Skip to main content

ESTRATEGIAS DE BAJO COSTE EN LA PRODUCCION DE BIOACEITES PIROLITICOS DE ALTA CALIDAD COMO VECTOR ENERGETICO

ENE2015-68320-R

•
Funding agency name Ministerio de Economía y Competitividad
Funding agency acronym MINECO
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2015
State Plan 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Management unit Dirección General de Investigación Científica y Técnica
Beneficiary centre AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 22
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Catalytic co-pyrolysis of grape seeds and waste tyres for the production of drop-in biofuels

  • Sanahuja-Parejo, Olga
  • Veses Roda, Alberto
  • Navarro López, María Victoria
  • López Sebastián, José Manuel
  • Murillo Villuendas, Ramón
  • Callén Romero, M. Soledad
  • García Martínez, Tomás
© 2018. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Catalytic co-pyrolysis of grape seeds and waste tyres was performed in a fixed-bed reactor using calcined calcite as a catalyst. The organic phase obtained was analysed for its further application as a potential and stable drop-in fuel. Remarkable positive effects were achieved after the joint incorporation of both waste tyres and calcined calcite to grape seeds in the process. More specifically, the addition of considerable amounts of waste tyres (between 20 and 40 wt%) with a constant ratio of feedstock to calcined calcite of 1 were considered the optimal experimental conditions to promote positive synergistic effects on bio-oil yields and its characteristics as a fuel. Thus, when the proportion of waste tyres in the feed reached 40 wt%, the organic phase yield was considerable improved, reaching up values higher than 73 wt%, significantly greater than those obtained from conventional pyrolysis (61 wt%). Moreover, oxygen content was reduced to 4.2 wt%, minimizing any problems related to corrosivity and instability. HHV was enlarged from 15.3 up to 27.3 MJ/kg, significantly increasing the value of the resulting bio-oil. pH values and specially total acid number were also improved reaching values down to 1 mg KOH/gbio-oil in all cases. Additionally, a more valuable chemical composition was achieved since the production of aromatic and cyclic hydrocarbons was maximized, while a significant reduction in phenolic compounds was achieved. Moreover, bio-oil sulphur content was drastically reduced in comparison with the pyrolysis of waste tyres by itself from 0.6 down to 0.2 wt%. The role of calcined calcite was, directly related to the promotion of dehydration reactions of acids and phenols in order to generate hydrocarbons. On the other hand, radical interactions between the biomass and waste tyres pyrolysis products played a fundamental role in the production of more valuable compounds. Finally, the CO2 capture effect produced a more environmentally friendly gas while maintaining its calorific value., The authors would like to thank MINECO and FEDER for their financial support (Project ENE2015-68320-R). The authors would also like to thank the Regional Government of Aragon (DGA) for the support provided under the research groups support programme., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Prediction of elemental composition, water content and heating value of upgraded biofuel from the catalytic cracking of pyrolysis bio-oil vapors by infrared spectroscopy and partial least square regression models

  • Veses Roda, Alberto
  • López Sebastián, José Manuel
  • García Martínez, Tomás
  • Callén Romero, M. Soledad
© 2018. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, The elemental composition, heating value and water content, are important properties to be characterized for pyrolysis bio-oils, providing information on their quality. These properties are mainly determined according to ASTM standards by using three different analytical techniques requiring time and cost. This research was focused on a simple method to determine the weight content of carbon, hydrogen, oxygen and water as well as the heating value, by Fourier transform infrared spectroscopy (FT-IR) using models based on partial least squares regressions (PLS). Samples were classified into two sets according to Kennard-Stone algorithm. The first set of samples was used to develop the calibration models for each physical parameter, where the number of latent variables was determined by full cross validation procedure. The second set of samples was employed as an external prediction set, assessing the quality of the models. External predictions confirmed that robust models were developed since elemental analysis, heating value and water content of the upgraded biofuels obtained by the catalytic cracking of pyrolysis bio-oil vapors could be determined with good predictive ability with a root mean square error of prediction of carbon content=0.963 wt.% (R2=0.836, range=70.9–78.8 wt.%), hydrogen content=0.101 wt.% (R2=0.815, range=8.01-8.75 wt.%), oxygen content=0.910 wt.% (R2=0.873, range=12.3–20.9 wt.%), water content=0.416 wt.% (R2=0.829, range=2.79–7.24 wt.%) and heating value=0.539 MJ kg−1(R2=0.874, range=31.9–36.9 MJ kg−1) by chemometric tools joined to medium infrared spectrum., Authors would like to thank the Spanish MINECO and European Union FEDER funds for supporting this work (projects CTQ2012-37984-C02-01 and ENE2015-68320-R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Kinetic study for the co-pyrolysis of lignocellulosic biomass and plastics using the distributed activation energy model

