Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental and numerical study of lift-off length and ignition delay of a two-component diesel surrogate

  • Payri, Raul|||0000-0001-7428-5510
  • Viera Sotillo, Juan Pablo
  • Pei, Yuanjiang
  • Som, Sibendu
Understanding and controlling mixing and combustion processes is fundamental for the ever more demanding pollutant regulations and fuel consumption standards of direct injection diesel engines. The fundamentals of these processes have been long studied from both experimental and numerical perspectives. As numerical models become more advanced, the need for adequate experimental data increases. Hence, experimental methodologies and scientific databases need to be enhanced with more quantitative, accurate, consistent, and reliable information in order to evaluate the models in a robust fashion. The present study seeks to enhance the current state-of-the-art by further evaluating the combustion performance of a two-component diesel surrogate for multi-dimensional compression ignition engine simulations, composed of n-dodecane and m-xylene. This surrogate is expected to better represent diesel fuel combustion than the standard Engine Combustion Network (ECN) fuel (n-dodecane), since it contains an alkyl-benzene which represents an important chemical class present in diesel fuels. Experiments and numerical simulations have been performed on lift-off length and ignition delay in a wide range of conditions for a single-hole injector from ECN. The experiments were carried out in a constant-pressure flow facility able of reproducing engine-like thermodynamic conditions. The experiments focused in characterizing the ignition delay through the Schlieren technique, and the lift-off length through OH* chemiluminescence visualization, at ECN suggested test conditions. On the other hand, computational fluid dynamics (CFD) simulations were performed using a multi-flamelet representative interactive flamelet (mRIF) model by taking consideration of turbulence-chemistry-interaction (TCI) with a beta-function on the form of scalar probability density functions (PDFs). This model is evaluated extensively over a wider range of parametric variations in this study. Encouraging results were obtained compared to the experiments with regards to the predictions of ignition delay and lift-off length at different ambient temperatures, ambient densities and fuel-injection pressures. Under predictions were found at less reactive conditions, which leave room for improvement in the future. (C) 2014 Elsevier Ltd. All rights reserved., The research was funded by DOE's Office of Vehicle Technologies, Office of Energy Efficiency and Renewable Energy under Contract No. DE-AC02-06CH11357. The authors wish to thank Gurpreet Singh and Leo Breton, program managers at DOE, for his support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A Note on Bubble Sizes in Subcooled Flow Boiling at Low Velocities in Internal Combustion Engine-Like Conditions

  • Torregrosa, A. J.|||0000-0003-0933-1626
  • Broatch, A.|||0000-0001-9991-1039
  • Olmeda, P.|||0000-0002-3161-0165
  • Cornejo-Luna, Omar
[EN] Current trends in engine design indicate the necessity to take advantage of the highest rates of heat transfer associated with nucleate boiling, mostly at high engine loads. When used in conjunction with advanced thermal management strategies, subcooled boiling may take place at very low velocities, for which little information is available, and in ducts with small cross-sectional area, so that undesired effects of the relative sizes of ducts and bubbles may appear. In this paper, experiments on subcooled boiling flow at low velocities and engine-like temperature conditions were conducted with a usual engine coolant. A high-speed photographic camera was used to collect images of the detached vapor bubbles, and the microscopic characteristics of the heating surface were determined. Experimental results for the mean values show acceptable agreement with the results of a mechanistic radius model, when assuming that departure and lift-of radius are related through the flow boiling suppression factor. Additionally, the results obtained are compatible with the sizes of the nucleation sites estimated from the surface characterization. The results obtained for the size distribution are consistent with those found in the literature., The equipment used in this work has been partially supported by FEDER project funds “Dotacion de infraestructuras científico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06)”, framed in the operational program of unique scientific and technical infrastructure of the Ministry of Science and Innovation of Spain. O. Cornejo is indebted to Senacyt Panama for their support. The authors wish to thank Dr. D. Busquets and Dr. E. Rayon their kind cooperation in the surface ´ characterization and in the interpretation of its results.