Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 25
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Evaluation of manganese minerals for chemical looping combustion

  • Mei, Daofeng
  • Mendiara, Teresa
  • Abad Secades, Alberto
  • Diego Poza, Luis F. de
  • García Labiano, Francisco
  • Gayán Sanz, Pilar
  • Adánez Elorza, Juan
  • Zhao, Haibo
The use of mineral materials as oxygen carriers for Chemical Looping Combustion (CLC) is an attractive option due to their low cost. This paper reports an experimental study of four manganese minerals as potential oxygen carriers focusing on the behavior in CLC as well as in Chemical Looping with Oxygen Uncoupling (CLOU). Experiments were carried out in a thermogravimetric apparatus (TGA) and a fluidized-bed reactor. Repeated tests with all the minerals showed no sufficient CLOU properties. Then, they can only be used in CLC applications involving the redox pairs Mn3O4/MnO and Fe2O3/Fe3O4. Oxygen transport capacity and reactivity to the main fuel gases (H2, CO, and CH4) were determined in a TGA. Manganese minerals were also tested during 35–54 h in a fluidized-bed reactor to evaluate the evolution of reactivity to H2, CO, and CH4 as well as their attrition rate and mechanical strength. The reactivity of the materials decreased in the first 10 cycles with CH4 and then became quite stable for the rest of the cycles performed with CH4, CO, and H2. In comparison to previously tested Fe-based minerals, lower reactivity with CH4 was found for the manganese minerals. However, in terms of CO and H2 combustion, their reactivity was adequately high. During the tests, agglomeration and defluidization were never found for any material. Mechanical crushing strength of the particles decreased with cycles, which led to the increase of attrition rate of some materials above acceptable levels. Nevertheless, materials with adequate crushing strength and low attrition were identified. Combining the reactivity and attrition resistance, the manganese minerals MnSA and MnGBHNE from South Africa and Gabon, respectively, can be suggested as promising materials for CLC with coal., This work was supported by the Spanish Ministry of Economy and Competitiveness (project ENE 2013-45454-R), by the European Regional Development Fund (ERDF), by the CSIC (project 2014-80E101) and by the Government of Aragón (Spain, Ref. T06). T. Mendiara thanks for the ‘‘Ramón y Cajal’’ post-doctoral contract awarded by the Spanish Ministry of Economy and Competitiveness. D. Mei is grateful for the support provided by the China Scholarship Council (CSC201306160054). The authors also thank Hidro Nitro Española S.A. for providing MnSA and MnGBHNE materials and Leopoldo Alcázar (CT-GAS) for providing the MnBR material., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Manganese minerals as oxygen carriers for chemical looping combustion of coal

  • Mei, Daofeng
  • Mendiara, Teresa
  • Abad Secades, Alberto
  • Diego Poza, Luis F. de
  • García Labiano, Francisco
  • Gayán Sanz, Pilar
  • Adánez Elorza, Juan
  • Zhao, Haibo
In this paper, four different manganese minerals were tested in a batch fluidized bed reactor to evaluate their performance in the chemical looping combustion (CLC) of solid fuels. The char gasification rate in the experiments with the manganese minerals tested was higher than the corresponding values for ilmenite and iron ore, which were taken as benchmark materials. This phenomenon was attributed to the deposition of K, Na, and Ca from the manganese minerals on char particles so that they catalyzed char gasification. The char gasification rate observed using manganese minerals decreased with the number of cycles until a stable value was reached. Under these conditions, one of the materials presented higher char gasification rates than those observed for benchmark materials even when most of the K was already released. An estimation of the CO2 capture efficiency in a continuous unit using one of the selected manganese minerals showed that around 99% CO2 capture efficiency could be reached at 1000 °C with a solid inventory in the fuel reactor as low as 300 kg/MWth if an efficient carbon stripper was present., This work was supported by the Spanish Ministry of Economy and Competitiveness (project ENE 2013-45454-R) and by the European Regional Development Fund (ERDF), by the CSIC (project 2014-80E101). T. Mendiara thanks for the ‘‘Ramón y Cajal’’ post doctoral contract awarded by the Spanish Ministry of Economy and Competitiveness. D. Mei is grateful for the support provided by the China Scholarship Council (CSC201306160054). The authors also thank Hidro Nitro Española S.A. for providing MnSA and MnGBHNE materials and Leopoldo Alcázar (CT-GAS) for providing the MnBR material., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Design and operation of a 50 kWth chemical looping combustion (CLC) unit for solid fuels

  • Abad Secades, Alberto
  • Pérez-Vega, Raúl
  • Diego Poza, Luis F. de
  • García Labiano, Francisco
  • Gayán Sanz, Pilar
  • Adánez Elorza, Juan
A Chemical Looping Combustion (CLC) unit for solid fuels has been designed, erected and operated. The design was based on a thermal power of 20 kWth for in-situ Gasification Chemical Looping Combustion (iG-CLC) or 50 kWth for Chemical Looping with Oxygen Uncoupling (CLOU). Fuel and air reactors are two interconnected circulating fluidized beds reactors, with the coal being fed at the bottom of the fuel reactor to maximize the contact between the volatile matter and the oxygen carrier particles. A carbon stripper has been included between fuel and air reactors to increase the CO2 capture rates. In this unit, the char particles are separated from the oxygen carrier particles and recirculated to the fuel reactor. The solids flow exiting from the fuel reactor is split into two different streams by using a double loop seal down the fuel reactor cyclone. One goes to the carbon stripper and the other is recirculated to the fuel reactor. In this way it is possible to have an independent control of solids inventory in the fuel reactor and the global solid circulation flow rate between fuel and air reactors. First operational results at steady state have been obtained with stable operation in iG-CLC mode during combustion of a bituminous coal with ilmenite being the oxygen carrier. A CO2 capture value of 88% at 991 ºC and a total oxygen demand value of 8.5% were obtained with a solids inventory in the fuel reactor of 470 kg/MWth., This work was supported by the Spanish Ministry for Science and Innovation (Project ENE2013-45454-R). R. Pérez-Vega thanks for the FPI Fellowship., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Conceptual design of a 100 MWth CLC unit for solid fuel combustion

