Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 25
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Ni-CeO2/C Catalysts with Enhanced OSC for the WGS Reaction

  • Pastor-Pérez, Laura
  • Ramírez-Reina, Tomás
  • Ivanova, Svetlana
  • Centeno, Miguel Ángel
  • Odriozola, José Antonio
  • Sepulveda-Escribano, Antonio
In this work, the WGS performance of a conventional Ni/CeO2 bulk catalyst is compared to that of a carbon-supported Ni-CeO2 catalyst. The carbon-supported sample resulted to be much more active than the bulk one. The higher activity of the Ni-CeO2/C catalyst is associated to its oxygen storage capacity, a parameter that strongly influences the WGS behavior. The stability of the carbon-supported catalyst under realistic operation conditions is also a subject of this paper. In summary, our study represents an approach towards a new generation of Ni-ceria based catalyst for the pure hydrogen production via WGS. The dispersion of ceria nanoparticles on an activated carbon support drives to improved catalytic skills with a considerable reduction of the amount of ceria in the catalyst formulation., We acknowledge support by the CSIC Open Access Publication Initiative through its Unit of Information Resources for Research (URICI)., Financial support of Ministerio de Ciencia e Innovacion of Spain (Project MAT2010-21147) is gratefully acknowledged. L.P.P. acknowledges her grant BES-2011-0406508. The Spanish Ministerio de Economía y Competitividad (MINECO) is also acknowledged for the funding linked to the projects ENE2012-374301-C03-01 and ENE2013-47880-C3-2-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Operando DRIFTS-MS Study of WGS and rWGS Reaction on Biochar-Based Pt Catalysts: The Promotional Effect of Na

  • Santos, José L.
  • Bobadilla, Luis F.
  • Centeno, Miguel Ángel
  • Odriozola, José Antonio
Biochar-based Pt catalysts, unpromoted and Na-promoted, were prepared by an incipient wetness impregnation method and characterised by Inductively coupled plasma mass spoectrometry (ICP-MS) analysis, X-ray diffraction, N2 adsorption and transmission, and scanning electron microscopy. It was demonstrated that a sodium promoter modifies the acid-base properties of the support, altering the Pt-support interaction. An operando Diffuse reflectance infrared fourier transform spectroscopy-mass spectrometry (DRIFTS-MS) study was performed to gain insights into the reaction pathways and the mechanism of the Water-Gass-Shift (WGS) and the Reverse Water-Gass-Shift (rWGS) reactions. It was demonstrated that the addition of Na enhances the catalytic performance due to the changes induced by the alkali in the electronic structure of the Pt active sites. This effect favours the activation of H2O molecules during the WGS reaction and the dissociation of CO2 during the rWGS reaction, although it may also favour the consecutive CO methanation pathway., This research was funded by the Spanish Ministerio de Economía y Competitividad (MINECO) (ENE2013-47880-C3-2-R and ENE2017-82451-C3-3R), co-financed by FEDER funds from the European Union. J.L. Santos and L.F. Bobadilla also acknowledge MINECO for the PhD fellowship (BES-2014-068244) and the postdoctoral contract Juan de la Cierva-Incorporación (FJCI-2017-32128), respectively., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Impact of structured catalysts in amine oxidation under mild conditions

  • Santos, Jose Luis
  • Navarro, Pablo
  • Odriozola, José Antonio
  • Centeno, Miguel Ángel
  • Pavel, Octavian D.
  • Jurca, Bogdan
  • Parvulescu, Vasile I.
A structured graphene/graphite catalyst grown on a commercial austenitic stainless steel sheet providing a micromonolith was obtained by submitting the nude stainless steel structure to a carbon-rich atmosphere (first 300 mL/min of a reductive H/N (1:1) flow, then to 180 mL/min of a CH/H (1:5)) at high temperature (900 °C) for 2 h. The preparation procedure resulted in a homogenous surface coated with a carbon-rich film as observed by EDX and SEM images. Further characterizations by Raman spectroscopy revealed characteristic Raman lines of graphene and crystalline graphite disposed in a hierarchical organization. The disposal of the obtained surface layers was also confirmed by grazing incidence X-ray diffraction. Besides this, XRD indicated the overlapping diffraction lines of graphite, cementite and MC carbides. The graphene nature of the outermost layer was also confirmed by XPS. The catalytic behavior of the structured graphene/graphite catalyst was evaluated in the selective oxidation of heptylamine. At 200 °C it afforded a total conversion with a combined selectivity in heptanonitrile and N-heptylidene-heptylamine of 67% (10% heptanonitrile) that corresponds indeed to a very efficient system in the absence of any metal. Kinetic experiments with the scope to calculate the activation energies were also performed., The authors gratefully acknowledge the financial support from the 275/2011PN-II-ID-PCE-2011-3-0060 project and from Spanish Ministerio de Economía y Competitividad (MINECO) project ENE2013-47880-C3-2-R, co-financed by FEDER funds from the European Union. J.L. Santos also acknowledges the Spanish Ministerio de Economía y Competitividad for his predoctoral fellowship (BES-2014-068244).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Fischer–Tropsch Synthesis Over Zr-Promoted Co/γ-Al2O3 Catalysts

