Skip to main content

DESARROLLO DE UNA PLATAFORMA MULTIFISICA DE ALTAS PRESTACIONES PARA SIMULACIONES TERMOHIDRAULICO-NEUTRONICAS EN INGENIERIA NUCLEAR

ENE2012-34585

•
Funding agency name Ministerio de Economía y Competitividad
Funding agency acronym MINECO
Program Programa Nacional de Proyectos de Investigación Fundamental
Subprogram Subprograma de Proyectos de Investigación Fundamental no Orientada
Call Proyectos I+D
Call year 2012
State Plan 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Management unit Secretaría de Estado de Investigación, Desarrollo e Innovación
Beneficiary centre UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 18
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Application case for phase III of UAM-LWR benchmark: Uncertainty propagation of thermal-hydraulic macroscopic parameters

  • Mesado, C.
  • Miró Herrero, Rafael|||0000-0003-1012-0869
  • Verdú Martín, Gumersindo Jesús|||0000-0001-5098-080X
[EN] This work covers an important point of the benchmark released by the expert group on Uncertainty Analysis in Modeling of Light Water Reactors. This ambitious benchmark aims to determine the uncertainty in light water reactors systems and processes in all stages of calculation, with emphasis on multi-physics (coupled) and multi-scale simulations. The Gesellschaft für Anlagen und Reaktorsicherheit methodology is used to propagate the thermal-hydraulic uncertainty of macroscopic parameters through TRACE5.0p3/PARCSv3.0 coupled code. The main innovative points achieved in this work are i) a new thermal-hydraulic model is developed with a highly-accurate 3D core discretization plus an iterative process is presented to adjust the 3D bypass flow, ii) a control rod insertion occurrence ¿which data is obtained from a real PWR test¿ is used as a transient simulation, iii) two approaches are used for the propagation process: maximum response where the uncertainty and sensitivity analysis is performed for the maximum absolute response and index dependent where the uncertainty and sensitivity analysis is performed at each time step, and iv) RESTING MATLAB code is developed to automate the model generation process and, then, propagate the thermal-hydraulic uncertainty. The input uncertainty information is found in related literature or, if not found, defined based on expert judgment. This paper, first, presents the Gesellschaft für Anlagen und Reaktorsicherheit methodology to propagate the uncertainty in thermal-hydraulic macroscopic parameters and, then, shows the results when the methodology is applied to a PWR reactor., The authors of this work thank the UAM-LWR benchmark organizers without whom this work would not have been possible. Besides, the authors sincerely thank to the Ministerio de Economia, Industria y Competitividad and the "Plan Nacional de I+D+i" for funding the projects NUC-MULTPHYS ENE2012-34585 and ENE2017-89029-P.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Verification of the Parallel Pin-Wise Core Simulator pCTF/PARCSv3.2 in Operational Control Rod Drop Transient Scenarios

  • Ramos Peinado, Enrique|||0000-0002-5960-5501
  • Jose E. Roman|||0000-0003-1144-6772
  • Miró Herrero, Rafael|||0000-0003-1012-0869
  • Abarca Giménez, Agustín
  • Bermejo, Juan A.
  • Ortego, Alberto
  • Posada-Barral, Jose Maria
[EN] Thanks to advances in computer technology, it is feasible to obtain detailed reactor core descriptions for safety analysis of the light water reactor (LWR), in order to represent realistically the fuel elements design, as is the case for three-dimensional coupled simulations for local neutron kinetics and thermal hydraulics. This scenario requires an efficient thermal-hydraulic code that can produce a response in a reasonable time for large-scale, detailed models. In two-fluid codes, such as the thermal-hydraulic subchannel code COBRA-TF, the time restriction is even more important, since the set of equations to be solved is more complex. We have developed a message passing interface parallel version of COBRA-TF, called pCTF. The parallel code is based on a cell-oriented domain decomposition approach, and performs well in models that consist of many cells. The Jacobian matrix is computed in parallel, with each processor in charge of calculating the coefficients related to a subset of the cells. Furthermore, the resulting system of linear equations is also solved in parallel, by exploiting solvers and preconditioners from PETSc. The goal of this study is to demonstrate the capability of the recently developed pCTF/PARCS coupled code to simulate large cores with a pin-by-pin level of detail in an acceptable computational time, using for this purpose two control rod drop operational transients that took place in the core of a three-loop pressurized water reactor. As a result, the main safety parameters of the core hot channel have been calculated by the coupled code in a pin level of detail, obtaining best estimate results for this transient., This work has been partially supported by the Universitat Politecnica de Valencia under Projects COBRA_PAR (PAID-05-11-2810) and OpenNUC (PAID-05-12), and by the Spanish Ministerio de Economia y Competitividad under Projects SLEPc-HS (TIN2016-75985-P) and NUC-MULTPHYS (ENE2012-34585).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Analysis of the Core Exit Temperature and the Peak Cladding Temperature during a SBLOCA. Application to a scaled-up model

