-state method and flash sintering technique, respectively. The observed increase in this parameter is explained in terms of a stronger exchange interaction between ferromagnetic and antiferromagnetic grains in the case of the pellet sintered by flash sintering., This work has been funded by the grant CTQ2017-83602-C2-1-R (MCIN/AEI/10.13039/ 501100011033 and ERDF A way of making Europe by the European Union), projects P18-FR-1087 (Junta de Andalucía-Consejería de Conocimiento, Investigación y Universidad-Fondo Europeo de Desarrollo Regional Programa Operativo FEDER Andalucía 2014–2020) and INTRAMURAL-CSIC grant number 201960E092. A.F. Manchón-Gordón also acknowledge Grant FJC2021-047783-I funded by MCIN/AEI/10.13039/501100011033 and by “European Union NextGenerationEU/PRTR”, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Determination of the activation energy under isothermal conditions: revisited

  • Arcenegui-Troya, Juan
  • Sánchez-Jiménez, Pedro E.
  • Perejón, Antonio
  • Pérez-Maqueda, Luis A.
The kinetic analysis of solid-state processes aims at obtaining fundamental information that can be used for predicting the time evolution of a process within a wide range of conditions. It is an extended belief that the determination of the kinetic parameters from the analysis of curves recorded under isothermal conditions is strongly conditioned by the kinetic model used to fit the experimental data. Thus, much effort is devoted to finding the model that truly describes a process in order to calculate the kinetic parameters with accuracy. In this work, we demonstrate that the value of activation energy determined from kinetic analysis of isothermal curves is independent of the kinetic model used to fit the experimental data and, taking advantage of the underlying reason for this, a method for determining the activation energy with two isothermal curves is proposed., This work has been funded by the grant CTQ2017-83602-C2-1-R (MCIN/AEI/https://doi.org/10.13039/501100011033 and ERDF A way of making Europe by the European Union), grant PDC2021-121552-C21 (MCIN/AEI/https://doi.org/10.13039/501100011033 and European Union Next GenerationEU/PRTR), projects P18-FR-1087 and US-1262507 (Junta de Andalucía-Consejería de Conocimiento, Investigación y Universidad-Fondo Europeo de Desarrollo Regional (FEDER) (Programa Operativo FEDER Andalucía 2014–2020) and INTRAMURAL-CSIC grant numbers 201960E092 and 202060I004. JAT acknowledges financial support received from Junta de Andalucı́a-Consejerı́a de Economı́a, Conocimiento, Empresas y Universidad via a postdoctoral fellowship with reference DOC_00044., Peer reviewed