  • Barrientos, Javier
  • Garcilaso, Victoria
  • Venezia, Baldassarre
  • Aho, Atte
  • Odriozola, José Antonio
  • Boutonnet, Megali
  • Järås, Sven
Two Zr-modified alumina supports were synthetized containing the same amount of Zr but a different distribution of this modifier over the alumina surface. These supports, together with the unmodified alumina carrier, were used to prepare three cobalt-based catalysts which were characterized and tested under relevant Fischer–Tropsch conditions. The three catalysts presented very similar porosity and cobalt dispersion. The addition of Zr nor its distribution enhanced the catalyst reducibility. The catalyst activity was superior when using a carrier consisting of large ZrO islands over the alumina surface. The use of a carrier with a homogeneous Zr distribution had however, a detrimental effect. Moreover, a faster initial deactivation rate was observed for the Zr-promoted catalysts, fact that may explain this contradictory effect of Zr on activity. Finally, the addition of Zr showed a clear enhancement of the selectivity to long chain hydrocarbons and ethylene, especially when Zr was well dispersed., The research leading to these results has received funding from the European Union Seventh Framework Programme (FP7/2013) under Grant Agreement No. 308733. The authors are thankful to the Spanish Ministerio de Economía y Competitividad—MINECO (references: BES-2013-062806, ENE2013-47880-C3-2-R and ENE2015-66975-C3-2-R) co-financed by FEDER funds from the European Union.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Synthesis of Pd-Al/biomorphic carbon catalysts using cellulose as carbon precursor

  • Cazaña, F.
  • Galetti, A.
  • Meyer, C.
  • Sebastián, Víctor
  • Centeno, Miguel Ángel
  • Romeo, E.
  • Monzón, A.
This work presents the results obtained with novel Pd and Pd-Al catalysts supported on carbon, which have been prepared using a biomorphic mineralization technique. The catalyst synthesis procedure includes a stage of thermal decomposition under reductive atmosphere of cellulose previously impregnated with the metallic precursors. We have studied the influence of the temperature and time of decomposition, and of the Al precursor addition, on the textural and catalytic properties. The characterisation results indicate that the preparation method used leads to the formation of carbonaceous supports with a high microporosity (up to 97% micropore volume) and values of the BET surface up to 470 m/g while maintaining the original external structure. The use of low temperatures (ca. 600 °C) during the decomposition step allows the preparation of highly dispersed catalysts with narrow Pd particle size distributions. However, the thermal decomposition at elevated temperatures (ca. 800 °C) increases the Pd particle size due to the sintering of the metallic phase. This phenomenon is augmented with the decomposition time and is not affected by the presence of Al. Consequently, the catalytic activity of these materials in cyclohexene hydrogenation is strongly affected by the operational conditions used during the thermal decomposition step. Unexpectedly, the more sintered catalysts, i.e. those prepared at 800 °C, show the highest activity. According to the characterization results, this fact can be explained considering that the smaller Pd particles obtained after preparation at e.g. 600 °C are quite inactive because they are confined in the internal structure of the micropores of the support and/or embedded inside the carbon matrix. In contrast, after decomposition at 800 °C, the larger Pd particles formed are placed at the external surface of the catalyst, being accessible to the reactants. In addition, for the specific conditions under which the Pd is accessible, the presence of Al favours the cyclohexene conversion due to the enhancement of the adsorption on the Pd surface as a consequence of a charge transfer phenomenon. These results can serve as a guideline for the preparation of these catalysts based on raw lignocellulosic materials in order to maximize their catalytic performance., The authors acknowledge financial support from MINECO (Madrid, Spain)-FEDER, Projects CTQ2010-16132 and ENE2013-47880-C3-1-R.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Hydrodeoxygenation of vanillin over noble metal catalyst supported on biochars: Part II: Catalytic behaviour

  • Santos Muñoz, José Luis
  • Mäki-Arvela, Päivi
  • Wärnå, Johan
  • Monzón, Antonio
  • Centeno, Miguel Ángel
  • Murzin, Dmtry Yu.
Vanillin hydrodeoxygenation was investigated using noble metal (Pd, Au, Ru) supported on active carbon prepared from waste derived biochars, which were produced via pyrolysis in CO2 atmosphere. Chemical activation with ZnCl2 and HNO3 was also used in the preparation of active carbon to enhance the specific surface area and demineralize material, respectively. Both fresh and spent catalysts were characterized with X-ray diffraction, DRIFTS, zeta potential measurement and HR-TEM. The highest selectivity to p-creosol, 92 % selectivity at complete vanillin conversion after 3 h was obtained in vanillin hydrodeoxygenation at 100 °C under 30 bar in hydrogen in water with Pd/C catalyst prepared via pyrolysis under CO2 from wine waste and using ZnCl2 as a chemical activation agent. Hydrodeoxygenation activity increased with increasing metal dispersion. A kinetic model including adsorption of vanillin described well the experimental data., Financial support for this work has been obtained from the Spanish Ministerio de Economía y Competitividad (MINECO) (Grants ENE2013-47880-C3-2-R, ENE2017-82451-C3-3-R and ENE2017-82451-C3-1-R) co-financed by FEDER funds from the European Union. J.L. Santos also acknowledges the MINECO for his pre-doctoral fellowship (BES-2014-068244) and the mobility fellowship (EEBB-I-17-11979)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Metal catalysts supported on biochars: Part I synthesis and characterization

