Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 20
Encontrada(s) 1 página(s)

RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Tesis doctoral (DoctoralThesis)

Nuevos materiales de construcción ecosostenibles por su acción superhidrofugante

  • Martínez Carrascosa, Luis Antonio
La protección de materiales de construcción frente a la acción del agua, el principal vehículo de los agentes de degradación, es un factor clave para aumentar la vida útil de los edificios. En la actualidad existen materiales de construcción superhidrofugantes, los cuales poseen una elevada hidrofobicidad (como consecuencia de su una baja energía superficial) que evita la penetración de agua, y una alta repelencia (debido a una rugosidad característica de un estado Cassie-Baxter) que dota a los materiales de propiedades auto-limpiantes. Sin embargo, los materiales superhidrofugantes presentan dos inconvenientes principales: (1) su baja durabilidad, y (2) su escasa resistencia a contaminantes de naturaleza oleosa. En la presente Tesis Doctoral, se plantean soluciones a estos inconvenientes mediante el desarrollo productos, obtenidos por ruta sol-gel, que dotan a los materiales de construcción de propiedades innovadoras respecto a la durabilidad y la resistencia a contaminantes. Para ello, se han seguido dos líneas de investigación: 1. Materiales de construcción superhidrofugantes de elevada durabilidad. Se plantean dos estrategias. La primera de ellas ha sido desarrollar un producto superhidrofugante que contiene nanopartículas hidrófobas, unidas por un oligómero de sílice, lo que le confiere una elevada adhesión al sustrato. En la segunda aproximación, la superhidrofobicidad es obtenida mediante la aplicación de un producto hidrofugante y la posterior ablación láser de la superficie 2. Materiales de construcción con resistencia a contaminantes de naturaleza oleosa. En una primera aproximación se ha diseñado un producto que contiene nanopartículas de sílice y un fluoroalquilsilano, el cual dota a los materiales de propiedades oleofugantes. La siguiente estrategia consiste en producir materiales de construcción que presenten superoleofobicidad bajo agua, como consecuencia de la superhidrofilia foto-inducida en su superficie, mientras el interior del material mantiene su hidrofobicidad. Para ello se emplea un producto que contiene nanopartículas de TiO2 integradas en un gel de sílice modificado orgánicamente., Texto de los capítulos 1, 2, 7 y 8 en español.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Artículo científico (JournalArticle)

Producing C-S-H gel by reaction between silica oligomers and portlandite: A promising approach to repair cementitious materials

  • Zarzuela Sánchez, Rafael
  • Luna Aguilera, Manuel Jesús
  • Martínez Carrascosa, Luis Antonio
  • Yeste Siguenza, María del Pilar
  • Garcia-Lodeiro, Inés
  • Blanco-Varela, María Teresa
  • Cauqui López, Miguel Ángel
  • Rodríguez-Izquierdo Gil, José María
  • Mosquera Díaz, María Jesús
Impregnation treatments are one of the alternatives to protect concrete-based building and monuments from weathering degradation. However, it is important to consider the chemical compatibility of the reaction products with the building material. The impregnation product studied here consists of a silica oligomer able to poly- merize, by a simple sol-gel process, inside the pore structure of concrete. In this work, we investigate the ability of this impregnation treatment to produce C-S-H gel in contact with cement paste. A complete characterization of the reaction products demonstrated that the silanol groups from silica oligomers react with the portlandite present in the cement paste generating a material with the chemical, structural and morphological features of C- S-H gel. Simultaneously, the 29Si NMR results indicate that the SieO units are incorporated into the existing C-S- H, increasing its chain length. These results open the way for a simple concrete structures repairing procedure. 1.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Artículo científico (JournalArticle)

Characterization and Analysis of the Carbonation Process of a Lime Mortar Obtained from Phosphogypsum Waste

