Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Ageing and seasonal effects on amorphous silicon photovoltaic modules in a Mediterranean climate

  • Mateo, C.
  • Hernández Fenollosa, María De Los Ángeles|||0000-0001-8003-3651
  • Montero Reguera, Álvaro Enrique|||0000-0002-4165-4743
  • Segui-Chilet, Salvador|||0000-0002-2927-6938
[EN] This contribution presents afield study in which the long-term behaviour of two a-Si photovoltaic plants is studied. Two grid-connected a-Si:H photovoltaic plants located in Valencia (Spain) have been monitored during their first eight years of operation under real outdoor conditions. A per-unit approachand an STC normalisation have been made to analyse and compare photovoltaic plants with differences in electrical characteristics. An averaging process of the filtered and normalised data produces a monthly averaged value that is used to evaluate the ageing and seasonal effects experienced by the two photovoltaic plants. An analysis of the variations in the per unit output power finds that a seasonal effect is superimposed on the long-term stabilisation process. The study concludes that the long-term average stabilisation factor is equal to 1,35% per year, with a seasonal effect that shows a sinusoidal variation with an average amplitude of the sinusoidal oscillation equal to 2,71% per year. An estimation of the energy yield is performed considering the different ageing approaches presented in the study. Using the factors obtained from the experimental values, the ageing and seasonal effects are modelized, and a linear and an exponential expression is proposed to fit the long-term behaviour of both a-Si photovoltaic plants. Results obtained with the statistical analysis are compared with the experimental data and it is found that the exponential behaviour matches the experimental values., The authors would like to thank the support of the European Union through the European Regional Development Funds (ERDF), the Spanish Ministry of Economy, Industry and Competitiveness, for the research project POLYDECARBOCELL (ENE2017-86711-C3-1-R) and the Generalitat Valenciana, Spain (PROMETEO/2020/077).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Proton Conductivity through Polybenzimidazole Composite Membranes Containing Silica Nanofiber Mats

  • Escorihuela, Jorge
  • Andrio, Andreu
  • Garcia-Bernabe, Abel|||0000-0002-9740-0830
  • Montero Reguera, Álvaro Enrique|||0000-0002-4165-4743
  • Sahuquillo, Oscar|||0000-0001-5360-3743
  • Giménez Torres, Enrique|||0000-0002-6330-0209
  • Compañ Moreno, Vicente|||0000-0001-8233-7472
[EN] The quest for sustainable and more efficient energy-converting devices has been the focus of researchers 0 efforts in the past decades. In this study, SiO2 nanofiber mats were fabricated through an electrospinning process and later functionalized using silane chemistry to introduce different polar groups OH (neutral), SO3H (acidic) and NH2 (basic). The modified nanofiber mats were embedded in PBI to fabricate mixed matrix membranes. The incorporation of these nanofiber mats in the PBI matrix showed an improvement in the chemical and thermal stability of the composite membranes. Proton conduction measurements show that PBI composite membranes containing nanofiber mats with basic groups showed higher proton conductivities, reaching values as high as 4 mS.cm(-1) at 200 degrees C., This research was funded by the Spanish Ministerio de Economia y Competitividad (MINECO) for the financial support, grant number ENE/2015-69203-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Polymer-modified sulfonated PEEK ionomer membranes and the use of Ru3Pd6Pt as cathode catalyst for H2/O2 fuel cells