  • Santos, José Luis
  • Mäki-Arvela, Päivi
  • Monzón, Antonio
  • Murzin, Dmtry Yu.
  • Centeno, Miguel Ángel
In the current study, synthesis and detailed characterization of cellulose biochars as a waste biomass model component and vine shoot biochars as a real waste biomass catalyst was performed. Although initially biochars exhibit poor textural properties, a simple activation process can make them much more suitable as a catalyst supports. A combination of physical (CO2) and chemical activation (ZnCl2) was evaluated. The characterization results indicated that the surface area and pore volume of the biochars have increased significantly by chemical activation treatment with ZnCl2. A series of metal catalysts (Pd, Au and Ru) supported on biochars was prepared and characterized. The prepared materials represent a set of noble metal catalysts supported on biochars with different textural and surface properties, which can be used to evaluate the catalytic role of the active phase and carbon support nature in catalytic reactions of interest, such as hydrodeoxygenation, described in the part II., Financial support for this work has been obtained from the Spanish Ministerio de Economía y Competitividad (MINECO) (Grants ENE2013-47880-C3-2-R, ENE2017-82451-C3-3-R and ENE2017-82451-C3-1-R) co-financed by FEDER funds from the European Union. J.L. Santos also acknowledges the MINECO for his predoctoral fellowship (BES-2014-068244) and the mobility fellowship (EEBB-I-17-11979)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Use of Ni catalysts supported on biomorphic carbon derived from lignocellulosic biomass residues in the decomposition of methane

  • Azuara, Manuel
  • Latorre, Nieves
  • Villacampa, José I.
  • Sebastián, Víctor
  • Cazaña, Fernando
  • Romeo, Eva
  • Monzón, Antonio
In this work, we present the results of production of carbonaceous nanomaterials by decomposition of methane on a catalyst of Ni supported on a Biomorphic Carbon. The catalyst was prepared by thermal decomposition in a reductive atmosphere of vine shoots previously impregnated with the Ni precursor. In order to optimize the reaction productivity and selectivity, the effect of the main operational conditions (reaction temperature and feed composition) has been studied in a thermobalance. The main textural properties, BET area of 63 m2/g and 56% of microporosity, of the catalyst synthesized indicates that these materials are suitable for gas-phase reactions even in harsh conditions. Thus, the catalyst has proved to be active in the synthesis of carbon nanofibers and graphene related materials at elevated temperatures. The productivity, type, and quality of the carbonaceous nanomaterials obtained are deeply dependent on the operating conditions during the reaction. As an important fact, is has been obtained that the reaction temperature strongly affects the type of the nanomaterial produced. Thus, it is produced CNFs of bamboo type at temperatures until 850°C. Above this critical temperature, it is mainly obtained nanolayers of graphitic nature. The characterization results indicate that the highest quality graphenic materials were obtained operating at 950°C with 14.3% of CH4 and 14.3% of H2. The kinetic model used to analyze the experimental data is based on the more relevant stages of the mechanism of reaction., We acknowledge financial support from MINECO (Madrid, Spain) FEDER, Projects ENE2017-82451-C3 y ENE2013-47880-C3., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Biochar production through slow pyrolysis of different biomass materials: Seeking the best operating conditions

  • Manyà, Joan J.
  • Azuara, Manuel
  • Manso, José A.
The effect of three operating parameters (peak temperature, pressure, and pyrolysis atmosphere) during the slow pyrolysis of three biomass sources (corn stover, vine shoots, and two-phase olive mill waste) was extensively analyzed. A 2-level full factorial design of experiments was adopted to assess the effect of the above-mentioned factors on the potential stability of biochar as well as the yields of the main pyrolysis products. To evaluate the effect of the biomass feedstock, the design was divided into three blocks (one per biomass feedstock). Results from the statistical analyses indicated that the properties of biochar related to its potential stability were mainly affected by the peak temperature and, to a lesser extent, the biomass feedstock. A significant increase in the yield of produced gas was observed when pressure was raised. This increase in the total gas yield was in part due to a higher release of CO, CH4, and H2. Using a pyrolysis atmosphere of CO2 (instead of N2) did not result in any remarkable change in neither the distribution of the pyrolysis products nor the potential stability of biochar. However, when CO2 was used as carrier gas, a significant increase in the yield of CO, at the expense of produced CO2, was observed. The findings reported herein suggest that processing biomass through pressurized slow pyrolysis under CO2 atmosphere is interesting to simultaneously obtain two valuable products: a biochar with an appropriate carbon sequestration potential, and a produced gas with an appropriate composition for energy recovery purposes., The authors wish to acknowl nish MINECO-DGI (Project ENE2013-47880-C3-1-R). JJM also express his gratitude to the Aragon Government (GPT group) and the European Social Fund for additional financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effect of the operating conditions on the growth of carbonaceous nanomaterials over stainless steel foams. Kinetic and characterization studies

