Skip to main content

REFOMADO SECO DE BIOGAS: INTENSIFICACION DEL PROCESO CON FINES ENERGETICOS

ENE2013-44350-R

•
Funding agency name Ministerio de Economía y Competitividad
Funding agency acronym MINECO
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2013
State Plan 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Management unit Secretaría de Estado de Educación, Formación Profesional y Universidades
Beneficiary centre UNIVERSIDAD DE ZARAGOZA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 14
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Highly active Ce- and Mg-promoted Ni catalysts supported on cellulose-derived carbon for low-temperature CO2 methanation

  • Tarifa, Pilar
  • Megías-Sayago, Cristina
  • Cazaña, Fernando
  • González-Martín, Miguel
  • Latorre, Nieves
  • Romeo, Eva
  • Delgado, Juan José
  • Monzón, Antonio
The CO2 methanation performance of Mg- and/or Ce-promoted Ni catalysts supported on cellulose-derived carbon (CDC) was investigated. The samples, prepared by biomorphic mineralization techniques, exhibit pore distributions correlated to the particle sizes, revealing a direct effect of the metal content in the textural properties of the samples. The catalytic performance, evaluated as CO2 conversion and CH4 selectivity, reveals that Ce is a better promoter than Mg, reaching higher conversion values in all of the studied temperature range (150–500 °C). In the interval of 350–400 °C, Ni–Mg–Ce/CDC attains the maximum yield to methane, 80%, reaching near 100% CH4 selectivity. Ce-promoted catalysts were highly active at low temperatures (175 °C), achieving 54% CO2 conversion with near 100% CH4 selectivity. Furthermore, the large potential stability of the Ni–Mg–Ce/CDC catalyst during consecutive cycles of reaction opens a promising route for the optimization of the Sabatier process using this type of catalyst., The authors acknowledge financial support from the Spanish Ministry of Science and Innovation (MICINN, Madrid, Spain, Grant ENE2013-44350R) and MICINN–FEDER (Project ENE2017-82451-C3). Pilar Tarifa acknowledges financial support from the MICINN (Contract BES-2014-069010). Cristina Megías-Sayago acknowledges financial support from the MICINN “Juan de la Cierva Formación” Fellowship (FJC2018-037162-I)., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Gas permeation effect on the Two-Section Two-Zone Fluidized Bed Membrane Reactor (TS-TZFBMR) fluid dynamics: A CFD simulation study

  • Julián, I.
  • Herguido, J.
  • Menéndez, M.
Two-Fluid Model simulations were conducted using the commercial software Ansys CFX and Fluent to study the effect of the gas extraction on the fluid dynamic behavior of a membrane-assisted Two-Section Two-Zone Fluidized Bed Membrane Reactor (TS-TZFBMR). Simulated bubble properties and bed dynamics were analyzed and compared among different membrane reactor configurations, including reactor-wall (RWM) and immersed tubular (ITM) membranes, for their future use in catalytic reactions, e.g., alkane dehydrogenation or methane steam reforming. According to the solids hold-up distribution at different fluidization regimes and permeation fluxes, the ITM configuration is the most suitable to enhance the gas-particle contact and to favor the solids axial mixing for in-situ catalyst regeneration purposes. However, the RWM configuration provides a greater permeation area for selective gas removal and is preferred to enhance purification. It was found that relative permeation fluxes above 20% of the total feed gas have a significant impact on the fluid dynamic regime within the TS-TZFBMR, concerning the appearance of local defluidized regions, gas channeling and solids axial mixing.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Use of a-shapes for the measurement of 3D bubbles in fluidized beds from two-fluid model simulations

  • Julián, I.
  • González, D.
  • Herguido, J.
  • Menéndez, M.
A geometrical technique based on shape construction was employed to reconstruct the simulated domain of 3D bubbles in a gas-solid fluidized bed, from two-fluid model (TFM) simulations. The Delaunay triangulation of the cloud of points that represent volume fraction iso-surfaces in transient TFM simulations was filtered by means of the so-called a-shapes, allowing a topologically accurate description of 3D bubbles within a fluidized bed. Consequently, individual 3D bubble properties such as size and velocity were measured. Simulated bubble characteristics were further compared to those measured on pseudo-2D bed facilities by image techniques in order to illustrate the effect of the bed geometry on the bubbling behavior under mimicked operational conditions.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Reseña (Review)

