Skip to main content

Diagnosis and Intervention on Cultural Heritage built with stone

IJCI-2017-32771

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de Promoción del Talento y su Empleabilidad en I+D+i
Subprogram Subprograma Estatal de Incorporación
Call Juan de la Cierva Incorporación
Call year 2017
State Plan 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre UNIVERSIDAD DE VIGO

Resultados relacionados

Resultados totales (Incluyendo duplicados): 13
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Identification of the best-performing novel microbial strains from naturally-aged graffiti for biocleaning research

  • Bosch-Roig, Pilar|||0000-0003-2019-399X
  • Pozo-Antonio, J.S.
  • Sanmartín, P.
[EN] Microorganisms that can act as biocleaning agents can potentially be isolated from existing graffiti. In this study, a total of 30 different isolates of bacteria, fungi and yeasts were obtained from black, blue, red and silver graffiti coatings exposed outdoors conditions for 10 years. An additional strain was obtained from samples of black powdered graffiti exposed under laboratory conditions for 5 years. Each of the isolates from the most prolific sources (i.e. red and silver graffiti coatings and black powdered graffiti) was evaluated alone and in combination with Tween? 20, to determine their potential as biocleaning agents, in test tube assays. Two strains isolated from the red graffiti coating (identified as Candida parapsilosis) and one strain isolated from the black powered graffiti (identified as Rhodococcus erythropolis) performed best alone. The quantity of live cells throughout the trials and biofilm formation indicated that both strains were able to utilize the paint as a substrate. When the microorganisms isolated were combined with Tween? 20, the quantity of live cells increased notably throughout the incubation time, and turbidity and graffiti discoloration were observed. Infrared spectroscopic examination revealed that R. erythropolis performed the best alone, while the addition of Tween? 20 to C. parapsilosis enhanced the oxidative degradation of the graffiti., J.S. Pozo-Antonio is grateful to the Spanish Ministry of Economy and Competitiveness (MINECO) for a post-doctoral contract (Juan de la Cierva-Incorporacion, IJCI-2017-3277). P. Sanmartin is grateful for financial support from the Xunta de Galicia (grant ED431C 2018/32).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Nanolime- and nanosilica-based consolidants applied on heated granite and limestone: Effectiveness and durability

  • Pozo-Antonio, J.S.
  • Otero, J.
  • Alonso, P.
  • Mas-Barberà, Xavier|||0000-0001-6654-624X
[EN] This paper shows a study on the consolidation effectiveness of nano-silica and nano-lime-based consolidants (i.e. Nano Estel (R) and Nanorestore (R), respectively), both available on the market, on two stones with different mineralogy and texture (i.e. two micas granite and Lioz limestone) previously subjected to 500 degrees C during 24 h with a rapid cooling by water jet simulating the real practice in a fire. The consolidation effectiveness was determined through the evaluation of hydro-physical properties (i.e. open porosity, apparent density, water absorption by capillarity and water absorption at atmospheric pressure), the determination of P-wave velocity (compressional wave velocity) and the study of their side-effects by using stereomicroscopy, colour spectrophotometry, Fourier transform infrared spectroscopy and scanning electron microscopy. Durability of the consolidants was determined by measuring their resistance to salt crystallization cycles and the subsequent surfaces were evaluated by open porosity measurements, stereomicroscopy, Fourier transform infrared spectroscopy and scanning electron microscopy. Results showed, as expected, that both granite and limestone samples increased their porosity after the heating process. In the case of granite stone, both products yielded similar reduction of the porosity and similar resistance to salt crystallization cycles. In case of limestone, nanolime samples yielded lower effectiveness in terms of dry matter, porosity, and water absorption by capillary coefficient, which is attributed to the low penetration of Nanorestore (R) particles in the fine pore structure of this stone. Ethyl silicate treated samples presented higher levels of decay after crystallization cycles in the limestone samples, which could be attributed to the difficulty to bond silicate materials to fine porous calcite-based substrates., J.S. Pozo-Antonio was supported by the Ministry of Economy and Competitiveness, Government of Spain through grant number IJCI-2017-32771
Investigo. Repositorio Institucional de la Universidade de Vigo
Publication Artículo científico (JournalArticle)