  • Navarro López, María Victoria
  • López Sebastián, José Manuel
  • Veses Roda, Alberto
  • Callén Romero, M. Soledad
  • García Martínez, Tomás
The characteristics of bio-oil produced from biomass pyrolysis can be improved by co-feeding waste materials. In this work, co-pyrolysis of lignocellulosic biomass with six different waste plastics (waste tyre (WT), polylactic acid (PLA), polystyrene (PS), polyethylene terephthalate (PET), polypropylene (PP) and high density polyethylene (HDPE)) were conducted in a thermogravimetric analyser to study thermal decomposition of the mixtures. The distributed activation energy model (DAEM) was applied to pure feedstocks at 5 and 10 °C/min heating rates to fit the kinetic parameters. The model was used to simulate the co-pyrolysis of biomass/plastic mixtures assuming additive effect of components at different weight proportions and heating rates. Profiles of the fraction of mass remaining for mixtures at 100 °C/min were reproduced with a remarkable agreement. Discrepancies between the experimental and calculated profiles were considered as a measure of the extent of interactions occurring in the co-pyrolysis. Projections of the behaviour of mixtures under flash pyrolysis conditions were performed to study important aspects of the process, such as radical interactions and optimum working temperature, The authors wish to thank the Spanish MINECO and European Union FEDER funds (project ENE2015-68320-R) and the Regional Government of Aragon (DGA) for the research groups support programme (project T04_17R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Understanding the role of Ti-rich domains in the stabilization of gold nanoparticles on mesoporous silica-based catalysts

  • Moragues, Alaina
  • Puértolas Lacambra, Begoña
  • Mayoral, Álvaro
  • Arenal, Raúl
  • Hungría, Ana B.
  • Murcia-Mascarós, Sonia
  • Taylor, Stuart H.
  • Solsona, Benjamín
  • García Martínez, Tomás
  • Amorós, Pedro
3 Tablae, 14 Figures.-- Supplementary material.-- © 2018. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, The preparation and stabilization of gold nanoparticles with a precise control of size and dispersion is highly attractive for a variety of applications, and a key aspect is thermal stability of the nanoparticles. This paper focuses on understanding the effect of TiO2-based nanodomains, dispersed on mesoporous silicas, and how they control gold nanoparticle stability. The anatase domains have been incorporated through two different strategies: co-hydrolysis of Si and Ti reagents that directly form the mesoporous material through self-assembling with surfactant micelles, or the post-impregnation of the mesosporous silica with Ti(acac)2. Both strategies lead to different incorporation of the anatase domains: partially embedded inside the silica walls, or occupying the mesopores. We have observed that the inclusion in the pores favors the stability of the final material due to a more favorable gold-support interaction and also due to a stabilizing effect associated with a scaffold effect of the anatase crystals, which hinders the collapse of the mesostructure., This research was supported by the Spanish Ministerio de Economia y Competitividad and European Feder Funds (MAT2015-64139-C4-3-R, ENE2015-68320-R). The TEM measurements were performed in the Laboratorio de Microscopias Avanzadas (LMA) at the Instituto de Nanociencia de Aragon (INA) - Universidad de Zaragoza (Spain) and received funding from the European Union Seventh Framework Program under Grant Agreement 312483 - ESTEEM2 (Integrated Infrastructure Initiative - I3). B. Puértolas thanks the Ministry of Education for FPU grant (FPU grant AP2009-3544). A. Moragues thanks the Ministry of Economia y Competitividad for FPI grant (FPI grant BES2009-040029). UV is also acknowledged by the UV-INV-AE16-484416 project., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Pyrolysis kinetics of biomass wastes using isoconversional methods and the distributed activation energy model

  • Arenas, Cindy Natalia
  • Navarro López, María Victoria
  • Martínez Ángel, Juan Daniel
7 Figures, 4 Tables.-- © 2019. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, In this work, a thermogravimetric analyser was used to assess the pyrolysis kinetics of pineapple, orange and mango peel wastes and agro-industrial by-products, rice husk and pine wood. Five isoconversional methods (KAS, FWO, Starink, Vyazovkin and Friedman) and one model-fitting method (DAEM) accurately fitted the experimental data at three heating rates (5, 10 and 20 °C/min) between 10% and 90% conversion. These methods agree with the trends shown by the activation energy (Ea) distribution calculated, with fluctuations between 150 and 550 kJ/mol. The fluctuations of Ea in the whole range of conversion, in addition to a higher number of relevant reactions obtained by DAEM for fruit peel samples compared to agro-industrial samples, are associated with a higher extractive content in the peels. Kinetic parameters fitted by DAEM were successfully verified at the highest heating rate studied., The authors would like to express all their gratitude to COLCIENCIAS and CIDI-UPB for the financial support given by the projects 1210-715-51742 and 387C-11/18-24, respectively. We are also grateful to GIMEL group from UdeA for making the TGA device available to us, and to the GRAIN group from UPB for their support in extractives quantification. In addition, the authors would like to thank MINECO and FEDER for their financial support (Project ENE2015-68320-R) and the Regional Government of Aragon (DGA) for the support provided under their research groups support programme., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Production and droplet combustion characteristics of waste tire pyrolysis oil

