Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Buckling Analysis and Stability of Compressed Low-Carbon Steel Rods in the Elastoplastic Region of Materials

  • Partskhaladze, G.
  • Mshvenieradze, I.
  • Medzmariashvili, E.
  • Chavleshvili, G.
  • Yepes, V.|||0000-0001-5488-6001
  • Alcalá-González, Julián|||0000-0003-1376-8441
[EN] This paper presents new approaches for solving a problem of the stability of compressed rods in the elastoplastic working region of materials. It is known that the columns of buildings, supports of engineering devices, drill rods of oil, and gas extraction industry may be subjected to significant risk of stability loss. Nowadays, there are design methods based on test results defining the relations (e.g., critical stresses-slenderness) to avoid this risk due to stability loss, but the precision and limits of definition are not always known. The main objectives of the study were to develop new approaches that would allow specifying the values of critical stresses of compressed elements beyond the proportional limit. The problem of stability of the compressed elements in the elastoplastic region was studied according to the stability theory. The authors suggested an original approach to the issue; in particular, the determination of values of the critical stresses and the finding of the points of the bifurcation were carried out by the tangent established by experimental results and by the approximation of the so-called double modulus. Comparative analysis showed the advantage of the proposed approach, particularly that the new critical curves were located below the curves of Engesser-Karman and Shanley and above the critical curves established by building codes. A new approach for the determination of critical stresses in the elastoplastic region was developed through which the structural reliability and economic efficiency was increased by almost 12% compared to the existing approaches., This research was financially supported by the Erasmus Mundus Action 2 Project Electra: Enhancing Learning in ENPI Countries through Clean Technologies and Research related Activities (project: ELEC1400294) and the Spanish Ministry of Economy and Competitiveness, along with FEDER funding (project: BIA2017-85098-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Heuristic Optimization of a New Type of Prestressed Arched Truss

  • Partskhaladze, Gaioz
  • Medzmariashvili, Elguja
  • Chavleshvili, Gocha
  • Surguladze, Bichiko
  • Alcalá-González, Julián|||0000-0003-1376-8441
  • Yepes, V.|||0000-0001-5488-6001
[EN] This paper represents new approaches for calculating, designing, and optimizing prestressed arched trusses with a tie member. Structural systems with long spans, such as trusses, beams, frames, etc., are subjected to a considerable/substantial risk of losing load-carrying capacity because of the different types of loads used. Some traditional design methods define the values of prestressing force in the tie member and internal forces in the truss elements to avoid this load capacity loss. However, the accuracy and limits of the determination of the forces are not necessarily known. The authors offer a new type of prestressed arched truss and some new approaches in the design and calculation process to solve these disadvantages. The study¿s main objectives were to design an innovative and new geometric form of prestressed arched truss, which allows the development of high-value prestressing force, to optimize a new truss for reducing self-weight, increasing load-carrying capacity compared to its analogs. The force, stiffness matrix, and simulated annealing methods were used during the study. A new advance to the optimization of prestressed arched truss suggested by the authors reduces the self-weight and improves the load capacity of the truss by 8¿17%, depending on the span., This research was funded by the Erasmus Mundus Action 2 Project Electra: Enhancing Learning in ENPI Countries through Clean Technologies and Research related Activities (project: ELEC1400294), Erasmus+ program InnoCENS-Enhancing innovation competences and entrepreneurial skills in engineering education (project: 573965-EPP-1-2016-1-SE-EPPKA2-CBHE-JP). Grant PID2020-117056RB-I00 funded by MCIN/AEI/ 10.13039/501100011033 and by ERDF A way of making Europe.