  • Abad Secades, Alberto
  • Adánez Elorza, Juan
  • Gayán Sanz, Pilar
  • Diego Poza, Luis F. de
  • García Labiano, Francisco
  • Sprachmann, Gerald
The conceptual design of a 100 MWth unit for coal combustion with CO2 capture by in-situ Gasification Chemical Looping Combustion (iG-CLC) was done. Ilmenite was considered the oxygen carrier and a highly reactive sub-bituminous coal was the fuel. The main components of the iG-CLC unit were a fuel reactor, a carbon stripper and an air reactor. Mass and enthalpy balances were performed to determine the solids circulation flow rate, temperature of the reactors, steam and air requirements, and heat duty of heat exchangers. Fluid dynamics considerations and cyclones sizes were taken into account for the conceptual design and the dimensioning of these devices. In addition, optimized operating conditions obtained with a mathematical model were considered in the design procedure. Then, the performance of the iG-CLC unit was estimated with the model. Some benefits were identified when recirculated CO2 was used to fluidize the carbon stripper and fuel reactor, regarding both fuel reactor performance and energy integration of the iG-CLC system. Thus, a CO2 capture value of 95% with a carbon stripper with 98% efficiency and an oxygen demand in exit gases from the fuel reactor of 7% was predicted with a solids inventory in the fuel reactor of 750 kg/MWth. Moreover, the energy penalty related to steam generation was minimized when H2O was replaced by CO2. Results presented in this work can be used to estimate the net efficiency of the plant in future works., This work was partially supported by the Spanish Ministry for Science and Innovation (MICINN project ENE2011-26354 and ENE2013-45454-R), the European Regional Development Fund (ERDF), and by Shell Global Solutions International BV (Contract PT26961)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Sulphur, nitrogen and mercury emissions from coal combustion with CO2 capture in chemical looping with oxygen uncoupling (CLOU)

  • Pérez-Vega, Raúl
  • Adánez-Rubio, Iñaki
  • Gayán Sanz, Pilar
  • Izquierdo Pantoja, María Teresa
  • Abad Secades, Alberto
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
  • Adánez Elorza, Juan
© 2016. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Chemical looping with oxygen uncoupling (CLOU) is a chemical looping combustion (CLC) process for the combustion of solid fuels with the use of a solid oxygen carrier that releases gaseous oxygen inside the fuel reactor. The aim of this work was to study the fate of pollutant elements present in fuel, i.e. S, N and Hg, during CLOU combustion. Experiments using lignite as fuel were carried out in a 1.5 kWth unit operating continuously for more than 35 h of coal combustion. Novel particles containing 50 wt.% CuO, 10 wt.% Fe2O3 and 40 wt.% MgAl2O4 prepared by spray drying were used as the oxygen carriers in the CLOU process. Most of the sulphur introduced with the fuel exited as SO2 at the fuel reactor outlet, although a small amount of SO2 was measured at the air reactor outlet. Most of the nitrogen present in coal was found as N2 at the outlet of the fuel reactor, although 20 wt.% of N in the coal was converted to NO. Mercury speciation was also analyzed. The major mercury species in the fuel reactor was Hg0 (g), and the Hg0 (g)/Hgtotal (g) ratio in the air reactor was 0.5., This work was partially supported by the European Commission, under the RFCS program (ACCLAIM Project, Contract RFCP-CT-2012-00006), ALSTOM Power Boilers (France), the Spanish Ministry of Economy and Competitiveness (ENE2013-45454-R), and the European Regional Development Fund (ERDF). Raul Pérez-Vega thanks to Spanish Ministry of Economy and Competitiveness for the FPI fellowship., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Use of hopcalite derived Cu-Mn mixed oxide as oxygen carrier for Chemical Looping with Oxygen Uncoupling Process

  • Adánez-Rubio, Iñaki
  • Abad Secades, Alberto
  • Gayán Sanz, Pilar
  • Adánez, Imanol
  • Diego Poza, Luis F. de
  • García Labiano, Francisco
  • Adánez Elorza, Juan
Chemical-Looping with Oxygen Uncoupling (CLOU) is an alternative Chemical Looping process for the combustion of solid fuels with inherent CO2 capture. The CLOU process needs a material as oxygen carrier with the ability to give gaseous O2 at suitable temperatures for solid fuel combustion, e.g. copper oxide and manganese oxide. In this work, treated commercial Carulite 300® was evaluated as oxygen carrier for CLOU. Carulite 300® is a hopcalite material composed of 29.2 wt.% CuO and 67.4 wt.% Mn2O3. Oxygen release rate and the fluidization behavior, regarding agglomeration and attrition rate, were analyzed in a TGA and in a batch fluidized bed respectively. Experiments in a batch fluidized bed reactor were carried out at temperatures ranging from 800 to 930 ºC with a medium volatile bituminous coal from South Africa and its char as fuels. The hopcalite derived oxygen carrier showed high O2 release rate, no unburnt products at low oxygen carrier to fuel mass ratios and very high oxygen transference rate by gas-solid reaction. This material has the capacity to generate gaseous oxygen at lower temperatures than Cu-based oxygen carriers, which suggest this material is suitable to work at lower temperatures in the fuel reactor without the presence of unburnt products; however its low mechanical resistance after redox cycles makes necessary an improvement of its physical properties for being use as an oxygen carrier., This work was partially supported by the Spanish Ministry of Economy and Competitiveness (MINECO Project: ENE2013-45454-R) and the European Union FEDER funds., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