  • Martínez-Casillas, Diana
  • Solorza, Omar
  • Mollá Romano, Sergio
  • Montero Reguera, Álvaro Enrique|||0000-0002-4165-4743
  • Garcia-Bernabe, Abel|||0000-0002-9740-0830
  • Compañ Moreno, Vicente|||0000-0001-8233-7472
[EN] Nanocomposite membranes incorporating electrospun nanofibers of SPEEK, blended with 30 wt% PVB within a water-based matrix of SPEEK with 35 wt% PVA using water as solvent, were prepared and characterized for their application as Polymer Electrolyte Membrane Fuel Cells (PEMFCs) in H-2/O-2 operating at low temperatures. Compared with a dense bulk phase, an improvement of proton conductivity in the SPEEK-30PVB nanofiber framework was observed. The incorporation of the SPEEK-30PVB nanofibers provides mechanical improvement while the matrix phase of SPEEK-35PVA emphasizes the proton conductivity at crosslinking temperatures up to 140 degrees C. PEMFC performance tests showed promising results for the use of these novel low cost membranes. The nanocomposite membrane reached a power density which is 25% higher than that of Nafion117 membranes with MEAs constructed with Pt loading in anode and in cathode. However, when the Pt of the cathode is substituted by Ru3Pd6Pt, the power density is lower in Nafion117 MEAs than in the nanocomposite. When used commercial Pt-carbon cloth (Pt-ETEK) for the electrodes, the power density achieved is 1.4 times higher for the Nafion117 MEAs than SPEEK nano-composites. The differences observed in performance is attributed to the large polarization losses found in the composite membranes because of the interfacial phenomena associated with the use of commercial Nafion-based electrodes., This research is in the frame of Support Programme for Research and Development of the Polytechnic University of Valencia, and the Ministry of Science and for funding provided through the projects: ENE2015-69203-R. OSF thanks to CONACYT-Mexico for supporting this research with the grant 475920.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A TRNSYS assisting tool for the estimation of ground thermal properties applied to TRT (thermal response test) data: B2G model

  • Cazorla-Marín, Antonio|||0000-0003-3314-0395
  • Montagud- Montalvá, Carla|||0000-0002-7118-6119
  • Montero Reguera, Álvaro Enrique|||0000-0002-4165-4743
  • Magraner, Teresa|||0000-0001-5292-1432
  • Corberán, José M.
[EN] The determination of ground thermal properties is essential to design competitive commercial ground source heat pump systems. A thermal response test (TRT) carried out on site allows the determination of both the conductivity of the ground and the borehole thermal resistance by means of analytical approaches, which require several simplifying assumptions as well as TRT durations of at least fifty hours and constant heat injection. In this context, a detailed dynamic numerical model of the borehole can help reducing both the uncertainties, associated with these simplifying assumptions, and the required test duration. This paper presents a TRNSYS tool to obtain the grout and ground thermal properties by means of a parameter estimation technique in conjunction with a two-dimensional dynamic numerical model, the B2G model, which is able to provide accurate results with a much shorter testing time and without the necessity of a constant heat injection. The methodology to estimate the borehole and ground characteristics has been validated thanks to the analysis of a set of experimental TRTs for U-pipe vertical boreholes carried out in different type of soils and borehole geometries. Results show that, for the analysed tests, it is possible to obtain an accurate and fast estimation of the ground thermal conductivity with reductions of the necessary TRT duration of up to a 70%, with a total uncertainty between +/- 10% and +/- 18%, considering not only the uncertainty introduced by the reduction of the test duration, but also the main sources of uncertainty.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Thermal response test analysis for U-pipe vertical borehole heat exchangers under groundwater flow conditions

  • Magraner, Teresa|||0000-0001-5292-1432
  • Montero Reguera, Álvaro Enrique|||0000-0002-4165-4743
  • Cazorla-Marín, Antonio|||0000-0003-3314-0395
  • Montagud- Montalvá, Carla|||0000-0002-7118-6119
  • Martos, Julio
[EN] Conventional models used in the analysis of thermal response test data only consider conduction as heat transfer mechanism. In cases where presence of groundwater is detected, convection heat transmission plays an important role, so its influence must be determined in the calculation of the effective thermal conductivity, usually overestimated in these situations, increasing its value the higher the power injected and the time elapsed. In this work, based on the data collected in a borehole located at UPV (Valencia) in which have been carried out three thermal response tests with different characteristics, has been implemented a variation of the finite line source model introducing an expression for the effective thermal conductivity formed by two terms, one static unaffected by underground flow and another dynamic that depends on time. Analyzing the data in the model developed and in the finite line source and infinite line source models, the results show that the new model estimates accurately the conductivity value unaffected by underground flow regardless the power injected or the time elapsed in the test, with differences between the results obtained in the analysed tests and average thermal conductivity of 1,4%, compared to the conventional models in which this difference is 27%., This work has been supported by the Spanish Government under project "Modelado, simulacion y validacion experimental de la transferencia de calor en el entorno de la edificacion" (ENE200800599/CON)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Ionic Liquid Composite Polybenzimidazol Membranes for High Temperature PEMFC Applications