  • Latorre, Nieves
  • Cazaña, Fernando
  • Sebastián, Víctor
  • Royo, Carlos J.
  • Romeo, Eva
  • Monzón, Antonio
This work is an advance on the development of structured catalytic reactors. Here, we present the results of the effect of the main operational variables (reaction temperature, % H2 and % C2H6) on the kinetics of carbonaceous nanomaterials (CNMs) formation by catalytic decomposition of ethane over stainless steel foams. Some of the main drawback problems that occur during the operation of chemical structured reactors are related to the preparation of long term stable coatings. The washcoating is the most used technique to deposit the catalytic layer over the substrate. The application of this procedure is quite complex in the case of geometries such as foams or cloths. In the case of the deposition of layers of carbonaceous nanomaterials, an alternative route, avoiding the washcoating, is their direct growth by catalytic decomposition of light hydrocarbons over the surface of the metallic substrate. In the case of structured steel foams, the substrate already contains the catalytic active phases for this reaction, like Fe and Ni, among of the minor components (Cr, Mn, Mo) that can act as promotors/stabilizers., The nanomaterials obtained after reaction were characterized by Raman spectroscopy, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The characterization results indicate that there is a maximum, obtained at ca. 900 °C, 33.3 % of C2H6 and 1.7 % of H2, in the quality of the carbonaceous nanomaterials grown. Under these conditions, the CNMs consist mainly of few layer graphene (FLG) and graphite nanolayers (GNL) encapsulating the metallic nanoparticles. In addition, the kinetic results indicate the existence of another optimum, at ca. 800 °C, 33.3 % of C2H6 and 1.7 % of H2, in the productivity to the carbonaceous nanomaterials. The existence of these optimums is due to the driving force for the diffusion of the carbon atoms through the Fe-Ni nanoparticles (NPs) obtained at high temperatures (e. g. above 800 °C) caused by the competence between two opposite phenomena: the increase of the rate of carbon diffusion through the metallic nanoparticles of Fe-Ni and the deactivation of these nanoparticles. The deactivation is the consequence of the encapsulation and reconstruction of the nanoparticles during the formation of the several types of CNMs. The evolution of the carbon mass during the reaction time was analyzed using a phenomenological kinetic model that takes into account the main stages involved during the formation of carbonaceous nanomaterials: hydrocarbon decomposition, carburization, diffusion, precipitation and deactivation. The results obtained from the kinetic model, along with the characterization results, enable quantify the influence of the operating variables on each stage of the carbonaceous nanomaterial formation and therefore open the way to optimize the process., The authors acknowledge financial support from MINECO (Madrid, Spain) FEDER, Project ENE2013-47880-C3-1-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effects of pressure and the addition of a rejected material from municipal waste composting on the pyrolysis of two-phase olive mill waste

  • Manyà, Joan J.
  • Alvira, Darío
  • Azuara, Manuel
  • Bernin, Diana
  • Hedin, Niklas
This work examines the effect of the absolute pressure (0.1 or 1.0 MPa) and the addition of a high-ash rejected material from municipal solid waste (MSW) composting (RC) on the slow pyrolysis of two-phase olive mill waste (OW). The experiments were conducted in a batch pyrolysis system using an initial mass of 750 g of feedstock. Three types of initial materials were tested: the OW alone, a mixture of OW and pure additives (5 wt % K2CO3 and 5 wt % CaO), and a mixture of OW and RC (10 wt %). For the OW without any additive, an increased pressure led to a market increase in the carbonization efficiency (i.e., fixed carbon yield). At atmospheric pressure, the addition of either additives (CaO + K2CO3) or RC led to important changes in the pyrolysis behavior as a result of the catalytic role of the alkali and alkaline earth metals (AAEMs). However, this catalytic effect, which is translated into an enhancement of the decomposition of both the hemicellulose and cellulose fractions, was not observed at 1.0 MPa. The potential stability of all of the produced biochars appeared to be very high, given the results obtained from both proximate and ultimate analyses. This high stability was confirmed by 13C and 1H solid-state nuclear magnetic resonance, which showed that the carbon contained in the biochars was composed mainly or entirely of highly condensed aromatic structures. However, the highest values of stable C (Edinburgh stability tool) and R50,x (recalcitrance index) were obtained for biochars produced from the OW + RC mixtures at any pressure. In summary, the addition of the rejected material from MSW composting appears to be a very cost-effective measure to obtain a potentially high-stable biochar, even at atmospheric pressure., The authors acknowledge financial support from the Spanish MINECO-DGI (Project ENE2013-47880-C3-1-R). Joan J. Manyà also express his gratitude to the Aragon Government (GPT Group) and the European Social Fund for additional financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Influence of pressure and temperature on key physicochemical properties of corn stover-derived biochar

  • Azuara, Manuel
  • Baguer, Bárbara
  • Villacampa, José I.
  • Hedin, Niklas
  • Manyà, Joan J.
This study focuses on analyzing the effect of both the peak temperature and pressure on the properties of biochar produced through slow pyrolysis of corn stover, which is a common agricultural waste that currently has little or no value. The pyrolysis experiments were carried out in a fixed-bed reactor at different peak temperatures (400, 525 and 650 °C) and absolute pressures (0.1, 0.85 and 1.6 MPa). The inert mass flow rate (at NTP conditions) was adjusted in each test to keep the gas residence time constant within the reactor. The as-received corn stover was pyrolyzed into a biochar without any physical pre-treatment as a way to reduce the operating costs. The properties of biochars showed that high peak temperature led to high fixed-carbon contents, high aromaticity and low molar H:C and O:C ratios; whereas a high pressure only resulted in a further decrease in the O:C ratio and a further increase in the fixed-carbon content. Increasing the operating pressure also resulted in a higher production of pyrolysis gas at the expense of water formation., The authors wish to acknowledge financial support from the Spanish MINECO-DGI (Project ENE2013-47880-C3-1-R). JJM also express his gratitude to the Aragon Government (GPT group) and the European Social Fund for additional financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Pyrolysis and char reactivity of a poor-quality refuse-derived fuel (RDF) from municipal solid waste