On the attrition evaluation of oxygen carriers in Chemical Looping Combustion

  • Cabello Flores, Arturo
  • Gayán Sanz, Pilar
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
  • Abad Secades, Alberto
  • Adánez Elorza, Juan
© 2016. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Chemical Looping Combustion (CLC) is one of the most promising processes for the low-cost capture of CO2. It is based on the transfer of oxygen from air to the fuel by means of a solid oxygen carrier that circulates between two interconnected fluidized bed reactors: the fuel reactor and the air reactor. CO2 capture is inherent to this process since air does not become mixed with the fuel. A key issue for the large-scale development of CLC technology is the selection of oxygen carrier materials with suitable properties such as high reactivity and good fluidization. Another important feature that an oxygen carrier must fulfil is to have high resistance to attrition. For this purpose, several particle characteristics related to attrition resistance were analysed in this work on 23 oxygen carriers, both natural and synthetic, prepared by different methods and using different metal oxides. Particle crushing strength and Air Jet Index (AJI) were determined for the fresh materials, as well as the attrition rate and the corresponding particle lifetime during multi-cycle redox reactions in a continuously operated CLC unit for gaseous fuels. A comparison was made of the different methods used to evaluate attrition behaviour. The AJI-ASTM test for particles subjected to long-term CLC operation was used as a standard screening tool to evaluate the attrition behaviour of the oxygen carriers. Finally, a methodology was proposed for the selection of oxygen carriers as eligible materials for CLC scale-up based on attrition behaviour., The work presented in this article was partially funded by the Spanish Ministry of Economy and Competitiveness (ENE2013-45454-R), by the European Commission Seventh Framework Programme under grant agreement No. 608571 (Project acronym SUCCESS) and by the European Regional Development Fund (ERDF). A. Abad and A. Cabello thank CSIC for the financial support given to project 201480E101. ICB-CSIC also thanks Johnson Matthey for the preparation of some of the oxygen carriers tested in this work., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Coal combustion in a 50 kWth Chemical Looping Combustion unit: seeking operating conditions to maximize CO2 capture and combustion efficiency

  • Pérez-Vega, Raúl
  • Abad Secades, Alberto
  • García Labiano, Francisco
  • Gayán Sanz, Pilar
  • Diego Poza, Luis F. de
  • Adánez Elorza, Juan
© 2016. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, In-situ Gasification Chemical-Looping Combustion (iG-CLC) with coal has been proposed as a low-cost process for the capture of CO2 during the energy generation. Previous experimental works have highlighted that high CO2 capture efficiency, close to 100%, can be achieved. However, a certain amount of unburnt gases (mainly CH4, CO and H2) are present in the CO2 stream. These gases can be treated in an oxygen polishing step placed downstream from the CLC unit where they are burnt with pure oxygen, which defines the so-called oxygen demand for the process. The aim of this work was to optimize the performance of the iG-CLC process with coal in order to minimize oxygen demand while maintaining CO2 capture at high levels. Ilmenite was used as the oxygen carrier to burn a bituminous coal in a 50 kWth CLC unit, which consisted of a fuel reactor, an air reactor and a carbon stripper unit between them. The fuel reactor temperature, solids inventory in the fuel reactor, solids circulation rate, coal feeding rate and carbon stripper efficiency were varied, and the CO2 capture efficiency and oxygen demand were calculated for each set of operating conditions. The effect of the fuel reactor temperature was higher on the CO2 capture than on the oxygen demand, with a temperature close to 1000 °C advisable in order to reach CO2 capture rates higher than 90%. In order to further increase CO2 capture, the efficiency of char separation in the carbon stripper was increased. The solids circulation flow rate and the coal feeding rate -which define the oxygen carrier-to-fuel ratio-, in addition to the solids inventory in the fuel reactor, showed a strong influence on the combustion efficiency. Thus, the total oxygen demand was able to be decreased from 10% to 7% by increasing the oxygen carrier-to-fuel ratio from 1.1 to 1.5 and the solids inventory from 450 to 720 kg/MWth. However, an increase in the circulation rate showed a detrimental effect on CO2 capture, which could be offset by increasing the carbon stripper efficiency., This work was supported by the Spanish Ministry for Economy and Competitiveness via the ENE2013-45454-R project and the European Regional Development Fund (ERDF). Raúl Pérez-Vega thanks MICINN for the FPI Fellowship., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Coal combustion with a spray granulated Cu-Mn mixed oxide for the Chemical Looping Oxygen Uncoupling (CLOU) process

  • Adánez-Rubio, Iñaki
  • Abad Secades, Alberto
  • Gayán Sanz, Pilar
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
  • Adánez Elorza, Juan
© 2017. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, The Chemical Looping with Oxygen Uncoupling (CLOU) process is a form of Chemical Looping Combustion (CLC) technology that enables the combustion of solid fuels by means of oxygen carriers that release gaseous oxygen in the fuel reactor, i.e. with oxygen uncoupling capability. In recent years, tests have found several Cu-based, Mn-based and mixed oxide oxygen carriers with suitable properties for the CLOU process. Among them, Cu-Mn mixed oxides show high reactivity and high O2 equilibrium concentration at temperatures of interest for coal combustion. In this work, proof of concept was demonstrated by burning coal with Cu-Mn mixed oxides in a 1.5 kWth CLOU unit for the first time. The effect of fuel reactor temperature, solids circulation flow, fluidization agent in the fuel reactor (inert N2 or steam as gasifying agent), and excess air in the air reactor on combustion efficiency and CO2 capture rate was analysed. The results showed that high combustion efficiency and CO2 capture are feasible using this material at relatively low fuel reactor operating temperatures. Therefore, the developed Cu-Mn mixed oxide was a suitable material for use as an oxygen carrier for the CLOU combustion of solid fuels. Optimum operating conditions were determined for this oxygen carrier with regard to the oxygen circulation rate and air reactor conditions for the regeneration of the oxygen carrier., This work was supported by the Spanish Ministry of Economy, Industry and Competitiveness (MINECO Project: ENE2013-45454-R, ENE2014-56857-R and ENE2016-77982-R) and the European Union FEDER funds. Our thanks to Ing. Konrad Holscher from Mina Invierno Chile, for supplying the subbituminous coal., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

In situ gasification Chemical-Looping Combustion of coal using limestone as oxygen carrier precursor and sulphur sorbent