Advances and trends in two-zone fluidized-bed reactors

  • Herguido, J.
  • Menéndez, M.
Two-zone fluidized bed reactors, devices to carry on two reactions in a single reactor, have been widely studied in our group. This work summarizes the developments achieved after a previous review published in 2005 and shows how this technology can be applied in a wide variety of reactions. The advantages for each kind of process are discussed, as well as several proposals for improvement of the reactor aimed to achieve new functions or to improve the process performance. Finally, the possibilities of this kind of reactors at industrial scale are discussed.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Iron oxide ores as carriers for the production of high purity hydrogen from biogas by steam–iron process

  • Lachén, J.
  • Plou, J.
  • Durán, P.
  • Herguido, J.
  • Peña, J.A.
Production of high purity hydrogen (<50 ppm CO) by steam–iron process (SIP) from a synthetic sweetened biogas has been investigated making use of a natural iron ore containing up to 81 wt% of hematite (Fe2O3) as oxygen carrier. The presence of a lab-made catalyst (NiAl2O4 with NiO excess above its stoichiometric composition) was required to carry out the significant transformation of mixtures of methane and carbon dioxide in hydrogen and carbon monoxide by methane dry reforming reaction. Three consecutive sub-stages have been identified along the reduction stage that comprise A) the combustion of CH4 by lattice oxygen of NiO and Fe2O3, B) catalyzed methane dry reforming and C) G–G equilibrium described by the Water-Gas-Shift reaction. Oxidation stages were carried out with steam completing the cycle. Oxidation temperature was always kept constant at 500 °C regardless of the temperature used in the previous reduction to minimize the gasification of eventual carbon deposits formed along the previous reduction stage. The presence of other oxides different from hematite in minor proportions (SiO2, Al2O3, CaO and MgO to name the most significant) confers it an increased thermal resistance against sintering respecting pure hematite at the expense of slowing down the reduction and oxidation rates. A “tailor made” hematite with additives (Al2O3 and CeO2) in minor proportions (2 wt%) has been used to stablish comparisons in performance between natural and synthetic iron oxides. It has been investigated the effect of the reduction temperature, the proportion of methane to carbon dioxide in the feed (CH4:CO2 ratio) and the number of repetitive redox cycles.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Dry reforming of biogas in fluidized bed: Process intensification

  • Ugarte, P.
  • Durán, P.
  • Lasobras, J.
  • Soler, J.
  • Menéndez, M.
  • Herguido, J.
Biogas is a renewable resource obtained mainly from the anaerobic fermentation of agro-industrial and anthropogenic residues. The production of hydrogen by dry reforming of methane represents a potential application for this renewable energy carrier. This could play a positive contribution towards meeting the challenge of providing a global supply of energetically sustainable and environmentally friendly energy. This work combines a catalytic reaction, a separation and the catalyst regeneration in a single reactor. To this end, a two zone fluidized bed reactor (TZFBR) with hydrogen selective membranes has been employed (TZFBR + MB). The operating conditions for the process of dry reforming of biogas have been optimized experimentally, both in TZFBR and TZFBR + MB. Several catalysts were prepared (Ni/Al2O3, Ni–Ce/Al2O3, Ni–Co/Al2O3), characterized and tested in reactions in both TZFBR and in TZFBR + MB. Finally, the influence of using oxygen or carbon dioxide as regenerating gases in the process has been studied. Experimental results show the feasibility of using CO2 for in situ catalyst regeneration, avoiding the potential problems associated with the use of O2.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Glycerol steam reforming with low steam/glycerol ratio in a two-zone fluidized bed reactor

  • Yus, M.
  • Soler, J.
  • Herguido, J.
  • Menéndez, M.
The production of hydrogen from glycerol steam reforming has been studied in several reactors. In conventional reactors the catalyst is deactivated by coke: in fixed bed reactors plugging was observed if a low steam/glycerol ratio was employed, while in fluidized bed reactors it was possible to operate for a longer time-on-stream. The use of a two-zone fluidized bed reactor is studied in this work, as a method to counteract the problem of catalyst deactivation by coke. The glycerol reforming takes place in the upper part of this reactor while the catalyst is simultaneously regenerated in the lower part, where a stream of a regenerating gas is introduced. It has been found that CO2, O2 or H2O can act as regenerating gas in a two-zone-fluidized bed reactor, allowing steady state operation at a water:glycerol molar ratio as low as 1.25. The effect of the operating conditions has been studied and the yield to the main products was compared with the calculated values assuming thermodynamic equilibrium.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Preliminary study on the feasibility of using a zeolite A membrane in a membrane reactor for methanol production

