Skip to main content

MATERIALES TERMOESTABLES AVANZADOS OBTENIDOS MEDIANTE METODOLOGIA CLICK

MAT2017-82849-C2-2-R

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2017
State Plan 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre UNIVERSITAT POLITECNICA DE CATALUNYA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 20
Encontrada(s) 1 página(s)

UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Remarkable Thermal Conductivity of Epoxy Composites Filled with Boron Nitride and Cured under Pressure

  • Moradi, Sasan|||0000-0002-3481-2889
  • Román Concha, Frida Rosario|||0000-0001-7435-2402
  • Calventus Solé, Yolanda|||0000-0002-6216-5420
  • Hutchinson, John M.|||0000-0003-0743-1260
This work demonstrates that the application of even moderate pressures during cure can result in a remarkable enhancement of the thermal conductivity of composites of epoxy and boron nitride (BN). Two systems have been used: epoxy-thiol and epoxy–diamine composites, filled with BN particles of different sizes and types: 2, 30 and 180 µm platelets and 120 µm agglomerates. Using measurements of density and thermal conductivity, samples cured under pressures of 175 kPa and 2 MPa are compared with the same compositions cured at ambient pressure. The thermal conductivity increases for all samples cured under pressure, but the mechanism responsible depends on the composite system: For epoxy–diamine composites, the increase results principally from a reduction in the void content; for the epoxy–thiol system with BN platelets, the increase results from an improved matrix-particle interface; for the epoxy–thiol system with BN agglomerates, which has a thermal conductivity greater than 10 W/mK at 44.7 vol.% filler content, the agglomerates are deformed to give a significantly increased area of contact. These results indicate that curing under pressure is an effective means of achieving high conductivity in epoxy-BN composites., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Densification: A route towards enhanced thermal conductivity of epoxy composites

  • Moradi, Sasan|||0000-0002-3481-2889
  • Román Concha, Frida Rosario|||0000-0001-7435-2402
  • Calventus Solé, Yolanda|||0000-0002-6216-5420
  • Hutchinson, John M.|||0000-0003-0743-1260
When an amorphous polymer is cooled under pressure from above its glass transition temperature to room temperature, and then the pressure is released, this results in a densified state of the glass. This procedure applied to an epoxy composite system filled with boron nitride (BN) particles has been shown to increase the density of the composite, reduce its enthalpy, and, most importantly, significantly enhance its thermal conductivity. An epoxy-BN composite with 58 wt% BN platelets of average size 30 µm has been densified by curing under pressures of up to 2.0 MPa and then cooling the cured sample to room temperature before releasing the pressure. It is found that the thermal conductivity is increased from approximately 3 W/mK for a sample cured at ambient pressure to approximately 7 W/mK; in parallel, the density increases from 1.55 to 1.72 ± 0.01 g/cm3. This densification process is much more effective in enhancing the thermal conductivity than is either simply applying pressure to consolidate the epoxy composite mixture before curing or applying pressure during cure but then removing the pressure before cooling to room temperature; this last procedure results in a thermal conductivity of approximately 5 W/mK. Furthermore, it has been shown that the densification and corresponding effect on the thermal conductivity is reversible; it can be removed by heating above the glass transition temperature and then cooling without pressure and can be reinstated by again heating above the glass transition temperature and then cooling under pressure. This implies that a densified state and an enhanced thermal conductivity can be induced even in a composite prepared without the use of pressure., This research was funded by a grant from the Spanish Ministerio de Economia y Competitividad, grant number MAT2017-82849-C2-2-R. The APC was funded by the research group’s contract research funds., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Dual-cured thermosets from glycydil methacrylate obtained by epoxy-amine reaction and methacrylate homopolymerization