  • Abad Secades, Alberto
  • Obras-Loscertales, Margarita de las
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
  • Gayán Sanz, Pilar
  • Adánez Elorza, Juan
© 2017. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, In-situ Gasification Chemical-Looping Combustion (iG-CLC) burning coal is achieving a great interest due to the possibility of using low cost oxygen carriers such as CaSO4. The Limestone Chemical Looping Combustion process (LCL-CTM) registered by Alstom Power Inc. proposes the use of a continuous CaCO3 feeding together with coal to produce CaSO4 as an oxygen carrier via sulphur retention. The operation is similar to what happens in a circulating fluidized bed boiler burning coal. In the present research work, the study of thermodynamic equilibrium limitations together with mass and enthalpy balances have been carried out for a CLC system in order to investigate whether the LCL-CTM process is a promising and energy efficient option to carry out the coal combustion with CO2 capture and in-situ desulphurisation. So, no limitations were found to transfer the required oxygen from air to fuel using sulphated limestone as oxygen carrier for whatever coal used. However, coals with sulphur content above 1 wt.% are advisable to perform this process. In addition, no drawback referred to thermal integration in the system has been detected. Thus, operation at 950 ºC in the fuel reactor to avoid SO2 release via side reactions, and 1000 ºC in the air reactor is feasible. Likewise, experimental tests have been performed in a thermogravimetric analyser to analyse the capability of a limestone to be sulphated and to transfer oxygen. A value of the oxygen transport capacity of about 16.7 wt.% was obtained. This value is four times higher than that of others typical inexpensive oxygen carriers published in literature., The work presented in this article is partially funded by the Spanish Ministry of Economy and Competitiveness (ENE 2014-56857-R, ENE2013-45454-R) and by the European Regional Development Fund (ERDF). A. Abad thanks CSIC for the financial support given to the project 201480E101., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Titanium substituted manganese-ferrite as an oxygen carrier with permanent magnetic properties for chemical looping combustion of solid fuels

  • Abián, María
  • Abad Secades, Alberto
  • Izquierdo Pantoja, María Teresa
  • Gayán Sanz, Pilar
  • Diego Poza, Luis F. de
  • García Labiano, Francisco
  • Adánez Elorza, Juan
© 2017. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Mixed oxides of Mn-Fe have been identified as suitable materials for Chemical Looping Combustion (CLC) with solid fuels both via in-situ Gasification Chemical Looping Combustion (iG-CLC) and Chemical Looping with Oxygen Uncoupling (CLOU) processes. These materials show the property of react with gaseous fuels as well as release oxygen under given conditions, while cheap metals are used. In addition, these materials can show magnetic properties that can be used for an easy separation from ash in CLC with solid fuels. Thus, losses of oxygen carrier material in the ash drain stream would be reduced. Different cations have been proposed for improving the magnetic properties of manganese ferrites, including Ti4+. In this context, the present work accomplishes a screening of (MnxFe1−x)2O3 doped with 7 wt.% TiO2, with x ranging from 0 to 1. The influence of Mn:Fe ratio on their physical and chemical properties was evaluated. In general, particles with high crushing strength values (>4 N) were obtained, and magnetic characteristics were highlighted when x ⩽ 0.66. The oxygen uncoupling capability depended on the Mn:Fe ratio and the oxidation conditions, i.e. temperature and oxygen partial pressure. Broader oxidation conditions to take advantage of the oxygen uncoupling capability were found for materials with low Mn content. On contrary, the reactivity with fuel gases (CH4, H2 and CO) increased with the Mn content. Thus, oxygen carriers with Mn/(Mn + Fe) molar ratio in the 0.5–0.9 interval showed interesting properties at suitable temperatures for the iG-CLC and CLOU processes (i.e. 850–980 °C). The material with Mn/(Mn + Fe) = 0.55 was preferred considering a trade-off between reactivity and magnetic properties., This work was partially supported by the Spanish Ministry for Economy and Competitiveness via the ENE2013-45454-R and ENE2014-56857-R projects, by the European Regional Development Fund (ERDF), and by the CSIC via the 2014-80E101 project. M. Abián acknowledges the MINECO and Instituto de Carboquímica (ICB-CSIC) for the post-doctoral grant awarded (FPDI-2013-16172)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Development of (Mn0.77Fe0.23)2O3 particles as an oxygen carrier for coal combustion with CO2 capture via in-situ gasification Chemical Looping Combustion (iG-CLC) aided by Oxygen Uncoupling (CLOU)

  • Pérez-Vega, Raúl
  • Abad Secades, Alberto
  • Gayán Sanz, Pilar
  • Diego Poza, Luis F. de
  • García Labiano, Francisco
  • Adánez Elorza, Juan
© 2017. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Chemical looping combustion (CLC) involves the use of a solid oxygen carrier to transport the oxygen from the air to a fuel. Attention has recently been focused on oxygen carriers based on Mn-Fe mixed oxides because they are cheap materials that are able to release oxygen at high temperature, the so-called oxygen uncoupling step. The aim of this work was to assess the use of (Mn0.77Fe0.23)2O3 material as an oxygen carrier with the ability to transport oxygen both by reduction with gaseous fuels and by oxygen uncoupling, i.e. typical mechanisms in CLC and in Chemical Looping with Oxygen Uncoupling (CLOU), respectively. The particles prepared by mechanical mixing were screened to obtain particles of sufficient reactivity and mechanical strength for use in a fluidized bed reactor. The preparation methodology and calcining temperature were varied. The reactivity of one selected material was evaluated by performing redox cycles both in a TGA and a batch fluidized-bed reactor. Thus, its behaviour was assessed during both decomposition-regeneration of bixbyite phase [(Mn0.77Fe0.23)2O3] in CLOU and the reduction-oxidation of spinel phase [(Mn0.77Fe0.23)3O4] with gaseous fuels, i.e. H2, CO and CH4. Its oxygen uncoupling and re-oxidation capability was highly influenced by the reaction temperature and oxygen concentration. On the other hand, CLC redox cycles with gaseous fuels showed high reactivity with H2 and CO and high oxygen transport capacity by reduction to mangano-wüstite phase [(Mn0.77Fe0.23)O]. Good fluid-dynamic behaviour was observed for the oxygen carrier particles along the redox cycles without agglomeration problems, regardless of the operating conditions used in the batch fluidized-bed reactor. Thus, the selected material was considered a promising candidate for use in both in CLC with syngas and CLC with coal., This work was partially supported by the Spanish Ministry for Economy and Competitiveness via the ENE2013-45454-R, ENE2014-56857-R and ENE2016-77982-R projects, by the European Regional Development Fund (ERDF), and by the Spanish National Research Council (CSIC) via the 2014-80E101 project. R. Pérez-Vega is grateful to MICINN for the FPI Fellowship., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Spray granulated Cu-Mn oxygen carrier for Chemical Looping with Oxygen Uncoupling (CLOU) process