  • Romero-Hermida, M. I.
  • Borrero-López, Antonio María
  • Flores-Alés, V.
  • Alejandre, Francisco Javier
  • Franco, José María
  • Santos Sánchez, Alberto
  • Esquivias, L.
This work addresses the reuse of waste products as a raw material for lime putties, which are one of the components of mortar. 1:3 Lime/sand mortars very similar to conventional construction mortars were prepared using a lime putty obtained from the treatment of phosphogypsum with sodium hydroxide. The physical, rheological and mechanical properties of this phosphogypsum-derived mortar have been studied, as well as the mineralogical composition, microstructure by scanning electron microscope (SEM) and curing process by monitoring carbonation and ultrasonic propagation velocity. Considering the negative influence of sulphates on the hardened material, the behaviour of the material after sulphates precipitation by adding barium sulphate was additionally tested. Carbonation progressed from the outside to the inside of the specimen through the porous system by Liesegang rings patterns for mortars with soluble sulphates, while the carbonation with precipitated sulphates was controlled by diffusion-precipitation. Overall, the negative influence of low-sulphate contents on the mechanical properties of mortars was verified. It must be highlighted the importance of their precipitation to obtain adequate performance., This research was funded by Programa Estatal I+D+i Retos de la Sociedad of the Ministry of Science and Innovation (Spain), which supported this research (MAT2017-84228-R research project).
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Artículo científico (JournalArticle)

Compatibility, effectiveness and susceptibility to degradation of alkoxysilane-based consolidation treatments on a carbonate stone

  • Gemelli, Giada María Chiara
  • Zarzuela Sánchez, Rafael
  • Fernández, Federica
  • Mosquera Díaz, María Jesús
Alkoxysilane-based consolidation treatment are commonly employed in restoration and conservation works of Cultural Heritage buildings. However, their poor affinity to carbonate stones is well-known. In this paper, we evaluate three consolidant treatments (two of them modified to incorporate hydrophobic or photocatalytic properties), formulated to circumvent this drawback and their cracking during drying, through a surfactant- assisted synthesis. The consolidants were applied on Noto stone, a biocalcarenite (~95% CaCO3) employed in numerous Cultural Heritage buildings of Southern Italy. A comprehensive validation of the three consolidants, compared to a commercial TEOS based consolidant, was performed regarding their compatibility, effectiveness and susceptibility to degradation. The obtained results show that all consolidants improved the mechanical resistance of the stone, up to 6 mm for the commercial consolidant and up to 9 mm in depth for the surfactant- synthetized ones, though over-consolidation on the surface is a factor to watch for on the latter. Moreover, the treated stones exhibited a greater resistance to salts ingress respect to untreated ones related to the reduction in the smaller pores (0.1–2 μm range). In addition, all tested consolidants can be considered within the low and moderate incompatibility degree, though this factor is slightly higher than for the commercial one. Regarding the susceptibility to degradation, the surfactant-synthetized products experienced lower loss of consolidating effect, compared to the commercial one, after prolonged immersion in water and salts (sulphate) crystallization tests. However, the modification of the consolidant to obtain photocatalytic properties has a significant impact on its susceptibility against the latter.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Artículo científico (JournalArticle)

Incorporation of functionalized Ag-TiO2NPs to ormosil-based coatings as multifunctional biocide, superhydrophobic and photocatalytic surface treatments for porous ceramic materials

  • Zarzuela Sánchez, Rafael
  • Carbú Espinosa de los Monteros, María
  • Gil Montero, María Luisa Almoraima
  • Cantoral Fernández, Jesús Manuel
  • Mosquera Díaz, María Jesús
Microbial fouling on the surface and water retention are common problems affecting porous ceramic materials (stone, concrete…) that can alter their properties, shorten their service life and even pose a health risk. Though proper maintenance (disinfection, drainage…) can mitigate these issues, it is a time and resource intensive process and preventive measurements are desired, such as hydrophobic or anti-fouling coatings. In this work, we report a simple sol-gel route to obtain a multifunctional coating combining superhydrophobic, biocide and photoactive properties, by incorporating TiO2 nanoparticles (NPs), functionalized with –SH or –NH terminated alkoxysilanes, and AgNPs into an organically modified silica matrix (ormosil). The low surface energy of the ormosil, combined with the nano-roughness created by the accumulation of Ag-TiO2NPs on the surface promotes a Cassie-Baxter wetting state, leading to water repellence and a lower bioreceptivity of the coatings due to a decreased cell attachment. The influence of this factor was evidenced by the comparatively higher cell attachment on the smoother surface of xerogels samples prepared from the ormosils, where TiO2 surface charge plays a major role. The incorporation of AgNPs increases the photocatalytic effectiveness of the TiO2 and effectively inhibits the growth of the tested microorganisms (Escherichia coli and Saccharomyces cerevisiae), even in the absence of light. Surface functionalization of the TiO2NPs affects the distribution, size and stability of the AgNPs, and thus, the biocide and photocatalytic effectiveness of the treatments. 1.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Artículo científico (JournalArticle)