  • Roig, Adrià
  • Ramis Juan, Xavier|||0000-0003-2550-7185
  • Flor López, Sílvia de la|||0000-0002-6851-1371
  • Serra Albet, Maria Àngels|||0000-0003-1387-0358
Dual-curing is a processing technology based in the combination of two polymerization processes and the proper selection of the formulation. This methodology allows the preparation of intermediate materials with tailored characteristics, which can be viscous-liquids or rubbery solids according to their application. Once applied, the second stage is performed leading to a high crosslinked network. Usually, different monomers are involved, and unreacted monomer are still present in the intermediate material. This monomer experiments polymerization during the second step, but it can drip or be exuded during storage. In the present work, a commercial monomer, glycidyl methacrylate has been selected, because of the presence in the same molecule of an epoxide group, which can react with amines in the first stage of the dual-curing, and a methacrylate group that can be thermally or photochemically homopolymerized to complete the curing process. Diglycidylether of bisphenol A has been added to obtain a gelled intermediate material. The evolution of both curing steps has been studied by DSC and FTIR. The stability of the intermediate material has been confirmed and the characteristics of intermediate and final material have been evaluated by TGA and DMTA., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

State of the art in dual-curing acrylate systems

  • Konuray, Ali Osman|||0000-0001-7281-006X
  • Fernández Francos, Xavier|||0000-0002-3492-2922
  • Ramis Juan, Xavier|||0000-0003-2550-7185
  • Serra Albet, Maria Àngels|||0000-0003-1387-0358
Acrylate chemistry has found widespread use in dual-curing systems over the years. Acrylates are cheap, easily handled and versatile monomers that can undergo facile chain-wise or step-wise polymerization reactions that are mostly of the “click” nature. Their dual-curing processes yield two distinct and temporally stable sets of material properties at each curing stage, thereby allowing process flexibility. The review begins with an introduction to acrylate-based click chemistries behind dual-curing systems and relevant reaction mechanisms. It then provides an overview of reaction combinations that can be encountered in these systems. It finishes with a survey of recent and breakthrough research in acrylate dual-curing materials for shape memory polymers, optical materials, photolithography, protective coatings, structured surface topologies, and holographic materials
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Sequential photo-thermal curing of (meth)acrylate-epoxy thiol formulations

  • Roig, Adrià
  • Flor López, Sílvia de la|||0000-0002-6851-1371
  • Ramis Juan, Xavier|||0000-0003-2550-7185
  • Serra Albet, Maria Àngels|||0000-0003-1387-0358
In this work, a novel dual-curing procedure has been developed. It is a combination of a first radical UV-initiated thiol-(meth)acrylate reaction, followed by a second thermal thiol-epoxy step catalysed by a base. Since (meth)acrylates can lead to homopolymerization by radical mechanism, the amount of thiol have to be optimized to reach crosslinked materials with Tgs above room temperature and good mechanical performance. It should be considered, that if the amount of thiol is too low, epoxy homopolymerization can take place. The use of glycidyl methacrylate in combination with trifunctional meth(acrylates) allow this system to gel in the 1st stage and avoid possible dripping or exudation of free monomers in the storage of the intermediate materials. We selected trimethylolpropane tris(3-mercaptopropionate) as the thiol, 2,2-dimethoxy-2- phenylacetophenone as UV initiator and 1-methylimidazole as the base catalyst, Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Novel hybrid poly(thiourethane)/POSS covalent adaptable networks

  • Guerrero, Federico
  • Flor López, Sílvia de la|||0000-0002-6851-1371
  • Ramis Juan, Xavier|||0000-0003-2550-7185
  • Santos, Jose-Ignacio
  • Serra Albet, Maria Àngels|||0000-0003-1387-0358
Hybrid organic-inorganic materials have been introduced as one of the strategies to improve mechanical properties and obtaining new high-performance polymeric materials. These materials present a synergism that meets the advantages of both organic and inorganic phases: hardness and strength of inorganic phase, and elasticity and toughness of the organic matrix [1] Thiols and isocyanate groups react to give thiourethane or thiocarbamate groups. Polythiourethane (PTUs) are analogous with sulphur of polyurethane (PUs), one of the most produced polymers in the world. Despite of their advantages over PUs, PTUs have been less studied than PUs. In previous studies of our group, it was demonstrated that trans-thiocarbamoylation exchange reactions between thiourethane groups leads to a vitrimeric-like behaviour to this knd of networked polymers improving the easily of recycling and reshaping them [2, 3]. The aim of this study is not only to improve the mechanical characteristics of PTUs but also to determine the effect of the inorganic reinforcement in the relaxation behaviour., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Thermal conductivity and cure kinetics of epoxy-boron nitride composites: A review

