Skip to main content

ESTUDIO DE PROPIEDADES FISICO-QUIMICAS DE INTERFASE BIOMATERIAL/SUERO FISIOLOGICO PARA DETERMINAR MECANISMOS DE DEGRADACION TRIBO-ELECTROQUIMICOS DE ALEACIONES BIOMEDICAS

MAT2011-22481

•
Funding agency name Ministerio de Ciencia e Innovación
Funding agency acronym MICINN
Program Programa Nacional de Proyectos de Investigación Fundamental
Subprogram Subprograma de Proyectos de Investigación Fundamental no Orientada
Call Proyectos I+D
Call year 2011
State Plan 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Management unit Subdirección General de Proyectos de Investigación
Beneficiary centre UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 9
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of the fabrication process and fluoride content on the tribocorrosion behaviour of Ti6Al4V biomedical alloy in artificial saliva

  • LICAUSI, MARIE-PIERRE
  • Igual Muñoz, Anna Neus
  • Amigó, Vicente|||0000-0002-2107-0273
Titanium and its alloys are widely used as dental implants due to their low density, excellent biocompatibility, mechanical properties and corrosion resistance. However, during their life time Ti6Al4V biomedical alloys are subjected to different mechanical actions (i.e.,sliding or fretting), thus resulting in a tribocorrosion system, which is an irreversible materia ldegradation process due to the combine deffect of corrosion and wear. In this study, the tribo-electrochemical behavior of cast and sintered (by powder metallurgy) Ti6Al4V alloy in artificial human saliva solution with out and with fluoride additions of 100 ppm and 1000 ppm and in an average industrial mouth wash solution with a 112 ppm fluoride content have been investigated by different electrochemical techniques. The same tribocorrosion mechanisms were found in the cast and sintered titanium alloys, although slightly different wear debris behavior was observed. At low applied passive potentials, wear rates are similar to those obtained under equilibrium conditions (Open Circuit Potential). There exists a critical fluoride concentration above which corrosion and tribocorrosion rates increase., We wish to express our gratitude to the Ministerio de Ciencia e Innovacion of the Spanish government for the financial support under the project MAT2011-22481 and to the Comunidad Valenciana for the grant GRISOLIAP/2010/038.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Wear of CoCrMo alloys used in metal-on-metal hip joints: A tribocorrosion appraisal

  • Mischler, Stefano
  • Igual Muñoz, Anna Neus
A good biocompatibility, excellent mechanical properties and high corrosion resistance characterize CoCrMo alloys. Therefore they are widely used for artificial joints in biomedical implants. However, the degradation of the implants during service life leads to the release into the body of toxic ions and wear particles. This continuous degradation is of concern for long-term stability of the implants. Published literature has highlighted the relevance of lubrication as well as metallurgical and contact mechanical factors on the degradation of CoCrMo implant alloys. Recent experimental investigations have proposed tribocorrosion, i.e., the interplay of mechanical wear and corrosion by the body fluids, as one of the crucial degradation mechanism of implants. Tribocorrosion is sub-discipline of tribology and corrosion that recently made significant progresses in mechanistic understanding and modelling. The present work aims at evaluating published results on the degradation of CoCrMo alloys using existing tribocorrosion concepts. Results show that wear accelerated corrosion due to mechanical removal of the passive film during sliding is a major contribution to the overall degradation. Further, a transition from low (10(-6) N/mm(3) m) to high (10(-4) N/mm(3) m) wear coefficients was found at a threshold electrode potential close to 0.2 V-SHE These findings clearly show that electrochemical phenomena play a key role on the tribological behaviour of biomedical CoCrMo alloy implants., A. Igual Munoz expresses her gratitude to the Ministerio de Ciencia e Innovacion of the Spanish government for the financial support under the project MAT2011-22481.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Tribocorrosion mechanisms of Ti6Al4V biomedical alloys in artificial saliva with different pHs

