Skip to main content

APROVECHAMIENTO DE BIOMASA Y PRODUCCION SOSTENIBLE DE ENERGIA MEDIANTE (FOTO)CATALIZADORES Y REACTORES ESTRUCTURADOS BASADOS EN MATERIALES CARBONOSOS

ENE2017-82451-C3-1-R

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2017
State Plan 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre UNIVERSIDAD DE ZARAGOZA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Hydrodeoxygenation of vanillin over noble metal catalyst supported on biochars: Part II: Catalytic behaviour

  • Santos Muñoz, José Luis
  • Mäki-Arvela, Päivi
  • Wärnå, Johan
  • Monzón, Antonio
  • Centeno, Miguel Ángel
  • Murzin, Dmtry Yu.
Vanillin hydrodeoxygenation was investigated using noble metal (Pd, Au, Ru) supported on active carbon prepared from waste derived biochars, which were produced via pyrolysis in CO2 atmosphere. Chemical activation with ZnCl2 and HNO3 was also used in the preparation of active carbon to enhance the specific surface area and demineralize material, respectively. Both fresh and spent catalysts were characterized with X-ray diffraction, DRIFTS, zeta potential measurement and HR-TEM. The highest selectivity to p-creosol, 92 % selectivity at complete vanillin conversion after 3 h was obtained in vanillin hydrodeoxygenation at 100 °C under 30 bar in hydrogen in water with Pd/C catalyst prepared via pyrolysis under CO2 from wine waste and using ZnCl2 as a chemical activation agent. Hydrodeoxygenation activity increased with increasing metal dispersion. A kinetic model including adsorption of vanillin described well the experimental data., Financial support for this work has been obtained from the Spanish Ministerio de Economía y Competitividad (MINECO) (Grants ENE2013-47880-C3-2-R, ENE2017-82451-C3-3-R and ENE2017-82451-C3-1-R) co-financed by FEDER funds from the European Union. J.L. Santos also acknowledges the MINECO for his pre-doctoral fellowship (BES-2014-068244) and the mobility fellowship (EEBB-I-17-11979)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Metal catalysts supported on biochars: Part I synthesis and characterization

  • Santos, José Luis
  • Mäki-Arvela, Päivi
  • Monzón, Antonio
  • Murzin, Dmtry Yu.
  • Centeno, Miguel Ángel
In the current study, synthesis and detailed characterization of cellulose biochars as a waste biomass model component and vine shoot biochars as a real waste biomass catalyst was performed. Although initially biochars exhibit poor textural properties, a simple activation process can make them much more suitable as a catalyst supports. A combination of physical (CO2) and chemical activation (ZnCl2) was evaluated. The characterization results indicated that the surface area and pore volume of the biochars have increased significantly by chemical activation treatment with ZnCl2. A series of metal catalysts (Pd, Au and Ru) supported on biochars was prepared and characterized. The prepared materials represent a set of noble metal catalysts supported on biochars with different textural and surface properties, which can be used to evaluate the catalytic role of the active phase and carbon support nature in catalytic reactions of interest, such as hydrodeoxygenation, described in the part II., Financial support for this work has been obtained from the Spanish Ministerio de Economía y Competitividad (MINECO) (Grants ENE2013-47880-C3-2-R, ENE2017-82451-C3-3-R and ENE2017-82451-C3-1-R) co-financed by FEDER funds from the European Union. J.L. Santos also acknowledges the MINECO for his predoctoral fellowship (BES-2014-068244) and the mobility fellowship (EEBB-I-17-11979)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Fructose dehydration reaction over functionalized nanographitic catalysts in MIBK/H2O biphasic system

  • Delgado-Martín, Gabriel
  • Bounoukta, Charf Eddine
  • Ammari, Fatima
  • Domínguez, M. I.
  • Monzón, Antonio
  • Ivanova, Svetlana
  • Centeno, Miguel Ángel
A series of functionalized nanographitic carbons is prepared, characterized and tested in fructose dehydration reaction to 5-hydroxymethylfurfural. The functionalization treatment was selected to introduce various Brönsted acid sites and to modify the textural and catalytic properties of the initial carbon material. Within the series, the sulfonated carbons present the most interesting catalytic behavior resulting in important selectivity to the desired product once the reaction variables were properly adjusted., Financial support for this work has been obtained from the Spanish Ministerio de Economía y Competitividad (MINECO) (Projects ENE2017-82451-C3-1-R and ENE2017-82451-C3-3-R) co-financed by FEDER funds from the European Union.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Highly active Ce- and Mg-promoted Ni catalysts supported on cellulose-derived carbon for low-temperature CO2 methanation