  • Hutchinson, John M.|||0000-0003-0743-1260
  • Moradi, Sasan|||0000-0002-3481-2889
Epoxy resin composites filled with thermally conductive but electrically insulating particles play an important role in the thermal management of modern electronic devices. Although many types of particles are used for this purpose, including oxides, carbides and nitrides, one of the most widely used fillers is boron nitride (BN). In this review we concentrate specifically on epoxy-BN composites for high thermal conductivity applications. First, the cure kinetics of epoxy composites in general, and of epoxy-BN composites in particular, are discussed separately in terms of the effects of the filler particles on cure parameters and the cured composite. Then, several fundamental aspects of epoxy-BN composites are discussed in terms of their effect on thermal conductivity. These aspects include the following: the filler content; the type of epoxy system used for the matrix; the morphology of the filler particles (platelets, agglomerates) and their size and concentration; the use of surface treatments of the filler particles or of coupling agents; and the composite preparation procedures, for example whether or not solvents are used for dispersion of the filler in the matrix. The dependence of thermal conductivity on filler content, obtained from over one hundred reports in the literature, is examined in detail, and an attempt is made to categorise the effects of the variables and to compare the results obtained by different procedures., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

New allyl-functional catalytic comonomers for sequential thiol-Michael and radical thiol-ene reactions

  • Konuray, Ali Osman|||0000-0001-7281-006X
  • Fernández Francos, Xavier|||0000-0002-3492-2922
  • Ramis Juan, Xavier|||0000-0003-2550-7185
  • Serra Albet, Maria Àngels|||0000-0003-1387-0358
Soft poly(thioether) thermosets have been synthesized by employing a two-step curing procedure based on click chemistry. The first stage of curing is a thiol-Michael addition between acrylates (or methacrylates) and thiols in excess, catalyzed by a set of novel tertiary amine catalyst comonomers with allyl functionality. Subsequently, the pendant allyl groups of the comonomer get incorporated into the polymer network by undergoing thiol-ene UV photopolymerization with the remaining thiols. The strong catalysis by the high concentration of tertiary amine groups facilitates quantitative conversions at the end of the first stage. All remaining functional groups are depleted after a short period of UV irradiation. Final materials are clear, transparent, and exhibit homogeneous network structures with alpha relaxation temperatures in the range 3–25¿°C. This sub-ambient relaxation temperature range suggests these materials may be suitable for coating applications where delicate substrates are involved such as plastic, wood and paper.
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Dual-curable vitrimers for 3d-printing

  • Romano, Angelo
  • Konuray, Ali Osman|||0000-0001-7281-006X
  • Roppolo, Ignazio
  • Sangermano, Marco
  • Fernández-Francos, Xavier
  • Ramis Juan, Xavier|||0000-0003-2550-7185
3D-printed objects can greatly benefit from the introduction of molecular structure undergoing dynamic bond exchange [1] or the use dual-curing processing [2], leading to a significant enhancement of mechanical properties and extended capabilities such as adhesion, reshaping, healing and recycling. We have developed a family of dual-curing 3D-printable materials based on acrylate homopolymerization for the printing stage and epoxy-acid reaction for the second thermal curing stage, with the purpose 1) having a stable intermediate material with desired reshaping and adhesion capabilities and 2) obtaining a network structure capable of undergoing dynamic work rearrangement promoted by transesterification between ester and available hydroxyl groups. A latent amine catalyst has been added in order to accelerate both the thermal curing stage and transesterification, Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Controlled composite processing based on off-stoichiometric thiol-epoxy dual-curing systems with sequential heat release (SHR)

