Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 61
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

The effect of environmental conditions on the mechanical and thermoelectric properties of Bi2Ca2Co1.7Ox textured rods

  • Kahraman, F.
  • Diez, J. C.
  • Rasekh, Sh.
  • Madre, M. A.
  • Torres, M. A.
  • Sotelo, Andres
The effect of environmental conditions on the microstructural, mechanical and thermoelectric properties of highly textured Bi2Ca2Co1.7Ox thermoelectric materials was investigated by powder X-ray diffraction, scanning electron microscopy, three point bending test, electrical resistivity, and thermopower measurements. Textured thin rods were directionally grown from the melt through a laser floating zone melting technique. The mechanical and thermoelectric properties of Bi2Ca2Co1.7Ox were determined as a function of two different environmental conditions, air and water. Flexural strength data showed that these oxide materials possess an unsuspected degradation resistance. These good results have been related to the presence of a very thin (~250 µm) low porosity region and relatively small grain sizes, which avoids the internal degradation by water infiltration through the porosity. Moreover, thermoelectric performances, evaluated through the power factor are maintained practically unchanged, independently of the environmental conditions., The authors acknowledge financial support from the Gobierno de Aragón and the Fondo Social Europeo (Consolidated Research Groups T12 and T87) and MINECO-FEDER (Project MAT2013-46505-C3-1-R). F. Kahraman acknowledges a financial grant from the Council of Higher Education (YÖK) in Turkey for international mobility. Authors would like to acknowledge the use of Servicio General de Apoyo a la Investigación-SAI, Universidad de Zaragoza., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Use of laser technology to produce high thermoelectric performances in Bi2Sr2Co1.8Ox

  • Rasekh, Sh.
  • Costa, F. M.
  • Ferreira, Nuno M.
  • Torres, M. A.
  • Madre, M. A.
  • Diez, J. C.
  • Sotelo, Andres
Bi2Sr2Co1.8Ox bulk polycrystalline ceramics were prepared by conventional sintering of powders, obtained by polymer solution method and by directional growth using the laser floating zone technique. Microstructural analysis showed randomly oriented grains in the classical sintered materials, while in the laser-textured samples well oriented crystals with the c-axis nearly perpendicular to the growth direction were observed. A significant reduction on electrical resistivity, compared with the sintered materials, was observed due to the decrease on the secondary phases content. As a consequence, a raise on the power factor of about 2 and 5 times, compared with the classically sintered samples, was obtained for the as-grown and annealed laser-textured samples, respectively. The maximum power factor obtained at 650 °C in the annealed laser-textured samples (∼0.20 mW/K2 m) is much higher than the best value obtained in sinter–forged textured materials at the same temperature., The authors wish to thank the MINECO-FEDER (Project MAT2013--46505-C3-1-R) and the Gobierno de Aragón and Fondo Social Europeo (Research Groups T12 and T87) for financial support. F.M. Costa and N.M. Ferreira gratefully acknowledge the support from UID/CTM/50025/2013 project., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Very large superconducting currents induced by growth tailoring

  • Costa, F. M.
  • Ferreira, Nuno M.
  • Rasekh, Sh.
  • Torres, M. A.
  • Madre, M. A.
  • Diez, J. C.
  • Sotelo, Andres
The efforts of carrying forward superconducting materials to commercialization can be overcome by materials with high performance potentiated by a suitable processing technique. In this work, extreme critical currents up to 241 A @ 77 K were attained by tuning the crystal growth in a directional solidification process. Bulk rods of textured Bi-2212/2.9 wt % Ag were obtained by changing the conventional laser floating zone technique through the application of a d.c. electrical current during the crystallization process. Using an optimized composition, the electrically assisted laser floating zone (EALFZ) allowed obtaining 5800 A/cm2 in rods exhibiting only 2.3 mm in diameter, the highest value reported so far for bulk samples. This behavior is a consequence of the texture enhancement and radial phase distribution, exceeding a 2-fold increase in Jc compared with samples grown without electrical current. Morphological and structural observations are discussed and correlated with the results from the electrical characterization. Applications on extremely efficient electrical current leads working at temperatures below 77 K using the above-described materials grown by EALFZ are anticipated., The authors wish to thank the MINECO-FEDER (Project MAT2013-46505-C3-1-R) and Gobierno de Aragón and Fondo Social Europeo (Research Groups T12 and T87) for financial support. M. A. Madre acknowledges the MINECO-FEDER (Project MAT2011-22719) for funding. The authors acknowledge the financial support from the Portuguese Science and Technology Foundation (FCT) through the program UID/CTM/50025/2013., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Mechanical and thermoelectric environmental evolution properties of Bi2 Sr2 Co1.8 Ox ceramics textured by laser floating zone technique

  • Kahraman, F.
  • Sotelo, Andres
  • Madre, M. A.
  • Rasekh, Sh.
  • Torres, M. A.
  • Diez, J. C.
Bi2Sr2Co1.8Ox ceramics have been synthesized through solid-state reaction methods and directionally grown from the melt by laser floating zone technique. Mechanical and thermoelectric characteristics of this material were determined by three point bending tests and the four probe technique, respectively. The mechanical and thermoelectric properties of Bi2Sr2Co1.8Ox were determined as a function of the environmental conditions, air and water. Flexural strength data show that textured materials possess a high degradation resistance due to the low porosity of the external part of the rods (~65 µm), which avoids water infiltration and, as a consequence, the internal degradation. Moreover, power factor values are maintained practically unchanged for the samples immersed in water for 24 h., The authors acknowledge financial support from the Gobierno de Aragón and the Fondo Social Europeo (Consolidated Research Groups T12 and T87) and MINECO-FEDER (Project MAT2013-46505-C3-1-R). F. Kahraman acknowledges a financial grant from the Council of Higher Education (YÖK) in Turkey for international mobility., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effect of synthesis methods on the Ca3Co4O9 thermoelectric ceramic performances

  • Sotelo, Andres
  • Rasekh, Sh.
  • Torres, M. A.
  • Bosque, P.
  • Madre, M. A.
  • Diez, J. C.
Three different synthesis methods producing nanometric grain sizes, coprecipitation with ammonium carbonate, oxalic acid, and by attrition milling have been studied to produce Ca3Co4O9 ceramics and compared with the classical solid state route. These three processes have produced high reactive precursors and all the organic material and CaCO3·have been decomposed in a single thermal treatment. Coprecipitation leads to pure Ca3Co4O9 phase, while attrition milling and classical solid state produce small amounts of Ca3Co2O6 secondary phase. Power factor values are similar for all three samples, being slightly lower for the ones produced by attrition milling. These values are much higher than the obtained in samples prepared by the classical solid state method, used as reference. The maximum power factor values determined at 800 °C (~0.43 mW/K2 m) are slightly higher than the best reported values obtained in textured ones which also show much higher density values., The authors wish to thank the Gobierno de Aragón (Grupos de Investigacion Consolidados T12 and T87) and MINECO-FEDER (MAT2013-46505-C3-1-R) for financial support. Authors would like to acknowledge the use of Servicio General de Apoyo a la Investigación-SAI, Universidad de Zaragoza. Sh. Rasekh acknowledges a JAEPreDoc2010 grant from the CSIC., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Decrease of Ca3Co4O9+δ thermal conductivity by Yb-doping

  • Klirat, G.
  • Aksan, M. A.
  • Rasekh, Sh.
  • Madre, M. A.
  • Diez, J. C.
  • Sotelo, Andres
In this study, the effect of Yb-substitution on the structural, electrical and thermal transport properties of the CaCoO system has been investigated in the low temperature region (between 10 and 300 K). The resistivity of samples increases with raising the Yb-concentration in the system. All the samples show a metal-semiconductor transition below 85 K. In the analysis based on Strongly Correlated Fermi Liquid Model, an increased bandwidth and a reduced electronic correlation are found. It has also been found that the energy gap, E , value also decreases with Yb-substitution. The samples show positive thermoelectric power, indicating that dominant charge carriers are holes in all the samples. The thermoelectric power value decreases with Yb-substitution. From Mott equation, it is determined that the Fermi energy and hole concentration decrease in the Yb-susbtituted samples, compared to the undoped ones. Thermal conductivity, κ, is decreased in about 50% of the measured in undoped samples for the 0.01 and 0.03 Yb-doped samples at 300 K. Highest figure of merit, ZT, value is found to be 5.4 10 at 300 K for the unsubstituted sample and the ZT value decreases by the substitution., The authors wish to thank the MINECO-FEDER (Project MAT2013-46505-C3-1-R) and the Gobierno de Aragón and Fondo Social Europeo (Research Groups T12 and T87) for financial support., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effect of secondary annealing process on critical current density in highly textured Bi-2212 superconducting system

  • Aksan, M. A.
  • Madre, M. A.
  • Rasekh, Sh.
  • Constantinescu, G.
  • Torres, M. A.
  • Diez, J. C.
  • Sotelo, Andres
  • Yakinci, M. E.
Bi-2212 samples prepared by a solid-state reaction technique have been grown from the melt using the laser floating zone method. After annealing the as-grown bars, the samples showed a good grain alignment and a high transport critical current density. Secondary annealing processes were performed on the annealed samples with the aim of producing Bi-2212 phase controlled decomposition. Hence, the Bi-2201 phase and the secondary phases, which act as effective pinning centers, were obtained with the secondary annealing process. After these thermal treatments, the transport critical current densities of samples significantly increased, when compared to the annealed ones. The maximum critical current density was achieved when the samples were subjected to secondary annealing at 680°C for 168 h with an improvement of ~80%, compared to the annealed ones. Moreover, it was found that magnetization of the secondarily annealed samples was also increased. The magnetic critical current densities in these secondary annealed samples were about 3 times higher than the values obtained for the annealed ones. These results clearly indicate that the secondary annealing processes lead to the formation of effective pinning centers in the bulk material., The authors acknowledge financial support from the Gobierno de Aragón (Grupos de Investigacion Consolidados T12 and T87) and the Spanish MINECO-FEDER (Project MAT2013-46505-C3-1-R)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effect of Na doping on the Ca3Co4O9 thermoelectric performance