  • Tarifa, Pilar
  • Megías-Sayago, Cristina
  • Cazaña, Fernando
  • González-Martín, Miguel
  • Latorre, Nieves
  • Romeo, Eva
  • Delgado, Juan José
  • Monzón, Antonio
The CO2 methanation performance of Mg- and/or Ce-promoted Ni catalysts supported on cellulose-derived carbon (CDC) was investigated. The samples, prepared by biomorphic mineralization techniques, exhibit pore distributions correlated to the particle sizes, revealing a direct effect of the metal content in the textural properties of the samples. The catalytic performance, evaluated as CO2 conversion and CH4 selectivity, reveals that Ce is a better promoter than Mg, reaching higher conversion values in all of the studied temperature range (150–500 °C). In the interval of 350–400 °C, Ni–Mg–Ce/CDC attains the maximum yield to methane, 80%, reaching near 100% CH4 selectivity. Ce-promoted catalysts were highly active at low temperatures (175 °C), achieving 54% CO2 conversion with near 100% CH4 selectivity. Furthermore, the large potential stability of the Ni–Mg–Ce/CDC catalyst during consecutive cycles of reaction opens a promising route for the optimization of the Sabatier process using this type of catalyst., The authors acknowledge financial support from the Spanish Ministry of Science and Innovation (MICINN, Madrid, Spain, Grant ENE2013-44350R) and MICINN–FEDER (Project ENE2017-82451-C3). Pilar Tarifa acknowledges financial support from the MICINN (Contract BES-2014-069010). Cristina Megías-Sayago acknowledges financial support from the MICINN “Juan de la Cierva Formación” Fellowship (FJC2018-037162-I)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Selective synthesis of carbon nanotubes by catalytic decomposition of methane using Co-Cu/cellulose derived carbon catalysts: A comprehensive kinetic study

  • Henao, Wilson
  • Cazaña, Fernando
  • Tarifa, Pilar
  • Romeo, Eva
  • Latorre, Nieves
  • Sebastián, Víctor
  • Delgado, Juan José
  • Monzón, Antonio
Determination of the optimal operating conditions for large-scale production of carbonaceous nanomaterials (CNTs), mainly carbon nanotubes (CNTs) but also graphene-related materials (GRMs), remains as a major industrial and scientific challenge. For this purpose, our group is conducting an extensive study to evaluate the effect of the reaction conditions and catalyst compositions on the productivity and selectivity to different carbonaceous nanomaterials. In the case of Co-based catalysts, we have found that the promotion with Cu or Mn has a dramatic effect on the type of carbon nanomaterials synthesized. Thus, the presence of Cu promotes the growth of CNTs, while Mn favors the formation of two-dimensional GRMs. In this context, we present here a comprehensive study of the CNTs growth via catalytic decomposition of methane using a Co-Cu/cellulose derived carbon catalyst. The influence of the reaction temperature (650–950 °C) and feed composition (7.1%–42.9% of CH4 and H2) on the yield and CNTs quality was evaluated. A transition in the characteristics of the carbonaceous nanomaterial growth was observed at about 800 °C. Below this temperature, the reaction was selective towards the formation of CNTs, while above 800 °C, the obtained nanomaterial exhibited a graphite-like morphology. In addition, the catalyst deactivation was quite low in the CNTs growth regime, attaining high productivity under 11 h of operation. The model used to study the kinetics of carbon formation allowed understanding the most influential variables in the growth process, revealing the existence of a transition temperature at which there is a change in the preferential path for the formation of CNTs or GRMs. After exploring a large set of reaction conditions, the best operating parameters for growing CNTs with high productivity (0.29 gC/gcat∙h) and quality (ID/IG = 1.10, I2D/IG = 0.13) were found at 750 °C under 28.6% CH4:14.3% H2:57.1% N2., The authors acknowledge financial support from the Ministry of Science and Innovation (Madrid, Spain), Projects ENE2017-82451-C3-1-R and ENE2017-82451-C3-2-R. W. Henao acknowledges the financial support from Fundación Carolina (Madrid, Spain) and the University of Zaragoza., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Performance of AISI 316L-stainless steel foams towards the formation of graphene related nanomaterials by catalytic decomposition of methane at high temperature