  • Muelas, Álvaro
  • Callén Romero, M. Soledad
  • Murillo Villuendas, Ramón
  • Ballester, Javier
7 Figures, 4 Tables.-- © 2019. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, This work aims to study the pyrolysis of scrap tires as an end-to-end process, from its production to the combustion characteristics of the tire pyrolysis liquid (TPL) obtained. The TPL was produced in a continuous auger reactor (150 kWth) and its combustion characteristics were acquired through a drop tube facility, where the TPL burning behavior was compared to that of conventional heating oil (FO). The evaluated combustion characteristics included droplet and flame size evolution, burning rates, soot shell morphology, microexplosion occurrence and soot analysis. When compared to FO, TPL displayed considerably lower burning rates, although the consistent occurrence of microexplosions effectively shortened the TPL droplets lifetimes below those of FO. TPL also presented smaller flames and a higher propensity to soot. A TPL-FO blend of interest for heating applications (with only 5% of TPL due to its high sulfur content), was also tested, showing identical results to those of neat FO for all the studied combustion characteristics. The reported results are thought to provide valuable experimental data regarding the combustion behavior of a well characterized tire pyrolysis oil, which could also be used as the fuel-specific input data required for the simulation of realistic spray flames., The authors acknowledge the support of the Spanish Ministry of Education (pre-doctoral grant FPU15/01866) and the Spanish MINECO and European Union FEDER funds through the research projects ENE2016-76436-R and ENE2015-68320-R. The economic support of the Aragon Regional Government (DGA) through the research groups funding programme is acknowledged as well., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

A combined two-stage process of pyrolysis and catalytic cracking of municipal solid waste for the production of syngas and solid refuse-derived fuels

  • Veses Roda, Alberto
  • Sanahuja-Parejo, Olga
  • Callén Romero, M. Soledad
  • Murillo Villuendas, Ramón
  • García Martínez, Tomás
5 Figuras, 4 Tablas.-- Información suplementaria disponible en línea en la página web del editor.-- © 2019. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Pyrolysis combined to either thermal cracking or catalytic cracking of municipal solid waste was performed in a laboratory-scale facility consisting of a fixed-bed reactor followed by a tubular cracking reactor. The results showed great potential for the production of syngas. The incorporation of inexpensive and widely available dolomite in the cracking reactor (with a constant feedstock to calcined dolomite ratio of 5:1) favoured the catalytic cracking of the primary pyrolysis products towards H2 and CO in a temperature range of 800–900 °C. More particularly, it was possible at 900 °C to achieve a syngas consisting of more than 80 vol% CO and H2 with a heating value of 16 MJ/Nm3. Additionally, a homogeneous solid fuel was obtained as a solid residue, which can be used to provide additional energy to support the process or as a refuse-derived fuel. Thus, the great potential of this process was demonstrated for turning municipal solid waste into a valuable gas fraction that can be used directly as a fuel or as a source of different value-added products., The authors would like to thank MINECO and FEDER for their financial support (Project ENE2015-68320-R). O.S.P acknowledges the FPI fellowship (BES-2016-077750) funded by MINECO. The authors would also like to thank the Regional Government of Aragon (DGA) for the support provided under the research groups support programme., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Ca-based catalysts for the production of high-quality bio-oils from the catalytic co-pyrolysis of grape seeds and waste tyres

  • Sanahuja-Parejo, Olga
  • Veses Roda, Alberto
  • López Sebastián, José Manuel
  • Murillo Villuendas, Ramón
  • Callén Romero, M. Soledad
  • García Martínez, Tomás
4 Figuras,7 Tablas.-- Material suplementario disponible en línea en http://www.mdpi.com/2073-4344/9/12/992/s1, The catalytic co-pyrolysis of grape seeds and waste tyres for the production of high-quality bio-oils was studied in a pilot-scale Auger reactor using different low-cost Ca-based catalysts. All the products of the process (solid, liquid, and gas) were comprehensively analysed. The results demonstrate that this upgrading strategy is suitable for the production of better-quality bio-oils with major potential for use as drop-in fuels. Although very good results were obtained regardless of the nature of the Ca-based catalyst, the best results were achieved using a high-purity CaO obtained from the calcination of natural limestone at 900 °C. Specifically, by adding 20 wt% waste tyres and using a feedstock to CaO mass ratio of 2:1, a practically deoxygenated bio-oil (0.5 wt% of oxygen content) was obtained with a significant heating value of 41.7 MJ/kg, confirming its potential for use in energy applications. The total basicity of the catalyst and the presence of a pure CaO crystalline phase with marginal impurities seem to be key parameters facilitating the prevalence of aromatisation and hydrodeoxygenation routes over the de-acidification and deoxygenation of the vapours through ketonisation and esterification reactions, leading to a highly aromatic biofuel. In addition, owing to the CO2-capture effect inherent to these catalysts, a more environmentally friendly gas product was produced, comprising H2 and CH4 as the main components., This research was funded by MINECO and FEDER for their financial support (Project ENE2015-68320-R) and the Regional Government of Aragon (DGA) under the research groups call., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Drop-in biofuels from the co-pyrolysis of grape seeds and polystyrene