  • Constantinescu, G.
  • Rasekh, Sh.
  • Torres, M. A.
  • Bosque, P.
  • Diez, J. C.
  • Madre, M. A.
  • Sotelo, Andres
Ca3-xNaxCo4O9 polycrystalline thermoelectric ceramics with small amounts of Na (x=0, 0.01, 0.03, 0.05, 0.07, and 0.10) have been prepared using the classical solid state method. Microstructural characterization has shown that Na has been incorporated into the Ca3Co4O9 phase and that no Na-based secondary phases have been produced. It has also been found that Na addition promotes grain growth and favours sintering due to the formation of a small amount of liquid phase. Electrical resistivity decreases when Na content increases until 0.07Na addition while Seebeck coefficient is maintained practically unchanged. The improvement in electrical resistivity leads to higher power factor values than the usually obtained in samples prepared by more complex and expensive techniques., This research has been supported by the Spanish MINECO-FEDER (MAT2013-46505-C3-1-R). The authors wish to thank the Gobierno de Aragón-Fondo Social Europeo (Consolidate research group T12 and consolidated research group T87) for financial support., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effect of Yb substitution in Bi-2212 ceramics prepared by laser floating zone technique

  • Özkurt, B.
  • Özçelik, Bekir
  • Madre, M. A.
  • Sotelo, Andres
  • Diez, J. C.
In the present work, the influence of Yb substitution for Bi on the structural, electrical and magnetic properties of textured Bi-2212 ceramics has been investigated. X-ray diffraction studies indicated that the major peaks correspond to the Bi-2212 phase. The SEM images clearly show that there is an increase in the number of secondary phases with raising Yb content while all samples maintain similar grain morphology. Magnetic analysis of all samples has been done by magnetic hysteresis measurements, indicating that an enhancement in the M-H loops is obtained by a low Yb doping. The critical current density of samples was calculated from the M-H curves by using Bean’s critical state model, indicating that sample with 0.05 Yb substitution possesses the highest Jc values., The authors wish to thank the Gobierno de Aragón and Fondo Social Europeo (Grupos de Investigacion Consolidados T12 and T87) and MINECO-FEDER (MAT2013-46505-C3-1-R) for financial support., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Enhancement of mechanical and thermoelectric properties of Ca3Co4O9 by Ag addition

  • Kahraman, F.
  • Madre, M. A.
  • Rasekh, Sh.
  • Salvador, C.
  • Bosque, P.
  • Torres, M. A.
  • Diez, J. C.
  • Sotelo, Andres
Ca3Co4O9 + x wt.% Ag (x = 0, 1, 3, 5, and 10) polycrystalline thermoelectric ceramics have been prepared by a sol–gel route via nitrates followed by high temperature treatment before sintering. Out-of-plane XRD data have shown that major phase is the Ca3Co4O9 one, accompanied by metallic Ag. SEM observations have agreed with the XRD data. Apparent density measurements have revealed that all samples possess densities ranging between 80% and 90% when Ag content is raised. Mechanical properties have shown a drastic increase of bending stress when Ag is added to the samples. Electrical resistivity decreases with the Ag content, compared with the pure ones, while Seebeck coefficient slightly decreases. Maximum power factor values around 0.43 mW/K2 m at 800 °C have been achieved for the 10 wt.% Ag samples which is much higher than the measured in the pure Ca3Co4O9 samples., This research has been supported by MINECO-FEDER (MAT2013-46505-C3-1-R). The authors wish to thank the Gobierno de Aragón-Fondo Social Europeo (Consolidated Research Groups T12 and T87) for financial support., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Improvement of thermoelectric properties in Ca3Co4O9 ceramics by Ba doping

  • Constantinescu, G.
  • Rasekh, Sh.
  • Torres, M. A.
  • Madre, M. A.
  • Sotelo, Andres
  • Diez, J. C.
Ca3−xBaxCo4O9 bulk polycrystalline thermoelectric ceramics with x = 0.00, 0.01, 0.03 and 0.05 have been prepared through a classical solid state method. Microstructural characterizations of sintered samples have shown that Ba has been incorporated into the Ca3Co4O9 and/or Ca3Co2O6 structures and that no Ba-based secondary phases have been produced. The apparent density values increase when the amount of barium is raised with respect to the undoped samples, reaching a maximum value of around 77 % of the Ca3Co4O9 theoretical density, for samples with the highest amount of barium. Electrical resistivity of doped samples decreases in the whole measured temperature range with respect to the undoped ones, while Seebeck coefficient remains practically unchanged. In conclusion, the improvement in resistivity leads to power factor values which are higher than the ones measured in undoped samples, fact which makes this bulk polycrystalline compound a promising candidate for high-temperature power generation applications in oxidative environments., The authors wish to thank the MINECO-FEDER (project MAT2013-46505-C3-1-R) and the Gobierno de Aragón (Research Groups T12 and T87) for financial support., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Thermal conductivity and thermoelectric power of potassium and sodium-substituted Bi-2212 superconductor prepared by PEI technique

  • Özçelik, Bekir
  • Tangüner, A.
  • Gürsul, Mehmet
  • Sotelo, Andres
  • Madre, M. A.
In the present study, thermal conductivity (κ − T), thermoelectric power (S − T), and figure of merit (ZT) measurements from room temperature down to 20 K of polycrystalline Bi2Sr2Ca1−xNaxCu2O8+y and Bi2Sr2Ca1−xKxCu2O8+y superconductors prepared by a polymer solution technique using polyethyleneimine, PEI, have been carried out. The thermoelectric power, S(T), of samples have both negative (at high T) and positive values (at low T), and are found to increase with decreasing temperature, reaching their maximum values (peaks) around their Tc values and dropping rapidly to zero below Tc. Na and K substitutions also have a considerable effect on the thermal conductivity, κ. Namely, with increasing Na concentration the magnitude of κ is decreased, but for the K substitution, the magnitude of κ is drastically increased for x = 0.75., This work is supported by the Research Fund of Çukurova University, Adana, Turkey, under Grant Contract Nos FBE.2013YL45 and FEF2013BAP22. A. Sotelo and M. A. Madre wish to thank the Gobierno de Aragon and the Fondo Social Europeo (Research Group T12) and MINECO-FEDER (Project MAT2013-46505-C3-1-R) for the financial support., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Thermoelectric doping effect in Ca3Co4-xNixO9 ceramics, Efecto del dopaje en la propiedades termoeléctricas de cerámicas Ca3Co4-xNixO9

  • Constantinescu, G.
  • Rasekh, Sh.
  • Torres, M. A.
  • Bosque, P.
  • Madre, M. A.
  • Sotelo, Andres
  • Diez, J. C.
[EN]: Ca3Co4-xNixO9 (x=0.01, 0.03, and 0.05) polycrystalline thermoelectric ceramics have been prepared by the classical solid state method. As a result of the Ni addition an increase in porosity has been detected. Moreover, the presence of Ni has been related with the increase of Ca2Co3O6 secondary phase and the appearance of a new NiO-CoO solid solution. However, for the 0.01-Ni doped samples an improvement in the thermoelectric performances has been measured. This effect has been related with a decrease in the resistivity values and an increase in the Seebeck coefficient. The raise in the power factor for the 0.01-Ni doped samples, compared with the undoped ones, is between 10 and 25% at 50 and 800 ºC respectively. Moreover, the maximum power at 800 ºC, around 0.25 mW/K2.m, is significantly higher than the best results obtained in Ni doped samples reported previously in the literature., [ES]: Se han preparado muestras policristalinas de Ca3Co4-xNixO9 (x = 0,01, 0,03 y 0,05) mediante reacción en estado sólido. Se ha detectado un incremento de la porosidad en las muestras dopadas con Ni. La adición de Ni también ha provocado el aumento de la fase secundaria Ca2Co3O6, así como la aparición de una nueva fase consistente en una solución sólida de NiO-CoO. A pesar de ello se ha detectado una mejora de las prestaciones termoeléctricas en las muestras con un 0,01 de Ni. Esta mejora ha sido provocada por una disminución de la resistividad eléctrica y un aumento del coeficiente Seebeck., The authors wish to thank the Gobierno de Aragón and the Fondo Social Europeo (Research Groups T12 and T87) and MINECO-FEDER (Project MAT2013-46505-C3-1-R) for financial support., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Thermoelectric properties in Ca3Co4-xMnxOy ceramics

  • Constantinescu, G.
  • Torres, M. A.
  • Rasekh, Sh.
  • Bosque, P.
  • Madre, M. A.
  • Diez, J. C.
Ca3Co4-xMnxOy polycrystalline thermoelectric ceramics with small amounts of Mn have been prepared by the classical solid state method. X-ray diffraction data have shown that Ca3Co4O9 is the major phase, with small amounts of the Ca3Co2O6 one. Moreover, they show that the Mn has been incorporated into these two phases. Electrical resistivity decreases, compared with the values for undoped samples, with Mn content until a minimum for the 0·03 doped ones, increasing for higher Mn substitution. Seebeck coefficient does not change in all the measured temperature range, independently of Mn content. The improvement in electrical resistivity leads ∼30% higher power factor values for the 0·03 Mn doped samples than that obtained in the undoped ones. The maximum power factor at 800°C, ∼0·28 mW K-2 m-1, is close to that obtained in much higher density samples, clearly indicating the good thermoelectric properties of these samples., The authors wish to thank the Gobierno de Aragón (Research Groups T12 and T87) and the MINECO-FEDER (MAT2013-46505-C3-1-R) for financial support. Authors would also like to acknowledge the use of Servicio General de Apoyo a la Investigación-SAI, Universidad de Zaragoza. The technical contributions of C. Estepa and C. Gallego are also acknowledged. Sh. Rasekh acknowledges a JAE-PreDoc 2010 grant from CSIC., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Role of Ag in textured-annealed Bi2Ca2Co1.7Ox thermoelectric ceramic