  • Cazaña, Fernando
  • Latorre, Nieves
  • Tarifa, Pilar
  • Royo, Carlos J.
  • Sebastián, Víctor
  • Romeo, Eva
  • Centeno, Miguel Ángel
  • Monzón, Antonio
This work explores the preparation of graphene-related materials (GRMs) grown on stainless steel foams via catalytic decomposition of methane (CDM). The main active phases for the reaction are the Fe nanoparticles segregated from the stainless-steel after the activation stage of the foam. The effect of the feed composition and reaction temperature has been studied in order to maximize the productivity, stability and selectivity to GRMs. The maximum productivity attained was 0.116 gC/gfoam h operating at 950 °C with a feed ratio of CH4/H2 = 3 (42.9 %CH4:14.3 %H2). The carbonaceous nanomaterials (CNMs) obtained were characterized by X-Ray diffraction, Raman spectroscopy and by transmission and scanning electron microscopy. The parameters of the kinetic model developed are directly related to the relevant stages of the process, including carburization, diffusion-precipitation and deactivation-regeneration. The balance among these sequential stages determines the overall performance of the activated foam. In conditions of rapid carburization of the Fe NPs (pCH4 > 14 %), the productivity to CNMs is favoured, avoiding an initial deactivation of the active sites by fouling with amorphous carbon. After a rapid carburization, the selectivity to the different CNMs is governed by the ratio CH4/H2, and mainly by the temperature. Thus, the formation of GRMs, mainly Few Layer Graphene (FLG) and even graphene, is favoured at temperatures above 900 °C. At lower temperatures, carbon nanotubes are formed., The authors acknowledge financial support from MICINN (Madrid, Spain) FEDER, Project ENE2017-82451-C3. P. Tarifa acknowledges the grant of MICINN (Ref.: BES-2014-069010)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Tesis doctoral (DoctoralThesis)

Experimental and kinetic study of bimetallic Pd-based catalysts for selective reduction of nitrates in aqueous phase