  • Sanahuja-Parejo, Olga
  • Veses Roda, Alberto
  • Navarro López, María Victoria
  • López Sebastián, José Manuel
  • Murillo Villuendas, Ramón
  • Callén Romero, M. Soledad
  • García Martínez, Tomás
9 Figuras, 4 Tablas.-- Material suplementario disponible en línea en la página web del editor., Co-pyrolysis of grape seeds and polystyrene was conducted in a fixed-bed reactor, followed by an analysis of the organic phase for possible further application as a drop-in fuel. Significant positive synergistic effects were found with the addition of polystyrene (5–40 wt%) to the conventional pyrolysis of grape seeds. There was a considerable improvement in the organic phase yield, in particular, reaching values over 80 wt%, markedly higher than those obtained from conventional pyrolysis (61 wt%). Fuel properties of the bio-oil were also upgraded, with a decrease in oxygen content and an increase in the heating value. An organic bio-oil fraction with pH values ranging from 5.4 to 6.2 was obtained, reducing the issues associated with handling bio-oils obtained from common pyrolysis of lignocellulosic biomass, usually ranging pH between 2 and 3. Finally, an increment in the desired compounds, mainly aromatics, was also attained, while at the same time achieving a low content of undesired compounds, such as phenols. It was demonstrated that polystyrene can act as a H2-donor, favoring oligomerization, cyclation and hydrodeoxygenation reactions into aromatic compounds., The authors would like to thank MINECO and FEDER for their financial support (Project ENE2015-68320-R). O.S.P acknowledges the FPI fellowship (BES-2016-077750) funded by MINECO. The authors would also like to thank the Regional Government of Aragon (DGA) for the support provided under the research groups support programme., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Application of upgraded drop-in fuel obtained from biomass pyrolysis in a spark ignition engine

  • Veses Roda, Alberto
  • Martínez Ángel, Juan Daniel
  • Callén Romero, M. Soledad
  • Murillo Villuendas, Ramón
  • García Martínez, Tomás
5 figures, 2 tables, This paper reports the performance of a spark ignition engine using gasoline blended with an upgraded bio-oil rich in aromatics and ethanol. This upgraded bio-oil was obtained using a two-step catalytic process. The first step comprised an in-situ catalytic pyrolysis process with CaO in order to obtain a more stable deoxygenated organic fraction, while the second consisted of a catalytic cracking of the vapours released using ZSM-5 zeolites to obtain an aromatics-rich fraction. To facilitate the mixture between bio-oil and gasoline, ethanol was added. The behaviour of a stationary spark ignition engine G12TFH (9600 W) was described in terms of fuel consumption and electrical efficiency. In addition, gaseous emissions and polycyclic aromatic hydrocarbon (PAH) concentrations were determined. Trial tests suggested that it is possible to work with a blend of gasoline, ethanol and bio-oil (90/8/2 vol%, herein named G90E8B2) showing similar fuel consumption than pure gasoline (G100) at the same load. Moreover, combustion could be considered more efficient when small quantities of ethanol and organic bio-oil are simultaneously added. A reduction, not only in the PAH concentrations but also in the carcinogenic equivalent concentrations, was also obtained, decreasing the environmental impact of the exhaust gases. Thus, results show that it is technically feasible to use low blends of aroma-rich bio-oil, ethanol and gasoline in conventional spark ignition engines., This research was funded by MINECO and FEDER (Project ENE2015-68320-R) and the Regional Government of Aragon (DGA) under the research groups support programm, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Glycerol selective oxidation to lactic acid over AuPt nanoparticles; Enhancing reaction selectivity and understanding by support modification

  • Douthwaite, Mark
  • Powell, Natasha
  • Taylor, Aoife
  • Ford, Grayson
  • López Sebastián, José Manuel
  • Solsona, Benjamín
  • Yang, Nating
  • Sanahuja-Parejo, Olga
  • He, Quian
  • Morgan, David J.
  • García Martínez, Tomás
  • Taylor, Stuart H.
2 Schemes, 3 Tables, 5 Figures., A high surface area mesoporous TiO2 material (110 m2/g) was synthesised using a nanocasting methodology, utilizing SBA‐15 as a hard template. This material was subsequently used as a support to prepare a series of 1 wt.% AuPt/TiO2 catalysts, synthesised by conventional impregnation and sol‐immobilisation. Catalysts were tested for the oxidation of glycerol to lactic acid and their performance was compared with corresponding catalysts supported on TiO2−P25, TiO2‐anatase and TiO2‐rutile. Higher rates of reaction and higher selectivity to lactic acid were observed over nanocast TiO2 supported catalysts. The increased performance of these catalysts was attributed to the presence of Si on the surface of the support, which likely arose from inefficient etching of the SBA‐15 template. The presence of Si in these catalysts was confirmed by X‐ray photoelectron spectroscopy and electron energy loss spectroscopy. It was proposed that the residual Si present increases the Brønsted acidity of the TiO2 support, which can lead to the formation of Lewis acid sites under reaction conditions; both sites are known to catalyse the dehydration of a primary alcohol in glycerol. Typically, under alkaline conditions, lactic acid is formed by the nucleophilic abstraction of a hydrogen. Thus, we propose that the improved selectivity to lactic acid over the nanocast TiO2 supported catalyst is attributed to the co‐operation of heterogeneous and homogeneous dehydration reactions, as both compete directly with a direct oxidation pathway, which leads to the formation of oxidation products such as glyceric and tartronic acid., T. García would like to acknowledge the Spanish MICINN through its Mobility program for stays of senior researchers and professors in foreign countries (grant number PRX18/00474) for funding. O.S.P acknowledges the FPI fellowship (BES-2016-077750) funded by Spanish MINECO. B.S. also thank MINECO (MAT2017-84118-C2-1-R project) for funding. We would also like to thank the Cardiff University TEM facility for the TEM and FEG-SEM electron microscopy data acquired and Diamond Light Source for access and support in use of the electron Physical Science Imaging Centre (Instrument E01 and proposal number MG21641 and MG22766) which contributed to the results presented here., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