  • Adánez-Rubio, Iñaki
  • Izquierdo Pantoja, María Teresa
  • Abad Secades, Alberto
  • Gayán Sanz, Pilar
  • Diego Poza, Luis F. de
  • Adánez Elorza, Juan
© 2017. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, One form of Chemical Looping Combustion (CLC) with CO2 capture as an alternative to the burning of solid fuels is the Chemical Looping with Oxygen Uncoupling (CLOU) process. The CLOU process requires metal oxides with O2 release capacity at temperatures that are suitable for solid fuel combustion, e.g. copper and manganese oxides. A Cu-Mn mixed oxide comprising 34 wt% CuO and 66 wt% Mn3O4 and prepared by fluidized bed granulation was analysed for use as an oxygen carrier for the CLOU process. TGA and batch fluidized bed reactors were used to investigate oxygen generation rates, agglomeration behaviour and oxygen carrier attrition. A medium volatile coal from South Africa and its char were used as fuel in a batch fluidized bed reactor in a temperature range of 800–930 °C. The Cu-Mn oxygen carrier showed good release O2 rate and a high rate of oxygen transfer by direct gas-solid reaction. The presence of CO as a combustion product appeared only at low oxygen carrier to coal ratios. This material has the capacity to generate O2 at lower temperatures than needed for Cu-based oxygen carriers, which suggests that this material is suitable for work at lower temperatures in a fuel reactor with complete combustion of the fuel. The low attrition rate and attrition index, together with the stable crushing strength of the particles with redox cycles, make this Cu-Mn oxygen carrier suitable for operation in a continuous CLOU unit., This work was supported by the Spanish Ministry of Economy, Industry and Competitiveness via the Projects ENE2013-45454-R, ENE2014-56857-R and ENE2016-77982-R and the European Union FEDER funds., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Comparative evaluation of the performance of coal combustion in 0.5 and 50 kWth Chemical Looping Combustion units with ilmenite, redmud or iron ore as oxygen carrier.

  • Abad Secades, Alberto
  • Mendiara, Teresa
  • Gayán Sanz, Pilar
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
  • Bueno, José A.
  • Pérez-Vega, Raúl
  • Adánez Elorza, Juan
13 figures, 2 tables.-- Work presented at the 13th International Conference on Greenhouse Gas Control Technologies, GHGT-13, 14-18 November 2016, Lausanne, Switzerland, Chemical Looping Combustion (CLC) is one of the most promising technologies to achieve the CO2 capture at a low economic and energetic penalty. In CLC the combustion is split in two steps: fuel combustion assisted by an oxygen carrier in the fuel reactor, and oxygen carrier regeneration in the air reactor by oxygen in air. Usually, the air and fuel reactors are interconnected fluidized beds, with the oxygen carrier circulating between them. Thus, the CO2 capture is inherent to the CLC process. The use of solid fuels in CLC is attracting great attention due to coal is the most abundant fuel, and burning biomass with CO2 capture would allow to reduce the atmospheric CO2 concentration. The in situ Gasification CLC (iG-CLC) allows the conversion of the solid fuel by performing both gasification and combustion of gasification products in the fuel reactor. In iG-CLC complete combustion is not reached, and an oxygen polishing step is required downstream by using a small fraction of pure oxygen., The authors thank the Spanish Ministry of Economy and Competitiveness (MINECO) for the funding received from the ENE2013-45454-R and ENE 2014-56857-R projects, as well as the European Regional Development Fund (ERDF)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Evaluation of (MnxFe1-x)2TiyOz particles as oxygen carrier for Chemical Looping Combustion

  • Abián, María
  • Abad Secades, Alberto
  • Izquierdo Pantoja, María Teresa
  • Gayán Sanz, Pilar
  • Diego Poza, Luis F. de
  • García Labiano, Francisco
  • Adánez Elorza, Juan
Work presented at the 13th International Conference on Greenhouse Gas Control Technologies, GHGT-13, 14-18 November 2016, Lausanne, Switzerland., The present work accomplishes a screening of the performance of Mn-Fe-Ti based oxygen carriers, prepared with different Mn/(Mn+Fe) molar ratios in the general formula (MnyFe1-y)Ti0.15Ox. The oxygen carriers were prepared by physical mixing followed by pelletizing under pressure, calcining, crushing and sieving in the 100-300 μm particle size interval. The characterization of the carriers is based on the evaluation of their crushing strength, magnetic properties and reduction and oxidation behavior through TGA experiments at temperatures suitable for the CLC process (i.e. 850-950 °C). In addition, the main chemical structures of the Mn-Fe-Ti system were identified as a function of the Mn/(Mn+Fe) molar ratio. Oxygen uncoupling property was analyzed by reduction under a N2 atmosphere and the capability to interact with fuel gases was analyzed by using CH4, H2 and CO. Results indicate that the (MnyFe1-y)Ti0.15Ox oxygen carriers with Mn/(Mn+Fe) molar ratios of 0.55-0.87 have very promising properties for the CLC process with solid fuels., This work was partially supported by the Spanish Ministry for Economy and competitiveness via the ENE-2013-45454-R project, by the European Regional Development Fund (ERDF) and by the CSIC via the 2014-80E101 project. M. Abian acknowledges the MINECO and Instituto de Carboquimica (ICB-CSIC) for the post-doctoral grant awarded (FPDI-2013-16172), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Promising impregnated Mn-based oxygen carriers for Chemical Looping Combustion of gaseous fuels