  • LICAUSI, MARIE-PIERRE
  • Igual Muñoz, Anna Neus
  • Amigó, Vicente|||0000-0002-2107-0273
Titanium and its alloys has been widely used for the design of dental implants because of its biocompatibility, mechanical properties and corrosion resistance. The powder-metallurgy process is a promising alternative to the casting fabrication process of titanium alloys for bone implants design as the porous structure mimics the natural bone structures, allowing the bone to grow into the pores which results in a better fixation of the artificial implant. However, under in vivo conditions the implants are subjected to tribocorrosion phenomenon, which consists in the degradation mechanisms due to the combined effect of wear and corrosion. The aim of this study is to evaluate the tribocorrosion behaviour of cast and sintered Ti6Al4V biomedical alloy for dental applications using the cast material as reference. Titanium samples were tested in artificial human saliva solution with three different pHs (3, 6, 9) and in an acidic saliva with 1000 ppm fluorides (AS-3-1000F−) by different electrochemical techniques (potentiodynamic curves, potentiostatic tests and tribo-electrochemical tests). Cast and sintered titanium alloys exhibit the same tribocorrosion mechanisms in AS independently of the pH which consists in plastic deformation with passive dissolution, but the addition of fluorides to the acidified solution changes the degradation mechanism towards active dissolution of the titanium alloys., We wish to express our gratitude to the Ministerio de Ciencia e Innovacion of the Spanish government for the financial support under the project MAT2011-22481.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Passivation of a CoCrMo PVD Alloy with Biomedical Composition under Simulated Physiological Conditions Studied by EQCM and XPS

  • Valero Vidal, Carlos
  • Igual Muñoz, Anna Neus
  • Olsson, C.O.A.
  • Mischler, Stefano
Kinetics of passive film growth on a CoCrMo biomedical alloy have been studied using the Electrochemical Quartz Crystal Microbalance technique (EQCM) in phosphate buffer solution at room temperature and 37◦C. CoCrMo layers were deposited on the quartz crystals by physical vapor deposition (PVD) reaching a dense and compact deposition film with fine-grain structure. EQCM measurements were performed under potentiodynamic and potentiostatic conditions (at applied passive and transpassive potentials). Furthermore, ex-situ X-ray Photoelectron Spectroscopy (XPS) analysis of the each tested sample was performed at the end of the electrochemical test. The use ofEQCMallows distinguishing between electrochemical oxidation, passive and transpassive dissolution and passive film growth. In the passive domain the passive film thickness stabilizes within 200 to 400 s after an initial fast growth. The increase in current at the onset of the transpassive domain does not affect the passive dissolution rate. Only at higher potential dissolution rate increases due to the dissolution of Cr(VI), Co(III) and Mo(VI) species. The observed constant mass loss rate at transpassive potentials indicates that the passive film at these potentials is cracked or porous. Increasing temperature accelerates themass loss through the oxide/electrolyte interface enhancing the passive and transpassive dissolution and increasing the thickness of the oxide film, We wish to express our gratitude to the Spanish Government, "Ministerio de Educacion" for the economic support and the post-graduate grant (Ref.AP2007-01243) and "Ministerio de Ciencia e Innovacion" for the financial support (Ref.MAT2011-22481), the assistance of N. Xanthopoulos with the XPS measurements and P. Mettraux with the PVD deposits and assistance with the scanning electron micrographs.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Electrochemical behavior of near-beta titanium biomedical alloys in phosphate buffer saline solution

  • Dalmau Borrás, Alba
  • Guiñón Pina, Virginia
  • Devesa Albeza, Francisco
  • Igual Muñoz, Anna Neus
  • Amigó, Vicente|||0000-0002-2107-0273
The electrochemical behavior of three different near-β titanium alloys (composed by Ti, Nb and Sn) obtained by powder metallurgy for biomedical applications has been investigated. Different electrochemical and microscopy techniques were used to study the influence of the chemical composition (Sn content) and the applied potential on themicrostructure and the corrosion mechanisms of those titaniumalloys. The addition of Sn below4wt.% to the titanium powder improves the microstructural homogeneity and generates an alloy with high corrosion resistancewith lowelasticmodulus, beingmore suitable as a biomaterial.When the Sn content is above 4%, the corrosion resistance considerably decreases by increasing the passive dissolution rate; this effect is enhanced with the applied potential., The authors would like to thank the Ministerio de Ciencia e Innovacion of the Spanish Government for the financial support under the project MAT2011-22481.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Tribocorrosion behavior of beta titanium biomedical alloys in phosphate buffer saline solution