  • Flahaut, D.
  • Allouche, J.
  • Sotelo, Andres
  • Rasekh, Sh.
  • Torres, M. A.
  • Madre, M. A.
  • Diez, J. C.
Bi2Ca2Co1.7Ox thermoelectric ceramics with small Ag additions (0, 1, 2, 3, 4, and 5 wt.%) have been successfully grown from the melt, using the laser floating zone method and subsequently annealed at 800 °C for 24 h. The microstructure has shown a reduction of the amount of secondary phases for Ag contents up to 4 wt.%. This microstructural evolution leads to a decrease of the electrical resistivity values until an Ag content of 4 wt.%, whereas Seebeck coefficient has been maintained unchanged. This is in agreement with the presence of metallic Ag in all samples, confirmed not only by Energy Dispersive Spectrometry but also by X-ray photoelectron and Auger spectroscopy. These electrical properties lead to maximum power factor values of about 0.30 mW/K2.m at 650 °C for the 4 wt.% Ag containing samples, which is among the best results obtained for this type of materials., This research has been supported by the Spanish MINECO-FEDER (MAT2013-46505-C3-1-R). The authors wish to thank the Gobierno de Aragón-FEDER (Consolidated Research Groups T87 and T12) for financial support., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Tailoring Ca3Co4O9 microstructure and performances using a transient liquid phase sintering additive

  • Sotelo, Andres
  • Costa, F. M.
  • Ferreira, Nuno M.
  • Amaral, Vitor S.
  • Amaral, J.S.
  • Rasekh, Sh.
  • Torres, M. A.
  • Madre, M. A.
  • Diez, J. C.
et al., A flexible, adaptable, economical and easily scalable processing route, allowing microstructural control, is presented. It involves classical solid state sintering method and addition of liquid promoting compound. Controlled porosity and high thermoelectric performance have been attained in CaCoO by KCO additions, drastically improving the sintering procedure. KCO behaves as transient liquid phase, providing microstructural benefits, vanishing during sintering. Electrical resistivity was improved by enhanced grains connectivity and growth. Significant increase in Seebeck coefficient at high temperatures has been produced while lattice thermal conductivity was unaffected. The best ZT value, estimated at 800°C, assuming the thermal conductivity value at 140°C, is 0.35 for 5wt.% KCO samples. These values are significantly higher than that obtained in highly-dense textured materials at the same temperature. The results suggest that this approach is very effective for preparing highly-performing CaCoO-based thermoelectric materials with relatively high porosity to control thermal conductivity., The authors wish to thank the MINECO-FEDER (MAT2013-46505-C3-1-R) and Gobierno de Aragón-Fondo Social Europeo (Research Groups T12 and T87) for financial support. This research was also partially supported by FCT, Portugal (IF/00302/2012 and PEst-C), project RECI/CTM-CER/0336/2012 co-financed by FEDER, QREN reference COMPETE: FCOMP-01-0124-FEDER-027465, and the projects financed by national funds through the FCT/MEC: UID/CTM/50025/2013, UID/CTM/50011/2013., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Thermoelectric properties of directionally grown Bi2Ba2Co2Oδ/Ag composites: effect of annealing

  • Rasekh, Sh.
  • Sotelo, Andres
  • Torres, M. A.
  • Bosque, P.
  • Madre, M. A.
  • Diez, J. C.
Bi2Ba2Co2Oδ thermoelectric ceramics with Ag additions (0, 1, 3, and 5 wt%) have been successfully textured using the laser floating zone method. Microstructure has shown that samples are composed by thermoelectric grains, together with a high amount of secondary phases, and that 3 wt% Ag addition leads to the best grain orientation. These microstructural benefits have been reflected in the highest thermoelectric performances determined in these samples. It has also been found that annealing procedure leads to a drastic decrease of secondary phases amount and raises the oxygen content in the thermoelectric phase. These modifications are reflected in an important decrease of electrical resistivity, ρ (compared to the as-grown samples) without drastic modification of Seebeck coefficient, S. As a consequence, the highest thermoelectric performances, determined through the power factor, have been reached in the 3 wt% Ag textured and annealed samples in the whole measured temperature range. The maximum PF (=S/ρ) values at 650 °C determined in these samples are very close to the highest reported in single crystals or very low rate LFZ grown Bi2Ba2Co2Oδ compounds, making them very attractive for practical applications., This research has been supported by the Spanish MINECO-FEDER (MAT2013-46505-C3-1-R). The authors wish to thank the Gobierno de Aragón and Fondo Social Europeo (Consolidated Research Groups T87 and T12) for financial support., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Thermoelectrics, Metallic Ag microsphere in a ceramic matrix

  • Madre, M. A.
  • Rasekh, Sh.
  • Torres, M. A.
  • Diez, J. C.
  • Sotelo, Andres
The authors would like to thank MINECO-FEDER (Project MAT2013-46505-C3-1-R) and Gobierno de Aragón and Fondo Social Europeo (Research Groups T12 and T87) for financial support., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Improved thermoelectric performances in textured Bi1.6Pb0.4Ba2Co2Oy/Ag composites

  • Sotelo, Andres
  • Rasekh, Sh.
  • Torres, M. A.
  • Bosque, P.
  • Madre, M. A.
  • Diez, J. C.
BiPbBaCoO thermoelectric ceramics with small Ag additions (0, 1, 3, and 5 wt%) have been textured using the laser floating zone method. Microstructure has shown a slight decrease on the secondary phases content and a better grain alignment in Ag added samples. These microstructural features are reflected in the thermoelectric properties, which have shown a significant decrease of electrical resistivity, when the Ag content is raised. In spite of a corresponding decrease of Seebeck coefficient, all the Ag-containing samples possess higher Power Factor values than the BiPbBaCoO ones. Moreover, the maximum Power Factor values (about 0.36 mW/K.m at 650 °C) have been measured in BiPbBaCoO+3 wt% Ag samples, which are the best results reported in this family of materials., This research has been supported by the MINECO-FEDER (Project MAT2013-46505-C3-1-R). The authors wish to thank the Gobierno de Aragón (Consolidated Research Groups T87 and T12) for financial support., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Improvement of structural and superconducting properties of Bi-2212 textured rods by substituting sodium

  • Nane, O.
  • Özçelik, Bekir
  • Sotelo, Andres
  • Madre, M. A.
In this paper, the physical and superconducting properties of BiSrCaNaCuO with x=0.0, 0.05, 0.075, 0.1, and 0.20 textured superconducting fiber rods prepared by a laser floating zone (LFZ) technique were studied. The effects of Na substitution for Ca have been investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), transport measurements, dc-magnetization, magnetic hysteresis and magnetic critical current density. The powder XRD patterns of samples have indicated that Bi-2212 phase is the major one, independently of Na content. The best critical temperature, T, has been found as 93.3 K from M-T data for the sample with 0.075 Na substitution. The maximum magnetic J value has been calculated as 1.35×10 A/cm at 10 K for the 0.10 Na sample. The maximum transport critical current density has directly been measured as 1.3×10 A/cm at 77 K for the 0.05Na sample., This work is supported by Research Fund of Çukurova University, Adana, Turkey, under Grant contracts no: FBA-2015-3934. M. A. Madre and A. Sotelo wish to thank the Gobierno de Aragón and Fondo Social Europeo (Grupo de Investigacion Consolidado T12) and MINECO-FEDER (project MAT2013-46505-C3-1-R) for financial support. M. A. Madre also acknowledges funding from MINECO-FEDER (Project ENE2014-52105-R)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

High thermoelectric performance in Bi2-xPbxBa2Co2Oy promoted by directional growth and annealing

  • Madre, M. A.
  • Costa, F. M.
  • Ferreira, Nuno M.
  • Rasekh, Sh.
  • Torres, M. A.
  • Diez, J. C.
  • Amaral, Vitor S.
  • Amaral, J.S.
  • Sotelo, Andres
Bi2-xPbxBa2Co2Oy (x=0.0, 0.2, 0.4, and 0.6) misfit compounds were grown by the laser floating zone technique. Microstructural analysis has shown the formation of thermoelectric grains together with high amount of secondary phases. Thermoelectric grains orientation is increased until 0.4Pb, while further substitution drastically destroys the preferential grain orientation. Electrical resistivity is very low compared with the values obtained in sintered materials, spectacularly increasing power factor. Moreover, the performance of these materials was further improved subjecting the as-grown samples to a postannealing step due to the rise of thermoelectric phase content. These microstructural modifications led to a high decrease of electrical resistivity, improving power factor in around a factor two at room temperature, compared with the as-grown samples. Moreover, the low thermal conductivity of the textured annealed samples leads to a maximum estimated ZT value of 0.53 for the 0.2 Pb-doped samples, much higher than the reported in literature., This research has been supported by the Spanish MINECO-FEDER (MAT2013-46505-C3-1-R). The authors wish to thank the Gobierno de Aragón-Fondo Social Europeo (Consolidated Research Groups T12 and T87) for financial support and to C. Gallego, C. Estepa and J. A. Gomez for their technical assistance. The authors also acknowledge the PEst-C/CTM/LA 25/2013-14, RECI/CTM-CER/0336/2012 co-financed by FEDER, QREN reference COMPETE: FCOMP-01-0124-FEDER-027465, “Facing the challenges of characterizing novel thermal materials and processes (Heat@UA)” and CICECO-Aveiro Institute of Materials (Ref. FCT UID /CTM /50011/2013) funding., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effect of Yttrium substitution on superconductivity in Bi-2212 textured rods prepared by a LFZ technique