  • Manyà, Joan J.
  • García-Ceballos, Fernando
  • Azuara, Manuel
  • Latorre, Nieves
  • Royo, Carlos J.
The present study focuses on analyzing the pyrolysis and combustion behaviors of a refuse-derived fuel (RDF), which is generated in a MSW treatment plant located in Zaragoza (Spain). Pyrolysis experiments were carried out in a TGA apparatus and a fixed-bed reactor at different peak temperatures (400 and 600 °C) and heating rates (5 and 40 °C min− 1). The reactivity towards oxygen of produced chars was also measured in the same TGA device at a heating rate of 10 °C min− 1 and a final temperature of 800 °C. Pyrolysis results were significantly affected by peak temperature and heating rate. The found effect of peak temperature on char and fixed-carbon yields as well as on measured properties (H:C and O:C ratios, BET surface area and average pore diameter) was in agreement with previous studies. However, the effect of heating rate, especially on the release rate of volatiles, could be explained by a change in the pyrolysis reaction scheme. The RDF-derived chars obtained at the highest heating rate showed a higher reactivity in air. In addition, an increase in peak temperature also led to a higher reactivity. This result can indicate that the carbon present in the RDF-derived char is dispersed within an ash matrix containing a high number of active sites, the distribution of which could be improved when heating rate (and, to a lesser extent, peak temperature) is increased. The addition of 10 wt.% RDF to two-phase olive mill waste prior to slow pyrolysis led to an apparent increase in the carbonization efficiency as well as to an enhancement of the resultant char's reactivity in air., The authors wish to acknowledge the financial support from the Spanish MINECO-DGI (Project ENE2013-47880-C3-1-R). JJM also express his gratitude to the Aragon Government (GPT group) and the European Social Fund for additional financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Study on the effects of using a carbon dioxide atmosphere on the properties of vine shoots-derived biochar

  • Azuara, Manuel
  • Sáiz, Eva
  • Manso, José A.
  • García-Ramos, F. Javier
  • Manyà, Joan J.
This study analyzes the effects of using a different atmosphere (pure N2 or pure CO2) at two levels of absolute pressure (0.1 and 1.1 MPa) on the pyrolysis of vine shoots at a constant peak temperature of 600 °C. Recycling CO2 from residual flue gases into the pyrolysis process may be economically beneficial, since CO2 can replace the use of an expensive N2 environment. In addition, the use of a moderate pressure (e.g., 1.1 MPa) can result in higher carbonization efficiencies and an improvement in the pyrolysis gas (in terms of yield and composition). Results from our study suggest that the use of CO2 instead of N2 as pyrolysis environment led to similar carbonization efficiencies (i.e., fixed-carbon yields) and mass yields of biochar. The chemical properties related to the potential stability of biochar (i.e., fixed-carbon content and molar H:C and O:C ratios) were very similar for both pyrolysis atmospheres. Under an atmosphere of CO2, the yield of produced CO2 was drastically decreased at the expense of an increase in the yield of CO, probably as a consequence of the promotion of the reverse Boudouard reaction, especially at high pressure. The enhanced reverse Boudouard reaction can also explain the relatively high BET specific surface area and the macro-porosity development observed for the biochar produced under a CO2 environment at 1.1 MPa. In summary, the pressurized pyrolysis of biomass under an atmosphere of CO2 appears as a very interesting route to produce highly stable and porous biochars and simultaneously improving the yield of CO., The authors wish to acknowledge financial support from the Spanish MINECO-DGI (Project ENE2013-47880-C3-1-R). JJM also express his gratitude to the Aragon Government (GPT group) and the European Social Fund for additional financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Synthesis of graphenic nanomaterials by decomposition of methane on a Ni-Cu/biomorphic carbon catalyst. Kinetic and characterization results

  • Cazaña, Fernando
  • Latorre, Nieves
  • Tarifa, Pilar
  • Labarta, J.
  • Romeo, Eva
  • Monzón, Antonio
This work addresses the preparation and application of the synthesis of graphene in Ni-Cu catalysts supported on carbonaceous materials. The catalysts have been prepared by a biomorphic mineralization technique which involves the thermal decomposition, under reductive atmosphere, of commercial cellulose previously impregnated with the metallic precursors. The characterization results indicate that the preparation method leads to the formation of carbonaceous supports with a moderate microporosity (ca. 33% pore volume) and adequate surface area (343 m2/g), maintaining the original external texture. The catalytic performance of these materials was previously tested in liquid phase reactions (Zampieri et al., 2007 [7]). In order to extend the use of these catalysts, in this work we present a study corresponding to a gas phase reaction: the synthesis of graphenic nanomaterials by catalytic decomposition of methane (CDM). The influence of the reaction temperature and of the feed composition (i.e.%CH4 and%H2) has been studied. The graphenic nanomaterials obtained after reaction were characterized by nitrogen adsorption-desorption isotherms, Raman spectroscopy and transmission electron microscopy (TEM). The results indicate that the carbonaceous nanomaterial with the highest quality is obtained operating at 950 °C and feeding 28.6% of CH4 and 14.3% of H2. The evolution of the carbon mass during the reaction time was analysed using a phenomenological kinetic model that takes into account the main stages involved during the formation of carbonaceous nanomaterials (NCMs). The results obtained from the kinetic model along with the characterization results enable the influence of the operating variables on each stage of the carbonaceous nanomaterial formation to be discerned., The authors acknowledge financial support from MINECO (Madrid, Spain) FEDER, Project ENE2013-47880-C3-1-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Ultra-microporous adsorbents prepared from vine shoots-derived biochar with high CO2 uptake and CO2/N2 selectivity