Cleaning of gypsum-rich black crusts on granite using a dual wavelength Q-Switched Nd: YAG laser

  • Pozo Antonio, José Santiago
  • Papanikolaou, Athanasia
  • Philippidis, Aggelos
  • Melessanaki, Kristalia
  • Rivas Brea, Maria Teresa
  • Pouli, Paraskevi
Gypsum black crust is one of the most severe deterioration forms affecting the built Cultural Heritage (CH) worldwide. Its removal from granitic substrates is necessary since gypsum layer favours the deterioration of the rock. This study investigates the laser assisted removal of gypsum black crust, from a Hercynian granite from the North-West (NW) Iberian Peninsula. The suggested laser cleaning methodology involves the combination of two wavelengths (1064 nm and 355 nm) from a QS Nd:YAG laser system and is based on their simultaneous interaction with the involved materials at various fluence values and FIR/FUV ratios (1/1, 1/3 and 3/1). This ablative scheme was initially introduced in order to overcome undesirable discoloration issues recorded upon single wavelength laser cleaning of black crusts but its role to effectively remove different undesired over-layers was also acknowledged. The results of this study were comparatively evaluated with surfaces irradiated using one of the two specific wavelengths, while the presence of water as an enhancing cleaning agent was also considered. A multi-analytical evaluation methodology based on stereomicroscopy, Raman spectroscopy, Fourier Transform Infrared spectroscopy (FTIR) and Scanning Electron Microscopy with Energy Dispersive X-ray Spectroscopy (SEM-EDS), was carried out to determine the optimum cleaning strategy in terms of crust removal effectiveness and minimisation of damages to the substrate. The optimum irradiation condition determined in this study is the simultaneous application of the two wavelengths in FIR/FUV = 1/1 ratio (with FIR = FUV = 0.3 J·cm−2) on a pre-wetted surface. Under this irradiation condition a high removal level of carbonaceous pollution particles and gypsum was achieved, without any damage to the granitic minerals in the form of melting and spallation and/or exfoliation of planes of biotite and K-feldspar and cleavage fracture of quartz., Xunta de Galicia, Universidade de Vigo, Ministerio de Ciencia, Innovación y Universidades | Ref. IJCI-2017-32771, Ministerio de Economía y Competitividad | Ref. BIA2014-54186-R
Investigo. Repositorio Institucional de la Universidade de Vigo
Publication Artículo científico (JournalArticle)

Aesthetic effects on granite of adding nanoparticle TiO2 to si-based consolidants (ethyl silicate or nano-sized silica)

  • Pozo Antonio, José Santiago
  • Noya, Daniel
  • Montojo Santos, Cristina
Considering that consolidant products are commonly used in the cultural heritage field and the titanium oxide nanoparticles (TiO2) have been used to develop photocatalyst films to induce self-cleaning property, the scientific research on consolidants doped with TiO2 is justified. However, the addition of TiO2 can affect to the physical properties of the cultural heritage object, questioning the adequacy of the procedure. In this paper, we evaluated the influence of nanoparticle TiO2 addition to two different commercial consolidant products (ethyl silicate or nano-sized silica) on the appearance and the color of a granite and the penetration through its fissure system. The stone was previously subjected to high temperature simulating the effect of a fire and the subsequent tap water jet to cool down. Therefore, different concentrations of nanocrystalline TiO2 (0.5, 1, and 3 wt %) were considered. The different compositions were also studied considering the compactness, the extent and the thickness of the superficial xerogel coating, and as well the penetration of the consolidant. The minimal TiO2 concentration tested (0.5 wt %) implied a low-medium risk of incompatibility as an intervention in cultural heritage field, because its low-medium potential as inducer of visible color changes of the granite surface. Regardless of the TiO2 content, the nano-sized silica induced surface xerogel coatings more compact and continue than those formed in the ethyl silicate coated surfaces. Higher penetration rates were identified in the granite treated with nano-sized silica colloidal solution, while ethyl silicate was only found in the first few µm. It was found that penetration could depend on the application procedure, the solvent of the consolidant and the silica particle size. The TiO2 addition reduced the penetration of the nano-sized silica consolidant., Ministerio de Economía y Competitividad | Ref. IJCI-2017-32771
Investigo. Repositorio Institucional de la Universidade de Vigo
Publication Artículo científico (JournalArticle)