  • González-Martín, Miguel
Programa de Doctorado en Ingeniería Química y del Medio Ambiente., [EN] Population growth and the need to supply a high demand for food has led to inefficient production and use of fertilisers leading to nitrate pollution in water, with the danger, among others, of causing cancer or blue baby syndrome in humans. Despite extensive legislation on nitrate, nitrite and ammonium pollution, nitrate, nitrite and ammonium contamination is widespread worldwide. However, an optimal industrial-scale method to solve this problem with the lowest possible drawback has not yet been found. Among the existing methods, selective catalytic nitrate reduction shows great potential to decompose nitrates into nitrogen gas, an inert and harmless gas, in a short period of time, in a reduced space and without producing other products that require further treatment, as brines or sludge. The main goal of this Doctoral Thesis has been to extend the knowledge on the influence of the operating variables of reaction, and of the composition and properties of the catalysts on their activity, stability and selectivity. To fulfil this purpose, different PdCu and PdSn catalysts supported on γ-alumina, and PdCu catalysts supported on a commercial graphite (Asbury-4124®) modified with thermal and chemical treatments have been synthesized. After the synthesis of these catalysts, physico-chemical characterization of the catalysts was carried out to know the influence of synthesis variables studied on the catalyst properties and subsequently on its catalytic performance. The techniques used were: X-ray diffraction (XRD), Scanning electron microscopy (SEM), Transmission electron microscopy (TEM), Nitrogen adsorption analysis, Temperature programmed reduction (TPR), Atomic absorption spectroscopy (AAS), Temperature programmed desorption coupled to a mass spectrometer (TPD-MS), Raman spectroscopy (Raman) and X-ray photoelectron spectroscopy (XPS). A series of PdCu/Al2O3 catalysts were synthesized fixing the Cu content at 0.4% w.t. and varying the Pd content between 0.25, 0.5, 0.75 and 1% w.t. Using these catalysts, the influence of the amount of noble metal in the catalyst was studied. Furthermore, using the 1Pd0.4Cu/Al2O3 catalyst, the influence of the stirring speed was studied by varying it from 520 rpm to 1500 rpm. After that, the influence of the catalyst loading on the reaction was studied by introducing catalyst concentrations from 0.25g/L to 2g/L. The influence of the ratio of H2 and CO2 in the feed was also studied, in this case the ratio of H2 and CO2 in the feed was varied while the total flow remained constant at 900 Nml/min. To study the influence of the ions in the dissolution, a catalytic study was carried out using 3 different types of water: distilled water, mineral water and tap water. Finally, using the 1Pd0.4Cu/Al2O3 catalyst, a study of the combination of the catalytic selective reduction of nitrates in conjunction with Amberlite® H + cation exchange resins was carried out, varying the load of cation exchange resin introduced from 0g to 6g of resin. Using the same Al2O3 support, a series of catalysts was synthesized using Sn as promoter metal. In this case, first two catalysts were prepared with 1%Pd w.t. and 0.4%Sn w.t. varying the order of impregnation of the metals. After this first test, it was decided to continue the synthesis with a first Sn impregnation followed by Pd impregnation. After that, the studies continued with the amount of promoter metal in the catalyst varying the amount of Sn between 0.2 and 2.5% w.t. and fixing 1% of Pd. Subsequently, the amount of Sn was fixed at 1.2% w.t. and the influence of the amount of Pd was studied, varying this percentage between 0.6 and 4% w.t. The results obtained were similar to those obtained in the case of the PdCu/Al2O3 study. After these tests, it was decided to use the 1Pd1.2Sn/Al2O3 catalyst to study the influence of the ratio of H2 and CO2 in the feed by varying the ratio between these two gases in the feed, however in this case the H2 flow rate was kept constant at 100NmL/min and the CO2 flow rate was varied from 0 to 400 NmL/min. In the same way as for PdCu/Al2O3, the influence of ions in water was studied using distilled water and tap water in the reaction. Finally, the influence of the reduction temperature of the catalyst prior to the reaction was studied by varying the reduction temperature from 250ºC to 550ºC. The last studies were carried out using the catalysts synthesized with commercial graphite (Asbury® 4124). In this case six catalysts were synthesized: three were synthesized in reducing atmosphere using a flow rate of 300NmL/min and a H2/N2 ratio of 1, while the other 3 were synthesized in an oxidizing atmosphere using an air flask. In addition, four of these catalysts were modified by chemical treatments, two of the catalysts (one in a reducing atmosphere and one in an oxidizing atmosphere) were coimpregnated with urea during the synthesis, while the other two (one in a reducing atmosphere and one in an oxidizing atmosphere) were subjected to oxidation with HNO3 prior to impregnation with the metals. All these catalysts were then tested in the selective catalytic reduction of nitrates. Using all these results, a kinetic model has been developed and adjusted to take into account the evolution of the main reactants and products, nitrates, nitrites, ammonium and nitrogen gas. In addition, this model takes into account the possible deactivation of the catalyst, the evolution of the intermediate compound NO or the reconversion of NO to NO2-. This model has even been modified to take into account the presence of cation exchange resins, all of which has allowed us to quantify the influence of the different variables and deepen our knowledge of the reaction. This model allows the simultaneous calculation of the evolution of all relevant species: NO3-, NO2-, NO, N2 and NH4+. The calculation of the kinetic parameters has been made by a multi-response non-linear regression procedure, solving numerically the set of differential-algebraic equations proposed., [ES] El crecimiento de la población y la necesidad de abastecer una gran demanda de alimentos ha llevado a una producción y uso ineficientes de fertilizantes que provocan la contaminación del agua por nitratos, con el peligro, entre otros, de causar cáncer o el síndrome del bebé azul en humanos. A pesar de la amplia legislación sobre contaminación por nitratos, nitritos y amonio, la contaminación por nitratos, nitritos y amonio está muy extendida en todo el mundo. Sin embargo, aún no se ha encontrado un método óptimo a escala