  • Gorbe, J.
  • Lasobras, J.
  • Francés, E.
  • Herguido, J.
  • Menéndez, M.
  • Kumakiri, I.
  • Kita, H.
The permeation of a mixture containing H2, CO2 and water through a zeolite membrane was studied under several operating conditions. The aim was to obtain insight on the feasibility of using such membrane in a zeolite membrane reactor for CO2 hydrogenation to methanol. The effects of total pressure (100–270 kPa), water partial pressure (10–18 kPa) and temperature (160–260 °C) were studied. Promising water-permanent gas separation factors were obtained up to 240 °C. A surprisingly high water partial pressure was found in the permeate in some cases, which is explained by the radial temperature gradient in the experimental system. The good capability of this zeolite A membrane to selectively separate water vapor makes it a promising material for its use in a zeolite membrane reactor.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Biogas to high purity hydrogen by methane dry reforming in TZFBR+MB and exhaustion by Steam-Iron Process. Techno–economic assessment

  • Lachén, J.
  • Durán, P.
  • Menéndez, M.
  • Peña, J.A.
  • Herguido, J.
A techno-economic study has been carried out with the aim of analyzing the performance (product distribution and energy yields) and estimating the production costs of high purity hydrogen obtained from biogas. For such purpose and taking advantage of empirical data developed in our laboratory, it has been proposed a system consisting of a two-zone fluidized bed reactor aided by a system of permselective (Pd/Ag) metallic membranes inserted in the fluidized bed (TZFBR+MB), and a battery of several fixed bed reactors operating cycles of reduction and oxidation (Steam-Iron Process -SIP-). The feed has always been an equimolar mixture of CH4 and CO2 simulating a sweetened biogas. The first reactor (TZFBR+MB) can produce a stream of pure hydrogen (i.e. PEMFC quality) as permeated flow through the MB, and a retentate stream rich in all species resulting from the methane dry reforming reaction (MDR) and the water gas shift equilibrium (WGS). The singularity of this kind of complex reactors is that regeneration of the catalyst is performed in the same reactor and simultaneously to the MDR reaction because of the two-zone. Due to the reductive behavior of the retentate stream, it can be fed to a bed of solid where up to two different oxygen carriers (iron oxide with additives and cobalt ferrite) can be reduced to their metallic state. Once the solid has been completely reduced, it can be reoxidized with steam releasing a high purity hydrogen stream. Both reactors (i.e. TZFBR+MB and SIP) have been coupled in different degrees. A performance (hydrogen and energy yields) as well as costs analysis (fixed assets and operating costs) have been performed with the aid of Aspen HYSYS v9.0, used for dimensioning the equipment needed to process up to 1350 kg/h of biogas. On this way, the integrated process enhances the efficiencies of every single process allowing pure hydrogen yields up to 68% at 575 °C in the TZFBR+MB and an overall energy efficiency greater than 45%. Production costs have been found to be in the range from 4 to 15 €/kg, still high but not so far away from the target of DOE fixed in 2 $/kg by 2020.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Production and purification of hydrogen by biogas combined reforming and steam-iron process

  • Lachén, J.
  • Herguido, J.
  • Peña, J.A.
Cobalt ferrite and hematite with minor additives have been tested for production and purification of high purity hydrogen from a synthetic biogas by steam-iron process (SIP) in a fixed bed reactor. A catalyst based in nickel aluminate has been included in the bed of solids to enhance the rate of the reaction of methane dry reforming (MDR). The reductants resulting from MDR are responsible for reducing the oxides based on iron that will, in the following stage, be oxidized by steam to release hydrogen with less than 50 ppm of CO. Coke minimization along reduction stages forces to operate such reactors above 700 °C for reductions, and as low as 500 °C for oxidations to avoid coke gasification. To avoid problems such as reactor clogging by coke in reductions and/or contamination of hydrogen by gasification of coke along oxidations, steam in small proportions has been included in the feed with the aim of minimizing or even avoiding formation of carbonaceous depositions along the reduction stage of SIP. Since steam is an oxidant, it exerts an inhibiting effect upon reduction of the oxide, that slows down the efficiency of the process. It has been proved that co-feeding low proportions of steam with an equimolar mixture of CH4 and CO2 (simulating a poor heating value desulphurized biogas) is able to avoid coke deposition, allowing the operation of both, reductions and oxidations, in isothermal regime (700 °C). Empirical results have been contrasted with data found in literature for similar processes based in MDR and combined (or mixed) reforming process (CMR), concluding that the combination of MDR + SIP proposed in this work, taking apart economic aspects and complex engineering, shows similar yields towards hydrogen, but with the advantage of not requiring a subsequent purification process.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Kinetic Study of Dry Reforming of Methane Over Ni–Ce/Al 2 O 3 Catalyst with Deactivation