  • Manyà, Joan J.
  • González, Belén
  • Azuara, Manuel
  • Arner, Gabriel
There is a growing interest in developing renewable biomass-based adsorbents to be used in numerous applications, including CO2 capture in postcombustion conditions. In the present study, several activated carbons (ACs) were produced from vine shoots-derived biochar through both physical and chemical activation using CO2 and KOH, respectively. The performance of these ACs was tested in terms of CO2 uptake capacity at an absolute pressure of 15 kPa and at different temperatures (0, 25, and 75 °C), apparent selectivity towards CO2 over N2, and isosteric heat of adsorption. At 25 °C, the chemically ACs with KOH impregnation exhibited the highest CO2 adsorption capacity, which was similar or even higher than those recently reported for a number of carbon-based adsorbents. However, the AC prepared through physical activation with CO2 at 800 °C and a soaking time of 1 h appears as the most promising adsorbent analyzed here, due to its higher CO2 uptake capacity and adsorption rate at relatively high temperature (75 °C), its relatively high selectivity at this temperature, and its apparently low energy demand for regeneration. Given that physical activation with CO2 is more feasible at industrial scale than chemical activation using corrosive alkalis, the results reported here are encouraging for further development of vine shoots-derived adsorbents., The authors wish to acknowledge financial support from the Spanish MINECO-DGI (Project ENE2013-47880-C3-1-R). JJM also express his gratitude to the Aragon Government (GPT group) and the European Social Fund for additional financial support., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Pyrolysis and char reactivity of a poor-quality refuse-derived fuel (RDF) from municipal solid waste

  • Manyà, J.J.
  • García-Ceballos, F.
  • Azuara, M.
  • Latorre, N.
  • Royo, C.
The present study focuses on analyzing the pyrolysis and combustion behaviors of a refuse-derived fuel (RDF), which is generated in a MSW treatment plant located in Zaragoza (Spain). Pyrolysis experiments were carried out in a TGA apparatus and a fixed-bed reactor at different peak temperatures (400 and 600 °C) and heating rates (5 and 40 °C min- 1). The reactivity towards oxygen of produced chars was also measured in the same TGA device at a heating rate of 10 °C min- 1 and a final temperature of 800 °C. Pyrolysis results were significantly affected by peak temperature and heating rate. The found effect of peak temperature on char and fixed-carbon yields as well as on measured properties (H:C and O:C ratios, BET surface area and average pore diameter) was in agreement with previous studies. However, the effect of heating rate, especially on the release rate of volatiles, could be explained by a change in the pyrolysis reaction scheme. The RDF-derived chars obtained at the highest heating rate showed a higher reactivity in air. In addition, an increase in peak temperature also led to a higher reactivity. This result can indicate that the carbon present in the RDF-derived char is dispersed within an ash matrix containing a high number of active sites, the distribution of which could be improved when heating rate (and, to a lesser extent, peak temperature) is increased. The addition of 10 wt.% RDF to two-phase olive mill waste prior to slow pyrolysis led to an apparent increase in the carbonization efficiency as well as to an enhancement of the resultant char''s reactivity in air.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Synthesis of graphenic nanomaterials by decomposition of methane on a Ni-Cu/biomorphic carbon catalyst. Kinetic and characterization results

  • Cazaña, F.
  • Latorre, N.
  • Tarifa, P.
  • Labarta, J.
  • Romeo, E.
  • Monzón, A.
This work addresses the preparation and application of the synthesis of graphene in Ni-Cu catalysts supported on carbonaceous materials. The catalysts have been prepared by a biomorphic mineralization technique which involves the thermal decomposition, under reductive atmosphere, of commercial cellulose previously impregnated with the metallic precursors. The characterization results indicate that the preparation method leads to the formation of carbonaceous supports with a moderate microporosity (ca. 33% pore volume) and adequate surface area (343 m2/g), maintaining the original external texture. The catalytic performance of these materials was previously tested in liquid phase reactions (Zampieri et al., 2007 [7]). In order to extend the use of these catalysts, in this work we present a study corresponding to a gas phase reaction: the synthesis of graphenic nanomaterials by catalytic decomposition of methane (CDM). The influence of the reaction temperature and of the feed composition (i.e.%CH4 and%H2) has been studied. The graphenic nanomaterials obtained after reaction were characterized by nitrogen adsorption-desorption isotherms, Raman spectroscopy and transmission electron microscopy (TEM). The results indicate that the carbonaceous nanomaterial with the highest quality is obtained operating at 950 °C and feeding 28.6% of CH4 and 14.3% of H2. The evolution of the carbon mass during the reaction time was analysed using a phenomenological kinetic model that takes into account the main stages involved during the formation of carbonaceous nanomaterials (NCMs). The results obtained from the kinetic model along with the characterization results enable the influence of the operating variables on each stage of the carbonaceous nanomaterial formation to be discerned.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Growth of carbonaceous nanomaterials over stainless steel foams. Effect of activation temperature