From laboratory scale to pilot plant: Evaluation of the catalytic co-pyrolysis of grape seeds and polystyrene wastes with CaO

  • Veses Roda, Alberto
  • Sanahuja-Parejo, Olga
  • Navarro López, María Victoria
  • López Sebastián, José Manuel
  • Murillo Villuendas, Ramón
  • Callén Romero, M. Soledad
  • García Martínez, Tomás
5 figures, 5 tables.-- Supplementary information available.-- © 2020. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, The catalytic co-pyrolysis of grape seeds and polystyrene was successfully scaled-up from thermogravimetric analysis to an auger reactor pilot plant. Agricultural residues were co-pyrolyzed with waste polystyrene plastics (up to 20 wt%) using calcium oxide as the catalyst. Particularly, an upgraded organic fraction was produced where synergetic positive effects were observed due to both the presence of plastics and of the CaO catalyst. These effects were mainly reflected in the production of a more deoxygenated and practically dehydrated organic fraction, rich in aromatic compounds and with a remarkable heating value. The synergetic positive effect of these materials is mainly attached to the promotion of the H2 transfer reactions resulting from the scission of polystyrene radicals, and from the decarboxylation and dehydration effects associated with CaO. Moreover, a non-condensable H2-rich gas stream with remarkably low CO2 concentration, proved potentially valuable not only for use in further energetic applications but also as a potential source of synthetic fuels. The great potential of this process in the production of bio-products was, thus, demonstrated in a representative scale., The authors would like to thank MINECO and FEDER for their financial support (Project ENE2015-68320-R). O.S.P acknowledges the FPI fellowship (BES-2016-077750) funded by MINECO. The authors would also like to thank the Regional Government of Aragon (DGA) for the support provided under the research groups support programme., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

An integrated process for the production of lignocellulosic biomass pyrolysis oils using calcined limestone as a heat carrier with catalytic properties

  • Veses Roda, Alberto
  • Aznar, María
  • Callén Romero, M. Soledad
  • Murillo Villuendas, Ramón
  • García Martínez, Tomás
4 figures, 2 tables.-- Supplementary information available.-- © 2016. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, The production of upgraded bio-oils by an integrated process using a mixture of calcined limestone and sand as a heat carrier with catalytic properties was experimentally studied at pilot scale. The integrated process consisted of two main steps: biomass catalytic pyrolysis in an Auger reactor for bio-oil production and char combustion in a fluidised-bed combustor for heat carrier heating and regeneration. A temperature of 450 °C was fixed as an optimum value to carry out the catalytic pyrolysis step. Temperatures ranging from 700 to 800 °C were assessed in the char combustor. Process simulation demonstrated that solid recirculation from the combustor to the pyrolysis reactor was marginally affected in this temperature range. However, an optimum char combustion temperature of 800 °C was selected from an environmental point of view, since lower polyaromatic emissions were detected whilst NOx emissions were kept under the legislation limits. Under designated conditions, several pyrolysis-combustion cycles were carried out. A moderate deactivation of the catalyst by partial carbonation was found. This fact makes necessary the incorporation of a purge and an inlet of fresh heat carrier in order to maintain the bio-oil quality in the integrated process., Authors thank to Spanish MINECO and European Union FEDER funds for providing support for this work (projects CTQ2012-37984-C02-01 and ENE2015-68320-R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Insights into the production of upgraded biofuels using Mg-loaded mesoporous ZSM-5 zeolites

  • Sanahuja-Parejo, Olga
  • Veses Roda, Alberto
  • López Sebastián, José Manuel
  • Callén Romero, M. Soledad
  • Solsona, Benjamín
  • Richards, Nia
  • Taylor, Stuart H.
  • García Martínez, Tomás
9 figures, 6 tables.-- Supplementary information available.-- https://authorservices.wiley.com/author-resources/Journal-Authors/licensing/self-archiving.html, Bio‐oil catalytic upgrading has been performed using mesoporous Mg‐loaded ZSM‐5. The presence of Mg modifies both textural and acidic properties, which do not only depend on the Mg content (1 and 5 wt. %) but also on the Si/Al ratio of the parent zeolite (25 and 40). Mg impregnation over mesoporous acidic zeolites has been shown to be essential for further deoxygenation of the raw bio‐oil. Thus, remarkable deoxygenation rates have been achieved, exceeding 68 % for a 5 wt. % Mg‐loaded ZSM‐5 (Si/Al=25). For this catalyst, decarboxylation reactions at MgO active sites seem to be predominant, promoting the upgrading of phenols towards the formation of phenolic compounds with lower oxygen content. As in the case of acidic mesoporous ZSM‐5, the formation of aromatics for Mg‐loaded mesoporous ZSM‐5 samples could be mainly related to the promotion of decarbonylation reactions of phenolic compounds over Brønsted acidic sites at the external surface. Interestingly, the presence of strong Lewis acidic sites created by the interaction between (Mg2+OH−)+ species and extra framework alumina jointly with the remaining Brønsted acidic sites at the external surface could enhance the formation of aromatics through cascade reactions involving ketonization and further aldol condensation and dehydration reactions, The authors would like to thank MINECO and FEDER for financial support (Project ENE2015‐68320‐R and MAT2017‐84118‐C2‐1‐R). The authors want also to thank the support from the Regional Aragon Government (DGA) under the research groups support program., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