  • Querol, A.
  • Gallardo Bermell, Sergio|||0000-0002-3703-9983
  • Verdú Martín, Gumersindo Jesús|||0000-0001-5098-080X
[EN] During Loss-Of-Coolant Accidents (LOCA), operators may start Accident Management (AM) actions when the Core Exit Temperature (CET) measured by thermocouples exceeds a certain value. However, a significant time delay and temperature discrepancy in the superheat detection was observed in several facilities. This work is focused on clarifying CET thermocouple responses versus Peak Cladding Temperature (PCT) and to study if the same physical phenomena are reproduced in two TRACE5 models with different geometry (a Large Scale Test Facility (LSTF) and a scaled-up LSTF) during a pressure vessel upper head Small Break LOCA (SBLOCA). Results obtained show that the delay between the core uncover and the CET excursion is reproduced in both cases., The authors are grateful to the Management Board of the OECD-NEA ROSA Project; thus, this work contains findings produced within this project. This work is partially supported by the Grant-in-Aid for Scientific Research of the Spanish Ministerio de Educacion (Grant number: AP2009-2600), the Spanish Ministerio de Ciencia e Innovacion under Projects ENE2011-22823 and ENE2012-34585, and the Generalitat Valenciana under Projects PROMETEOII/2014/008 and ACOMP/2013/237.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Simulation of a SBLOCA in a hot leg. Scaling considerations andapplication to a nuclear power plant

  • Querol Vives, Andrea
  • Gallardo Bermell, Sergio|||0000-0002-3703-9983
  • Verdú Martín, Gumersindo Jesús|||0000-0001-5098-080X
The main goal of this work is to study the physical phenomena observed during a Small Break Loss-Of-Coolant Accident transient performed in a small-scale Integral Test Facility and to determine the capabilityof the thermal hydraulic code TRACE5 to reproduce these phenomena in a scale-up model. The accidentscenario analyzed is based on Test 1.2 in the frame of the OECD/NEA ROSA Project, which simulatesa 1% hot leg Small Break Loss-Of-Coolant Accident in the Large Scale Test Facility of the Japan AtomicEnergy Agency. During this test, natural circulation in primary loops occurs, cooling the core during someminutes. This is an important phenomenon, which needs to be checked by means of different TRACE5models. With this aim, Test 1 2 has been simulated using a TRACE5 model reproducing the geometricaland thermal hydraulic features of Large Scale Test Facility. In order to determine if this phenomenon canbe reliably extrapolated to a scale-up plant, a new TRACE5 model has been developed. The geometricalfeatures of this scale-up model are determined using a fixed scaling ratio respect to the original LSTFfeatures. On the other hand, 4 and 3-loop standard Westinghouse PWR models are used in order tosimulate the same transient and compare the behaviour of the main thermal hydraulic variables withthose obtained in the Large Scale Test Facility model and in the Large Scale Test Facility scale-up model.Results show that both Large Scale Test Facility and the scale-up models present the same behaviourduring the whole transient. Important discrepancies are found in the results corresponding to 4 and3-loop PWR TRACE5 models. In both models, natural circulation is not properly reproduced. Trying toimprove the simulation results, the nodalizations of U-tubes and pressure vessel were tested. Resultsstate that the nodalization of U-tubes clearly affects the natural circulation simulation. However, thevessel nodalization effect is not as important., This work contains findings produced within the OECD-NEA ROSA Project. This work is partially supported by the Grant-in-Aid for Scientific Research of the Spanish Ministerio de Educacion (Grant number: AP2009-2600), the Spanish Ministerio de Ciencia e Innovacion under Projects ENE2011-22823 and ENE2012-34585 and the Generalitat Valenciana under Projects PROMETEO/2010/039 and ACOMP/2013/237.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Plataforma Multifísica de Altas Prestaciones para Análisis de Seguridad en Ingeniería Nuclear, High performance multiphysics platform for nuclear safety analysis