  • Latorre, N.
  • Cazaña, F.
  • Sebastian, V.
  • Royo, C.
  • Romeo, E.
  • Centeno, M. A.
  • Monzón, A.
Some of the problems that occur during the operation of chemical reactors based of structured catalytic substrates, as monoliths, foams, membranes, cloths, fibres and other systems, are related to the preparation of long term stable coatings. Frequently, the deposition of the catalytic layer is carried out by washcoating, requiring this step a cautious attention, especially in the case of complex geometries, like of that of foams or cloths. In the case of the deposition of layers of carbonaceous materials (CNMs), an alternative route, avoiding the washcoating, it is their direct growth by catalytic decomposition light hydrocarbons (also called CCVD), over the surface of the metallic substrate. In this case, if the metallic substrate is of stainless steel, it already contains the catalytic active phases like Fe and Ni. In order to optimize the process of CNMs growth over structured metallic substrates, we are studying the effect of the main operational variables of the ethane decomposition reaction on stainless steel foams. In this contribution we present a study of the influence of the temperature of the activation (oxidation and reduction) stage on the type and morphology of the carbonaceous materials formed. The results obtained allow us to determine the optimal operating conditions to maximize the amount and the selectivity of the process to obtain a given type of CNM.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Influence of pressure and temperature on key physicochemical properties of corn stover-derived biochar

  • Azuara, M.
  • Baguer, B.
  • Villacampa, J. I.
  • Hedin, N.
  • Manyà, J. J.
This study focuses on analyzing the effect of both the peak temperature and pressure on the properties of biochar produced through slow pyrolysis of corn stover, which is a common agricultural waste that currently has little or no value. The pyrolysis experiments were carried out in a fixed-bed reactor at different peak temperatures (400, 525 and 650 °C) and absolute pressures (0.1, 0.85 and 1.6 MPa). The inert mass flow rate (at NTP conditions) was adjusted in each test to keep the gas residence time constant within the reactor. The as-received corn stover was pyrolyzed into a biochar without any physical pre-treatment as a way to reduce the operating costs. The properties of biochars showed that high peak temperature led to high fixed-carbon contents, high aromaticity and low molar H:C and O:C ratios; whereas a high pressure only resulted in a further decrease in the O:C ratio and a further increase in the fixed-carbon content. Increasing the operating pressure also resulted in a higher production of pyrolysis gas at the expense of water formation.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Effects of Pressure and the Addition of a Rejected Material from Municipal Waste Composting on the Pyrolysis of Two-Phase Olive Mill Waste

  • Manyà, J. J.
  • Alvira, D.
  • Azuara, M.
  • Bernin, D.
  • Hedin, N.
This work examines the effect of the absolute pressure (0.1 or 1.0 MPa) and the addition of a high-ash rejected material from municipal solid waste (MSW) composting (RC) on the slow pyrolysis of two-phase olive mill waste (OW). The experiments were conducted in a batch pyrolysis system using an initial mass of 750 g of feedstock. Three types of initial materials were tested: the OW alone, a mixture of OW and pure additives (5 wt % K2CO3 and 5 wt % CaO), and a mixture of OW and RC (10 wt %). For the OW without any additive, an increased pressure led to a market increase in the carbonization efficiency (i.e., fixed carbon yield). At atmospheric pressure, the addition of either additives (CaO + K2CO3) or RC led to important changes in the pyrolysis behavior as a result of the catalytic role of the alkali and alkaline earth metals (AAEMs). However, this catalytic effect, which is translated into an enhancement of the decomposition of both the hemicellulose and cellulose fractions, was not observed at 1.0 MPa. The potential stability of all of the produced biochars appeared to be very high, given the results obtained from both proximate and ultimate analyses. This high stability was confirmed by 13C and 1H solid-state nuclear magnetic resonance, which showed that the carbon contained in the biochars was composed mainly or entirely of highly condensed aromatic structures. However, the highest values of stable C (Edinburgh stability tool) and R50, x (recalcitrance index) were obtained for biochars produced from the OW + RC mixtures at any pressure. In summary, the addition of the rejected material from MSW composting appears to be a very cost-effective measure to obtain a potentially high-stable biochar, even at atmospheric pressure.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Study on the effects of using a carbon dioxide atmosphere on the properties of vine shoots-derived biochar