  • Özçelik, Bekir
  • Nane, O.
  • Sotelo, Andres
  • Madre, M. A.
In this study, the physical and superconducting properties of the Bi2Sr2Ca1−xYxCu2O8+δ with x=0.0, 0.05, 0.075 0.1, and 0.20 textured superconducting rods prepared by a laser floating zone technique were presented. The effects of Y3+ substitution for Ca2+ have been investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), dc-magnetization, magnetic hysteresis and critical current density calculation by using the Bean׳s critical state model. The powder XRD patterns of the samples have shown the Bi-2212 phase is the major one. Along with the powder samples, the textured rod surfaces also were investigated by XRD. The grains found to be well-oriented along the longitudinal rod axis which is a typical result for superconductors prepared by laser floating zone (LFZ) method, has been observed. The best critical temperature, TC, has been found as 92.9 K for the sample with 0.15Y substitution, under DC magnetic field of 50 Oe in ZFC mode. It has also been observed that the critical current density decreases with increasing Y-substitution. Using those values, the maximum JC value has been determined as 2.37×105 A/cm2 for the undoped sample., This work is supported by Research Fund of Çukurova University, Adana, Turkey, under Grant contracts nos.: FBA-2014-3500 and FBA-2015-3934. A. Sotelo and M.A. Madre acknowledge the Gobierno de Aragón and Fondo Social Europeo (Grupo de Investigacion Consolidado T12) and MINECO-FEDER (MAT2013-46505-C3-1-R) for financial support. M.A. Madre also acknowledges MINECO-FEDER (Project ENE2014-52105-R) for funding., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effect of Na substitution on superconducting properties of Bi-2212 ceramics prepared by Sinter-Forged process

  • Nane, O.
  • Özçelik, Bekir
  • Sotelo, Andres
  • Madre, M. A.
Bulk textured BiSrCaNaCuO (x = 0.0, 0.05, 0.075 0.1, 0.15, and 0.20) ceramics have been prepared by a polymer solution method followed by sinter-forging process. The microstructure and superconducting properties of textured samples were affected by Na substitution. According to XRD data, all samples show that Bi-2212 phase is the major one, and main peaks corresponded to the (00ℓ) diffractions confirming that the crystallographic c-axis is perpendicular to the surface. SEM micrographs showed that samples are composed of well-stacked and oriented grains. The best critical temperature, T, was measured as 85.6 K for x = 0.075. The critical current density Jc, values decrease gradually with the increase of applied magnetic field. The maximum calculated Jc was 1.38 × 10 A/cm at 10 K for 0.075 Na sample which is about four times higher than the 0.34 × 10 A/cm value determined for the pure sample. The anisotropic properties of these textured materials have been investigated using magnetic measurements., This work is supported by Research Fund of Çukurova University, Adana, Turkey, under grant contracts no: FBA-2014-3500. A. Sotelo and M.A. Madre acknowledge the Gobierno de Aragón and Fondo Social Europeo (Grupo de Investigacion Consolidado T12) and MINECO-FEDER (MAT2013-46505-C3-1-R) for financial support. M.A. Madre also acknowledges MINECO-FEDER (Project ENE2014-52105-R) for funding. Authors would like to acknowledge the use of Servicio General de Apoyo a la Investigación-SAI, Universidad de Zaragoza. This work is also supported by Research Fund of Hakkari University, Turkey, under grant contracts no: MF2014BAP1., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Enhanced electrical and thermoelectric properties from textured Bi1.6Pb0.4Ba2Co2Oy/Ag composites

  • Madre, M. A.
  • Rasekh, Sh.
  • Torres, M. A.
  • Bosque, P.
  • Diez, J. C.
  • Sotelo, Andres
Bi1.6Pb0.4Ba2Co2Oy/3 wt% Ag composites have been textured using the laser floating zone technique. Microstructural observations have shown the formation of relatively high amounts of secondary phases and cracks along the plate-like grains in the as-grown materials. In spite of these microstructural features, electrical properties have not been drastically decreased. Annealing of these as-grown rods has enhanced the grains connectivity, decreased the contents of the secondary phases, and healed the cracks, thereby increasing their electrical performances. It has been deduced that oxygen content in the thermoelectric phase has not been significantly modified through annealing, as demonstrated by the very similar Seebeck values at room temperature in the as-grown and annealed samples. As a consequence of the low electrical resistivity values in the annealed materials, they reached higher power factor values than the as-grown ones. The highest power factor at room temperature is in the range of those reported for single crystals, while at 650 °C, it is the highest reported in Bi–Ba–Co–O polycrystalline family so far., This research has been supported by the MINECO-FEDER (Project MAT2013-46505-C3-1-R). The authors wish to thank the Gobierno de Aragón-FEDER (Consolidated Research Groups T87 and T12) for their financial support., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

From nanosized precursors to high performance ceramics: The case of Bi2Ca2Co1.7Ox

  • Madre, M. A.
  • Rasekh, Sh.
  • Salvador, C.
  • Torres, M. A.
  • Bosque, P.
  • Diez, J. C.
  • Sotelo, Andres
et al., Bi2Ca2Co1.7Ox thermoelectric ceramics were prepared by four different synthesis routes: coprecipitation with ammonium carbonate or oxalic acid, attrition milling, and solid state (as reference). Microstructure showed that coprecipitation and attrition milling produced sintered materials with less porosity and smaller particle sizes than the solid state ones. Thermoelectric properties reflect the microstructure, leading to materials with lower electrical resistivity and higher Seebeck coefficient, when compared with the solid state ones. In spite of an increase in thermal conductivity in these samples due to their lower porosity, the maximum estimated Figure-of-Merit is higher than in sintered materials., The authors thank Gobierno de Aragón-Fondo Social Europeo (Grupos de Investigacion Consolidados T12 and T87) and MINECO-FEDER (MAT2013-46505-C3-1-R) for financial support. This work was also supported by “le Syndicat Mixte de la Côte d’Opale” and “la région Nord Pas de Calais”., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Long-term high-temperature stability of directionally grown [Bi2Ba2O4]p[CoO2] rods

  • Diez, J. C.
  • Madre, M. A.
  • Torres, M. A.
  • Rasekh, Sh.
  • Sotelo, Andres
[Bi2Ba2O4]p[CoO2] thermoelectric ceramics have been successfully grown from the melt using the laser floating zone method, followed by a thermal treatment at 700°C under air between 0 and 1532 h. The microstructural, thermoelectric, and mechanical properties were evaluated as a function of the thermal treatment length. Microstructure has shown that as-grown samples are composed of thermoelectric grains, together with a relatively high amount of secondary phases. Thermal treatment decreased the number and amount of secondary phases, producing nearly single-phase samples after 384 h. Consequently, the thermoelectric properties evaluated through the power factor showed a slight increase with the thermal treatment length, mainly due to the decrease of electrical resistivity, while the Seebeck coefficient was nearly unchanged. On the other hand, flexural strength was practically constant after 24 h thermal treatment., This research has been supported by the Spanish MINECO-FEDER (MAT2013-46505-C3-1-R). The authors wish to thank the Gobierno de Aragón and Fondo Europeo de Desarrollo Regional (Consolidated Research Groups T87 and T12) for financial support., We acknowledge support by the CSIC Open Access Publication Initiative through its Unit of Information Resources for Research (URICI)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effect of Na-doping on thermoelectric and magnetic performances of textured Bi2Sr2Co2Oy ceramics

  • Çetin, Gize
  • Özçelik, Bekir
  • Torres, M. A.
  • Madre, M. A.
  • Sotelo, Andres
Bi2Sr2-xNaxCo2Ox (x = 0.0, 0.025, 0.050, 0.075, 0.100, and 0.125) samples were prepared through the solid-state route and textured using the laser floating zone technique. Microstructural analysis of as-grown samples showed well oriented grains and a relatively high amount of secondary phases due to their incongruent melting. Annealing procedure has drastically decreased the number and amount of secondary phases. Moreover, Na-doping has further decreased the secondary phases content and improved grain alignment. These modifications have been reflected in a large decrease of electrical resistivity with the annealing procedure. The maximum power factor values have been obtained in 0.075 Na-doped annealed samples, 0.20 mW/K2m, which are much higher than the best values obtained in textured materials through hot uniaxial pressing. Magnetic properties were very similar for all samples, with paramagnetic Curie temperature and effective magnetic moment values of −48.6 K and ≈2 μB, respectively., This work is supported by Research Fund of Çukurova University, Adana, Turkey, under grant contracts no: FDK-2016-6105. The authors wish to thank the MINECO-FEDER (Project MAT2013-46505-C3-1-R), Universidad de Zaragoza (Project UZ2017-TEC-03), and the Gobierno de Aragón-FEDER (Research Groups T12 and T87) for financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

High thermoelectric performances of Bi–AE–Co–O compounds directionally growth from the melt, Altas prestaciones termoeléctricas en compuestos Bi-AE-Co-O crecidos direccionalmente desde el fundido

  • Diez, J. C.
  • Rasekh, Sh.
  • Madre, M. A.
  • Torres, M. A.
  • Sotelo, Andres
[EN]: Bi2AE2Co2Ox (AE = Ca, Sr, and Ba) thermoelectric compounds were grown from the melt by the laser floating zone technique. Microstructural analysis of as-grown samples has shown the formation of well-aligned thermoelectric grains together with a relative high amount of secondary phases. On the other hand, a short (24 h) thermal treatment (810 °C for Sr, 800 °C for Ca, and 750 °C for Ba) under air, raises of thermoelectric phase content through the recombination of the secondary ones. These microstructural modifications led to a large decrease of electrical resistivity, improving the power factor. These results have been compared with samples prepared by the conventional solid state method and with the best values reported in the literature. From these data, it is possible to deduce that the high thermoelectric characteristics obtained in these samples make them very attractive for practical applications., [ES]: Se han crecido materiales termoeléctricos de la familia Bi2AE2Co2Ox (AE = Ca, Sr y Ba) mediante la técnica de fusión zonal flotante inducida por láser. Los estudios microestructurales han revelado que las muestras crecidas están formadas por granos termoeléctricos bien alineados, acompañados de cantidades apreciables de fases secundarias. Por otro lado, la cantidad de fase termoeléctrica se ha aumentado mediante cortos (24 h) tratamientos térmicos (810 °C para el Sr, 800 °C para el Ca y 750 °C para el Ba) en aire, por reacción de las fases secundarias. Estas modificaciones microestructurales han originado una reducción de la resistividad eléctrica, mejorando el factor de potencia. Los resultados obtenidos se han comparado con los correspondientes a muestras preparadas mediante un proceso clásico en el estado sólido, así como con los mejores resultados que se pueden encontrar en la bibliografía. Todo ello indica que las muestras obtenidas en este trabajo pueden ser muy atractivas para aplicaciones prácticas., This research has been supported by the Spanish MINECO-FEDER (MAT2013-46505-C3-1-R). The authors wish to thank the Gobierno de Aragón and Fondo Europeo de Desarrollo Regional (Consolidated Research Groups T87 and T12) for financial support and to C. Gallego, and C. Estepa for their technical assistance., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Improvement of Bi2Sr2Co2Oy thermoelectric performances by Na doping