  • Costa, T. R.
  • Gayán Sanz, Pilar
  • Abad Secades, Alberto
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
  • Melo, Dulce M. A.
  • Adánez Elorza, Juan
Promising impregnated oxygen carriers, based on copper and iron, have been previously developed for CLC with gaseous fuels (CH4, syngas, LHC). Recently, because of its low cost and environmental compatibility, Mn-based oxygen carriers are now being considered as an attractive option for chemical-looping combustion (CLC) applications. In this work, a screening of different commercial supports in fluidizable particle size for impregnated Mn-based materials has been carried out. Different oxygen carriers have been prepared by incipient impregnation on ZrO2, and CaAl2O4, and evaluated with respect to their mechanical resistance, fuel gas reactivity and fluidization properties such as agglomeration and attrition rate. In a first step, particles showing high enough crushing strength values were selected for the reactivity investigation. The redox reactivity was evaluated through TGA experiments at suitable temperatures for the CLC process (i.e. 850-950 °C) using H2, CO and CH4. Multi cycle redox analysis and full physical and chemical characterization was also performed. In a second step, materials with high enough reactivity were prepared for fluidized bed evaluation. A batch fluidized bed installation with continuous gaseous fuel feed was used to analyze the product gas distribution during reduction and oxidation reactions at different operation temperatures, and agglomeration and attrition behavior of the selected materials. Results showed that an oxygen carrier impregnated using ZrO2 as support, had high enough reactivity and low attrition rate. Therefore, this material can be selected as a candidate for the development of CLC with syngas with promising results., This work was partially supported by the Spanish Ministry for Economy and Competitiveness via the ENE2013-45454-R project, by the European Regional Development Fund (ERDF), and by the CSIC via the 2014-80E101 project. The authors thanks the CNPq for the funding received from the project 405792/2013-1 and T. Costa thanks the CNPq for the grant SWE 200354/2014-0., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Chemical looping combustion of solid fuels

  • Adánez Elorza, Juan
  • Abad Secades, Alberto
  • Mendiara, Teresa
  • Gayán Sanz, Pilar
  • Diego Poza, Luis F. de
  • García Labiano, Francisco
47 Figuras,11 Tablas.-- Título del postprint: Review and assessment of experimental results from Chemical Looping Combustion units burning solid fuels.-- © 2017. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Chemical Looping Combustion (CLC) has arisen during last years as a very promising combustion technology for power plants and industrial applications, with inherent CO2 capture which reduces the energy penalty imposed on other competing technologies. The use of solid fuels in CLC has been highly developed in the last decade and currently stands at a technical readiness level (TRL) of 6. In this paper, experience gained during CLC operation in continuous units is reviewed and appraised, focusing mainly on technical and environmental issues relating to the use of solid fuels. Up to now, more than 2700 h of operational experience has been reported in 19 pilot plants ranging from 0.5 kWth to 4 MWth. When designing a CLC unit of solid fuels, the preferred configuration for the scale-up is a two circulating fluidized beds (CFB) system. Coal has been the most commonly used solid fuel in CLC, but biomass has recently emerged as a very promising option to achieve negative emissions using bioenergy with carbon dioxide capture and storage (BECCS). Mostly low cost iron and manganese materials have been used as oxygen carriers in the so called in-situ gasification CLC (iG-CLC). The development of Chemical Looping with Oxygen Uncoupling (CLOU) makes a qualitative step forward in the solid fuel combustion, due to the use of materials able to release oxygen. The performance and environmental issues of CLC of solid fuels is evaluated here. Regarding environmental aspects, the pollutant emissions (SO2, NOx, etc.) released into the atmosphere from the air reactor are no cause of concern for the environment. However, the presence of SO2, NOx and Hg at the exit of the fuel reactor affects CO2 quality, which must be taken into account during the later compression and purification stages. The effect of the main variables affecting CLC performance is evaluated for fuel conversion, CO2 capture rate, and combustion efficiency obtained in different CLC units. Solid fuel conversion is normally not complete during operation, due to the undesired loss of char. A methodology is presented to extrapolate the current information to what could be expected in a larger CLC system. CO2 capture near 100% has been reported using a highly efficient carbon stripper, highly reactive fuels (such as lignites and biomass, etc.) or by the CLOU process. Operational experience in iG-CLC has showed that it is not possible to reach complete fuel combustion, making an additional oxygen polishing step necessary. For the further scale-up, it is essential to reduce the unburnt compounds at the fuel reactor outlet. Proposals to achieve this reduction already exist and include both improvement to the gas-oxygen carrier contact, or new design concepts based on the current scheme for iG-CLC. In addition, CLOU based on copper materials has shown that complete fuel combustion could be achieved. Main challenges for the future development and scale-up of CLC technology have been also identified. A breakthrough in the future development of CLC technology for solid fuels will come from developing long-life materials for CLOU that are easy to recover from the ash purge stream., This work was supported by the Spanish Ministry of Economy and Competitiveness (projects ENE 2013-45454-R, ENE2014-56857-R and ENE2016-77982-R), by the European Regional Development Fund (ERDF), by the CSIC (projects 2014-80E101 and 201780E035) and by the Government of Aragón (Spain, Ref. T06). T. Mendiara gives thanks for the Ramón y Cajal post-doctoral contract awarded by the Spanish Ministry of Economy and Competitiveness., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

CLOU process performance with a Cu-Mn oxygen carrier in the combustion of different types of coal with CO2 capture

  • Adánez-Rubio, Iñaki
  • Abad Secades, Alberto
  • Gayán Sanz, Pilar
  • Diego Poza, Luis F. de
  • Adánez Elorza, Juan
5 Figures, 3 Tables.-- © 2017. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, The Chemical Looping with Oxygen Uncoupling (CLOU) process is a Chemical Looping Combustion (CLC) technology that allows the combustion of solid fuels with inherent CO2 separation by using oxygen carriers based on metal oxides. This technology has a low energy penalty and thus low CO2 capture costs. The oxygen carrier used in the CLOU process must be able to release gaseous oxygen, an aspect that limits the availability of metal oxides for this process. This work investigated the suitability of an oxygen carrier containing 34 wt% CuO and 66 wt% Mn3O4 (active phase Cu1.5Mn1.5O4) prepared by granulation regarding the CO2 capture, combustion efficiency and lifetime of the particles. The effect of the different types of coal (two sub-bituminous and a lignite) on combustion and CO2 capture efficiencies by CLOU was studied at different oxygen carrier to coal ratios in a continuous 1.5 kWth rig. It was found that full combustion could be reached regardless of the coal used. However, CO2 capture efficiencies were highly determined by coal rank. Finally, it was found that working with oxygen carrier to coal ratios higher than ϕ = 4, which corresponded to values of the variation of the oxygen carrier conversion lower than ΔXoc = 0.25, decreased the effect of chemical stress on the attrition rate. Therefore, it is clearly beneficial for the lifetime of oxygen carrier particles to operate with low variations of the oxygen carrier conversion (ΔXoc) between fuel and air reactors., This work was supported by the Spanish Ministry of Economy, Industry and Competitiveness (MINECO Projects: ENE2013-45454-R, ENE2014-56857-R and ENE2016-77982-R) and the European Union FEDER funds., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Design and operation of a coal-fired 50 kWth chemical looping combustor