A pyrolysis process coupled to a catalytic cracking stage: A potential waste-to-energy solution for mattress foam waste

  • Veses Roda, Alberto
  • Sanahuja-Parejo, Olga
  • Martínez Berges, Isabel
  • Callén Romero, M. Soledad
  • López Sebastián, José Manuel
  • García Martínez, Tomás
  • Murillo Villuendas, Ramón
3 figures, 5 tables.-- Supplementary information available.-- © 2020. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, Pyrolysis coupled to either thermal or catalytic cracking of mattress foam waste was performed in a laboratory-scale facility consisting of a fixed-bed reactor joined to a tubular cracking reactor. The results showed a great potential for the production of syngas specially at high cracking temperatures. Particularly, fixing 800 °C in the cracking reactor, a CO and CH4 rich gas with a remarkable amount of H2 was obtained. The addition of catalysts (dolomite, olivine or HiFUEL®) significantly decreased undesirable tar formation, (below 10 wt%), simultaneously increasing the gas yield and keeping CO and CH4 as the main components in the stream, becoming a preferable route that the non-catalytic process. Accordingly, this stream could be used preferably for further applications in energy generation because its heating value ranged between 15.7 MJ/Nm3 and 19.6 MJ/Nm3. In particular, the gas obtained by the use of dolomite could be advantageous for the production of organic compounds such as dimethyl ether (DME) as well as its use an engine or boiler to generate electricity in small facilities. In addition, the solid fraction obtained after de process could be used as a medium quality refused derived fuel (LHV ~ 12 MJ/kg) in order to support the internal energy requirements of the process., The authors would like to thank MINECO and FEDER for their financial support (Project ENE2015-68320-R). O.S.P acknowledges the FPI fellowship (BES-2016-077750) funded by MINECO. The authors would also like to thank the Regional Government of Aragon (DGA) for the support provided under the research groups support programme and to CSIC through interdisciplinary thematic platform SUSPLAST., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Catalytic co-pyrolysis of grape seeds and waste tyres as a low cost strategy in the production of hight quality bio-oils

  • Veses Roda, Alberto
  • Sanahuja-Parejo, Olga
  • Callén Romero, M. Soledad
  • García Martínez, Tomás
3 figures, 2 tables.-- Poster presented at the 4th International Congress on Catalysis for Biorefineries (CatBior), December 2017, 11th-15th, Lyon (France)., The concept of biorefinery emerges as a promising alternative to reduce environmental impact caused by extraction and processing of fossil fuels In that sense, the use of renewable sources and, more specifically, the use of lignocellulosic biomass is one of the best promising alternatives since it is the only carbon containing renewable source that can produce biofuels similar to fossil fuels and it does not compete with food production Among all the processes that can valorize lignocellulosic biomass, pyrolysis is an attractive alternative because it is the only thermochemical process that can produce a liquid biofuel (bio oil) in a simple way and solid and gas fractions that can be used as energy sources to support the process. However, in order to incorporate bio oils in current infrastructures and further processing in future biorefineries, their quality needs to be improved Introducing different low cost catalysts and/or incorporating different plastic residues to the process are some of the possibilities to achieve this aim in an economic way. The implementation of new, simple and low-cost strategy through catalytic co-pyrolysis of grape seeds and waste tyres using CaO as a catalyst in a specifically designed fixed-bed reactor, that allows the user to directly obtain high quality bio-oils to be used as renewable energetic vector., The authors would like to thank MINECO y FEDER for financial support (Project ENE2015-68320-R), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Zeolitas ZSM 5 mesoporosas: Avances hacia la producción de biocombustibles de segunda generación