  • Guiñón Pina, Virginia
  • Dalmau, Alba
  • Devesa, F.
  • Igual Muñoz, Anna Neus
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] The tribo-electrochemical behavior of different β titanium alloys for biomedical applications sintered by powder metallurgy has been investigated. Different mechanical, electrochemical and optical techniques were used to study the influence of the chemical composition, Sn content, and the electrochemical conditions on the tribocorrosion behavior of those alloys Ti30NbxSn alloys (where x is the weight percentage of Sn content, 2% and 4%). Sn content increases the active and passive dissolution rate of the titanium alloys, thus increasing the mechanically activated corrosion under tribocorrosion conditions. It also increases the mechanical wear of the alloy. Prevailing electrochemical conditions between 1 and 2 V influences the wear accelerated corrosion by increasing it with the applied potential and slightly increases the mechanical wear of Ti30Nb4Sn. Wear accelerated corrosion can be predicted by existing models as a function of electrochemical and mechanical parameters of the titanium alloys., The authors would like to thank the Ministerio de Ciencia e Innovacion of the Spanish government for the financial support under the project MAT2011-22481.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Adsorption of BSA on Passivated CoCrMo PVD Alloy: An EQCM and XPS Investigation

  • Valero Vidal, Carlos
  • Igual Muñoz, Anna Neus
  • Olsson, Claes
  • Mischler, Stefano
[EN] Adsorption of Bovine Serum Albumin (BSA) on an anodically passivated CoCrMo biomedical alloy has been studied using the Electrochemical Quartz Crystal Microbalance (EQCM) in phosphate buffer solution at 37 degrees C. CoCrMo layers were deposited on the quartz crystals by physical vapor deposition. EQCM measurements were performed under potentiostatic conditions and combined with X-ray Photoelectron Spectroscopy (XPS) analysis. Adsorption of BSA onto the CoCrMo alloy surface was found to favor passive dissolution without modification of the chemical composition and thickness of the oxide passive film. In addition, passive film growth and adsorption kinetics of the protein follow a logarithmic trend. Both EQCM and XPS techniques demonstrated that protein coverage depends on the applied potential. (C) 2014 The Electrochemical Society. All rights reserved., We express our gratitude to the Spanish Government, "Ministerio de Economia y Competitividad" for the economic support (project reference MAT2011-22481) and the post-graduate grant (Ref.AP2007-01243), the assistance of N. Xanthopoulos with the XPS measurements and P. Mettraux with the PVD deposits.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of fabrication process on electrochemical and surface properties of Ti-6Al-4V alloy for medical applications

  • Dalmau Borrás, Alba
  • Guiñón Pina, Virginia
  • Devesa Albeza, Francisco
  • Igual Muñoz, Anna Neus
  • Amigó, Vicente|||0000-0002-2107-0273
The electrochemical behavior of rolled and sintered Ti-6Al-4V alloy has been investigated by different electrochemical techniques in order to study the influence of the fabrication process on the corrosion mechanisms of those titanium alloys. Before performing the electrochemical tests, an activation of the electrode surface is carried out to minimize the effect of the spontaneous formation of titanium oxides and to quantify the electrochemical active area of the alloys. The results show that the rolled and the sintered alloy have similar electrochemical behavior, but the sintered alloy presents higher corrosion resistance than the rolled one. Roughness factor associated to the powder metallurgy fabrication process is determined by Electrochemical Impedance Spectroscopy (EIS) and an active area 1.54 times higher than the rolled Ti-6Al-4V is obtained. The higher active area of the sintered alloys generate higher amount of metallic cations but also lower passive dissolution through the oxide film, then enhancing the passive film formation. Powder metallurgy is a promising fabrication technique to obtaining titanium biomedical alloys according to the optimal corrosion resistance. (c) 2013 Elsevier Ltd. All rights reserved, The authors would like to thank the Ministerio de Ciencia e Innovacion of the Spanish Government for the financial support under the project MAT2011-22481. They would also like to thank the Universidad Politecnica de Valencia for the specialization grant.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of carbides and microstructure of CoCrMo alloys on their metallic dissolution resistance

  • Valero Vidal, Carlos
  • Casaban Julián, Leandro
  • Igual Muñoz, Anna Neus
  • Herraiz Cardona, Isaac|||0000-0001-5829-6594
CoCrMo alloys are passive and biocompatible materials widely used as joint replacements due to their good mechanical properties and corrosion resistance. Electrochemical behaviour of thermal treated CoCrMo alloys with different carbon content in their bulk alloy composition has been analysed. Both the amount of carbides in the CoCrMo alloys and the chemical composition of the simulated body fluid affect the electrochemical properties of these biomedical alloys, thus passive dissolution rate was influenced by the mentioned parameters. Lower percentage of carbon in the chemical composition of the bulk alloy and thermal treatments favour the homogenization of the surface (less amount of carbides), thus increasing the availability of Cr to form the oxide film and improving the corrosion resistance of the alloy., We wish to express our gratitude to the Spanish Government, "Ministerio de Economia y Competitividad" MAT2011-22481 for the economic support.