  • Abarca Giménez, Agustín
  • Melara-San Román, José
  • Concejal-Bermejo, Alberto
  • Miró Herrero, Rafael|||0000-0003-1012-0869
  • Verdú Martín, Gumersindo Jesús|||0000-0001-5098-080X
[ES] En los últimos años, paralelamente a los avances en tecnología informática, se están desarrollando herramientas informáticas mediante las que es posible obtener una descripción detallada de los fenómenos que tienen lugar en el núcleo de los reactores nucleares. El objeto de estas nuevas herramientas es el de realizar análisis de seguridad en reactores nucleares utilizando técnicas de mejor estimación. Las técnicas de mejor estimación, en contraposición con las conservadoras, permiten la operación del reactor con márgenes de seguridad más estrechos y, por tanto, mayor economía del núcleo. En este contexto se desarrolla una plataforma informática que integra códigos informáticos que cubren la mayor parte de las físicas que tienen lugar en los reactores nucleares. Para la integración de los diferentes fenómenos de realimentación entre termohidráulica, neutrónica, mecánica y transmisión de calor se han desarrollado una serie de acoplamientos entre los códigos que componen la plataforma. Todos los desarrollos realizados tienen por objetivo representar de forma realista el diseño y comportamiento de la instalación nuclear, incluyendo el sistema de control, los elementos y las varillas de combustible., [EN] In recent years, in parallel with advances in computer technology, computer tools have been developed through which it is possible to obtain a detailed description of the phenomena occurring in the core of nuclear reactors. The final objective of these new tools is to perform safety analysis using best estimate techniques. The best estimate techniques, as opposed to the conservative ones, allow the operation of the reactor with narrower safety margins, and thus greater core economy. In this context, it has been developed a multiphysics computer platform that integrates simulation codes that cover most of the physics that take place in nuclear reactors. For the integration of the different feedback phenomena between thermal-hydraulics, neutronics and heat transfer, a series of couplings have been developed between the codes that compose the platform. All the developments carried out are intended to realistically represent the design and behavior of the nuclear facility, including the control system, fuel elements and fuel rods., Este trabajo se enmarca dentro de la línea de investigación financiada por el Ministerio de Economía y Competitividad en el proyecto NUC-MULTPHYS (ENE2012-34585) y los proyectos de colaboración interdisciplinar de la Universitat Politècnica de Valencia COBRA_PAR (PAID - 05 -11-2810) y Open-NUC (PAID-05-12)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Mejoras en la versión paralela del código termohidráulico de subcanal COBRA-TF

  • Ramos Peinado, Enrique|||0000-0002-5960-5501
  • Jose E. Roman|||0000-0003-1144-6772
  • Miró Herrero, Rafael|||0000-0003-1012-0869
  • Abarca Giménez, Agustín
[ES] Realizar análisis en seguridad nuclear a nivel de varilla de combustible requiere las ejecución de códigos acoplados neutrónicotermohidráulicos que permitan la simulación de grandes dominios físicos en un tiempo razonable. Para ello resulta imprescindible el uso de numerosos procesadores (o núcleos) que colaboren en la obtención de la solución a un único problema utilizando la potencia computacional y de memoria disponible en un clúster. En anteriores trabajos se presentó la paralelización del código termohidráulico de subcanal COBRA-TF (CTF) mediante la tecnología MPI (Message Passing Interface) y utilizando la librería paralela de métodos numéricos PETSc para resolver el sistema lineal de ecuaciones del código. En el presente documento se expondrán las mejoras introducidas en código acoplado, centradas tanto en la parte de optimización de memoria como en paralelismo, además se ha combinado la tecnología MPI y la PVM (Parallel Virtual Machine) para posibilitar el uso del código acoplado CTF/PARCSV2.7., Este trabajo ha sido parcialmente esponsorizado por la Universitat Politècnica de València bajo los proyectos COBRA_PAR PAID-05-11-2810 y OpenNUC PAID-05-12 y por el Ministerio de Economía y Competitividad a través del proyecto NUC-MULTPHYS ENE-2012-34585 financiado por los fondos FEDER de la Unión Europea.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Development of a Finite Volume Inter-cell Polynomial Expansion Method for the Neutron Diffusion Equation