  • Fabregat Sanjuan, Albert|||0000-0002-2878-1369
  • Fernández Francos, Xavier|||0000-0002-3492-2922
  • Ferrando Piera, Francesc|||0000-0003-4450-2734
Control of curing rate and exothermicity during processing of thermosetting composite materials is essential in order to minimize the formation of internal stresses leading to mechanical and dimensional defects in the samples, especially in thick composite samples. It was recently proposed that sequential heat release, an approach based on the kinetic control of the curing sequence of dual-curing thermosets, would enable a step-wise release of the reaction heat and therefore a better control of conversion and temperature profiles during the crosslinking stage. In this article, it is shown experimental proof of this concept obtained by means of an instrumented mold that can be used for the processing of small samples with and without carbon fiber reinforcement. Safe processing scenarios have been defined by numerical simulation using a simplified two-dimensional heat transfer model and validated experimentally., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Thermal conductivity and cure kinetics of epoxy-boron nitride composites: A review

  • Hutchinson, John M.
  • Moradi, Sasan
Epoxy resin composites filled with thermally conductive but electrically insulating particles play an important role in the thermal management of modern electronic devices. Although many types of particles are used for this purpose, including oxides, carbides and nitrides, one of the most widely used fillers is boron nitride (BN). In this review we concentrate specifically on epoxy-BN composites for high thermal conductivity applications. First, the cure kinetics of epoxy composites in general, and of epoxy-BN composites in particular, are discussed separately in terms of the effects of the filler particles on cure parameters and the cured composite. Then, several fundamental aspects of epoxy-BN composites are discussed in terms of their effect on thermal conductivity. These aspects include the following: the filler content; the type of epoxy system used for the matrix; the morphology of the filler particles (platelets, agglomerates) and their size and concentration; the use of surface treatments of the filler particles or of coupling agents; and the composite preparation procedures, for example whether or not solvents are used for dispersion of the filler in the matrix. The dependence of thermal conductivity on filler content, obtained from over one hundred reports in the literature, is examined in detail, and an attempt is made to categorise the effects of the variables and to compare the results obtained by different procedures., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Novel hybrid poly(thiourethane)/POSS covalent adaptable networks

  • Guerrero, Federico
  • Flor López, Sílvia de la
  • Ramis Juan, Xavier
  • Santos, Jose-Ignacio
  • Serra Albet, Maria Àngels
Hybrid organic-inorganic materials have been introduced as one of the strategies to improve mechanical properties and obtaining new high-performance polymeric materials. These materials present a synergism that meets the advantages of both organic and inorganic phases: hardness and strength of inorganic phase, and elasticity and toughness of the organic matrix [1] Thiols and isocyanate groups react to give thiourethane or thiocarbamate groups. Polythiourethane (PTUs) are analogous with sulphur of polyurethane (PUs), one of the most produced polymers in the world. Despite of their advantages over PUs, PTUs have been less studied than PUs. In previous studies of our group, it was demonstrated that trans-thiocarbamoylation exchange reactions between thiourethane groups leads to a vitrimeric-like behaviour to this knd of networked polymers improving the easily of recycling and reshaping them [2, 3]. The aim of this study is not only to improve the mechanical characteristics of PTUs but also to determine the effect of the inorganic reinforcement in the relaxation behaviour., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

State of the art in dual-curing acrylate systems

  • Konuray, Ali Osman
  • Fernández Francos, Xavier
  • Ramis Juan, Xavier
  • Serra Albet, Maria Àngels
Acrylate chemistry has found widespread use in dual-curing systems over the years. Acrylates are cheap, easily handled and versatile monomers that can undergo facile chain-wise or step-wise polymerization reactions that are mostly of the “click” nature. Their dual-curing processes yield two distinct and temporally stable sets of material properties at each curing stage, thereby allowing process flexibility. The review begins with an introduction to acrylate-based click chemistries behind dual-curing systems and relevant reaction mechanisms. It then provides an overview of reaction combinations that can be encountered in these systems. It finishes with a survey of recent and breakthrough research in acrylate dual-curing materials for shape memory polymers, optical materials, photolithography, protective coatings, structured surface topologies, and holographic materials, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Sequential photo-thermal curing of (meth)acrylate-epoxy thiol formulations