  • Escorihuela, Jorge
  • Garcia-Bernabe, Abel|||0000-0002-9740-0830
  • Montero Reguera, Álvaro Enrique|||0000-0002-4165-4743
  • Sahuquillo, Oscar|||0000-0001-5360-3743
  • Giménez Torres, Enrique|||0000-0002-6330-0209
  • Compañ Moreno, Vicente|||0000-0001-8233-7472
[EN] A series of proton exchange membranes based on polybenzimidazole (PBI) were prepared using the low cost ionic liquids (ILs) derived from 1-butyl-3-methylimidazolium (BMIM) bearing different anions as conductive fillers in the polymeric matrix with the aim of enhancing the proton conductivity of PBI membranes. The composite membranes prepared by casting method (containing 5 wt. % of IL) exhibited good thermal, dimensional, mechanical, and oxidative stability for fuel cell applications. The effects of anion, temperature on the proton conductivity of phosphoric acid-doped membranes were systematically investigated by electrochemical impedance spectroscopy. The PBI composite membranes containing 1-butyl-3-methylimidazolium-derived ionic liquids exhibited high proton conductivity of 0.098 Scm(-1) at 120 degrees C when tetrafluoroborate anion was present in the polymeric matrix. This conductivity enhancement might be attributed to the formed hydrogen-bond networks between the IL molecules and the phosphoric acid molecules distributed along the polymeric matrix., The authors acknowledge the Spanish Ministerio de Economia y Competitividad (MINECO) for the financial support under the project ENE/2015-69203-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Analysis of initial stabilization of cell efficiency in amorphous silicon photovoltaic modules under real outdoor conditions

  • Mateo-Guerrero, Carlos
  • Hernández Fenollosa, María De Los Ángeles|||0000-0001-8003-3651
  • Montero Reguera, Álvaro Enrique|||0000-0002-4165-4743
  • Segui-Chilet, Salvador|||0000-0002-2927-6938
[EN] This contribution presents a field study in which the initial stabilization of thin-film amorphous silicon (a-Si:H) is investigated. Two grid-connected a-Si:H photovoltaic plants have been monitored and analyzed under real outdoor conditions. A per-unit approach is proposed to compare PV plants with differences in their electrical characteristic and the start-up date. The representation of a normalized per unit PV power versus the accumulated incoming irradiation reveals an evolution that can be characterized through an exposure-response function. By this function, two populations of defects in the cells are detected. It is found that the stabilization process in the first year of operation produces a decrease of 10% in the peak power, equivalent to a decrease of 0.5% in cell efficiency. The use of the accumulated PSH for conducting the analysis of the initial stabilization produces similarities that cannot be obtained if a time scale is used. These results provide a powerful tool for PV plant designers because they enable a prediction to be made of the time-scale stabilization response in terms of unitary power, correlated with the peak sun hours received. (C) 2017 Elsevier Ltd. All rights reserved., This work was supported by Generalitat Valenciana (PROM-ETEOII/2014/059) and Spanish MINECO (Ministry of Economy and Competitiveness TEC2014-53727-C2-1-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of seed layer thickness on properties of electrodeposited ZnO nanostructured films

  • Reyes Tolosa, María Dolores
  • Alajami, M.
  • Damonte, L.C.
  • Montero Reguera, Álvaro Enrique|||0000-0002-4165-4743
  • Hernández Fenollosa, María De Los Ángeles|||0000-0001-8003-3651
[EN] The quality and properties of electrodeposited nanostructured ZnO films are improved when they are deposited on a crystal lattice-matching substrate. To this end, a highly conductive indium tin oxide substrate is covered with an interlayer of ZnO using direct-current magnetron sputtering. In this manuscript, we describe the effect of this interlayer on the morphological and optical properties of several nanostructured ZnO films grown by different electrodeposition methods. The thickness of the ZnO interlayer was varied starting from ultrathin layers of 10 nm all the way up to 230 nm as determined by ellipsonnetry. The structural and optical properties of the nanostructured ZnO films deposited on top of these interlayers were characterized using field emission scanning electron microscopy (FESEM), atomic force microscopy and UV-visible spectroscopy. Optimum properties of the nanostructured ZnO films for application in thin-film optoelectronic devices are obtained when the ZnO interlayer has a thickness of approximately 45 nm. This is the case for all the electrodeposition methods used in this work.