  • Adánez Elorza, Juan
  • Abad Secades, Alberto
  • Pérez-Vega, Raúl
  • Diego Poza, Luis F. de
  • García Labiano, Francisco
  • Gayán Sanz, Pilar
7 figures, 3 tables.-- Work presented at the 12th International Conference on Greenhouse Gas Control Technologies, GHGT-12, 5th - 9th October 2014, Austin, Texas, (USA), CLC technology with solid fuels is being developed mainly by means of two modes: in situ Gasification CLC (iG-CLC) and Chemical Lopping with Oxygen Uncoupling (CLOU). In the iG-CLC concept, coal gasification is an intermediate step taking place inside the fuel reactor, where gasification products (CO+H2) and volatile matter are oxidized by reaction with oxygen carrier particles. The CLOU concept was developed on the strategy of using oxygen carrier materials which can release gaseous oxygen in the fuel reactor environment, and thereby allowing the solid fuel to be quickly burnt with gas phase oxygen. A 50 kWth pilot plant for solid fuels have been designed and constructed to be operated in both iG-CLC and CLOU modes. The design of the concept was based on two interconnected circulating fluidized beds reactors. The coal is fed at the bottom of the fuel reactor to maximize the contact between the volatile matter and the oxygen carrier particles, minimizing the unburnt compounds at the outlet. In iG-CLC mode, residence time of solids in the fuel reactor is low compared to the time to allow complete coal gasification. A carbon stripper has been included between fuel and air reactors to increase the residence time of char particles in the fuel reactor, thus allowing high CO2 capture rates. In this unit, the char particles are separated from the oxygen carrier particles using their different fluidization properties and they are recirculated to the fuel reactor. This unit could be also required for low reactive coals in CLOU mode. Solids circulation flow rate is controlled by using a double loop seal after fuel reactor cyclone. In this device, the solid flow exiting from the fuel reactor splits into two different streams. One goes to the carbon stripper and the other is recirculated to the fuel reactor., We thank the Spanish Ministry for Science and Innovation for financial support via the ENE2013-45454-R project. R. Pérez-Vega thanks for the FPI Fellowship.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Evaluación de minerales de manganeso como transportadores de oxígeno en la combustión de carbón con captura de CO2 mediante el proceso CLC

  • Mendiara, Teresa
  • Mei, Daofeng
  • Gayán Sanz, Pilar
  • Abad Secades, Alberto
  • Adánez Elorza, Juan
Póster presentado en la XIII Reunión del Grupo Español del Carbón, del 18 al 21 de Octubre de 2015, organizada por la Universidad de Alicante con el apoyo del Grupo Español del Carbón., La tecnología Chemical Looping Combustion (CLC) es una de las técnicas más prometedoras dentro de las opciones de captura de CO2 puesto que permite la combustión de carbón con separación inherente de CO2 con un bajo coste. En esta técnica, el oxígeno necesario es aportado por un transportador de oxígeno, normalmente un óxido metálico (MOy), que transfiere el oxígeno del aire al combustible, evitando el contacto directo entre ellos La selección de un transportador de oxígeno barato es importante en la combustión de carbón puesto que parte del transportador es extraido junto con las cenizas., OBJETIVO: Evaluar el comportamiento de varios minerales de manganeso como transportadores de oxígeno en la combustión de carbón, CONCLUSIÓN: El mineral MnGBHNE se propone para su uso en procesos iG-CLC debido a su elevada capacidad de transporte de oxígeno, elevada reactividad y adecuada resistencia mecánica, Este trabajo ha sido financiado por el Ministerio de Economía y Competitividad (MINECO, ENE 2013-45454-R), por fondos FEDER y por el Gobierno de Aragón (DGA, Ref.T06). T. Mendiara agradece al MINECO el contrato “Ramón y Cajal”., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Comparative Evaluation of the Performance of Coal Combustion in 0.5 and 50 kWth Chemical Looping Combustion Units with Ilmenite, Redmud or Iron Ore as Oxygen Carrier

  • Abad, A.
  • Mendiara, T.
  • Gayán, P.
  • García-Labiano, F.
  • De Diego, L.F.
  • Bueno, J.A.
  • Pérez-Vega, R.
  • Adánez, J.
Chemical Looping Combustion (CLC) is one of the most promising technologies to achieve the CO2 capture at a low economic and energetic penalty. In CLC the combustion is split in two steps: fuel combustion assisted by an oxygen carrier in the fuel reactor, and oxygen carrier regeneration in the air reactor by oxygen in air. Usually, the air and fuel reactors are interconnected fluidized beds, with the oxygen carrier circulating between them. Thus, the CO2 capture is inherent to the CLC process. The use of solid fuels in CLC is attracting great attention due to coal is the most abundant fuel, and burning biomass with CO2 capture would allow to reduce the atmospheric CO2 concentration. The in situ Gasification CLC (iG-CLC) allows the conversion of the solid fuel by performing both gasification and combustion of gasification products in the fuel reactor. In iG-CLC complete combustion is not reached, and an oxygen polishing step is required downstream by using a small fraction of pure oxygen. In this work, an overview of the operational experience in ICB-CSIC is presented. Results obtained in 0.5 kWth and 50 kWth CLC units burning different coals with ilmenite, redmud or iron ore are compiled and critically compared. Insights were obtained in order to achieve high CO2 capture and combustion efficiency values. Eventually, the use of ring-type internals in the fuel reactor of the 50 kWth CLC unit was accomplished to promote the gas-solid contact, thus increasing the combustion efficiency.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Promising Impregnated Mn-based Oxygen Carriers for Chemical Looping Combustion of Gaseous Fuels

