Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Performance of AISI 316L-stainless steel foams towards the formation of graphene related nanomaterials by catalytic decomposition of methane at high temperature

  • Cazaña, Fernando
  • Latorre, Nieves
  • Tarifa, Pilar
  • Royo, Carlos J.
  • Sebastián, Víctor
  • Romeo, Eva
  • Centeno, Miguel Ángel
  • Monzón, Antonio
This work explores the preparation of graphene-related materials (GRMs) grown on stainless steel foams via catalytic decomposition of methane (CDM). The main active phases for the reaction are the Fe nanoparticles segregated from the stainless-steel after the activation stage of the foam. The effect of the feed composition and reaction temperature has been studied in order to maximize the productivity, stability and selectivity to GRMs. The maximum productivity attained was 0.116 gC/gfoam h operating at 950 °C with a feed ratio of CH4/H2 = 3 (42.9 %CH4:14.3 %H2). The carbonaceous nanomaterials (CNMs) obtained were characterized by X-Ray diffraction, Raman spectroscopy and by transmission and scanning electron microscopy. The parameters of the kinetic model developed are directly related to the relevant stages of the process, including carburization, diffusion-precipitation and deactivation-regeneration. The balance among these sequential stages determines the overall performance of the activated foam. In conditions of rapid carburization of the Fe NPs (pCH4 > 14 %), the productivity to CNMs is favoured, avoiding an initial deactivation of the active sites by fouling with amorphous carbon. After a rapid carburization, the selectivity to the different CNMs is governed by the ratio CH4/H2, and mainly by the temperature. Thus, the formation of GRMs, mainly Few Layer Graphene (FLG) and even graphene, is favoured at temperatures above 900 °C. At lower temperatures, carbon nanotubes are formed., The authors acknowledge financial support from MICINN (Madrid, Spain) FEDER, Project ENE2017-82451-C3. P. Tarifa acknowledges the grant of MICINN (Ref.: BES-2014-069010)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Steam reforming of clean biogas over Rh and Ru open-cell metallic foam structured catalysts

  • Tarifa, Pilar
  • Schiaroli, Nicola
  • Ho, Phuoc Hoang
  • Cañaza, Fernando
  • Ospitali, Francesca
  • Sanghez de Luna, Giancosimo
  • Lucarelli, Carlo
  • Fornasari, Giuseppe
  • Vaccari, Angelo
  • Monzón, Antonio
  • Benito, Patricia
The valorisation of clean biogas (CH4/CO2 = 60/40 v/v) by steam reforming over metal open-cell foam-based structured catalysts was investigated. NiCrAl foams were coated by RuMgAl or RhMgAl hydrotalcite-type compounds through electrodeposition to obtain, after calcination, a thin and stable catalytic film of oxides. The active sites for the reforming reactions are highly dispersed Rh or Ru nanoparticles stabilized by a strong metal support interaction, large Ni particles segregated from the support during reduction and reaction, and Rh/Ni bimetallic particles formed by the interaction of the two formers. Rh-based catalysts show superior activity and stability with the time on stream than Ru catalysts, and a low carbon deposition, which is mainly ascribable to the presence of large Ni particles. In comparison to a pelletized catalyst, the structured catalysts are allowed to operate at high space velocities and low Steam to CH4 ratio, increasing the biogas valorisation and thus the productivity., P. Tarifa acknowledges the financial support of Spanish Ministry of Science and Innovation (Ref.: BES-2014-069010)., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Performance of AISI 316L-stainless steel foams towards the formation of graphene related nanomaterials by catalytic decomposition of methane at high temperature

  • Cazaña, F.
  • Latorre, N.
  • Tarifa, P.
  • Royo, C.J.
  • Sebastián, V.
  • Romeo, E.
  • Centeno, M.A.
  • Monzón, A.
This work explores the preparation of graphene-related materials (GRMs) grown on stainless steel foams via catalytic decomposition of methane (CDM). The main active phases for the reaction are the Fe nanoparticles segregated from the stainless-steel after the activation stage of the foam. The effect of the feed composition and reaction temperature has been studied in order to maximize the productivity, stability and selectivity to GRMs. The maximum productivity attained was 0.116 gC/gfoam h operating at 950 °C with a feed ratio of CH4/H2 = 3 (42.9 %CH4:14.3 %H2). The carbonaceous nanomaterials (CNMs) obtained were characterized by X-Ray diffraction, Raman spectroscopy and by transmission and scanning electron microscopy. The parameters of the kinetic model developed are directly related to the relevant stages of the process, including carburization, diffusion-precipitation and deactivation-regeneration. The balance among these sequential stages determines the overall performance of the activated foam. In conditions of rapid carburization of the Fe NPs (pCH4 > 14 %), the productivity to CNMs is favoured, avoiding an initial deactivation of the active sites by fouling with amorphous carbon. After a rapid carburization, the selectivity to the different CNMs is governed by the ratio CH4/H2, and mainly by the temperature. Thus, the formation of GRMs, mainly Few Layer Graphene (FLG) and even graphene, is favoured at temperatures above 900 °C. At lower temperatures, carbon nanotubes are formed.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Highly active Ce- And Mg-promoted Ni catalysts supported on cellulose-derived carbon for low-temperature CO2 methanation

  • Tarifa, Pilar
  • Megías-Sayago, Cristina
  • Cazaña, Fernando
  • González-Martín, Miguel
  • Latorre, Nieves
  • Romeo, Eva
  • Delgado, Juan José
  • Monzón, Antonio
The CO2 methanation performance of Mg- and/or Ce-promoted Ni catalysts supported on cellulose-derived carbon (CDC) was investigated. The samples, prepared by biomorphic mineralization techniques, exhibit pore distributions correlated to the particle sizes, revealing a direct effect of the metal content in the textural properties of the samples. The catalytic performance, evaluated as CO2 conversion and CH4 selectivity, reveals that Ce is a better promoter than Mg, reaching higher conversion values in all of the studied temperature range (150-500 °C). In the interval of 350-400 °C, Ni-Mg-Ce/CDC attains the maximum yield to methane, 80%, reaching near 100% CH4 selectivity. Ce-promoted catalysts were highly active at low temperatures (175 °C), achieving 54% CO2 conversion with near 100% CH4 selectivity. Furthermore, the large potential stability of the Ni-Mg-Ce/CDC catalyst during consecutive cycles of reaction opens a promising route for the optimization of the Sabatier process using this type of catalyst.