Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

Docta Complutense
Publication Artículo científico (JournalArticle)

The influence of the phosphorus content on the bioactivity of sol–gel glass ceramics

  • Padilla Mondéjar, Sussette
  • Román Zaragoza, Jesús
  • Carenas, A
  • Vallet Regí, María Dulce Nombre
The aim of this work was to study the influence of the phosphorus on the crystallization and bioactivity of glass-ceramics obtained from sol–gel glasses. For this purpose two sol–gel glasses with a similar composition but one of them containing P2O5 (70% SiO2; 30% CaO and 70% SiO2; 26% CaO; 4% P2O5, mol%) were prepared. Pieces of these glasses were treated at temperatures ranging between 700°C and 1400°C for 3 h. The obtained materials were characterized by XRD, FTIR, SEM-EDS and the biaxial flexural strength was determined in samples heated at 1100°C. In addition, an in vitro bioactivity study in simulated body fluid (SBF) was carried out. The results showed that phosphorus plays an important role in the crystallization of the glasses: it induced the crystallization of calcium phosphate phases, the stabilization of the wollastonite phase at high temperature as well as the crystallization of SiO2 phases at low temperatures. Moreover, the presence of phosphorus produced a heterogeneous distribution of defects in the pieces and, therefore, the flexural strength of samples containing this element decreased. Finally, glass-ceramics obtained from glasses containing phosphorus showed the fastest formation rate of the apatite layer when soaked in SBF.
Docta Complutense
Publication Artículo científico (JournalArticle)

Hydroxyapatite suspensions as precursors of pieces obtained by gelcasting method

  • Padilla Mondéjar, Sussette
  • Vallet Regí, María Dulce Nombre
  • R Garcı́a-Carrodeguas
The aim of this work was to prepare slurries of hydroxyapatite (OHAp) with a high content of solids, which is necessary for shaping pieces by the gelcasting method. For this purpose different studies were carried out using powders of OHAp calcined at temperatures ranging between 600 and 1200 °C and several dispersants. Surface area, porosity and chemical composition of OHAp powders played a fundamental role in the viscosity of slurries. The highest concentration of solid was obtained with OHAp calcined at 1200 °C. The best dispersant was selected in a first stage, by electrophoretic measurements and sedimentation studies and, finally, by rheological measurements. The concentration of dispersant which provides the minimum viscosity, depended on the calcination temperature of the OHAp. A great increased of viscosity took place for time of slurries preparation higher than 30 min. Milling of powder for 20 h was necessary to improve the rheological behaviour of the slurries. Finally, ceramic bodies were prepared from fluid slurries containing 60 vol.% of solids and the mechanical properties were evaluated.
Docta Complutense
Publication Artículo científico (JournalArticle)

Processing and mechanical properties of hydroxyapatite pieces obtained by the gelcasting method

  • Padilla Mondéjar, Sussette
  • Vallet Regí, María Dulce Nombre
  • Ginebra, María Pau
  • Gil, Javier
The aim of this work was to prepare hydroxyapatite (HA) pieces, by the gelcasting method, with appropriate mechanical properties for using as bone implants. The mechanical properties of the obtained pieces were evaluated. The influence of the solid content on the rheological behaviour of the slurries and, in turn, on the mechanical properties, was investigated. Pieces were prepared by using slurries containing 55 and 60 vol.% of an HA calcined at 1200 °C and 47 vol.% of HA calcined at 1100 °C. HA powders calcined at lower temperature than 1100 °C were not suitable for producing concentrated slurries. The raw and calcined HA were characterised by XRD, FTIR, X-ray fluorescence and elemental analysis. The pieces sintered at different temperatures and times were characterised by XRD, and the sintering treatment applied to the specimens for mechanical testing (1300 °C for 24 h) was selected taking into account the phases present after sintering. The mechanical properties of the green bodies were higher than obtained by other methods and the ones of the final pieces were comparable to those obtained by other techniques. The results indicated that slurries with a solid content higher than a limit value (for which limited contraction occurs) must be used and that the rheological properties of the slurries play an important role in the mechanical properties of the resulting pieces.