Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

High-accuracy compliance correction for nonlinear mechanical testing: Improving Small Punch Test characterization

  • Sánchez-Ávila, David
  • Orozco-Caballero, A.
  • Martínez, Elkin
  • Portolés, Luis
  • Barea, Rafael
  • Carreño, Fernando
Small punch test, SPT, of metallic materials is a very convenient mechanical test since it requires a small volume of material. However, SPT data from different laboratories suffer from large scatter, mainly due to the different experimental set-ups, especially when displacement is measured without an LVDT. Such uncertainty is attributed predominantly to the large effect of elastic displacement associated to the low stiffness of the device set-up, which has not been taken properly into account so far. Additionally, we show that large stiffness variations during SPT are taking place. Thus, in this study, we present a methodology for performing the elastic correction in SPT load vs. displacement curves through a load-unload cycles test, allowing the attainment of the elastic displacement and associated stiffness for each unload step as a function of increasing SPT displacement. The proposed methodology provides SPT load vs. plastic displacement curves, which offer more accurate mechanical data and more reliable comparisons among different laboratories and materials, independently on the employed SPT set-up., Financial support from MINECO (Spain), Project MAT2015-68919- C3-1-R (MINECO/FEDER) is gratefully acknowledged. D. S´anchez-´Avila thanks Nebrija University for a PhD fellowship, and a research contract at CENIM, CSIC financed by the aforementioned project. A. Orozco- Caballero thanks also a research contract at CENIM, CSIC financed by same project., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Superplastic Behavior of Overaged 2024 Aluminum Alloy after Friction Stir Processing

  • Orozco-Caballero, A.
  • Álvarez Leal, Marta
  • Carreño, Fernando
  • Ruano, Oscar Antonio
A commercial 2024 aluminum alloy was heat treated at 280 °C for 48 h and then slow cooled in a furnace to obtain minimum hardness. This material was then friction stir processed (FSP) using three sets of processing conditions. To study the effect of the processing on the microstructure and the high temperature mechanical properties, the materials were tested in tension at an initial strain rate of 10¿2 s¿1 and temperature range 200 to 450 °C. Processing severity was selected as the main factor for obtaining fine grain sizes right after FSP. The grain size was enormously reduced from about 50 µm to 1 µm. This grain reduction gave rise to very high elongations to failure of about 400%. Strain¿rate-change tests showed a stress exponent close to 2 at intermediate strain rates, which was related to grain boundary sliding as the controlling deformation mechanism and to su- perplasticity, which is strongly grain-size dependent. A possible controlling deformation mechanism by solute-drag creep, as proposed by other authors, was disregarded since tests conducted at 450 °C, where the microstructure of the FSP materials coarsens rapidly, gave a low elongation to failure and high resistance, which showed the importance of the grain size dependence of the operative deformation mechanism at 250¿400 °C, which was only compatible with grain boundary sliding., Financial support from MINECO (Spain), Project MAT2015-68919-C3-1-R (MINECO/FEDER) is gratefully acknowledged. Funding from project PID2020-118626RB-I00 awarded by MCIN/AEI/10.13039/501100011033 is also acknowledged.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Superplasticity of a friction stir processed overaged WE54 magnesium alloy

  • Ruano, Oscar Antonio
  • Álvarez Leal, Marta
  • Orozco-Caballero, A.
  • Carreño, Fernando
The coarse-grained WE54 magnesium alloy was heat treated in order to have minimum hardness minimizing the effects of precipitates and solid solution. Friction stir processing (FSP) was applied in severe conditions to obtain ¿ne, equiaxed and highly misoriented grains, with grain sizes even less than 1 ¿m. The high severity of processing demonstrated to have a strong impact in the microstructure. Consequently, the processed materials exhibited excellent superplasticity at the high strain rate 10 ¿2 s ¿1 , and temperatures between 300 and 400 °C. The maximum tensile superplastic elongation of 756% was achieved at 400 °C thanks to the operation of grain boundary sliding mechanism (GBS). Besides the new data obtained through tensile testing, the paper deals with a transcendental question regarding the large differences in strain rate values at a given stress in the superplastic regime at maximum elongation compared to other magnesium-based alloys. With this is mind, 19 magnesium alloys from 22 different investigations were analyzed to give some light to this behavior that never was treated before. It is proposed that this behavior has to be attributed to the accommodation process, necessary for GBS to occur, which is hindered by reinforcing solutes., Financial support from MINECO (Spain), Project MAT2015–68919-C3–1-R (MINECO/FEDER) is gratefully acknowledged. A. Osingle bondC. also thanks CENIM, CSIC, for a contract funded by the aforementioned project and O.A.R. for a Professor ad honorem position. Pilar Rey at AIMEN (Spain) is acknowledged for assisting with friction stir processing. M. A-L. thanks MINECO for a FPI fellowship, number BES2013–063963 (MINECO/FEDER/ESF).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Improving the mechanical properties of a WE54 magnesium alloy through severe friction stir processing and rapid cooling