  • Bernal García, Álvaro
  • Jose E. Roman|||0000-0003-1144-6772
  • Miró Herrero, Rafael|||0000-0003-1012-0869
  • Ginestar Peiro, Damián|||0000-0003-1243-6648
  • Verdú Martín, Gumersindo Jesús|||0000-0001-5098-080X
Heterogeneous nuclear reactors require numerical methods to solve the neutron diffusion equation (NDE) to obtain the neutron flux distribution inside them, by discretizing the heterogeneous geometry in a set of homogeneous regions. This discretization requires additional equations at the inner faces of two adjacent cells: neutron flux and current continuity, which imply an excess of equations. The finite volume method (FVM) is suitable to be applied to NDE, because it can be easily applied to any mesh and it is typically used in the transport equations due to the conservation of the transported quantity within the volume. However, the gradient and face-averaged values in the FVM are typically calculated as a function of the cell-averaged values of adjacent cells. So, if the materials of the adjacent cells are different, the neutron current condition could not be accomplished. Therefore, a polynomial expansion of the neutron flux is developed in each cell for assuring the accomplishment of the flux and current continuity and calculating both analytically. In this polynomial expansion, the polynomial terms for each cell were assigned previously and the constant coefficients are determined by solving the eigenvalue problem with SLEPc. A sensitivity analysis for determining the best set of polynomial terms is performed., This work has been partially supported by the Spanish Ministerio de Eduacion Cultura y Deporte [grant number FPU13/01009]; the Spanish Ministerio de Ciencia e Innovacion [project number ENE2014-59442-P], [project number ENE2012-34585]; the Generalitat Valenciana [project number PROMETEOII/2014/008]; the Universitat Politecnica de Valencia [project number UPPTE/2012/118]; and the Spanish Ministerio de Economia y Competitividad [project number TIN2013-41049-P].
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Problema de autovalores de la ecuación de la difusión neutrónica discretizada con el Método de Volúmenes Finitos en un PWR

  • Bernal García, Álvaro
  • Jose E. Roman|||0000-0003-1144-6772
  • Miró Herrero, Rafael|||0000-0003-1012-0869
  • Verdú Martín, Gumersindo Jesús|||0000-0001-5098-080X
En este trabajo, se ha desarrollado un algoritmo para aplicar el Método de Volúmenes Finitos (MVF) a la ecuación de la difusión neutrónica, que calcula varios autovalores y se ha incorporado al algoritmo la lectura de secciones eficaces en función de variables termohidráulicas. Para su validación, se ha simulado un reactor PWR, cuyas secciones eficaces se han modelado con la metodología SIMTAB para las condiciones termohidráulicas de Begin of Cycle (BOC) y Hot Full Power (HFP). Se ha realizado un análisis de sensibilidad de la discretización de la geometría, utilizando 3 mallas de hexaedros y otras 3 de tetraedros. En cada caso, se calculan 5 autovalores y sus correspondientes potencias., Este trabajo ha sido financiado parcialmente por el Ministerio de Educación Cultura y Deporte bajo la beca FPU13/01009, el Ministerio de Ciencia e Innovación bajo los proyectos ENE2014-59442-P y ENE2012-34585, la Generalitat Valenciana bajo el proyecto PROMETEOII/2014/008, la Universitat Politècnica de València bajo el proyecto UPPTE/2012/118, y el Ministerio de Economía y Competitividad bajo el proyecto TIN2013-41049-P.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Control rod drop transient analysis with the coupled parallel code pCTF-PARCSv2.7

  • Ramos Peinado, Enrique|||0000-0002-5960-5501
  • Jose E. Roman|||0000-0003-1144-6772
  • Miró Herrero, Rafael|||0000-0003-1012-0869
  • Abarca Giménez, Agustín
  • Bermejo, Juan A.
In order to reduce the response time when simulating large reactors in detail, a parallel version of the thermal–hydraulic subchannel code COBRA-TF (CTF) has been developed using the standard Message Passing Interface (MPI). The parallelization is oriented to reactor cells, so it is best suited for models consisting of many cells. The generation of the Jacobian matrix is parallelized, in such a way that each processor is in charge of generating the data associated with a subset of cells. Also, the solution of the linear system of equations is done in parallel, using the PETSc toolkit. With the goal of creating a powerful tool to simulate the reactor core behavior during asymmetrical transients, the 3D neutron diffusion code PARCSv2.7 (PARCS) has been coupled with the parallel version of CTF (pCTF) using the Parallel Virtual Machine (PVM) technology. In order to validate the correctness of the parallel coupled code, a control rod drop transient has been simulated comparing the results with the real experimental measures acquired during an NPP real test. 2015 Elsevier Ltd. All rights reserved., This work has been partially supported by the Universitat Politecnica de Valencia under Projects COBRA_PAR (PAID-05-11-2810) and OpenNUC (PAID-05-12), and by the Spanish Ministerio de Economa y Competitividad under Projects SLEPc-PFE (TIN2013-41049-P) and NUC-MULTPHYS (ENE2012-34585). The authors would like to acknowledge the technical support provided by CNAT and IBERDROLA GENERACION S.A. for the realization of this work.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Analysis of Thermal-hydraulic Fluctuations in Trillo NPP with CTF/PARCS v. 2.7 Coupled Code

