Skip to main content

PROYECCION TERMICA POR PLASMA ATMOSFERICO A PARTIR DE DISOLUCIONES Y SUSPENSIONES CONCENTRADAS DE NANOPARTICULAS

MAT2009-14144-C03-01

•
Funding agency name Ministerio de Ciencia e Innovación
Funding agency acronym MICINN
Program Programa Nacional de Proyectos de Investigación Fundamental
Subprogram Subprograma de Proyectos de Investigación Fundamental no Orientada
Call Proyectos I+D
Call year 2009
State Plan 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Management unit Subdirección General de Proyectos de Investigación
Beneficiary centre UNIVERSITAT JAUME I DE CASTELLO

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of the feedstock characteristics on the microstructure and properties of Al2O3 TiO2 plasma-sprayed coatings

  • Vicent, M.
  • Bannier, E.
  • Benavente Martínez, Rut|||0000-0002-4566-9475
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Molina, T.
  • Moreno, R.
  • Sánchez, E.
[EN] Atmospheric plasma spraying (APS) is an interesting technique to obtain nanostructured coatings due to its versatility, simplicity and relatively low cost. However, nanometric powders cannot be fed into the plume using conventional feeding systems, due to their low mass and poor flowability, and must be adequately reconstituted into sprayable micrometric agglomerates. In this work, Al2O3–13 wt.%TiO2 nanostructured and submicron-nanostructured powders were deposited using APS. The feedstocks were obtained by spray drying from two starting suspensions, prepared by mixing two commercial nanosuspensions of Al2O3 and TiO2, or by adding nanosized TiO2 and submicron-sized Al2O3 powders to water. The spray-dried granules were heat-treated to reduce their porosity and the resultant powders were fully characterized. Optimization of the deposition conditions enabled the reconstituted powders to be successfully deposited, yielding coatings that were well bonded to the substrate. The coating microstructure, characterized by SEM, was formed by semi-molten feedstock agglomerates surrounded by fully molten particles that act as a binder. Moreover, microhardness, adhesion, and tribological behavior were determined, and the impact of the granule characteristics on these properties was studied. It was found that changing the feedstock characteristics allowed controlling the coating quality and properties., This work has been supported by the Spanish Ministry of Science and Innovation (project MAT2009-14144-C03).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Correlation of thermal conductivity of suspension plasma sprayed yttria stabilized zirconia coatings with some microstructural effects

  • Carpio, Pablo
  • Blochet, Quentin
  • Pateyron, Bernard
  • Pawlowski, Lech
  • Sanchez, Enrique
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
Yttria-stabilized zirconia (3YSZ) coatings were successfully obtained by suspension plasma spraying. The coatings present generally two-zones-microstructure comprising nanostructured zones contributed by unmolten, partially sintered nanoparticles sintered surrounded by lamellar splats formed from molten and agglomerated in-flight fine solids. In addition, different types of cracks inside the coating microstructure were classified and quantified by image analysis such as e.g. inner microcracks and segmentation cracks associated with quenching process as well as horizontal interlamellar cracks. Thermophysical properties of sprayed coatings were tested with a thermal diffusivity set up basing onto light flash principle. Subsequently, the thermal conductivity was determined with the use of literature data of density and specific heat. The calculations showed very low thermal conductivities values. The values did not correlate with coatings porosity data. Consequently, the analysis of variance (ANOVA) test allowed evaluating the possible impact of the various types of cracks on thermal conductivity. By this analysis, a good correlation between vertical cracks, which include microcracks and segmentation cracks, and thermal conductivity was found. The findings also confirmed the increase of thermal conductivity associated with this type of cracks., This work has been supported by the Spanish Ministry of Science and Innovation (project MAT2009-14144-C03) and the Research Promotion Plan of the Universitat Jaume I, action 2.1 (ref. E-2011-05) and action 3.1 (ref. PREDOC/2009/10).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Microstructure and photocatalytic activity of suspension plasma sprayed TiO2 coatings on steel and glass substrates