Effects of surface functionalization with alkylalkoxysilanes on the structure, visible light photoactivity and biocidal performance of Ag-TiO2 nanoparticles

  • Zarzuela Sánchez, Rafael
  • Moreno-Garrido, Ignacio
  • Gil Montero, María Luisa Almoraima
  • Mosquera Díaz, María Jesús
Surface-modified Ag/TiO2 photocatalysts with enhanced activity under visible light and biocidal properties have been produced through a two-stage method involving the functionalization ofTiO2 nanoparticles(NPs) with –SH or –NH terminated alkoxysilanes and deposition ofAgNPs. The functionalization process increased the yield of the Ag deposition and promoted a more homogeneous dis- tribution of the Ag over the TiO2 surface. The highest stability, homogeneity and visible range absorption was achieved by –NH functionalization. However, the modification with –SH groups alters the size of the AgNPs and decreases the effectiveness due to formation ofAg2S. The increased absorption in the visible spectrum accel- erated the organic dye degradation under solar light, although aggregation processes affected their effectiveness under UV-A. The incorporation of AgNPs allowed for the elimination of phototrophic microorganisms under white light at very low Ag concentrations whereas TiO2 and –SH functionalized Ag/TiO2 showed no biocidal activity.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Artículo científico (JournalArticle)

Chemistry of the interaction between an alkoxysilane-based impregnation treatment and cementitious phases

  • Garcia-Lodeiro, Inés
  • Carmona-Quiroga, P.M.
  • Zarzuela Sánchez, Rafael
  • Mosquera Díaz, María Jesús
  • Blanco-Varela, María Teresa
Chemical compatibility with a wide range of materials is among the features that has driven the use of alkox- ysilanes as consolidants in built structures. Such compatibility is particularly important in cementitious materials where the reaction with portlandite may generate C-S-H gel, one of the main hydration phases of OPC. The cementitious matrix is a complex system, however, and the reaction of its many phases with alkoxysilanes, while poorly understood, may determine treatment efficacy. This article describes a detailed study of the individual interactions between an oligomeric alkoxysilane-based impregnation treatment previously shown to interact with the portlandite present in cement paste and the cementitious phases generated in ordinary portland cement hydration. The findings show that both portlandite and C-S-H gel interact with the silicon oligomers in the hydrolysed impregnation treatment to generate a C-S-H gel (in the case of portlandite) and a rise in C-S-H gel mean chain length (MCL). Ettringite is also altered in the presence of alkoxysilanes, transforming to gypsum and AH3. Its transformation generates a tetrahedral aluminium that is taken up into a high silicon gel sourced from the treatment to form an amorphous aluminosilicate gel. Monocarboaluminate and katoite also partially decompose in the interaction with the product, whereas gibbsite remains unaffected
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Artículo científico (JournalArticle)

A Simple, Long-Lasting Treatment for Concrete by Combining Hydrophobic Performance with a Photoinduced Superhydrophilic Surface for Easy Removal of Oil Pollutants

  • Martínez Carrascosa, Luis Antonio
  • Zarzuela Sánchez, Rafael
  • Badreldin, Nabil
  • Mosquera Díaz, María Jesús
Superhydrophobic surfaces present promising applications in the protection of building materials, such as the self-cleaning effect promoted by their high water-repellent properties. However, these surfaces easily lose their properties when exposed to oil contaminants. This is a critical weak point for their application in building facades, which are exposed to environmental pollutants such as hydrocarbons and vandalism (e.g., grafitti). A viable strategy to remove oils is to produce superhydrophilic surfaces, which present underwater superoleo- phobic behavior. In the case of buildings, the use of this strategy can be considered counterproductive because it promotes their interaction with water, the main vehicle of most decay agents. In this work, we have successfully combined the advantages of a superhydrophilic coating with a hydrophobic impregnation treatment, which prevents water ingress into the porous structure of the substrate. Specifically, a photoinduced superhydrophilic surface was produced on concrete by simple spraying of a starting sol containing TiO2NPs, which create a Cassie-Baxter state, a silica oligomer, producing a compatible matrix promoting good adhesion to the substrate and polydimethylsiloxane as a hydrophobic agent. After being exposed to sunlight, the treated surfaces switched from superhydrophobic (SCA 160°) to superhydrophilic (SCA < 10°). These surfaces presented underwater superoleophobicity (SCA 152° with CHCl3) and oil-contaminated dust was easily cleaned without employing detergents. The photoactivation does not alter the protection against water absorption (>85% reduction). The treatment showed suitable adhesion to the substrate and good resistance
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Artículo científico (JournalArticle)