  • Zambrano, D.
  • Soler, J.
  • Herguido, J.
  • Menéndez, M.
A kinetic study for dry reforming of methane over Ni–Ce/Al 2 O 3 catalyst was performed, taking into account both the main reactions and the catalyst deactivation. The catalyst was prepared by a sequential wet impregnation process, with loadings of 5 wt.% Ni and 10 wt.% Ce. Experimental tests were carried out in a fixed bed reactor between 475 and 550 °C and several spatial times, using nitrogen as diluent. Several kinetic equations were compared. The best fit of experimental data was achieved using a Langmuir–Hinshelwood mechanism which takes into account the presence of two active sites. Pre-exponential factor and activation energy were calculated. the kinetics of deactivation was also determined. The relationship between catalyst activity and coke concentration was also studied. Several deactivation equations were considered in order to choose the best fit with experimental data.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Pure hydrogen from biogas: Intensified methane dry reforming in a two-zone fluidized bed reactor using permselective membranes

  • Durán, P.
  • Sanz-Martínez, A.
  • Soler, J.
  • Menéndez, M.
  • Herguido, J.
Methane dry reforming of biogas can be a sustainable source of hydrogen but the development of this technology is hindered by limitations such as endothermicity and catalyst deactivation by coke. A two zone fluidized bed reactor coupling permselective Pd/Ag membranes counteracts them and allows to intensify the process obtaining a stable pure hydrogen production. Here we report the effect of operation variables (i.e., temperature, total bed height, nature and partial pressure of regenerative agent, relative height of the regeneration and reaction zones, and use of an activation period) on the yield to hydrogen and stability of the process. Hydrogen over-yields, compared with the conventional fluidized bed reactor, in the range of +200% to +100% were obtained for the entire interval of temperatures 475–575 °C whilst maintaining stable operation by continuous catalyst regeneration. Around 70% of it was pure hydrogen coming from the permeate side of the membranes. The proposed reactor configuration greatly increases both methane conversion and selectivity to hydrogen (expressed as H 2 /CO ratio), not only in relation to our own conventional reactor findings but also regarding other published results.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Highly active Ce- And Mg-promoted Ni catalysts supported on cellulose-derived carbon for low-temperature CO2 methanation

  • Tarifa, Pilar
  • Megías-Sayago, Cristina
  • Cazaña, Fernando
  • González-Martín, Miguel
  • Latorre, Nieves
  • Romeo, Eva
  • Delgado, Juan José
  • Monzón, Antonio
The CO2 methanation performance of Mg- and/or Ce-promoted Ni catalysts supported on cellulose-derived carbon (CDC) was investigated. The samples, prepared by biomorphic mineralization techniques, exhibit pore distributions correlated to the particle sizes, revealing a direct effect of the metal content in the textural properties of the samples. The catalytic performance, evaluated as CO2 conversion and CH4 selectivity, reveals that Ce is a better promoter than Mg, reaching higher conversion values in all of the studied temperature range (150-500 °C). In the interval of 350-400 °C, Ni-Mg-Ce/CDC attains the maximum yield to methane, 80%, reaching near 100% CH4 selectivity. Ce-promoted catalysts were highly active at low temperatures (175 °C), achieving 54% CO2 conversion with near 100% CH4 selectivity. Furthermore, the large potential stability of the Ni-Mg-Ce/CDC catalyst during consecutive cycles of reaction opens a promising route for the optimization of the Sabatier process using this type of catalyst.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

High purity hydrogen from biogas via steam iron process: Preventing reactor clogging by interspersed coke combustions

  • Lachén, J.
  • Herguido, J.
  • Peña, J.A.
Production of high purity hydrogen from biogas by combined dry reforming of methane and steam iron process (SIP), outlines a serious drawback with the possible formation of coke deposits along reduction steps of the iron oxide. Steam used along reoxidations, which regenerates the iron oxide and force the release of high purity hydrogen, could also be responsible of the gasification of such coke deposits and the consequent contamination of hydrogen with carbonaceous species such as CO or CO2. Oxidations at low enough temperature can inhibit coke gasification, but paradoxically, increasing amounts of coke upon repeated cycles will provoke reactor clogging sooner or later. To circumvent this issue, a strategy consisting of interspersing coke combustion stages with diluted oxygen within the regular cycles of reduction with biogas and reoxidation with steam releasing hydrogen, has been analyzed with three solids based on iron oxide. It has been verified that including coke combustion stages within the regular scheme of redox cycles, not only counteracts both bed clogging and catalyst deactivation by coking, but also breaks down the trend to lose (by sintering) active material for the redox process, thus allowing the extension of the useful life of the solid.