  • Abarca Giménez, Agustín
  • Bermejo, J. A.
  • Miró Herrero, Rafael|||0000-0003-1012-0869
  • Verdú Martín, Gumersindo Jesús|||0000-0001-5098-080X
[EN] The low-frequency noises are fluctuations in the neutron flux density, in the low-frequency range up to 4 Hz, which generate noise in the neutron instrumentation and could affect the limitation and protection system of the reactor core. Some European pressurized water reactors (PWRs) experienced the effect of low-frequency noise, opening a new research line for the verification of the neutron-kinetics/thermal-hydraulic coupled codes. A CTF/PARCS v. 2.7 simulation study to verify whether periodical fluctuations in the core inlet temperature could activate the core protection system has been done, obtaining the frequency spectrum of the power oscillation amplitudes., This work has been supported by the Ministerio de Economia y Competitividad under the project NUC-MULTPHYS ENE-2012-34585 and sponsored by the FEDER funds of the European Union.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Methodology for neutronic uncertainty propagation and application to a UAM-LWR benchmark

  • Mesado, C.
  • Miró Herrero, Rafael|||0000-0003-1012-0869
  • Verdú Martín, Gumersindo Jesús|||0000-0001-5098-080X
[EN] This work covers an important point of the benchmark released by the expert group on Uncertainty Analysis in Modeling of Light Water Reactors (UAM-LWR). This ambitious benchmark aims to determine the uncertainty in LWR systems and processes in all stages of calculation, with emphasis on multi-physics (coupled) and multi-scale simulations. Specifically, in this work, a simplified BWR core is used to propagate the uncertainty of nuclear data. Due to a high computational cost in the analysis all fuel assemblies are modeled as fresh. The propagation is subdivided into two levels i) assembly level ¿with SCALE6.2.1 and SAMPLER module¿, and ii) core level, ¿with PARCSv3.2 and DAKOTA 6.3¿. The first level takes into account the uncertainties contained in the master library ENDF/B-VII.1 and as a result a problem-dependent neutronic library in NEMTAB format is obtained using TXT2NTAB code. This is a friendly Matlab code developed within this work. Finally, the uncertainty contained in the neutronic library is further propagated through PARCS. A different approach is presented in this work to propagate the uncertainty between codes. Following this approach only two neutronic libraries are generated, one with the average responses and the other with their standard deviations. Then, the standard deviation and a matrix of perturbation factors are used to perturb the main neutronic parameters. A parallel work is done to propagate the thermal-hydraulic parameters in a PWR core., The authors of this work thank IBERINCO (Iberdrola Ingenieria y Construcci.on, S. A.) for the shared data which made possible the validation of the lattice physics model. Moreover, this work was possible thanks to the UAM-LWR benchmark release, thanks to its organizers who requested the development of TXT2NTAB Matlab program. Finally, the authors sincerely thank to the Ministerio de Economia, Industria y Competitividad, Spain and the "Plan Nacional de IthornDthorni" for funding the projects NUC-MULTPHYS ENE2012-34585 and ENE2017-89029-P.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A multi-scale and multi-physics simulation methodology with the state-of-the-art tools for safety analysis in Light Water Reactors applied to a Turbine Trip scenario (Part II)

