Skip to main content

MATERIALES TERMOESTABLES AVANZADOS OBTENIDOS MEDIANTE METODOLOGIA CLICK

MAT2017-82849-C2-1-R

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2017
State Plan 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre UNIVERSITAT ROVIRA I VIRGILI

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Dielectric spectroscopy of novel thiol-ene/epoxy thermosets obtained from allyl-modified hyperbranched poly(ethyleneimine) and diglycidylether of bisphenol A

  • Badia, J.D.
  • Acebo, C.
  • Gil-Castell, O.
  • Serra, A.
  • Teruel-Juanes, Roberto|||0000-0002-0190-4445
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] Dielectric Thermal Analysis (DETA) of a series of new thermoset obtained by click chemistry was performed. The new thermosets were obtained by a dual-curing process consisting in a first photochemical thiol-ene, followed by a thermal thiol-epoxy starting from an allyl-terminated hyperbranched poly(ethyleneimine) (HBPEI) and different proportions of diglycidylether of bisphenol A (DGEBA) and the corresponding stoichiometric proportions of pentaerythritol tetrakis (3-mercaptopropionate, PETMP). The dielectric behaviour was obtained experimentally supressing the conductive effects. Two sub-Tg intramolecular non-cooperative gamma and beta relaxations and an intermolecular cooperative alpha-relaxation were detected. The gamma-relaxation was ascribed to the dipole orientation of the terminal thiol groups. Two gamma relaxations gamma(epo) and gamma(ene) were observed, according to the influence of the surroundings. Only thermosets with a content of flexible HBPEI/PETMP domains higher than a 50% w/w showed the gamma(ene) relaxation at lower temperatures and higher frequencies. The beta-relaxation was a non-Johari-Goldstein relaxation, ascribed to the dipole transfer of the linear -CH2-O-(C=O)-CH2-CH2- groups of the thiol constrained in the glassy state. The alpha-relaxation was ascribed to the long-term segmental movements of the thermosets, occurring during the transition from the glassy to the rubbery stage. A synergic effect of reducing the rigidity and compactness of the thermosets by the reduction of aromatic moieties of the DGEBA/PETMP units, and the increase of the flexibility induced by the addition of HBPEI/PETMP units affected the macromolecular movement of the thermosets., European Regional Development Funds and the Spanish Ministry of Science, Innovation and Universities for ENE2017-86711-C3-1-R, MAT2017-82849-C2-1-R, ENE2014-53734-C2-1-R, UPOV13-3E-1947 and projects. Ministry of Education for the FPU13/01916) for O. Gil-Castell. Generalitat de Catalunya for the 2017-SGR-77 project. Generalitat Valenciana for the APOSTD14/041 for JD Badia and GRISOLIA/2012/003 for R. Teruel-Juanes.
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Controlled composite processing based on off-stoichiometric thiol-epoxy dual-curing systems with sequential heat release (SHR)

  • Fabregat Sanjuan, Albert|||0000-0002-2878-1369
  • Fernández Francos, Xavier|||0000-0002-3492-2922
  • Ferrando Piera, Francesc|||0000-0003-4450-2734
Control of curing rate and exothermicity during processing of thermosetting composite materials is essential in order to minimize the formation of internal stresses leading to mechanical and dimensional defects in the samples, especially in thick composite samples. It was recently proposed that sequential heat release, an approach based on the kinetic control of the curing sequence of dual-curing thermosets, would enable a step-wise release of the reaction heat and therefore a better control of conversion and temperature profiles during the crosslinking stage. In this article, it is shown experimental proof of this concept obtained by means of an instrumented mold that can be used for the processing of small samples with and without carbon fiber reinforcement. Safe processing scenarios have been defined by numerical simulation using a simplified two-dimensional heat transfer model and validated experimentally., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Controlled composite processing based on off-stoichiometric thiol-epoxy dual-curing systems with sequential heat release (SHR)

  • Fabregat Sanjuan, Albert
  • Fernández Francos, Xavier
  • Ferrando Piera, Francesc
Control of curing rate and exothermicity during processing of thermosetting composite materials is essential in order to minimize the formation of internal stresses leading to mechanical and dimensional defects in the samples, especially in thick composite samples. It was recently proposed that sequential heat release, an approach based on the kinetic control of the curing sequence of dual-curing thermosets, would enable a step-wise release of the reaction heat and therefore a better control of conversion and temperature profiles during the crosslinking stage. In this article, it is shown experimental proof of this concept obtained by means of an instrumented mold that can be used for the processing of small samples with and without carbon fiber reinforcement. Safe processing scenarios have been defined by numerical simulation using a simplified two-dimensional heat transfer model and validated experimentally., Peer Reviewed, Postprint (author's final draft)