industrial para resolver este problema. Entre los métodos existentes, la reducción catalítica selectiva de nitratos muestra un gran potencial para descomponer los nitratos en nitrógeno gas, un gas inerte e inocuo, en un corto periodo de tiempo, en un espacio reducido y sin producir otros productos que requieran tratamiento posterior, como salmueras o lodos. El objetivo principal de esta Tesis Doctoral ha sido ampliar el conocimiento sobre la influencia de las variables operativas de reacción, y de la composición y propiedades de los catalizadores en su actividad, estabilidad y selectividad. Para ello se han sintetizado diferentes catalizadores de PdCu y PdSn soportados sobre γalúmina, y catalizadores de PdCu soportados sobre un grafito comercial (Asbury4124®) modificado con tratamientos térmicos y químicos. Tras la síntesis de estos catalizadores, se llevó a cabo la caracterización físico-química de los mismos para conocer la influencia de las variables de síntesis estudiadas sobre las propiedades del catalizador y posteriormente sobre su rendimiento catalítico. Las técnicas utilizadas fueron: Difracción de rayos X (XRD), Microscopía electrónica de barrido (SEM), Microscopía electrónica de transmisión (TEM), Análisis de adsorción de nitrógeno, Reducción programada por temperatura (TPR), Espectroscopía de absorción atómica (AAS), Desorción programada por temperatura acoplada a un espectrómetro de masas (TPD-MS), Espectroscopía Raman (Raman) y Espectroscopía de fotoelectrones de rayos X (XPS). Se sintetizaron una serie de catalizadores PdCu/Al2O3 fijando el contenido de Cu al 0.4% en peso y variando el contenido de Pd entre 0.25, 0.5, 0.75 y 1% en peso. Utilizando estos catalizadores, se estudió la influencia de la cantidad de metal noble en el catalizador. Además, utilizando el catalizador 1Pd0.4Cu/Al2O3, se estudió la influencia de la velocidad de agitación variándola de 520 rpm a 1500 rpm. A continuación, se estudió la influencia de la carga de catalizador en la reacción introduciendo concentraciones de catalizador de 0.25g/L a 2g/L. También se estudió la influencia de la proporción de H2 y CO2 en la alimentación, en este caso se varió la proporción de H2 y CO2 en la alimentación mientras que el caudal total se mantuvo constante a 900 Nml/min. Para estudiar la influencia de los iones en la disolución, se realizó un estudio catalítico utilizando 3 tipos diferentes de agua: agua destilada, agua mineral y agua del grifo. Por último, utilizando el catalizador 1Pd0.4Cu/Al2O3, se realizó un estudio de la combinación de la reducción selectiva catalítica de nitratos junto con resinas de intercambio catiónico Amberlite® H+, variando la carga de resina de intercambio catiónico introducida desde 0g hasta 6g de resina. Utilizando el mismo soporte de Al2O3, se sintetizó una serie de catalizadores empleando Sn como metal promotor. En este caso, los dos primeros catalizadores se prepararon con 1%Pd en peso y 0.4%Sn en peso variando el orden de impregnación de los metales. Tras esta primera prueba, se decidió continuar la síntesis con una primera impregnación de Sn seguida de la impregnación de Pd. Después, los estudios continuaron con la cantidad de metal promotor en el catalizador variando la cantidad de Sn entre 0.2 y 2.5% en peso y fijando un 1% de Pd. Posteriormente, se fijó la cantidad de Sn en 1.2% en peso y se estudió la influencia de la cantidad de Pd, variando este porcentaje entre 0.6 y 4%. Los resultados obtenidos fueron similares a los obtenidos en el caso del estudio de PdCu/Al2O3. Tras estas pruebas, se decidió utilizar el catalizador 1Pd1.2Sn/Al2O3 para estudiar la influencia de la relación de H2 y CO2 en la alimentación variando la relación entre estos dos gases en la alimentación, sin embargo, en este caso el caudal de H2 se mantuvo constante en 100NmL/min y el caudal de CO2 se varió de 0 a 400 NmL/min. De la misma manera que para PdCu/Al2O3, se estudió la influencia de los iones en el agua utilizando agua destilada y agua del grifo en la reacción. Por último, se estudió la influencia de la temperatura de reducción del catalizador antes de la reacción variando la temperatura de reducción de 250ºC a 550ºC. Los últimos estudios se realizaron utilizando los catalizadores sintetizados con grafito comercial (Asbury® 4124). En este caso se sintetizaron seis catalizadores: tres se sintetizaron en atmósfera reductora utilizando un caudal de 300NmL/min y una relación H2/N2 de 1, mientras que los otros 3 se sintetizaron en atmósfera oxidante utilizando un matraz de aire. Además, cuatro de estos catalizadores se modificaron mediante tratamientos químicos, dos de los catalizadores (uno en atmósfera reductora y otro en atmósfera oxidante) se coimpregnaron con urea durante la síntesis, mientras que los otros dos (uno en atmósfera reductora y otro en atmósfera oxidante) se sometieron a oxidación con HNO3 antes de la impregnación con los metales. A continuación, todos estos catalizadores se ensayaron en la reducción catalítica selectiva de nitratos. A partir de todos estos resultados, se ha desarrollado y ajustado un modelo cinético que tiene en cuenta la evolución de los principales reactivos y productos, nitratos, nitritos, amonio y nitrógeno gas. Además, este modelo tiene en cuenta la posible desactivación del catalizador, la evolución del compuesto intermedio NO o la reconversión de NO en NO2-. Este modelo ha sido incluso modificado para tener en cuenta la presencia de resinas de intercambio catiónico, todo lo cual ha permitido cuantificar la influencia de las distintas variables y profundizar en el conocimiento de la reacción. Este modelo permite calcular simultáneamente la evolución de todas las especies relevantes: NO3-, NO2-, NO, N2 y NH4+. El cálculo de los parámetros cinéticos se ha realizado mediante un procedimiento de regresión no lineal multirrespuesta, resolviendo numéricamente el conjunto de ecuaciones diferenciales-algebraicas propuestas., Me gustaría agradecer al Ministerio de Ciencia, Innovación y Universidades por la concesión de mi beca FPI (PRE2018-086557) gracias al cual he podido realizar este trabajo de investigación. Y a los proyectos “Aprovechamiento de biomasa y producción sostenible de energía mediante (foto)catalizadores y reactores estructurados basados en materiales carbonosos” (ENE2017-82451-C3-1-R) y “Catalizadores Basados en Carbón Derivado de Biomasa para la Producción y Uso de Hidrógeno Verde” (PID2020-113809RB-C31)., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Selective synthesis of carbon nanotubes by catalytic decomposition of methane using Co-Cu/cellulose derived carbon catalysts: A comprehensive kinetic study