  • Hidalga-García-Bermejo, Patricio
  • Abarca Giménez, Agustín
  • SEKHRI, ABDELKRIM
  • Miró Herrero, Rafael|||0000-0003-1012-0869
  • Verdú Martín, Gumersindo Jesús|||0000-0001-5098-080X
[EN] The development of the computer technology, as well as the research in the different science fields governing the core behavior of a Light Water Reactor, allows implementing all the known physics and consider detailed scales of analysis. Conversely to conservative approaches, the Best Estimate approach applies the available science by means of models and correlations that are applied in different scales using simulation tools. With this approach, the critical elements of the core can be evaluated with realistic predictions that can adjust the operation conditions and core design to more cost-efficient values without compromising the safety of the Nuclear Power Plant. The authors of this paper present the second part of a multi-scale and multi-physics methodology for the evaluation of fast transients in Light Water Reactors. In this part, the results obtained from the coupled Neutron Kinetics and Thermal-Hydraulics channel-by-channel core model are used for a detailed thermal-hydraulic pin-by-pin analysis and thermomechanics pin model. The aim of this work is to evaluate the safety analysis of the critical fuel rod in Turbine Trip scenario. For that purpose, the critical fuel rod is located using the minimum Critical Power Ratio. This safety variable is predicted in a thermal-hydraulic pin-by-pin model using CTF-UPVIS code. Afterwards, the conditions of the critical rod are loaded in a pin model for a simulation with FRAPCON/FRAPTRAN. Moreover, this paper proves the Best Estimate capability of the presented methodology by means of comparing the results with equivalent simulations that are more conservative, or consist of more limited simulation scales. On the one hand, the Best Estimate prediction is compared against the envelope of the minimum Critical Power Ratio along the axial nodal distribution of the simulated fuel rod. In addition, another comparison is made against assuming constant fuel-cladding gas conductance, showing the enhancement added by considering the axial distribution of this parameter, provided by FRAPCON/FRAPTRAN. On the other hand, the results of this methodology are compared against the limitation of accounting only the bundle radial average value of the minimum Critical Power Ratio. Furthermore, the Best Estimate results are complemented with an Uncertainty and Sensitivity analysis that will define the statistical boundaries of the prediction according to the 95/95 criterion., The authors of this paper acknowledge the technical and economic support of KKL that made possible this project. The acknowledgement is extended to the collaboration of KKL in the research tasks by sharing plant measurements to validate the methodology and to use their software resources to generate useful data for the code-to-code verification.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

On the One-Dimensional Modeling of Vertical Upward Bubbly Flow

  • Peña-Monferrer, C.
  • Gómez-Zarzuela, C.
  • Chiva, S.
  • Miró Herrero, Rafael|||0000-0003-1012-0869
  • Verdú Martín, Gumersindo Jesús|||0000-0001-5098-080X
  • J. L. Muñoz-Cobo|||0000-0002-4512-7991
[EN] The one-dimensional two-fluid model approach has been traditionally used in thermal-hydraulics codes for the analysis of transients and accidents in water¿cooled nuclear power plants. This paper investigates the performance of RELAP5/MOD3 predicting vertical upward bubbly flow at low velocity conditions. For bubbly flow and vertical pipes, this code applies the drift- velocity approach, showing important discrepancies with the experiments compared. Then, we use a classical formulation of the drag coefficient approach to evaluate the performance of both approaches. This is based on the critical Weber criteria and includes several assumptions for the calculation of the interfacial area and bubble size that are evaluated in this work. A more accurate drag coefficient approach is proposed and implemented in RELAP5/MOD3. Instead of using the Weber criteria, the bubble size distribution is directly considered. This allows the calculation of the interfacial area directly from the definition of Sauter mean diameter of a distribution. The results show that only the proposed approach was able to predict all the flow characteristics, in particular the bubble size and interfacial area concentration. Finally, the computational results are analyzed and validated with cross-section area average measurements of void fraction, dispersed phase velocity, bubble size, and interfacial area concentration., The authors sincerely thank the Plan Nacional de I+D+i for funding the Projects MODEXFLAT ENE2013-48565-C2-1- P, ENE2013-48565-C2-2-P, and NUC-MULTPHYS ENE2012- 34585.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Cross-Section Generation Using TXT2NTAB Code for Uncertainty Propagation with Burnup Dependence