  • Sanahuja-Parejo, Olga
  • Veses Roda, Alberto
  • Callén Romero, M. Soledad
  • García Martínez, Tomás
Póster presentado en la XIV Reunión del Grupo Español del Carbón, celebrada del 22 al 25 de Octubre de 2017 - Málaga, España., Los biocombustibles de segunda generación, en concreto aquellos producidos a partir de la pirólisis de biomasa de tipo lignocelulósico, pueden ser considerados como una importante fuente de energía para minimizar el negativo impacto medioambiental causado por el uso y la extracción de los combustibles fósiles. Sin embargo, para asegurar la viabilidad del proceso, es necesario mejorar sus prestaciones con el objetivo de obtener un biofuel compatible con las actuales infraestructuras. Para ello, en este estudio hemos planteado un proceso de craqueo catalítico usando zeolitas tipo ZSM 5 mesoporosas impregnadas con Mg a diferentes cargas 1 y 5 y mediante dos métodos diferentes de impregnación de una zeolita mesoporosa ácida previamente sintetizada en el laboratorio (impregnación seca e impregnación húmeda), como estrategia para la obtención de biocombustibles de segunda generación de mejor calidad. Se ha podido observar que en todos los casos se obtiene un biofuel de mejores prestaciones, llegando a obtener tasas de reducción de oxígeno de mas de un 65 en comparación al 44 obtenido mediante la zeolita mesoporosa ácida de partida. Este mayor ratio de desoxigenación se ha asociado a la acción de los nuevos sitios ácidos de Lewis creados por los cationes de Mg presentes en las posiciones de intercambio. A través de estos nuevos puntos activos se favorecen tanto las reacciones de cetonización especialmente entre ácidos y aldehídos para dar cetonas, como las reacciones de esterificación de ácidos y alcoholes, tal y como reflejan la mayor producción de ésteres y cetonas en los biofuels así como el aumento de producción de CO 2 en los gases del proceso., Los autores agradecen a MINECO y FEDER por su financiación para llevar a cabo este trabajo (proyecto ENE2015-68320-R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Improved bio-oils from in situ co-pyrolysis of grape seeds and polystyrene

  • Sanahuja-Parejo, Olga
  • Veses Roda, Alberto
  • López Sebastián, José Manuel
  • Navarro López, María Victoria
  • Callén Romero, M. Soledad
  • García Martínez, Tomás
7 figures, 2 tables.-- Poster presented at the 25th International Conference on Chemical Reaction Engineering (ISCRE 25 2018), 2018, May 20th-23rd, Florence (Italy)., The effective use of renewable sources to produce energy is an important objective to reduce the environmental impact caused by the exploitation of fossil fuels. The use of lignocellulosic biomass becomes one of the most promising alternatives, as it is the only renewable source of carbon that can produce products similar to fossil fuels through the pyrolysis process and does not compete with the food market. Unfortunately, the properties of pyrolytic bio oils as fuels are very poor and different improvement strategies need to be implemented. Among all the strategies, co pyrolysis of biomass and plastic waste such as polystyrene ( emerges as a promising way to achieve this goal). For synergistic reasons these raw materials are processed by co pyrolysis giving the process the possibility to achieve this objective economically. The present work develops a new and low cost strategy based on the in situ co pyrolysis of biomass and plastic wastes that allows the user to obtain an advanced bio oil to be used directly or to be processed in bio refineries. The implementation of new, simple and low cost strategy through co pyrolysis of grape seeds and PS in a specifically designed fixed bed reactor, that allows the user to directly obtain high quality bio oils to be used as renewable energetic vector., The authors would like to thank MINECO and FEDER for financial support (Project ENE2015-68320-R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Properties and combustion characteristics of bio-oils from catalytic co-pyrolysis of grape seeds, polystyrene, and waste tires

  • Muelas, Álvaro
  • Aranda, Diego
  • Callén Romero, M. Soledad
  • Murillo Villuendas, Ramón
  • Veses Roda, Alberto
  • Mohamad, Asrardel
  • Ballester, Javier
9 figures, 3 tables.-- This document is the Accepted Manuscript version of a Published Work that appeared in final form in ENERGY & FUELS, copyright © American Chemical Society after peer review and technical editing by the publisher. To access the final edited and published work see http://dx.doi.org/10.1021/acs.energyfuels.0c02257., This work aims to study the bio-oils obtained from the catalytic co-pyrolysis of waste polymers and a residual biomass (grape seeds, GS). For that purpose, the organic liquid fractions produced in an auger reactor were thoroughly characterized in two steps, obtaining in the first place their main physicochemical properties as well as their chemical compositions, and second, their droplet combustion behaviors. Both the polymer type (waste tires or polystyrene, WT and PS, respectively) and the nature of the low-cost, calcium-based catalyst used (Carmeuse limestone, calcined dolomite, or an inert material such as sand) were studied. A significant improvement in the physicochemical properties of the bio-oils was obtained when using a catalyst, with lower viscosity, density, and oxygen content. These beneficial effects were more marked for the bio-oil produced with the Carmeuse catalyst, presumably due to the higher prevalence of aromatization and hydro-deoxygenation reactions. When changing the polymer source from WT to PS, a considerable increase in the aromatic content and a viscosity reduction were noted. The droplet combustion tests revealed the consistent occurrence of microexplosions for all of the studied bio-liquids, these bursting events being more violent for the GS–PS oil. Regarding the evaporation behavior, this liquid also yielded significantly higher burning rates during the initial heat-up phase, in agreement with its richer composition in volatile compounds such as styrene. These results point to this fuel as the one with the best global combustion behavior from all of the explored bio-oils. The GS–WT liquids showed much closer features among them, although with noticeable differences depending on the catalyst used. A more volatile behavior was observed for GS–WT Carmeuse, followed by GS–WT dolomite and GS–WT sand, strengthening thus the previously reported improvements in physicochemical properties. Finally, the propensity to form soot of these bio-oils was characterized through a soot probe, which revealed a higher soot yield for the bio-liquids produced with the Carmeuse catalyst., This work was financed by the Spanish Ministry of Economy, Industry, and Competitiveness and EU FEDER funds through research projects ENE2016-76436-R and ENE2015-68320-R, the Spanish Ministry of Education through the predoctoral grant FPU15/01866, and the Regional Government of Aragon (DGA) under the research group call., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Ca-based catalysts for the production of high-quality bio-oils from the catalytic co-pyrolysis of grape seeds and waste tyres