  • Azuara, M.
  • Sáiz, E.
  • Manso, J. A.
  • García-Ramos, F. J.
  • Manyà, J. J.
This study analyzes the effects of using a different atmosphere (pure N2 or pure CO2) at two levels of absolute pressure (0.1 and 1.1 MPa) on the pyrolysis of vine shoots at a constant peak temperature of 600 °C. Recycling CO2 from residual flue gases into the pyrolysis process may be economically beneficial, since CO2 can replace the use of an expensive N2 environment. In addition, the use of a moderate pressure (e.g., 1.1 MPa) can result in higher carbonization efficiencies and an improvement in the pyrolysis gas (in terms of yield and composition). Results from our study suggest that the use of CO2 instead of N2 as pyrolysis environment led to similar carbonization efficiencies (i.e., fixed-carbon yields) and mass yields of biochar. The chemical properties related to the potential stability of biochar (i.e., fixed-carbon content and molar H:C and O:C ratios) were very similar for both pyrolysis atmospheres. Under an atmosphere of CO2, the yield of produced CO2 was drastically decreased at the expense of an increase in the yield of CO, probably as a consequence of the promotion of the reverse Boudouard reaction, especially at high pressure. The enhanced reverse Boudouard reaction can also explain the relatively high BET specific surface area and the macro-porosity development observed for the biochar produced under a CO2 environment at 1.1 MPa. In summary, the pressurized pyrolysis of biomass under an atmosphere of CO2 appears as a very interesting route to produce highly stable and porous biochars and simultaneously improving the yield of CO.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Ultra-microporous adsorbents prepared from vine shoots-derived biochar with high CO2 uptake and CO2/N2 selectivity

  • Manyà, J.J.
  • González, B.
  • Azuara, M.
  • Arner, G.
There is a growing interest in developing renewable biomass-based adsorbents to be used in numerous applications, including CO2 capture in postcombustion conditions. In the present study, several activated carbons (ACs) were produced from vine shoots-derived biochar through both physical and chemical activation using CO2 and KOH, respectively. The performance of these ACs was tested in terms of CO2 uptake capacity at an absolute pressure of 15 kPa and at different temperatures (0, 25, and 75 °C), apparent selectivity towards CO2 over N2, and isosteric heat of adsorption. At 25 °C, the chemically ACs with KOH impregnation exhibited the highest CO2 adsorption capacity, which was similar or even higher than those recently reported for a number of carbon-based adsorbents. However, the AC prepared through physical activation with CO2 at 800 °C and a soaking time of 1 h appears as the most promising adsorbent analyzed here, due to its higher CO2 uptake capacity and adsorption rate at relatively high temperature (75 °C), its relatively high selectivity at this temperature, and its apparently low energy demand for regeneration. Given that physical activation with CO2 is more feasible at industrial scale than chemical activation using corrosive alkalis, the results reported here are encouraging for further development of vine shoots-derived adsorbents.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Use of ni catalysts supported on biomorphic carbon derived from lignocellulosic biomass residues in the decomposition of methane

  • Azuara, Manuel
  • Latorre, Nieves
  • Villacampa, José I
  • Sabastián, Víctor
  • Cazaña, Fernando
  • Romeo, Eva
  • Monzón, Antonio
In this work, we present the results of production of carbonaceous nanomaterials by decomposition of methane on a catalyst of Ni supported on a Biomorphic Carbon. The catalyst was prepared by thermal decomposition in a reductive atmosphere of vine shoots previously impregnated with the Ni precursor. In order to optimize the reaction productivity and selectivity, the effect of the main operational conditions (reaction temperature and feed composition) has been studied in a thermobalance. The main textural properties, BET area of 63 m(2)/g and 56% of microporosity, of the catalyst synthesized indicates that these materials are suitable for gas-phase reactions even in harsh conditions. Thus, the catalyst has proved to be active in the synthesis of carbon nanofibers and graphene related materials at elevated temperatures. The productivity, type, and quality of the carbonaceous nanomaterials obtained are deeply dependent on the operating conditions during the reaction. As an important fact, is has been obtained that the reaction temperature strongly affects the type of the nanomaterial produced. Thus, it is produced CNFs of bamboo type at temperatures until 850 degrees C. Above this critical temperature, it is mainly obtained nanolayers of graphitic nature. The characterization results indicate that the highest quality graphenic materials were obtained operating at 950 degrees C with 14.3% of CH4 and 14.3% of H-2. The kinetic model used to analyze the experimental data is based on the more relevant stages of the mechanism of reaction.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Biochar production through slow pyrolysis of different biomass materials: Seeking the best operating conditions

  • Manyà, Joan J.
  • Azuara, Manuel
  • Manso, José A.
The effect of three operating parameters (peak temperature, pressure, and pyrolysis atmosphere) during the slow pyrolysis of three biomass sources (corn stover, vine shoots, and two-phase olive mill waste) was extensively analyzed. A 2-level full factorial design of experiments was adopted to assess the effect of the above-mentioned factors on the potential stability of biochar as well as the yields of the main pyrolysis products. To evaluate the effect of the biomass feedstock, the design was divided into three blocks (one per biomass feedstock). Results from the statistical analyses indicated that the properties of biochar related to its potential stability were mainly affected by the peak temperature and, to a lesser extent, the biomass feedstock. A significant increase in the yield of produced gas was observed when pressure was raised. This increase in the total gas yield was in part due to a higher release of CO, CH4, and H2. Using a pyrolysis atmosphere of CO2 (instead of N2) did not result in any remarkable change in neither the distribution of the pyrolysis products nor the potential stability of biochar. However, when CO2 was used as carrier gas, a significant increase in the yield of CO, at the expense of produced CO2, was observed. The findings reported herein suggest that processing biomass through pressurized slow pyrolysis under CO2 atmosphere is interesting to simultaneously obtain two valuable products: a biochar with an appropriate carbon sequestration potential, and a produced gas with an appropriate composition for energy recovery purposes.