  • Labarile, A.|||0000-0003-1610-7606
  • Miró Herrero, Rafael|||0000-0003-1012-0869
  • Verdú Martín, Gumersindo Jesús|||0000-0001-5098-080X
  • Mesado, C.
[EN] One of the challenges of studying the neutronics of reactors is to generate reliable parameterized libraries that contain information to simulate the core in all possible operational and transient conditions. These libraries must include tables of cross sections and other neutronic and kinetic parameters and are obtained by simulating all the segments in a transport code. At the lattice level, one can use branch calculations to change ¿instantaneously¿ the feedback parameters as a function of burnup. When using random sampling for the lattice calculations, one can obtain statistical information about the output parameters and use it in a core simulation to characterize the accuracy of data estimating uncertainties when simulating a heterogeneous system at different scales of detail. This work presents the methodology to generate NEMTAB libraries from data obtained in the SCALE code system to be used in PARCS simulations. The code TXT2NTAB is used to reorder the cross-section tables in NEMTAB format and generate another NEMTAB of standard deviation. With these libraries, the authors perform a steady-state calculation for a light water reactor to propagate several uncertainties at the core level. The methodology allows obtaining statistical information of the most important output parameters: multiplication factor keff, axial power peak Pz, and axial peak node Nz., This work has been partially supported by Spanish Ministerio de Economia y Competitividad under projects ENE2017-89029-P.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Validation of 3D neutronic-thermalhydraulic coupled codes RELAP5/PARCSv2.7 and TRACEv5.0P3/PARCSv3.0 against a PWR control rod drop transient

  • Garcia-Fenoll, Marina
  • Mesado Melia, Carles
  • Bermejo, Juan Antonio
  • López, Arturo
  • Ortego, Alberto
  • Barrachina, Teresa|||0000-0001-8794-4204
  • Miró Herrero, Rafael|||0000-0003-1012-0869
  • Verdú Martín, Gumersindo Jesús|||0000-0001-5098-080X
[EN] In nuclear safety field, neutronic and thermalhydraulic codes performance is an important issue. New capabilities implementation, as well as models and tools improvements are a significant part of the community effort in looking for better Nuclear Power Plants (NPP) designs. A procedure to analyze the PWR response to local deviations on neutronic or thermalhydraulic parameters is being developed. This procedure includes the simulation of Incore and Excore neutron flux detectors signals. A control rod drop real plant transient is used to validate the used codes and their new capabilities. Cross-section data are obtained by means of the SIMTAB methodology. Detailed thermalhydraulic models were developed: RELAP5 and TRACE models simulate three different azimuthal zones. Besides, TRACE model is performed with a fully 3D core, thus, the cross-flow can be obtained. A cartesian vessel represents the fuel assemblies and a cylindrical vessel the bypass and downcomer. Simulated detectors signals are obtained and compared with the real data collected during a control rod drop trial at a PWR NPP and also with data obtained with SIMULATE-3K code., The authors would like to acknowledge the economic support provided by Centrales Nucleares Almaraz-Trillo (CNAT) and IBERDROLA Ingeniería y Construcción (Iberinco) for the realization of this work, and express their great appreciation to Arturo López, Juan Antonio Bermejo and Alberto Ortego for their valuable collaboration and their willingness to develop this work. This work has also been supported by the Spanish Ministerio de Economía y Competitividad, through the projects NUC-MULTPHYS (ENE2012-34585) and VALIUN-3D (ENE2011-22823), and the Generalitat Valenciana (GVA), through the project PROMETEO II/2014/008.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Resolution of the generalized eigenvalue problem in the neutron diffusion equation discretized by the finite volume method

  • Bernal García, Álvaro
  • Miró Herrero, Rafael|||0000-0003-1012-0869
  • Ginestar Peiro, Damián|||0000-0003-1243-6648
  • Verdú Martín, Gumersindo Jesús|||0000-0001-5098-080X
Numerical methods are usually required to solve the neutron diffusion equation applied to nuclear reactors due to its heterogeneous nature. The most popular numerical techniques are the Finite Difference Method (FDM), the Coarse Mesh Finite Difference Method (CFMD), the Nodal Expansion Method (NEM), and the Nodal Collocation Method (NCM), used virtually in all neutronic diffusion codes, which give accurate results in structured meshes. However, the application of these methods in unstructured meshes to deal with complex geometries is not straightforward and it may cause problems of stability and convergence of the solution. By contrast, the Finite Element Method (FEM) and the Finite Volume Method (FVM) are easily applied to unstructured meshes. On the one hand, the FEM can be accurate for smoothly varying functions. On the other hand, the FVM is typically used in the transport equations due to the conservation of the transported quantity within the volume. In this paper, the FVM algorithm implemented in the ARB Partial Differential Equations solver has been used to discretize the neutron diffusion equation to obtain the matrices of the generalized eigenvalue problem, which has been solved by means of the SLEPc library., This work has been partially supported by the Spanish Ministerio de Ciencia e Innovacion under Projects ENE2011-22823 and ENE2012-34585, the Generalitat Valenciana under Projects PROMETEO/2010/039 and ACOMP/2013/237, and the Universitat Politecnica de Valencia under Project UPPTE/2012/118.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Development and validation of a one-dimensional solver in a CFD platform for boiling flows in bubbly regimes