  • Sanahuja-Parejo, Olga
  • Veses, Alberto
  • López, José Manuel
  • Murillo, Ramón
  • Callén, María Soledad
  • García, Tomás
The catalytic co-pyrolysis of grape seeds and waste tyres for the production of high-quality bio-oils was studied in a pilot-scale Auger reactor using different low-cost Ca-based catalysts. All the products of the process (solid, liquid, and gas) were comprehensively analysed. The results demonstrate that this upgrading strategy is suitable for the production of better-quality bio-oils with major potential for use as drop-in fuels. Although very good results were obtained regardless of the nature of the Ca-based catalyst, the best results were achieved using a high-purity CaO obtained from the calcination of natural limestone at 900 degrees C. Specifically, by adding 20 wt% waste tyres and using a feedstock to CaO mass ratio of 2:1, a practically deoxygenated bio-oil (0.5 wt% of oxygen content) was obtained with a significant heating value of 41.7 MJ/kg, confirming its potential for use in energy applications. The total basicity of the catalyst and the presence of a pure CaO crystalline phase with marginal impurities seem to be key parameters facilitating the prevalence of aromatisation and hydrodeoxygenation routes over the de-acidification and deoxygenation of the vapours through ketonisation and esterification reactions, leading to a highly aromatic biofuel. In addition, owing to the CO2-capture effect inherent to these catalysts, a more environmentally friendly gas product was produced, comprising H-2 and CH4 as the main components.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Catalytic co-pyrolysis of grape seeds and waste tyres for the production of drop-in biofuels

  • Sanahuja-Parejo, Olga
  • Veses Roda, Alberto
  • Navarro López, M. Victoria
  • López Sebastián, José Manuel
  • Murillo Villuendas, Ramón
  • Callén Romero, M. Soledad
  • García Martínez, Tomás
Catalytic co-pyrolysis of grape seeds and waste tyres was performed in a fixed-bed reactor using calcined calcite as a catalyst. The organic phase obtained was analysed for its further application as a potential and stable drop-in fuel. Remarkable positive effects were achieved after the joint incorporation of both waste tyres and calcined calcite to grape seeds in the process. More specifically, the addition of considerable amounts of waste tyres (between 20 and 40 wt%) with a constant ratio of feedstock to calcined calcite of 1 were considered the optimal experimental conditions to promote positive synergistic effects on bio-oil yields and its characteristics as a fuel. Thus, when the proportion of waste tyres in the feed reached 40 wt%, the organic phase yield was considerable improved, reaching up values higher than 73 wt%, significantly greater than those obtained from conventional pyrolysis (61 wt%). Moreover, oxygen content was reduced to 4.2 wt%, minimizing any problems related to corrosivity and instability. HHV was enlarged from 15.3 up to 27.3 MJ/kg, significantly increasing the value of the resulting bio-oil. pH values and specially total acid number were also improved reaching values down to 1 mg KOH/gbio-oil in all cases. Additionally, a more valuable chemical composition was achieved since the production of aromatic and cyclic hydrocarbons was maximized, while a significant reduction in phenolic compounds was achieved. Moreover, bio-oil sulphur content was drastically reduced in comparison with the pyrolysis of waste tyres by itself from 0.6 down to 0.2 wt%. The role of calcined calcite was directly related to the promotion of dehydration reactions of acids and phenols in order to generate hydrocarbons. On the other hand, radical interactions between the biomass and waste tyres pyrolysis products played a fundamental role in the production of more valuable compounds. Finally, the CO2 capture effect produced a more environmentally friendly gas while maintaining its calorific value.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

A combined two-stage process of pyrolysis and catalytic cracking of municipal solid waste for the production of syngas and solid refuse-derived fuels

  • Veses, Albert
  • Sanahuja-Parejo, Olga
  • Callén, María Soledad
  • Murillo, Ramón
  • García, Tomás
Pyrolysis combined to either thermal cracking or catalytic cracking of municipal solid waste was performed in a laboratory-scale facility consisting of a fixed-bed reactor followed by a tubular cracking reactor. The results showed great potential for the production of syngas. The incorporation of inexpensive and widely available dolomite in the cracking reactor (with a constant feedstock to calcined dolomite ratio of 5:1) favoured the catalytic cracking of the primary pyrolysis products towards H2 and CO in a temperature range of 800–900 C. More particularly, it was possible at 900 C to achieve a syngas consisting of more than 80vol% CO and H2 with a heating value of 16MJ/Nm3. Additionally, a homogeneous solid fuel was obtained as a solid residue, which can be used to provide additional energy to support the process or as a refuse-derived fuel. Thus, the great potential of this process was demonstrated for turning municipal solid waste into a valuable gas fraction that can be used directly as a fuel or as a source of different valueadded products.