  • Henao, W.
  • Cazaña, F.
  • Tarifa, P.
  • Romeo, E.
  • Latorre, N.
  • Sebastian, V.
  • Delgado, J.J.
  • Monzón, A.
Determination of the optimal operating conditions for large-scale production of carbonaceous nanomaterials (CNTs), mainly carbon nanotubes (CNTs) but also graphene-related materials (GRMs), remains as a major industrial and scientific challenge. For this purpose, our group is conducting an extensive study to evaluate the effect of the reaction conditions and catalyst compositions on the productivity and selectivity to different carbonaceous nanomaterials. In the case of Co-based catalysts, we have found that the promotion with Cu or Mn has a dramatic effect on the type of carbon nanomaterials synthesized. Thus, the presence of Cu promotes the growth of CNTs, while Mn favors the formation of two-dimensional GRMs. In this context, we present here a comprehensive study of the CNTs growth via catalytic decomposition of methane using a Co-Cu/cellulose derived carbon catalyst. The influence of the reaction temperature (650–950 °C) and feed composition (7.1%–42.9% of CH4 and H2) on the yield and CNTs quality was evaluated. A transition in the characteristics of the carbonaceous nanomaterial growth was observed at about 800 °C. Below this temperature, the reaction was selective towards the formation of CNTs, while above 800 °C, the obtained nanomaterial exhibited a graphite-like morphology. In addition, the catalyst deactivation was quite low in the CNTs growth regime, attaining high productivity under 11 h of operation. The model used to study the kinetics of carbon formation allowed understanding the most influential variables in the growth process, revealing the existence of a transition temperature at which there is a change in the preferential path for the formation of CNTs or GRMs. After exploring a large set of reaction conditions, the best operating parameters for growing CNTs with high productivity (0.29 gC/gcat·h) and quality (ID/IG = 1.10, I2D/IG = 0.13) were found at 750 °C under 28.6% CH4:14.3% H2:57.1% N2.