  • Orozco-Caballero, A.
  • Álvarez Leal, Marta
  • Ruano, Oscar Antonio
  • Carreño, Fernando
A commercial WE54 magnesium alloy was severely processed by FSP, lowering heat input, aiming to improve the mechanical properties, both strength and ductility. Additionally, a refrigerated backing anvil was used to warrant rapid cooling and maximize severity. The alloy was processed in two initial tempers, one was the as-received peak-aged T6 temper and the other one, TT, which aimed minimum feasible hardness. The microstructural characterization revealed grain sizes around 1 μm and high misorientation values. Tensile testing and ultramicroindentation after FSP revealed large strength and ductility improvement for both WE54 tempers. The results presented in the present research show that the mechanical performance of magnesium alloys can be improved by increasing processing severity, making the widespread use of these materials very competitive for the transport industry., Financial support from MINECO (Spain), Project MAT2015-68919-C3-1-R (MINECO/FEDER) is gratefully acknowledged. Pilar Rey at AIMEN is acknowledged for assisting with friction stir processing. A. O.-C. also thanks CENIM, CSIC, for a contract funded by the aforementioned project and O.A.R. for a Professor ad honorem position. M. A-L. thanks MINECO for a FPI fellowship, number BES2013-063963 (MINECO/FEDER/ESF). Finally, A. O.-C. thanks funding from Madrid Region (Comunidad de Madrid) through the Polytechnic University of Madrid (Universidad Politécnica de Madrid) in the line of Action for Encouraging Research from Young Doctors (project M190020074AOC, CAREDEL).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Influence of Solid Solutions on the Al2024 High-Temperature Deformation Behavior

  • Ruano, Oscar Antonio
  • Orozco-Caballero, A.
  • Álvarez Leal, Marta
  • Carreño, Fernando
The mechanical properties of 2024 aluminum alloy were studied after two different tempers. The T351 temper (solution heat treatment, stress relief, and natural aging) leads to high hardness and toughness. A thermal treatment consisting of heat-treating at 280 °C for 48 h and slow cooling in a furnace, named TT temper, was performed to increase the precipitate size and their separation while minimizing the amount of solutes in solid solution, which produced the minimum hardness for an overaged Al2024 alloy and a lower tensile flow stress than for the T351 temper. The flow stress strongly decreases and the elongation to failure strongly increases for both materials above 300 °C. Differences in strain rate at a given stress in the power law regime at all temperatures for both tempers and compared with pure aluminum are attributed to the influence of solutes in solid solutions, affecting both the glide and climb of dislocations. However, the stacking fault energy, SFE, alone does not account for the hot deformation behavior. Thus, it is the synergistic effect of various solutes that affects the entire deformation process, causing a decrease of three or four orders of magnitude in strain rate for a given stress with respect to the pure aluminum matrix values., Financial support from MINECO (Spain), Project MAT2015-68919-C3-1-R (MINECO/FEDER), is gratefully acknowledged. Funding from the project PID2020-118626RB-I00 awarded by MCIN/AEI/10.13039/501100011033 is also acknowledged. A. O-C. also thanks CENIM-CSIC for a contract funded by the MAT2015-68919-C3-1-R project and O.A.R. for a Professor ad honorem position. M. A-L. thanks MINECO for an FPI fellowship, number BES2013-063963 (MINECO/FEDER/ESF)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Predicting grain size-dependent superplastic properties in friction stir processed ZK30 magnesium alloy with machine learning methods

  • Bahari-Sambran, F.
  • Carreño, Fernando
  • Cepeda-Jiménez, C.M.
  • Orozco-Caballero, A.
The aim of this work is to predict, for the first time, the high temperature flow stress dependency with the grain size and the underlaid deformation mechanism using two machine learning models, random forest (RF) and artificial neural network (ANN). With that purpose, a ZK30 magnesium alloy was friction stir processed (FSP) using three different severe conditions to obtain fine grain microstructures (with average grain sizes between 2 and 3 µm) prone to extensive superplastic response. The three friction stir processed samples clearly deformed by grain boundary sliding (GBS) deformation mechanism at high temperatures. The maximum elongations to failure, well over 400% at high strain rate of 10 s, were reached at 400 °C in the material with coarsest grain size of 2.8 µm, and at 300 °C for the finest grain size of 2 µm. Nevertheless, the superplastic response decreased at 350 °C and 400 °C due to thermal instabilities and grain coarsening, which makes it difficult to assess the operative deformation mechanism at such temperatures. This work highlights that the machine learning models considered, especially the ANN model with higher accuracy in predicting flow stress values, allow determining adequately the superplastic creep behavior including other possible grain size scenarios., Financial support was obtained from Comunidad de Madrid through the Universidad Politécnica de Madrid in the line of Action for Encouraging Research from Young Doctors (project CdM ref: APOYO-JOVENES- 779NQU-57-LSWH0F , UPM ref M190020074AOC , CAREDEL), as well as MINECO (Spain) Project MAT2015-68919-C3-1-R (MINECO/FEDER) and project PID2020-118626RB-I00 (RAPIDAL) awarded by MCIN/AEI/10.13039/501100011033 . Pilar Rey (AIMEN) and Marta Álvarez-Leal (CENIM) are gratefully acknowl- edged for FSP assistance. FBS also thanks Project CAREDEL and Project RAPIDAL for research contracts and MCIN/AEI for a FPI contract number PRE2021-096977 ., Peer reviewed