Cu-TiO2/SiO2 photocatalysts for concrete-based building materials: Self-cleaning and air de-pollution performance

  • Khannyra, Souad
  • Mosquera Díaz, María Jesús
  • Addou, Mohammed
  • Gil Montero, María Luisa Almoraima
As a consequence of human activities, today, we are exposed to high pollution levels that cause building materials damage and many diseases. The application of TiO2 as coating on building materials has proven the efficiency of self-cleaning and air de-pollution. However, its performance is limited due to its absorption being exclusively located at UV light. In this study, Cu-TiO2 photocatalysts were integrated into silica sol-gel synthesis to manufacture new long-lasting term coatings with self-cleaning and air purification properties for concretebased building materials. The enhancement of TiO2 photoactivity by incorporating Cu into its network has been clearly demonstrated. The self-cleaning and air de-polluting efficiency were assessed using methylene blue (MB), soot and NO, respectively, indicating that the presence of Cu promotes the TiO2 performance. For low doping levels, by increasing the copper loading, the TiO2 photoactivity increased. The highest efficiency was obtained by the photocatalyst containing 5% copper, which shows maximum destruction of methylene blue and soot of 95% and 50% within 60 min and 168 h of irradiation, respectively. However, higher copper loading led to a decrease in its performance, reaching a total degradation of MB and soot of 90% and 45% after 60 min and 168 h of irradiation, respectively, for the sample containing 15% of copper loading., This work has been supported by the Spanish Government/FEDEREUMAT2017-84228-R, MINECO/AEI/FEDER/UE) and PID2020115843RB-I00/AEI/10.13039/501100011033. This work has been cofinanced by the European Union under the 2014-2020 ERDF Operational Programme and by the Department of Economic Transformation, Industry, Knowledge, and Universities of the Regional Government of Andalusia. Project reference: FEDER-UCA18-106613. We want to thank Margarita Carballido, Mercedes Marquez and Sergio Moreno to facilitate the real exposure of the samples.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Artículo científico (JournalArticle)

Self-cleaning durability assessment of TiO2/SiO2 photocatalysts coated concrete: Effect of indoor and outdoor conditions on the photocatalytic activity

  • Khannyra, Souad
  • Luna Aguilera, Manuel Jesús
  • Gil Montero, María Luisa Almoraima
  • Addou, Mohammed
  • Mosquera Díaz, María Jesús
A self-cleaning nanostructured TiO2 coating has demonstrated the capacity to mitigate undesired effects from air pollution. Not only it reduces the deterioration of building materials but may also prevent certain pollution-related human health problems. In this study, mesoporous TiO2/SiO2 photocatalysts were synthesized in order to produce self-cleaning and long-lasting coatings that meet the necessary requirements for outdoor applications. The synthesized products were sprayed on concrete substrates and their self-cleaning and air depolluting capabilities were evaluated. The former one as a function of methylene blue (MB) and soot degradation and the latter, according to nitrogen oxides reduction. The coatings proved to have high photocatalytic activity, and their efficiency was enhanced as TiO2 loadings were increased. Thus, after the first 60 min of their irradiation by UV–vis light, the photocatalysts ST1 and S4T had removed 79% and 95% of the MB, respectively. These coatings presented particulate surfaces that provided more surface area and porosity, which are key factors for a high photocatalytic activity. Moreover, the same samples after 104 h of irradiation exhibited 38% and 49% conversion of total NO, respectively. While E503, a commercially available photocatalyst, produced coating cracked surfaces and a total MB degradation of just 50% after 60 min of irradiation as well as 35% of NO conversion after 104 h of irradiation. The TiO2/SiO2 coatings’ photocatalytic efficacy remained practically invariable after four months of exposure to real-life conditions and three MB degradation cycles. After the outdoor durability tests, the coated surfaces exhibited a practically unchanged structure, which confirms their long-lasting efficiency. © 2022 The Authors, This work has been supported by the Spanish Government MAT2017-84228-R (MINECO/AEI//FEDER, UE) and PID2020- 115843RB-I00/AEI/10.13039/501100011033 . This work has been co-financed by the European Union under the 2014–2020 ERDF Operational Programme and by the Department of Economic Transformation, Industry, Knowledge, and Universities of the Regional Government of Andalusia . Project reference: FEDER-UCA18-106613 .
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Artículo científico (JournalArticle)