  • Çetin, Gize
  • Özçelik, Bekir
  • Nane, O.
  • Sotelo, Andres
  • Rasekh, Sh.
  • Torres, M. A.
  • Madre, M. A.
Bi2Sr2-xNaxCo2Oy thermoelectric materials with x = 0, 0.025, 0.05, 0.075, 0.10, 0.125, and 0.15 have been prepared by the classical solid state reaction. Microstructure has shown an important grain growth when Na is added, leading to very high bulk densities confirmed through density measurements. These modifications have produced a drastic decrease of electrical resistivity without significant modification of Seebeck coefficient. As a consequence, Power Factor has been increased in all Na-doped samples, reaching the maximum value (0.21 mW/K2.m at 650 °C) for 0.075 Na samples, which is fairly close to the reported for single crystals., This work is supported by Research Fund of Cukurova University, Adana, Turkey, under grant contracts no: FBA-2016-6626 and FDK-2016-6105. The Spanish authors thank the Gobierno de Aragón and Fondo Social Europeo (Grupo de Investigacion Consolidado T12) and MINECO-FEDER (MAT2013-46505-C3-1-R) for financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Improving bulk Ca3Co4O9 thermoelectric materials through Zr doping

  • Madre, M. A.
  • Rasekh, Sh.
  • Torres, M. A.
  • Diez, J. C.
  • Sotelo, Andres
Ca3Co4−xZrxOy polycrystalline ceramics with small Zr substitution have been prepared through the classical solid-state method. X-ray diffraction data have shown that all samples are composed only of Ca3Co4O9 and Ca3Co2O6 phases. Moreover, by increasing Zr substitution up to 0.07, Ca3Co2O6 phase content is decreased. Density measurements have revealed that all samples are very similar, with values around 74% of the theoretical density. Electrical resistivity is decreased in Zr-doped samples, with respect to the pure samples, while Seebeck coefficient is unchanged. Both factors lead to power factor values around 0.33 mW K−2 m−1 at 800°C in 0.07 Zr-doped samples, which are about 65% higher than those obtained for the undoped samples., The authors thank the Gobierno de Aragon-FEDER (Grupos de Investigacion Consolidados T12 and T87) and MINECO-FEDER (MAT2013-46505-C3-1-R) for the financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

New environmentally friendly Ba-Fe-O thermoelectric material by flexible laser floating zone processing

  • Ferreira, Nuno M.
  • Costa, F. M.
  • Kovalevsky, A. V.
  • Madre, M. A.
  • Torres, M. A.
  • Diez, J. C.
  • Sotelo, Andres
Ceramics with nominal BaFe12Ox composition were processed through laser floating zone technique from 25 to 200 mm/h growth rates. These processing conditions were found to promote microstructural differences between the outer and inner parts of the rods, being more pronounced at higher growth rates. Along with the higher microstructural inhomogeneity, the samples grown at 100 and 200 mm/h display reasonable n-type thermoelectric properties provided by BaFe18Ox phase formation. Their highest power factor measured at 800 °C is comparable to the best observed so far in oxide ceramic materials, with additional advantage of high abundance and low costs of Fe2O3, and BaCO3 precursors., A. Sotelo, M. A. Madre, J. C. Diez, and M. A. Torres acknowledge the Gobierno de Aragon (Grupos de Investigacion Consolidados T12 and T87), and the MINECO-FEDER (MAT2013-46505-C3-1-R) for funding. N.M. Ferreira, A.V. Kovalevsky and F.M. Costa acknowledge the i3N (UID/CTM/50025/2013) and CICECO-Aveiro Institute of Materials (UID/CTM/50011/2013), financed by FCT/MEC and FEDER under the PT2020 Partnership Agreement. The support from FCT (Portugal) grants SFRH/BPD/111460/2015 and IF/00302/2012, are also acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effect of Na substitution and Ag addition on the superconducting properties of Bi-2212 textured materials

  • Özçelik, Bekir
  • Nane, O.
  • Sotelo, Andres
  • Amaveda, H.
  • Madre, M. A.
The effect of Ag addition on the structural and superconducting properties of Bi2Sr2Ca0.925Na0.075Cu2Oy + x wt% Ag materials with x = 0, 1, 3, and 5 prepared by sol–gel method, followed by directional growth using the laser floating zone (LFZ) technique has been investigated. Powder XRD measurements demonstrate that all samples are composed by nearly single Bi-2212 phase. SEM micrographs and EDX results confirms that Bi-2212 is the major phase with minor amounts of a Bi-free one (Sr,Ca)CuO2 and metallic Ag. According to the magnetic results, Ag does not modify the superconducting critical temperature, T c , but significantly increases the magnetic hysteresis loop area. The magnetic critical current density is maximum in the 3 wt% Ag containing samples, due to the larger grain clusters found in these samples, reaching 2.1 × 105 A/cm2 at 10 K. Moreover, Ag addition also improves the rods mechanical properties, determined by three point bending tests. The highest bending stress is also reached in the 3 wt% Ag samples., This work is supported by Research Fund of Çukurova University, Adana, Turkey, under Grant Contracts No: FBA-2016-6626. M. A. Madre acknowledges MINECO-FEDER (Project ENE2014-52105-R) for funding. M. A. Madre and A. Sotelo acknowledge the MINECO-FEDER (Project MAT2013-46505-C3-1-R) and the Gobierno de Aragón (Consolidated Research Group T12) for financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effect of precursors on the microstructure and electrical properties of Bi2Ba2Co2O x

  • Sotelo, Andres
  • Torres, M. A.
  • Rasekh, Sh.
  • Madre, M. A.
  • Diez, J. C.
Bi2Ba2Co2O x thermoelectric materials have been prepared through three different synthesis methods. The corresponding precursors were obtained from a coprecipitation method using oxalic acid, attrition milling, and classical solid state method (used as reference). Microstructural studies of precursors have shown that the ones produced by coprecipitation and attrition milling led to smaller grain sizes than the ones obtained through ball milling. Infrared spectroscopy has demonstrated that a thermal treatment at 450 °C totally decomposes the metallic oxalates, producing a mixture of Bi and Co oxides, and Ba carbonate, the same average composition of the other precursors. After sintering procedure, it has been determined that the small grain size precursors produce high-density samples, reflected in a decrease of electrical resistivity without significant modification of the Seebeck coefficient. As a consequence, power factor values are more than two times higher than the measured in samples prepared by the classical solid state method. Moreover, the highest power factor values are in the order of the best reported in textured materials, demonstrating the critical role of precursors in the final properties of these materials., The authors wish to thank the Gobierno de Aragón-FEDER (Grupos de Investigacion Consolidados T12 and T87) and MINECO-FEDER (MAT2013-46505-C3-1-R) for the financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effect of synthesis process on the densification, microstructure, and electrical properties of Ca0.9Yb0.1MnO3 ceramics

  • Sotelo, Andres
  • Torres, M. A.
  • Madre, M. A.
  • Diez, J. C.
Ca0.9Yb0.1MnO3 thermoelectric materials have been prepared, through a classical solid‐state sintering method, from attrition‐ and ball‐milled precursors. After calcination step, microstructural observations have shown that attrition‐milled precursors possess much smaller particle sizes than the obtained by ball milling. Smaller precursors sizes lead to higher reactivity, producing higher density, hardness, and thermoelectric phase content in the sintered materials. The thermoelectric properties reflect the microstructural features, decreasing electrical resistivity in the attrition milling prepared samples without a drastic decrease in the Seebeck coefficient. As a consequence, power factor values are higher than the obtained in the classical solid‐state method samples. Moreover, the highest power factor values at 800°C are much higher than the best results obtained in this CaMnO3 family. As a result, it has been found that it is possible to tailor the thermoelectric properties of Ca0.9Yb0.1MnO3 ceramics by designing the appropriate preparation procedure while keeping in mind its industrial scalability., The authors thank the Gobierno de Aragon-FEDER (Grupos de Investigacion Consolidados T12 and T87) and MINECO FEDER (MAT2013-46505-C3-1-R) for financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effects of K substitution on thermoelectric and magnetic properties of Bi2Sr2Co2Oy ceramic

  • Çetin, Gize
  • Özçelik, Bekir
  • Torres, M. A.
  • Madre, M. A.
  • Sotelo, Andres
In this work, Bi2Sr2−xKxCo2Ox thermoelectric materials with x = 0.0, 0.025, 0.050, 0.075, 0.10, 0.125, and 0.15 have been produced through the classical solid-state reaction. SEM characterization has shown an improvement of microstructure and a porosity decrease with K substitution, leading to very high densities, confirmed by apparent density measurements. These modifications have been reflected in a drastic decrease of electrical resistivity with slight modification of Seebeck coefficient. As a consequence, power factor has been increased in all the K doped samples, reaching the maximum values (0.192 mW/K2 m at 650 °C) in 0.075 K containing samples, which is fairly close to the reported values in single crystals. Magnetic results have shown that all samples are paramagnetic above 50 K and below they undergo to an antiferromagnetic phase transition. From temperature dependence of magnetic hysteresis, it has been observed that the slope of curves and the magnitude of magnetization have been increased when the temperature is decreased., This work is supported by Research Fund of Çukurova University, Adana, Turkey, under Grant contracts no: FBA-2016-7204 and FDK-2016-6105. The Spanish authors thank the Gobierno de Aragón-FEDER (Grupos de Investigacion Consolidados T12 and T87) and MINECO-FEDER (MAT2013-46505-C3-1-R) for financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