  • Bannier, E.
  • Darut, G.
  • Sánchez, E.
  • Denoirjean, A.
  • Bordes, M.C.
  • Ageorges, H.
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • E. Rayón|||0000-0002-0653-2046
In this study, TiO 2 coatings were deposited by suspension plasma spraying (SPS) from a commercial TiO 2 nanoparticle suspension on two different substrates: a standard stainless steel and a Pyrex glass. Coatings were sprayed on both substrates with an F4-MB monocathode torch; a Triplex Pro tricathode torch was also used to spray coatings just on the stainless steel substrates. Spraying distance and cooling were varied.The anatase content in the coatings, determined by XRD, ranged from 32 to 72 wt% A significant amount of anatase to rutile transformation was found to occur during cooling. Examination of the microstructure revealed that the coating microstructure was bimodal, involving a non-molten region consisting mainly of anatase nanoparticle agglomerates and a molten region. The glass substrate coatings displayed a segregated phase distribution, particularly when the surface to be coated was cooled. Photocatalytic activity was determined by a methylene blue test.The experimental data fitted well to a first-order kinetic. All the coatings exhibited high photocatalytic activity in comparison with that of a commercial sol-gel coating. However, unlike much of the previous research, photocatalytic activity did not correlate with the anatase content determined by XRD. © 2011 Elsevier B.V., This work has been supported by the Spanish Ministry of Science and Education (MAT2009-14144-C03-01), by the Spanish Ministry of Science and Innovation (PID-600200-2009-5) and by the European Commission in the frame of the Interreg IV B Sudoe programme (Eliare: SOE1/P1/F169).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Nanoindentation study of the mechanical and damage behaviour of suspension plasma sprayed TiO2 coatings

  • E. Rayón|||0000-0002-0653-2046
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Bonache Bezares, Victoria
  • Bannier, E.
  • Sánchez, E.
  • Denoirjean, A.
  • Ageorges, H.
TiO2 coatings can be used as self-cleaning surfaces owing to their photocatalytic and hydrophilic properties. Suspension plasma spray (SPS) has proven to be a feasible and cheap technique for producing self-cleaning surfaces with acceptable photo-activity. This paper presents a nanoindentation study of the mechanical properties (hardness. Young's modulus and scratch resistance) of photoactive layers of suspension plasma sprayed TiO2 coatings applied on to glass substrates. Microstructure observation showed that the rutile grains were surrounded by fine anatase crystals. Under the same spraying conditions, the resulting anatase/rutile concentrations varied depending on the cooling rate (the substrate being either cooled with water or in air). The results showed that higher concentrations of anatase, which is softer than rutile, reduced the scratch damage and increased the friction coefficient. (C) 2011 Elsevier B.V. All rights reserved., The study was financially supported by the Spanish Ministry of Science and Innovation (PID-600200-2009-5 and MAT2009-14144-C03-01 -02).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Microstructure and indentation mechanical properties of YSZ nanostructured coatings obtained by suspension plasma spraying

  • Carpio, P.
  • Pawlowski, L.
  • Cattini, A.
  • Bannier, E.
  • Sánchez, E.
  • E. Rayón|||0000-0002-0653-2046
  • Benavente Martínez, Rut|||0000-0002-4566-9475
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
[EN] A commercial nanosuspension of yttria-stabilised zirconia (YSZ) was successfully deposited on austenitic stainless steel substrate by suspension plasma spraying technique (SPS). A SG-100 torch with internal radial injection was used for the spraying. The pneumatic system transported the feed suspension from the containers to the plasma torch. In order to study the effect of the spraying parameters, a factorial model was used to design the experiments, changing both spraying translation speed and suspension flow rate. The coating microstructure was characterised by FEG-SEM. All coatings displayed a two-zone microstructure formed by nanometre-sized particles surrounded by fully molten areas. Moreover, crystalline phases were determined by XRD and Raman spectroscopy. Mechanical properties were also determined using nanoindentation technique. Nanoindentation tests showed a bimodal distribution of the mechanical properties (hardness and Young's modulus) which is related to the two zones (molten and partially molten) present in the coatings. (C) 2012 Elsevier B.V. All rights reserved., This work has been supported by the Spanish Ministry of Science and Innovation (project MAT2009-14144-C03) and the Research Promotion Plan of the Universitat Jaume I, action 2.1 (ref. E-2011-05) and action 3.1 (ref. PREDOC/2009/10). The authors are grateful to Leszek Łatka for his help in plasma spray experiments.