  • Roig, Adrià
  • Flor López, Sílvia de la
  • Ramis Juan, Xavier
  • Serra Albet, Maria Àngels
In this work, a novel dual-curing procedure has been developed. It is a combination of a first radical UV-initiated thiol-(meth)acrylate reaction, followed by a second thermal thiol-epoxy step catalysed by a base. Since (meth)acrylates can lead to homopolymerization by radical mechanism, the amount of thiol have to be optimized to reach crosslinked materials with Tgs above room temperature and good mechanical performance. It should be considered, that if the amount of thiol is too low, epoxy homopolymerization can take place. The use of glycidyl methacrylate in combination with trifunctional meth(acrylates) allow this system to gel in the 1st stage and avoid possible dripping or exudation of free monomers in the storage of the intermediate materials. We selected trimethylolpropane tris(3-mercaptopropionate) as the thiol, 2,2-dimethoxy-2- phenylacetophenone as UV initiator and 1-methylimidazole as the base catalyst, Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

New allyl-functional catalytic comonomers for sequential thiol-Michael and radical thiol-ene reactions

  • Konuray, Ali Osman
  • Fernández Francos, Xavier
  • Ramis Juan, Xavier
  • Serra Albet, Maria Àngels
Soft poly(thioether) thermosets have been synthesized by employing a two-step curing procedure based on click chemistry. The first stage of curing is a thiol-Michael addition between acrylates (or methacrylates) and thiols in excess, catalyzed by a set of novel tertiary amine catalyst comonomers with allyl functionality. Subsequently, the pendant allyl groups of the comonomer get incorporated into the polymer network by undergoing thiol-ene UV photopolymerization with the remaining thiols. The strong catalysis by the high concentration of tertiary amine groups facilitates quantitative conversions at the end of the first stage. All remaining functional groups are depleted after a short period of UV irradiation. Final materials are clear, transparent, and exhibit homogeneous network structures with alpha relaxation temperatures in the range 3–25¿°C. This sub-ambient relaxation temperature range suggests these materials may be suitable for coating applications where delicate substrates are involved such as plastic, wood and paper., Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Densification: A route towards enhanced thermal conductivity of epoxy composites

  • Moradi, Sasan
  • Román Concha, Frida Rosario
  • Calventus Solé, Yolanda
  • Hutchinson, John M.
When an amorphous polymer is cooled under pressure from above its glass transition temperature to room temperature, and then the pressure is released, this results in a densified state of the glass. This procedure applied to an epoxy composite system filled with boron nitride (BN) particles has been shown to increase the density of the composite, reduce its enthalpy, and, most importantly, significantly enhance its thermal conductivity. An epoxy-BN composite with 58 wt% BN platelets of average size 30 µm has been densified by curing under pressures of up to 2.0 MPa and then cooling the cured sample to room temperature before releasing the pressure. It is found that the thermal conductivity is increased from approximately 3 W/mK for a sample cured at ambient pressure to approximately 7 W/mK; in parallel, the density increases from 1.55 to 1.72 ± 0.01 g/cm3. This densification process is much more effective in enhancing the thermal conductivity than is either simply applying pressure to consolidate the epoxy composite mixture before curing or applying pressure during cure but then removing the pressure before cooling to room temperature; this last procedure results in a thermal conductivity of approximately 5 W/mK. Furthermore, it has been shown that the densification and corresponding effect on the thermal conductivity is reversible; it can be removed by heating above the glass transition temperature and then cooling without pressure and can be reinstated by again heating above the glass transition temperature and then cooling under pressure. This implies that a densified state and an enhanced thermal conductivity can be induced even in a composite prepared without the use of pressure., This research was funded by a grant from the Spanish Ministerio de Economia y Competitividad, grant number MAT2017-82849-C2-2-R. The APC was funded by the research group’s contract research funds., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Dual-curable vitrimers for 3d-printing