General approach of the photothermoelectric technique for thermal characterization of solid thermoelectric materials

  • Touati, K.
  • Depriester, M.
  • Guilmeau, E.
  • Sotelo, Andres
  • Madre, M. A.
  • Gascoin, Franck
  • Sahraoui, A. H.
This work focuses on the photothermoelectric (PTE) technique allowing the thermal characterization of solid-state thermoelectric (TE) materials. Previously, this technique was restricted to TE materials having low electrical conductivities. Here, the PTE technique is extended and generalized to all solid-state TE materials with low or high electrical conductivities. This is achieved by taking into account the Gaussian shape of the thermal excitation source. The formalism of this new methodology is developed and the procedure for extracting thermal parameters is proposed. For illustration, two different TE materials are studied: with relatively high electrical conductivity (Bi2Te2.4Se0.6) and relatively low electrical conductivity (Bi2Ca2Co1.7O x ). The thermal properties of these two materials (thermal diffusivity, effusivity and conductivity) are found and compared to those obtained by the photothermal radiometry which is a well established technique. The good concordance between the results obtained by these two techniques demonstrates the relevance of the generalized PTE technique. One of the main advantages of this technique is its non use of an external sensor., This work was financially supported by ‘la région Hauts de France’, ‘le Syndicat Mixte de la Côte d’Opale’ and by the ‘Fond Européen de Développement Economique Régional’. M A Madre and A Sotelo acknowledge MINECO-FEDER (project MAT2013-46505-C3-1-R) and Gobierno de Aragon-FEDER (Grupo de Investigacion Consolidado T12) for financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

High mechanical and thermoelectric performances in hot-pressed CdO

  • Madre, M. A.
  • Torres, M. A.
  • Sotelo, Andres
High density bulk CdO polycrystalline thermoelectric ceramics have been prepared through a hot-pressing process. Density measurements have revealed that it reaches 99.5% of the theoretical one, in agreement with the observed microstructure. Microhardness has shown to have indentation size effect, decreasing when the load is raised. Electrical resistivity shows metallic-like behaviour until 650 °C and semiconducting-like one at higher temperatures while Seebeck coefficient increases in the metallic-like region and decreases in the semiconducting one. The maximum power factor values, 1.6 mW/K2m, have been achieved at about 650 °C. These values are the highest obtained in this family of materials, with the advantage of its low thermal treatment duration, when compared with the typical solid state sintering process., This research has been supported by the Spanish MINECO-FEDER (MAT2013-46505-C3-1-R). The authors wish to thank the Gobierno de Aragón-FEDER (Consolidated Research Groups T12 and T87) for financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Physical, electrical and magnetic properties of Cr doped Bi2Sr2Ca1Cu2−xCrxOy (Bi-2212) superconductors prepared by laser floating zone technique

  • Gün, Esen
  • Özkurt, B.
  • Özçelik, Bekir
  • Madre, M. A.
  • Sotelo, Andres
  • Diez, J. C.
The structural and magnetic properties evolution of Cr-doped Bi2Sr2CaCu2−xCrxOy ceramics (x = 0.0, 0.05, 0.1, and 0.25) have been investigated using XRD, SEM, DC resistivity and M–H measurements. X-ray diffraction studies have shown that all samples are mainly composed of Bi-2212 phase, indicating that Cr can be incorporated in its crystal structure. The microstructure of the highly Cr-doped samples showed that some impurity phases appear, decreasing the conductivity between the grains. T c (onset) and T c (offset) have been improved for x = 0.05 Cr doping, while 0.25 Cr doped samples are not superconducting. This behavior can be associated to changes in the hole concentration and/or the magnetic nature of Cr. The magnetic properties indicate that low Cr-doping enhances the loop widths. Additionally, the critical current densities, J c , of samples have been calculated by using the Bean’s critical state model. It has been found that there are important improvements in J c values between 0.2 and 0.9 T applied magnetic fields for 0.05 Cr doped samples., This work is supported by the BAP Research Fund of Mersin University, Mersin, Turkey, under Grant Contract No: 2017-1-TP3-2176. A. Sotelo, M. A. Madre, and J. C. Diez thank Gobierno de Aragón-FEDER (Grupos de Investigacion Consolidados T12 and T87), and MINECO-FEDER (MAT2013-46505-C3-1-R) for financial support. The use of Servicio General de Apoyo a la Investigación-SAI (Universidad de Zaragoza), MEİTAM Central Laboratory (Mersin University), and METU Central Laboratory (Middle East Technical University, Ankara) are also acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Preparation of high performance Bi2Sr2Co1.8Ox thermoelectric materials from nanosized precursors

  • Sotelo, Andres
  • Rasekh, Sh.
  • Torres, M. A.
  • Madre, M. A.
  • Diez, J. C.
Bi2Sr2Co1.8Ox thermoelectric (TE) materials were prepared by three different synthesis methods producing nanosized precursors: coprecipitation (with ammonium carbonate or oxalic acid) and attrition milling, which were compared with those obtained by the classical solid state method. Microstructure has shown that precursors produced by coprecipitation and attrition milling methods produced nanometric precursors much smaller than the typical sizes produced by the solid state route. The TE properties are in agreement with the microstructural features, leading to lower resistivity in all the samples, compared with the solid state ones, while Seebeck coefficient is practically unchanged in all cases. As a consequence, maximum power factor values of around four times higher than those obtained in the classical solid state method have been determined. Moreover, the highest power factor value at 650°C is higher than the best results obtained in as-grown textured materials produced by the laser floating zone technique., The authors thank the Gobierno de Aragón-FEDER [Grupos de Investigacion Consolidados T12 and Grupos de Investigacion Consolidados T87] and MINECO-FEDER [MAT2013-46505-C3-1-R] for the financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Relationship between microstructure and superconducting properties in hot-pressed Bi-2212/Ag ceramic composites

  • Kahraman, F.
  • Sotelo, Andres
  • Madre, M. A.
  • Diez, J. C.
  • Özkurt, B.
  • Rasekh, Sh.
Microstructure and superconducting properties of Bi2Sr2Ca1Cu2O8+δ+x wt% Ag (x=0 and 3) composite materials prepared by a sol–gel method and textured by a hot-pressing process have been investigated. Structural and microstructural studies have shown that Bi-2212/Ag composites exhibit better grain alignment, bigger grain sizes, and lower amount of secondary phases than the pure ones. These different microstructural features are reflected in the electrical properties which showed that room temperature resistivity and the transition width decrease when Ag is added, without modifying Tc values. Moreover, magnetic properties have shown that Ag addition increases, in an important manner, the M–H loops surface, leading to higher Jc values than the pure ones. This effect has been associated to the microstructural features which produce a decrease on the number of grain boundaries, together with a reinforcement of weak grain links with metallic Ag., The authors acknowledge financial support from the Gobierno de Aragón and the Fondo Social Europeo (Consolidated Research Groups T12 and T87) and MINECO-FEDER (Project MAT2013-46505-C3-1-R). The technical contribution of C. Estepa, and C. Gallego are also acknowledged. F. Kahraman acknowledges a financial Grant from the Council of Higher Education (YÖK) in Turkey for international mobility. Authors would like to acknowledge the use of Servicio General de Apoyo a la Investigación-SAI, Universidad de Zaragoza., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

High thermoelectric performance in Bi2-xPbxBa2Co2Oy promoted by directional growth and annealing

  • Madre, M.A.
  • Costa, F.M.
  • Ferreira, N.M.
  • Costa, S.I.R.
  • Rasekh, S.
  • Torres, M.A.
  • Diez, J.C.
  • Amaral, V.S.
  • Amaral, J.S.
  • Sotelo, A.
Bi2-xPbxBa2Co2Oy (x=0.0, 0.2, 0.4, and 0.6) misfit compounds were grown by the laser floating zone technique. Microstructural analysis has shown the formation of thermoelectric grains together with high amount of secondary phases. Thermoelectric grains orientation is increased until 0.4Pb, while further substitution drastically destroys the preferential grain orientation. Electrical resistivity is very low compared with the values obtained in sintered materials, spectacularly increasing power factor. Moreover, the performance of these materials was further improved subjecting the as-grown samples to a postannealing step due to the rise of thermoelectric phase content. These microstructural modifications led to a high decrease of electrical resistivity, improving power factor in around a factor two at room temperature, compared with the as-grown samples. Moreover, the low thermal conductivity of the textured annealed samples leads to a maximum estimated ZT value of 0.53 for the 0.2 Pb-doped samples, much higher than the reported in literature.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Thermoelectric doping effect in Ca3Co4-xNixO9 ceramics

  • Constantinescu, G.
  • Rasekh, S.
  • Torres, M.A.
  • Bosque, P.
  • Madre, M.A.
  • Sotelo, A.
  • Diez, J.C.
Ca3Co4-xNixO9 (x=0.01, 0.03, and 0.05) polycrystalline thermoelectric ceramics have been prepared by the classical solid state method. As a result of the Ni addition an increase in porosity has been detected. Moreover, the presence of Ni has been related with the increase of Ca2Co3O6 secondary phase and the appearance of a new NiO-CoO solid solution. However, for the 0.01-Ni doped samples an improvement in the thermoelectric performances has been measured. This effect has been related with a decrease in the resistivity values and an increase in the Seebeck coefficient. The raise in the power factor for the 0.01-Ni doped samples, compared with the undoped ones, is between 10 and 25% at 50 and 800 °C respectively. Moreover, the maximum power at 800 °C, around 0.25 mW/K2.m, is significantly higher than the best results obtained in Ni doped samples reported previously in the literature.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Role of Ag in textured-annealed Bi2Ca2Co1.7Ox thermoelectric ceramic