Efficacy of mechanical procedures for removal of a lichen and a gypsum black crust from granite

  • Pozo Antonio, José Santiago
  • Alonso Villar, Enrique Manuel
  • Rivas Brea, Maria Teresa
Financiado para publicación en acceso aberto: Universidade de Vigo/CISUG, This paper provides preliminary data on the use of three different mechanical procedures to remove the lichen Diploschistes scruposus and a gypsum black crust from an ornamental granite. The methods used were wet sandblasting (Hydrogommage®), dry sandblasting (IBIX®) and dry-ice blasting. In addition, lichens were also removed by scraping with a scalpel. The cleaning efficacy and undesirable effects to granite were evaluated by stereomicroscopy, colour spectrophotometry, Fourier-transform infrared spectroscopy and scanning electron microscopy. The cleaning efficacy of the mechanical methods depended on the deposit being removed: i) for lichen, dry sandblasting and dry ice blasting produced the best results, while for the black gypsum crust, although both dry and wet sandblasting removed the black particulate matter from the crust, gypsum crystals remained on the surface; ii) the dry sandblasting method induced extraction of granite grains with the subsequent appearance of fissures; iii) for the lichen, the wet sandblasting method was totally unsatisfactory and iv) for the gypsum black crust, dry ice blasting failed to remove the black particulate matter from the crust., Ministerio de Economía, Industria y Competitividad | Ref. IJCI-2017-32771
Investigo. Repositorio Institucional de la Universidade de Vigo
Publication Artículo científico (JournalArticle)

Influence of the laser wavelength on harmful effects on granite due to biofilm removal

  • Barreiro Castro, Pablo
  • Andreotti, Alessia
  • Colombini, María Perla
  • González Fernández, Pío Manuel
  • Pozo Antonio, José Santiago
The colonization of stone-built monuments by different organisms (algae, fungi, lichens, bacteria, and cyanobacteria) can lead to biodeterioration of the stone, negatively affecting the artistic value of the heritage. To address this issue, laser cleaning has been widely investigated in recent years, due to the advantages it offers over traditional mechanical and chemical methods: it is gradual, selective, contactless, and environmentally friendly. That said, the laser parameters should be optimized in order to avoid any by-effects on the surface as a result of overcleaning. However, as the adjustment of each parameter to clean polymineralic stones is a difficult task, it would be useful to know the effect of overcleaning on the different forming minerals depending on the wavelength used. In this paper, three different wavelengths (355 nm, 532 nm, and 1064 nm) of a Q-Switch neodymium-doped yttrium aluminum garnet (Nd:Y3Al5O12) laser, commonly known as QS Nd:YAG laser were applied to extract a naturally developed sub-aerial biofilm from Vilachán granite, commonly used in monuments in the Northwest (NW)Iberian Peninsula. In addition to the removal rate of the biofilm, the by-effects induced for fluences higher than the damage threshold of the stone were evaluated using stereomicroscopy, color spectrophotometry, and scanning electron microscopy with energy-dispersive x-ray spectroscopy. The results showed that different removal rates were obtained depending on the wavelength used and 532 nm obtained the highest removal level. In terms of by-effects, biotite melting was registered on all surfaces regardless of the wavelength. In addition, 532 nm seemed to be the most aggressive laser system, inducing the greatest change in appearance as a result of extracting the kaolinite crackled coating and the segregations rich in Fe, which are a result of natural weathering. These changes were translated into colorimetric changes visible to the human eye. The surfaces treated with 355 nm and 1064 nm showed lower surface changes., Erasmus+ | Ref. HE Staff Mobility Program 2016, Ministerio de Economía y Competitividad | Ref. IJCI-2017-32771
Investigo. Repositorio Institucional de la Universidade de Vigo
Publication Artículo científico (JournalArticle)

Resistance to artificial daylight of paints used in urban artworks. Influence of paint composition and substrate