  • Romano, Angelo
  • Konuray, Ali Osman
  • Roppolo, Ignazio
  • Sangermano, Marco
  • Fernández-Francos, Xavier
  • Ramis Juan, Xavier
3D-printed objects can greatly benefit from the introduction of molecular structure undergoing dynamic bond exchange [1] or the use dual-curing processing [2], leading to a significant enhancement of mechanical properties and extended capabilities such as adhesion, reshaping, healing and recycling. We have developed a family of dual-curing 3D-printable materials based on acrylate homopolymerization for the printing stage and epoxy-acid reaction for the second thermal curing stage, with the purpose 1) having a stable intermediate material with desired reshaping and adhesion capabilities and 2) obtaining a network structure capable of undergoing dynamic work rearrangement promoted by transesterification between ester and available hydroxyl groups. A latent amine catalyst has been added in order to accelerate both the thermal curing stage and transesterification, Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Remarkable Thermal Conductivity of Epoxy Composites Filled with Boron Nitride and Cured under Pressure

  • Moradi, Sasan
  • Román Concha, Frida Rosario
  • Calventus Solé, Yolanda
  • Hutchinson, John M.
This work demonstrates that the application of even moderate pressures during cure can result in a remarkable enhancement of the thermal conductivity of composites of epoxy and boron nitride (BN). Two systems have been used: epoxy-thiol and epoxy–diamine composites, filled with BN particles of different sizes and types: 2, 30 and 180 µm platelets and 120 µm agglomerates. Using measurements of density and thermal conductivity, samples cured under pressures of 175 kPa and 2 MPa are compared with the same compositions cured at ambient pressure. The thermal conductivity increases for all samples cured under pressure, but the mechanism responsible depends on the composite system: For epoxy–diamine composites, the increase results principally from a reduction in the void content; for the epoxy–thiol system with BN platelets, the increase results from an improved matrix-particle interface; for the epoxy–thiol system with BN agglomerates, which has a thermal conductivity greater than 10 W/mK at 44.7 vol.% filler content, the agglomerates are deformed to give a significantly increased area of contact. These results indicate that curing under pressure is an effective means of achieving high conductivity in epoxy-BN composites., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Dual-cured thermosets from glycydil methacrylate obtained by epoxy-amine reaction and methacrylate homopolymerization

  • Roig, Adrià
  • Ramis Juan, Xavier
  • Flor López, Sílvia de la
  • Serra Albet, Maria Àngels
Dual-curing is a processing technology based in the combination of two polymerization processes and the proper selection of the formulation. This methodology allows the preparation of intermediate materials with tailored characteristics, which can be viscous-liquids or rubbery solids according to their application. Once applied, the second stage is performed leading to a high crosslinked network. Usually, different monomers are involved, and unreacted monomer are still present in the intermediate material. This monomer experiments polymerization during the second step, but it can drip or be exuded during storage. In the present work, a commercial monomer, glycidyl methacrylate has been selected, because of the presence in the same molecule of an epoxide group, which can react with amines in the first stage of the dual-curing, and a methacrylate group that can be thermally or photochemically homopolymerized to complete the curing process. Diglycidylether of bisphenol A has been added to obtain a gelled intermediate material. The evolution of both curing steps has been studied by DSC and FTIR. The stability of the intermediate material has been confirmed and the characteristics of intermediate and final material have been evaluated by TGA and DMTA., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Controlled composite processing based on off-stoichiometric thiol-epoxy dual-curing systems with sequential heat release (SHR)

  • Fabregat Sanjuan, Albert
  • Fernández Francos, Xavier
  • Ferrando Piera, Francesc
Control of curing rate and exothermicity during processing of thermosetting composite materials is essential in order to minimize the formation of internal stresses leading to mechanical and dimensional defects in the samples, especially in thick composite samples. It was recently proposed that sequential heat release, an approach based on the kinetic control of the curing sequence of dual-curing thermosets, would enable a step-wise release of the reaction heat and therefore a better control of conversion and temperature profiles during the crosslinking stage. In this article, it is shown experimental proof of this concept obtained by means of an instrumented mold that can be used for the processing of small samples with and without carbon fiber reinforcement. Safe processing scenarios have been defined by numerical simulation using a simplified two-dimensional heat transfer model and validated experimentally., Peer Reviewed, Postprint (author's final draft)