  • Costa, T.R.
  • Gayán, P.
  • Abad, A.
  • García-Labiano, F.
  • De Diego, L.F.
  • Melo, D.M.A.
  • Adánez, J.
Promising impregnated oxygen carriers, based on copper and iron, have been previously developed for CLC with gaseous fuels (CH4, syngas, LHC). Recently, because of its low cost and environmental compatibility, Mn-based oxygen carriers are now being considered as an attractive option for chemical-looping combustion (CLC) applications. In this work, a screening of different commercial supports in fluidizable particle size for impregnated Mn-based materials has been carried out. Different oxygen carriers have been prepared by incipient impregnation on ZrO2, and CaAl2O4, and evaluated with respect to their mechanical resistance, fuel gas reactivity and fluidization properties such as agglomeration and attrition rate. In a first step, particles showing high enough crushing strength values were selected for the reactivity investigation. The redox reactivity was evaluated through TGA experiments at suitable temperatures for the CLC process (i.e. 850-950 °C) using H2, CO and CH4. Multi cycle redox analysis and full physical and chemical characterization was also performed. In a second step, materials with high enough reactivity were prepared for fluidized bed evaluation. A batch fluidized bed installation with continuous gaseous fuel feed was used to analyze the product gas distribution during reduction and oxidation reactions at different operation temperatures, and agglomeration and attrition behavior of the selected materials. Results showed that an oxygen carrier impregnated using ZrO2 as support, had high enough reactivity and low attrition rate. Therefore, this material can be selected as a candidate for the development of CLC with syngas with promising results.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Evaluation of (MnxFe1-x)2TiyOz Particles as Oxygen Carrier for Chemical Looping Combustion

  • Abián, M.
  • Abad, A.
  • Izquierdo, M.T.
  • Gayán, P.
  • De Diego, L.F.
  • García-Labiano, F.
  • Adánez, J.
The present work accomplishes a screening of the performance of Mn-Fe-Ti based oxygen carriers, prepared with different Mn/(Mn+Fe) molar ratios in the general formula (MnyFe1-y)Ti0.15Ox. The oxygen carriers were prepared by physical mixing followed by pelletizing under pressure, calcining, crushing and sieving in the 100-300 µm particle size interval. The characterization of the carriers is based on the evaluation of their crushing strength, magnetic properties and reduction and oxidation behavior through TGA experiments at temperatures suitable for the CLC process (i.e. 850-950 °C). In addition, the main chemical structures of the Mn-Fe-Ti system were identified as a function of the Mn/(Mn+Fe) molar ratio. Oxygen uncoupling property was analyzed by reduction under a N2 atmosphere and the capability to interact with fuel gases was analyzed by using CH4, H2 and CO. Results indicate that the (MnyFe1-y)Ti0.15Ox oxygen carriers with Mn/(Mn+Fe) molar ratios of 0.55-0.87 have very promising properties for the CLC process with solid fuels.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

CLOU process performance with a Cu-Mn oxygen carrier in the combustion of different types of coal with CO2 capture

  • Adanez-Rubio, I.
  • Abad, A.
  • Gayan, P.
  • de Diego, L.F.
  • Adanez, J.
The Chemical Looping with Oxygen Uncoupling (CLOU) process is a Chemical Looping Combustion (CLC) technology that allows the combustion of solid fuels with inherent CO2 separation by using oxygen carriers based on metal oxides. This technology has a low energy penalty and thus low CO2 capture costs. The oxygen carrier used in the CLOU process must be able to release gaseous oxygen, an aspect that limits the availability of metal oxides for this process. This work investigated the suitability of an oxygen carrier containing 34 wt% CuO and 66 wt% Mn-3 O-4 (active phase Cu1.5Mn1.5O4) prepared by granulation regarding the CO2 capture, combustion efficiency and lifetime of the particles. The effect of the different types of coal (two sub-bituminous and a lignite) on combustion and CO2 capture efficiencies by CLOU was studied at different oxygen carrier to coal ratios in a continuous 1.5 kWth rig. It was found that full combustion could be reached regardless of the coal used. However, CO2 capture efficiencies were highly determined by coal rank. Finally, it was found that working with oxygen carrier to coal ratios higher than phi = 4, which corresponded to values of the variation of the oxygen carrier conversion lower than Delta X-oc = 0.25, decreased the effect of chemical stress on the attrition rate. Therefore, it is clearly beneficial for the lifetime of oxygen carrier particles to operate with low variations of the oxygen carrier conversion (Delta X-oc) between fuel and air reactors.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Titanium substituted manganese-ferrite as an oxygen carrier with permanent magnetic properties for chemical looping combustion of solid fuels

  • Abián, María
  • Abad, Alberto
  • Izquierdo, María T.
  • Gayán, Pilar
  • de Diego, Luis F.
  • García-Labiano, Francisco
  • Adánez, Juan
Mixed oxides of Mn-Fe have been identified as suitable materials for Chemical Looping Combustion (CLC) with solid fuels both via in-situ Gasification Chemical Looping Combustion (iG-CLC) and Chemical Looping with Oxygen Uncoupling (CLOU) processes. These materials show the property of react with gaseous fuels as well as release oxygen under given conditions, while cheap metals are used. In addition, these materials can show magnetic properties that can be used for an easy separation from ash in CLC with solid fuels. Thus, losses of oxygen carrier material in the ash drain stream would be reduced. Different cations have been proposed for improving the magnetic properties of manganese ferrites, including Ti4+. In this context, the present work accomplishes a screening of (MnxFe1-x)2O3 doped with 7 wt.% TiO2, with x ranging from 0 to 1. The influence of Mn:Fe ratio on their physical and chemical properties was evaluated. In general, particles with high crushing strength values (>4 N) were obtained, and magnetic characteristics were highlighted when x ¿ 0.66. The oxygen uncoupling capability depended on the Mn:Fe ratio and the oxidation conditions, i.e. temperature and oxygen partial pressure. Broader oxidation conditions to take advantage of the oxygen uncoupling capability were found for materials with low Mn content. On contrary, the reactivity with fuel gases (CH4, H2 and CO) increased with the Mn content. Thus, oxygen carriers with Mn/(Mn + Fe) molar ratio in the 0.5–0.9 interval showed interesting properties at suitable temperatures for the iG-CLC and CLOU processes (i.e. 850–980 °C). The material with Mn/(Mn + Fe) = 0.55 was preferred considering a trade-off between reactivity and magnetic properties.