  • Alonso Villar, Enrique Manuel
  • Rivas Brea, Maria Teresa
  • Pozo Antonio, José Santiago
Financiado para publicación en acceso aberto: Universidade de Vigo/CISUG, Solar radiation is one of the deterioration factors par excellence of modern urban artworks, as among other manifestations, it causes loss of colour. This deterioration can compromise the durability of the works, although it is not known to what extent this durability can vary depending on the substrate supporting the paint. We evaluated the susceptibility to sunlight of 10 paints of differing compositions as typically used by urban artists, by exposing them, applied to concrete and brick, to artificial sunlight ageing test in laboratory conditions. Colour changes over time were studied, along with mineralogical (x-ray diffraction), chemical (scanning electron microscopy-energy dispersive x-ray spectroscopy) and physical (contact angle and peeling tests) changes. The durability of the paints on these substrates depends mainly on the paint composition (base, pigment and filler) but also on the type of substrate, as this influences paint adhesion capacity. The greatest colour modification was detected in fluorescent paints, which lose colour due to degradation of the organic phase, and with aggravation of defects during drying, eventually detach from the substrate., Ministerio de Economía y Competitividad | Ref. IJCI-2017-32771
Investigo. Repositorio Institucional de la Universidade de Vigo
Publication Artículo científico (JournalArticle)

Impact of wildfire on granite outcrops in archaeological sites surrounded by different types of vegetation

  • Pozo Antonio, José Santiago
  • Sanmartín Sánchez, Patricia
  • Serrano, Miguel
  • Rosa Arranz, José M. de la
  • Miller, Anna Z
  • Sanjurjo Sánchez, Jorge
The lack of scientific information about the effects of wildfire on prehistoric structures and rock art, such as dolmens and petroglyphs, impedes the development of conservation guidelines. In this study, the impact of a recent wildfire (late 2017) on granite outcrops in the San Salvador de Coruxo archaeological site (Vigo, SW Galicia) was evaluated. Samples of the same type of granite were obtained from three sites characterised by different types of vegetation (natural scrub, native deciduous oak and non-native pine-eucalypt forest) in order to determine how the vegetation influences the fire-caused damage to the rock. Three subsamples were taken from each of the granite samples at depths of 1 cm–3 cm to study how fire affects the rock at depth. In all sites, the temperature reached at the granite surface was below 380 °C. No mineralogical changes due to fire exposure were detected, and no physical changes that could be attributed to the effect of the fire on the fissure system of the granite were identified. However, aesthetic colour changes due to the deposition of organic and charred matter, which even penetrated the fissures, were detected. The existence of lignin-derived compounds, lipids and carbohydrates in the samples from the oakwood site indicates greater resistance to fire effects in this type of vegetation than in the other two types. Although preliminary, these findings suggest that oakwoods could act as protective belts around archaeological sites by reducing the wildfire severity, because of their greater resistance to being burnt, and that they could buffer the damaging effects of fire in natural areas where parietal art is found., Ministerio de Ciencia, Innovación y Universidades | Ref. IJCI-2017-32771, Ministerio de Economía y Competitividad | Ref. RYC2014-16338, Xunta de Galicia | Ref. ED431C 2018/32, Xunta de Galicia | Ref. ED431B 2018/36, Xunta de Galicia | Ref. ED431B 2018/47, Fundação para a Ciência e a Tecnologia | Ref. CEECIND/01147/2017
Investigo. Repositorio Institucional de la Universidade de Vigo
Publication Artículo científico (JournalArticle)

IR irradiation to remove a sub-aerial biofilm from granitic stones using two different laser systems: An Nd: YAG (1064 nm) and an Er:YAG (2940 nm)