  • Flahaut, D.
  • Allouche, J.
  • Sotelo, A.
  • Rasekh, Sh.
  • Torres, M.A.
  • Madre, M.A.
  • Diez, J.C.
Bi2Ca2Co1.7Ox thermoelectric ceramics with small Ag additions (0, 1, 2, 3, 4, and 5 wt.%) have been successfully grown from the melt, using the laser floating zone method and subsequently annealed at 800 °C for 24 h. The microstructure has shown a reduction of the amount of secondary phases for Ag contents up to 4 wt.%. This microstructural evolution leads to a decrease of the electrical resistivity values until an Ag content of 4 wt.%, whereas Seebeck coefficient has been maintained unchanged. This is in agreement with the presence of metallic Ag in all samples, confirmed not only by Energy Dispersive Spectrometry but also by X-ray photoelectron and Auger spectroscopy. These electrical properties lead to maximum power factor values of about 0.30 mW/K2.m at 650 °C for the 4 wt.% Ag containing samples, which is among the best results obtained for this type of materials.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Thermoelectrics

  • Madre, M.A.
  • Rasekh, S.
  • Torres, M.A.
  • Diez, J.C.
  • Sotelo, A.
Metallic Ag microsphere in a ceramic matrix Thermoelectricity is the direct solid-state conversion between thermal and electrical energy, without any moving parts, due to the well-known Seebeck effect. Currently, more than half of the energy produced ends up in the form of wasted heat: thermoelectric harvesting and energy conversion constitutes an solution to improve the energy efficiency of classical industrial and domestic energy transforming processes, through thermoelectric modules.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Effect of Na substitution on superconducting properties of Bi-2212 ceramics prepared by Sinter-Forged process

  • Nane, O.
  • Özçelik, B.
  • Sotelo, A.
  • Madre, M. A.
Bulk textured Bi2Sr2Ca1-xNaxCu2Oy (x = 0.0, 0.05, 0.075 0.1, 0.15, and 0.20) ceramics have been prepared by a polymer solution method followed by sinter-forging process. The microstructure and superconducting properties of textured samples were affected by Na substitution. According to XRD data, all samples show that Bi-2212 phase is the major one, and main peaks corresponded to the (00l) diffractions confirming that the crystallographic c-axis is perpendicular to the surface. SEM micrographs showed that samples are composed of well-stacked and oriented grains. The best critical temperature, TC, was measured as 85.6 K for x = 0.075. The critical current density Jc, values decrease gradually with the increase of applied magnetic field. The maximum calculated Jc was 1.38 × 105 A/cm2 at 10 K for 0.075 Na sample which is about four times higher than the 0.34 × 105 A/cm2 value determined for the pure sample. The anisotropic properties of these textured materials have been investigated using magnetic measurements.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Long-term high-temperature stability of directionally grown [Bi2Ba2O4]p[CoO2] rods

  • Diez, J.C.
  • Madre, M.A.
  • Torres, M.A.
  • Rasekh, S.
  • Sotelo, A.
[Bi2Ba2O4]p[CoO2] thermoelectric ceramics have been successfully grown from the melt using the laser floating zone method, followed by a thermal treatment at 700°C under air between 0 and 1532 h. The microstructural, thermoelectric, and mechanical properties were evaluated as a function of the thermal treatment length. Microstructure has shown that as-grown samples are composed of thermoelectric grains, together with a relatively high amount of secondary phases. Thermal treatment decreased the number and amount of secondary phases, producing nearly single-phase samples after 384 h. Consequently, the thermoelectric properties evaluated through the power factor showed a slight increase with the thermal treatment length, mainly due to the decrease of electrical resistivity, while the Seebeck coefficient was nearly unchanged. On the other hand, flexural strength was practically constant after 24 h thermal treatment.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

High thermoelectric performances of Bi–AE–Co–O compounds directionally growth from the melt; [Altas prestaciones termoeléctricas en compuestos Bi-AE-Co-O crecidos direccionalmente desde el fundido]

  • Diez, J.C.
  • Rasekh, S.
  • Madre, M.A.
  • Torres, M.A.
  • Sotelo, A.E.
Bi2AE2Co2Ox (AE = Ca, Sr, and Ba) thermoelectric compounds were grown from the melt by the laser floating zone technique. Microstructural analysis of as-grown samples has shown the formation of well-aligned thermoelectric grains together with a relative high amount of secondary phases. On the other hand, a short (24 h) thermal treatment (810 °C for Sr, 800 °C for Ca, and 750 °C for Ba) under air, raises of thermoelectric phase content through the recombination of the secondary ones. These microstructural modifications led to a large decrease of electrical resistivity, improving the power factor. These results have been compared with samples prepared by the conventional solid state method and with the best values reported in the literature. From these data, it is possible to deduce that the high thermoelectric characteristics obtained in these samples make them very attractive for practical applications.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Improved thermoelectric performances in textured Bi1.6Pb0.4Ba2Co2Oy/Ag composites

  • Sotelo, A.
  • Rasekh, S.
  • Torres, M. A.
  • Bosque, P.
  • Madre, M. A.
  • Diez, J. C.
Bi1.6Pb0.4Ba2Co2Oy thermoelectric ceramics with small Ag additions (0, 1, 3, and 5 wt%) have been textured using the laser floating zone method. Microstructure has shown a slight decrease on the secondary phases content and a better grain alignment in Ag added samples. These microstructural features are reflected in the thermoelectric properties, which have shown a significant decrease of electrical resistivity, when the Ag content is raised. In spite of a corresponding decrease of Seebeck coefficient, all the Ag-containing samples possess higher Power Factor values than the Bi1.6Pb0.4Ba2Co2Oy ones. Moreover, the maximum Power Factor values (about 0.36 mW/K2.m at 650 °C) have been measured in Bi1.6Pb0.4Ba2Co2Oy+3 wt% Ag samples, which are the best results reported in this family of materials.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Improving bulk Ca3Co4O9 thermoelectric materials through Zr doping

  • Madre, M.A.
  • Rasekh, S.
  • Torres, M.A.
  • Diez, J.C.
  • Sotelo, A.
Ca3Co4-xZrxOy polycrystalline ceramics with small Zr substitution have been prepared through the classical solid-state method. X-ray diffraction data have shown that all samples are composed only of Ca3Co4O9 and Ca3Co2O6 phases. Moreover, by increasing Zr substitution up to 0.07, Ca3Co2O6 phase content is decreased. Density measurements have revealed that all samples are very similar, with values around 74% of the theoretical density. Electrical resistivity is decreased in Zr-doped samples, with respect to the pure samples, while Seebeck coefficient is unchanged. Both factors lead to power factor values around 0.33 mW K-2 m-1 at 800°C in 0.07 Zr-doped samples, which are about 65% higher than those obtained for the undoped samples.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Effect of Yttrium substitution on superconductivity in Bi-2212 textured rods prepared by a LFZ technique

  • Ozcelik, B.
  • Nane, O.
  • Sotelo, A.
  • Madre, M.A.
In this study, the physical and superconducting properties of the Bi2Sr2Ca1-xYxCu2O8+delta with x=0.0, 0.05, 0.075 0.1, and 0.20 textured superconducting rods prepared by a laser floating zone technique were presented. The effects of Y3+ substitution for Ca2+ have been investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), dc-magnetization, magnetic hysteresis and critical current density calculation by using the Bean''s critical state model. The powder XRD patterns of the samples have shown the Bi-2212 phase is the major one. Along with the powder samples, the textured rod surfaces also were investigated by XRD. The grains found to be well-oriented along the longitudinal rod axis which is a typical result for superconductors prepared by laser floating zone (LFZ) method, has been observed. The best critical temperature, T-C, has been found as 92.9 K for the sample with 0.15Y substitution, under DC magnetic field of 50 Oe in ZFC mode. It has also been observed that the critical current density decreases with increasing Y-substitution. Using those values, the maximum J(C) value has been determined as 2.37 x 10(5) A/cm(2) for the undoped sample.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Enhanced electrical and thermoelectric properties from textured Bi1.6Pb0.4Ba2Co2Oy/Ag composites

  • Madre, M. A.
  • Rasekh, Sh.
  • Torres, M. A.
  • Bosque, P.
  • Diez, J. C.
  • Sotelo, A.
Bi1.6Pb0.4Ba2Co2Oy/3 wt% Ag composites have been textured using the laser floating zone technique. Microstructural observations have shown the formation of relatively high amounts of secondary phases and cracks along the plate-like grains in the as-grown materials. In spite of these microstructural features, electrical properties have not been drastically decreased. Annealing of these as-grown rods has enhanced the grains connectivity, decreased the contents of the secondary phases, and healed the cracks, thereby increasing their electrical performances. It has been deduced that oxygen content in the thermoelectric phase has not been significantly modified through annealing, as demonstrated by the very similar Seebeck values at room temperature in the as-grown and annealed samples. As a consequence of the low electrical resistivity values in the annealed materials, they reached higher power factor values than the as-grown ones. The highest power factor at room temperature is in the range of those reported for single crystals, while at 650 °C, it is the highest reported in Bi–Ba–Co–O polycrystalline family so far.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

From nanosized precursors to high performance ceramics: the case of Bi2Ca2Co1.7Ox

  • Madre, M. A.
  • Rasekh, Sh.
  • Touati, K.
  • Salvador, C.
  • Depriester, M.
  • Torres, M. A.
  • Bosque, P.
  • Diez, J. C.
  • Sotelo, A.
Bi2Ca2Co1.7Ox thermoelectric ceramics were prepared by four different synthesis routes: coprecipitation with ammonium carbonate or oxalic acid, attrition milling, and solid state (as reference). Microstructure showed that coprecipitation and attrition milling produced sintered materials with less porosity and smaller particle sizes than the solid state ones. Thermoelectric properties reflect the microstructure, leading to materials with lower electrical resistivity and higher Seebeck coefficient, when compared with the solid state ones. In spite of an increase in thermal conductivity in these samples due to their lower porosity, the maximum estimated Figure-of-Merit is higher than in sintered materials.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Effect of Na substitution and Ag addition on the superconducting properties of Bi-2212 textured materials