  • Gomez-Zarzuela-Quel, Consuelo
  • Chiva Vicent, Sergio
  • Peña-Monferrer, Carlos
  • Miró Herrero, Rafael|||0000-0003-1012-0869
[EN] This paper presents a new one-dimensional solver for two-phase flow simulations where boiling is involved. The solver has been implemented within the OpenFOAM® platform. The basic formulation follows the Eulerian description of the Navier¿Stokes equations. Different closure equations for one-dimensional simulations are also included, as well as a subcooled boiling model in order to perform accurate computations of the mass and heat transfer between phases. In addition to the fluid, a domain is included in order to represent the solid structure, so the solver is able to solve conjugate heat transfer problems. Two different test cases are presented in this work, first a single-phase test case in order to verify the conjugate heat transfer, and then a case based on the Bartolomej international benchmark, which consists of a vertical pipe where the fluid runs upwards while it is heated. Transient calculation were performed, and the results were compared to the TRACE system code, and to the experimental data in the corresponding case. With this calculations, the capability of this new solver to simulate one-dimensional single-phase and two-phase flows including boiling is demonstrated. This work is a first step of a final objective, which consists in allowing a 1D¿3D coupling within the CFD platform, avoiding external links., This work has been partially supported by the Spanish Agencia Estatal de Investigacion [grant number BES-2013-064783], and the Spanish Ministerio de Economia Industria y Competitividad [project NUC-MULTPHYS ENE2012-34585].
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A multi-scale and multi-physics simulation methodology with the state-of-the-art tools for safety analysis in light water reactors applied to a turbine trip scenario (PART I)

  • Hidalga-García-Bermejo, Patricio
  • Abarca Giménez, Agustín
  • SEKHRI, ABDELKRIM
  • Miró Herrero, Rafael|||0000-0003-1012-0869
  • Verdú Martín, Gumersindo Jesús|||0000-0001-5098-080X
[EN] The simulation of transient events is a requirement in the evaluation of the safety of Nuclear Power Plants. The Nuclear Authority request the operators to report the prediction of the evolution of the corresponding safety variables using simulation codes and methodologies that have proved to be validated against real data, whether experiments or plant measurements. Moreover, these simulation codes are used in the engineering work that a Nuclear Power Plant needs for planning a competitive and safe operation strategy. The available resources in simulation tools make possible complex analysis that can be used to predict realistic results. The consequence is the opportunity of making a safe and cost-efficient evaluation of the safety margins. Operators can use these tools for licensing to the Nuclear Authority and for calculation support of the operation of the reactor in whichever considered case. This paper presents a methodology that takes advantage of different simulation tools to join the capabilities in the Best Estimate (BE) simulation of transients for Light Water Reactors. This methodology works in different steps to account all the physics using the proper scale in a multi-physics and multi-scale approach. An automatic tool manages the data pre- and post-processing the corresponding input and output files. The purpose is to simulate the transient case in a coarse mesh and generate the boundary conditions for a simulation in more detailed scale with a finer mesh in the next step. Therefore, this methodology works generating the corresponding nodal cross section data to be used in coupled 3D thermal-hydraulics and neutron kinetics simulations run with system codes. A channel-by-channel core model is used in order to identify the critical fuel channel. Finally, the boundary conditions of the critical fuel channel are loaded in a pin-by-pin thermal-hydraulic model to perform the definitive Safety Analysis of the target variable, that is selected by the user. The methodology presented in this paper, is applied to a real fast transient case, a Turbine Trip event of fuel cycle 18 in Kernkraftwerk Leibstadt, KKL. The results of each step of this methodology have been validated against the available plant data and the selected target safety variable, the Critical Power Ratio at pin level, has been code-to-code verified. The results show good agreement proving the effectivity of this methodology., The authors of this paper acknowledge the interest and economical and technical support of KKL to undertake the development of this project. This acknowledgement is extended to the collaboration of KKL in the research tasks by sharing plant measurements to validate the methodology and to use their software resources to generate useful data for the code-to-code verification.