  • Barreiro Castro, Pablo
  • González Fernández, Pío Manuel
  • Pozo Antonio, José Santiago
A sub-aerial biofilm (SAB) developed on a granite commonly found in the built cultural heritage of the NW Iberian Peninsula was extracted with 2 different IR irradiations using an Nd:YAG laser at 1064 nm and an Er:YAG laser at 2940 nm. The methodology was based on the application of only one scan in order to evaluate the effect of the laser cleaning operated by applying different consecutive laser scanning and the suitability of these lasers as quick tools. The aim of this comparative study was twofold. The first goal was to find the most satisfactory level of extraction by comparing the results obtained by the different laser sources (IR wavelengths). The other aim was to investigate the by-effects induced by both lasers on each granite-forming mineral. Evaluations were made using stereomicroscopy, Fourier transform infrared spectroscopy, Raman spectroscopy and scanning electron microscopy with energy-dispersive x-ray spectroscopy. The results were interpreted in terms of SAB extraction and damage induced on the granite. The results showed that the Nd:YAG laser achieved the most successful level of cleaning, because it extracted the most SAB, while causing the least amount of damage to the surfaces. Regardless of the fluence applied, the Er:YAG laser did not completely extract the SAB in only one scan; in addition, a more intense melting of biotite grains was found, producing amorphous fusion crusts and losing the distinction of the cleavage planes., Agencia Estatal de Investigación | Ref. IJCI-2017-32771
Investigo. Repositorio Institucional de la Universidade de Vigo
Publication Artículo científico (JournalArticle)

Nd:YAG and Er:YAG laser cleaning to remove Circinaria hoffmanniana (Lichenes, Ascomycota) from schist located in the Côa Valley Archaeological Park

  • Pozo Antonio, José Santiago
  • Barreiro Castro, Pablo
  • González Fernández, Pío Manuel
  • Paz Bermúdez, Maria Graciela
Lichens are part of the dominant colonizer crusts of rock-art on schist in the Côa Valley Archaeological Park (NE Portugal). Among the several species observed at the site, Circinaria hoffmanniana is one of the most extensive on the rock surfaces. Given the historic value of the park's open-air prehistoric rock-art, which has been designated UNESCO World Heritage, an effective, precise, selective and controllable cleaning method for the engravings is required, in order to extract the lichen while avoiding any grain extraction and/or physical changes in the surface. Based on these requirements, 2 different lasers commonly used in the conservation and restoration of cultural heritage were applied in one scan, with the aim of obtaining a satisfactory level of cleaning as quickly as possible. The 2 lasers were: a Q-switched Nd:YAG (pulse duration of 6 ns) and a free-running Er:YAG (pulse duration of 250 μs), working at IR radiation of 1064 nm and 2940 nm respectively. The cleaning was evaluated by assessing the extraction rate and the damage induced on the schist using a multianalytical methodology based on stereomicroscopy, colour measurements in CIELAB and CIELCH colour spaces, Fourier transform infrared spectroscopy, Raman spectroscopy and scanning electron microscopy. Further studies should be performed to evaluate the tertiary bioreceptivity of the treated surface., Agencia Estatal de Investigación | Ref. IJCI-2017-32771
Investigo. Repositorio Institucional de la Universidade de Vigo
Publication Artículo científico (JournalArticle)

Developing new cleaning strategies of cultural heritage stones: Are synergistic combinations of a low-toxic solvent ternary mixtures followed by laser the solution?

  • Ricci, Chiara
  • Gambino, Francesca
  • Nervo, Marco
  • Piccirillo, Anna
  • Scarcella, Arianna
  • Zenucchini, Francesca
  • Pozo Antonio, José Santiago
As the UN Agenda 2030 recognizes heritage protection in several goals, this research was focused on the improvement of the graffiti removal from stones. The cleaning of two graffiti paints with different composition (an alkyd- and an acrylic–based paints) from two stones (gneiss and travertine) was performed considering a synergistic approach based on the combination of a low-toxic solvent ternary mixture, followed by an Nd:YAG laser. The different concentrations of the low-toxic solvents were based on the triangular Teas graph, keeping similar Hansen solubility of the products commonly used in conservation of cultural heritage: methyl ethyl ketone (MEK) and n-butyl acetate. The n-butyl acetate was replaced by mixture A (51% ethyl alcohol/11% acetone/38% isooctane) and MEK by mixture B (7%/13%/80%). Regardless of the graffiti composition, the gneiss was satisfactorily cleaned with the mixture A, while for the travertine, the best results were achieved by the mixture B. Then, surfaces treated with the mixtures were irradiated with a QS Nd:YAG laser working at 532 nm. The cleaning evaluation was performed by stereomicroscopy, color spectrophotometry, roughness measurements, reflectance measurements, and scanning electron microscopy. As result, regardless on the stone and the graffiti paints, it was confirmed the enhancement of cleaning of the mixtures followed by the Nd:YAG laser. However, it is crucial to identify previously the concentrations of the chemical products that allow the best performance considering the graffiti-stone interaction, on the one hand, and the optimal laser’s parameters, on the other hand., Ministerio de Economía, Industria y Competitividad | Ref. IJCI-2017-32771, Compagnia di San Paolo (Italia)
RUC. Repositorio da Universidade da Coruña
Publication Artículo científico (JournalArticle)