  • Özçelik, B.
  • Nane, O.
  • Sotelo, A.
  • Amaveda, H.
  • Madre, M. A.
The effect of Ag addition on the structural and superconducting properties of Bi2Sr2Ca0.925Na0.075Cu2Oy + x wt% Ag materials with x = 0, 1, 3, and 5 prepared by sol–gel method, followed by directional growth using the laser floating zone (LFZ) technique has been investigated. Powder XRD measurements demonstrate that all samples are composed by nearly single Bi-2212 phase. SEM micrographs and EDX results confirms that Bi-2212 is the major phase with minor amounts of a Bi-free one (Sr, Ca)CuO2 and metallic Ag. According to the magnetic results, Ag does not modify the superconducting critical temperature, Tc, but significantly increases the magnetic hysteresis loop area. The magnetic critical current density is maximum in the 3 wt% Ag containing samples, due to the larger grain clusters found in these samples, reaching 2.1 × 105 A/cm2 at 10 K. Moreover, Ag addition also improves the rods mechanical properties, determined by three point bending tests. The highest bending stress is also reached in the 3 wt% Ag samples.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Composite Bi-2212/Ag Superconductors Grown by Laser Travelling Floating Zone at Low Rates

  • Diez, J.C.
  • Sotelo, A.
  • Rasekh, S.
  • Amaveda, H.
  • Torres, M.A.
  • Bosque, P.
  • Chocarro, C.
  • Madre, M.A.
Well-textured Bi2.02Sr2.02Ca0.98Cu1.99O x /2.9 wt % Ag composite samples have been grown by the laser floating zone at very low rates (1, 3, and 5 mm/h). The as-grown samples present superconducting behavior, as a result of being composed by long and well-textured Bi-2212 grains as major phase. After annealing, the samples do not dramatically increase their J C. This effect has been associated with the presence of long cracks along the ab planes of the superconducting grains. Even after annealing, the cracks have not been totally removed and, as a consequence, the critical current of the samples after the thermal treatment has only been improved in around 50 %, compared with the as-grown samples.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Decrease of electrical resistivity in Ca3Co4O9 thermoelectric ceramics by Ti doping

  • Torres, M.A.
  • Rasekh, Sh.
  • Bosque, P.
  • Constantinescu, G.
  • Madre, M.A.
  • Diez, J.C.
  • Sotelo, A.
Ca3Co4−xTixO9 polycrystalline thermoelectric ceramics with small amounts of Ti have been prepared by the classical solid state method. X-ray diffraction data have shown that Ca3Co4O9 is the major phase, with small amounts of the Ca3Co2O6 one. Moreover, they show that Ti has been incorporated into these two phases. Electrical resistivity decreases, compared with the values for undoped samples, until 0.03-Ti doped ones. Further Ti addition produces an increase of resistivity with respect to the 0.03 Ti doped samples. Seebeck coefficient does not appreciably change in all the measured temperature range, independently of Ti content. The improvement in electrical resistivity leads to about 55 % higher power factor values for the 0.03 Ti-doped samples than that obtained in the undoped ones. The maximum power factor at 800 °C, around 0.33 mW/K2 m, is slightly higher than the obtained in higher density samples, clearly indicating the good thermoelectric performances of these doped samples.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Use of laser technology to produce high thermoelectric performances in Bi2Sr2Co1.8Ox

  • Rasekh, S.
  • Costa, F.M.
  • Ferreira, N.M.
  • Torres, M.A.
  • Madre, M.A.
  • Diez, J.C.
  • Sotelo, A.
Bi2Sr2Co1.8Ox bulk polycrystalline ceramics were prepared by conventional sintering of powders, obtained by polymer solution method and by directional growth using the laser floating zone technique. Microstructural analysis showed randomly oriented grains in the classical sintered materials, while in the laser-textured samples well oriented crystals with the c-axis nearly perpendicular to the growth direction were observed. A significant reduction on electrical resistivity, compared with the sintered materials, was observed due to the decrease on the secondary phases content. As a consequence, a raise on the power factor of about 2 and 5 times, compared with the classically sintered samples, was obtained for the as-grown and annealed laser-textured samples, respectively. The maximum power factor obtained at 650 °C in the annealed laser-textured samples (∼0.20 mW/K2 m) is much higher than the best value obtained in sinter–forged textured materials at the same temperature.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Effect of Secondary Annealing Process on Critical Current Density in Highly Textured Bi-2212 Superconducting System

  • Aksan, M. A.
  • Madre, M. A.
  • Rasekh, S.
  • Constantinescu, G.
  • Torres, M. A.
  • Diez, J. C.
  • Sotelo, A.
  • Yakinci, M. E.
Bi-2212 samples prepared by a solid-state reaction technique have been grown from the melt using the laser floating zone method. After annealing the as-grown bars, the samples showed a good grain alignment and a high transport critical current density. Secondary annealing processes were performed on the annealed samples with the aim of producing Bi-2212 phase controlled decomposition. Hence, the Bi-2201 phase and the secondary phases, which act as effective pinning centers, were obtained with the secondary annealing process. After these thermal treatments, the transport critical current densities of samples significantly increased, when compared to the annealed ones. The maximum critical current density was achieved when the samples were subjected to secondary annealing at 680°C for 168 h with an improvement of ~80%, compared to the annealed ones. Moreover, it was found that magnetization of the secondarily annealed samples was also increased. The magnetic critical current densities in these secondary annealed samples were about 3 times higher than the values obtained for the annealed ones. These results clearly indicate that the secondary annealing processes lead to the formation of effective pinning centers in the bulk material.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Decrease of Ca3Co4O9+δthermal conductivity by Yb-doping

  • Kiirat, G.
  • Aksan, M.A.
  • Rasekh, Sh.
  • Madre, M.A.
  • Diez, J.C.
  • Sotelo, A.
In this study, the effect of Yb-substitution on the structural, electrical and thermal transport properties of the Ca 3Co 4O 9 þ δ system has been investigated in the low temperature region (between 10 and 300 K). The resistivity of samples increases with raising the Yb-concentration in the system. All the samples show a metal-semiconductor transition below 85 K. In the analysis based on Strongly Correlated Fermi Liquid Model, an increased bandwidth and a reduced electronic correlation are found. It has also been found that the energy gap, E0, value also decreases with Yb substitution. The samples show positive thermoelectric power, indicating that dominant charge carriers are holes in all the samples. The thermoelectric power value decreases with Yb-substitution. From Mott equation, it is determined that the Fermi energy and hole concentration decrease in the Yb-susbtituted samples, compared to the undoped ones. Thermal conductivity, κ, is decreased in about 50% of the measured in undoped samples for the 0.01 and 0.03 Yb-doped samples at 300 K. Highest figure of merit, ZT, value is found to be 5.4 10 3 at 300 K for the unsubstituted sample and the ZT value decreases by the substitution.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Textured Pb-Doped Bi-2212 Superconductors for Current Limiters

  • Sotelo, A.
  • Rasekh, Sh.
  • Amaveda, H.
  • Bosque, P.
  • Torres, M.A.
  • Madre, M.A.
  • Diez, J.C.
Bi2−x Pb x Sr2CaCu2O y (x = 0.0, 0.3, 0.4, and 0.5) textured materials have been prepared by the laser floating zone technique. The E − I curves showed and increase of the slope of the normal to superconducting transition with Pb addition. The best values have been obtained for the 0.4 Pb-doped samples, around 16 at 77 K. In spite of this improvement, Pb addition decreased J C and T C in all cases. On the other hand, electrical characterization at lower temperatures has led to an impressive raise in the 0.4 Pb-doped samples, reaching n values around 31, and J C of about 3,000 A/cm 2, at 65 K. At the same time, the mechanical integrity of the vitreous precursor materials has been determined. All the obtained results clearly indicate that these precursors, when properly processed by the laser floating technique, are promising candidates for practical applications as current limiters.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Improvement of Bi2Sr2Co2Oy thermoelectric performances by Na doping

  • Çetin Karakaya, G.
  • Ozçelik, Bekir
  • Nane, O.
  • Sotelo, A.
  • Rasekh, Sh.
  • Torres, M.A.
  • Madre, M.A.
Bi2Sr2-xNaxCo2Oy thermoelectric materials with x = 0, 0.025, 0.05, 0.075, 0.10, 0.125, and 0.15 have been prepared by the classical solid state reaction. Microstructure has shown an important grain growth when Na is added, leading to very high bulk densities confirmed through density measurements. These modifications have produced a drastic decrease of electrical resistivity without significant modification of Seebeck coefficient. As a consequence, Power Factor has been increased in all Na-doped samples, reaching the maximum value (0.21 mW/K2.m at 650 °C) for 0.075 Na samples, which is fairly close to the reported for single crystals.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Enhancement of mechanical and thermoelectric properties of Ca3Co4O9 by Ag addition

  • Kahraman, F.
  • Madre, M. A.
  • Rasekh, S.
  • Salvador, C.
  • Bosque, P.
  • Torres, M. A.
  • Diez, J. C.
  • Sotelo, A.
Ca3Co4O9+x wt.% Ag (x=0, 1, 3, 5, and 10) polycrystalline thermoelectric ceramics have been prepared by a sol-gel route via nitrates followed by high temperature treatment before sintering. Out-of-plane XRD data have shown that major phase is the Ca3Co4O9 one, accompanied by metallic Ag. SEM observations have agreed with the XRD data. Apparent density measurements have revealed that all samples possess densities ranging between 80% and 90% when Ag content is raised. Mechanical properties have shown a drastic increase of bending stress when Ag is added to the samples. Electrical resistivity decreases with the Ag content, compared with the pure ones, while Seebeck coefficient slightly decreases. Maximum power factor values around 0.43mW/K2m at 800°C have been achieved for the 10wt.% Ag samples which is much higher than the measured in the pure Ca3Co4O9 samples.