Enhancement of graffiti removal from heritage stone by combining laser ablation and application of a solvent mixture

  • Ricci, Chiara
  • Gambino, Francesca
  • Nervo, Marco
  • Piccirillo, Anna
  • Scarcella, Arianna
  • Zenucchini, Francesca
  • Ramil, Alberto
  • Pozo Antonio, José Santiago
[Abstract] In this study, it was evaluated the combined cleaning treatment based on laser ablation followed by the application of chemical products for removing alkyd graffiti paint from two different types of stone. Three different laser treatments (operated in Q-switched, long Q-switched and free short running modes) were applied to the stone samples. The best two treatments were then followed up by application of a chemical product (a low toxic ternary solvent mixture). The Q-switched and the long Q-switched laser treatments in combination with the chemical agent were more effective than either of the laser treatments alone, leaving fewer paint remains, but with minimal damage to the stone., C. Ricci was supported by the “Degrado Urbano” project of Fondazione Centro Conservazione e Restauro “La Venaria Reale” (Turin, Italy), funded by the “Compagnia di San Paolo”. J.S. Pozo-Antonio was supported by the Ministry of Economy and Competitiveness, Government of Spain, through grant number IJCI-2017-32771. The authors thank A. De Stefanis (Fondazione Centro Conservazione e Restauro “La Venaria Reale”) for help with conducting the cleaning tests. This research was performed within the framework of the teaching innovation group ODS Cities and Citizenship of University of Vigo (Spain).
RUC. Repositorio da Universidade da Coruña
Publication Artículo científico (JournalArticle)

Influence of the weathering rate on the response of granite to nanosecond UV laser irradiation

  • Rivas Brea, Teresa
  • Pozo Antonio, José Santiago
  • Ramil, Alberto
  • López, Ana
[Abstract]: Laser ablation is an accepted cleaning technology for cultural heritage stonework. Optimized laser ablation may,however, have different side effects depending on the mineralogical composition of the stone. In the case of graniticrocks, observed side effects – colour changes, fracturing or/and mineral melting – have been attributed to laser parameter interactions with the patina to be cleaned from this complex rock with a grained texture and polymineral composition. We describe the influence of the weathering degree of a granite on its response to laser irradiation, confirming that the existence of secondary minerals in the rock influences the intensity and typology of side effects. Knowledge of this influence is of special relevance to the conservation of heritage builtwith Western European Variscan granites, which are already slightly weathered in quarry. Two specimens of the same Variscan granite taken from the same quarry but with different colours (suggesting different weathering rates)were subjected to nanosecond (ns)Nd:YVO4 laser irradiation,working at 355nm(UV irradiation) under different fluences. The specimens responded very differently to laser irradiation in terms of colour changes and resistance of the main minerals to laser radiation. The existence on one of the specimens of kaolinite deposits covering feldspar grains and Fe oxyhydroxides filling fissures seemed to be the reason for the different response to laser radiation. Our findings would suggest the need, during laser interventions, to take into account – in addition to texture and porosity – the degree of weathering of this particular kind of granite, widely used in the architectural and archaeological heritage of Western Europe, This work was supported by the Spanish research project BIA2014-54186-R. J.S. Pozo-Antonio's research was supported by the Ministry of Economy and Competitiveness-Government of Spain through grant IJCI-2017-32771. We thank Ailish Maher for revising the English in a version of this manuscript.