Honeycomb filters as an alternative to powders in the use of clays to remove cadmium from water

  • Ahrouch, Mohammadi
  • Gatica Casas, José Manuel
  • Draoui, Khalid
  • Bellido Milla, Dolores
  • Vidal Muñoz, Hilario
Two natural Moroccan clays, an illite-smectite (O) and a stevensite (ST), were used to manufacture honeycomb monoliths for the removal of cadmium from aqueous solution. This goal was based on their easy extrudibility without additives and good performance for organic dyes and lead removal in previous studies. First, the influence of adsorbent dosage, time, pH and initial Cd(II) concentration was studied through batch experiments with the clay powders. Then, flow recirculation tests with the clays conformed as structured filters were performed. These confirmed the kinetics and adsorptive model, pseudo-second order and Langmuir, respectively, no matter the linear or non-linear character of the regression followed to fit the experimental data. With both experimental and sample designs, ST exhibited better performance than O. This could not be attributed to an exchange with Mg(II) overlapping the adsorption, despite its greater content in this element. Clay honeycombs behaved also better than packed columns charged with the same amount of powdered clay in similar experiments. Their maximum adsorption capacity (4 mg/g) ensures complete depuration of a solution containing 150 ppm of Cd(II) after recirculation through a 10 cm long and 3 cm-diameter monolith with the help of a centrifugal pump for less than 10 h., Ministry of Economy and Competitiveness of Spain/FDER Program of EU (MAT2017-87579-R and MAT2017-84228-R Projects), the University Institute of Research on Electron Microscopy and Materials (IMEYMAT) of Cadiz University (HOMOGREEN and NUPRECAT Projects) and the Junta de Andalucía (FQM-110 group)., Número de páginas: 11
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Artículo científico (JournalArticle)

Alkoxysilane-based consolidation treatments: Laboratory and 3-years In-Situ assessment tests on biocalcarenite stone from Roman Theatre (Cadiz)

  • Gemelli, Giada María Chiara
  • Zarzuela Sánchez, Rafael
  • Alarcón-Castellano, Francisco
  • Mosquera Díaz, María Jesús
  • Gil Montero, María Luisa Almoraima
This manuscript presents a 1 year in the laboratory and 3 years In-Situ evaluation of an alkoxysilane-based consolidant containing SiO2 nanoparticles (SiO2NPs) on Ostionera stone, a biocalcarenite traditionally employed in Southwestern Spain. C ' adiz Roman Theatre was selected for In-Situ application and testing. In order to safeguard the theatre, preliminary laboratory experiments were carried out. Firstly, the compatibility and the effectiveness of the consolidant product were evaluated in the laboratory, demonstrating that the incorporation of SiO2NPs improves drying time and consolidant effect. Subsequently, the consolidant was applied In-Situ and the long-term performance was monitored over 3 years through non-destructive tests. The treatment exhibit moderate incompatibility degree (6.1) and demonstrating the long-lasting performance of the SiO2NPs-based consolidant treatment., 1 This work has been supported by the Spanish Government MAT2017-84228-R (MINECO/AEI//FEDER,UE) and PID2020-115843RB-I00/AEI/10.13039/501100011033. This work been cofinanced by the European Union under the 2014-2020 ERDF Operational Programme and by the Department of Economic Transformation, Industry, Knowledge, and Universities of the Regional Government of Andalusia. Project reference: FEDER-UCA18-106613. Giada M.C. Gemelli would also like to thank the Spanish Government for her predoctoral grants (PRE2018-085799). We thank the Cadiz Roman Theatre staff and Manuel Luna for their collaboration.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Artículo científico (JournalArticle)

Consolidation of artificial decayed portland cement mortars with an alkoxysilane-based impregnation treatment and its influence on mineralogy and pore structure

  • Garcia-Lodeiro, Inés
  • Zarzuela Sánchez, Rafael
  • Mosquera Díaz, María Jesús
  • Blanco-Varela, María Teresa
Surface treatments, especially hydrophobic agents to prevent water ingress and consolidants able to fill decay- induced cracks, are often proposed as a method for preserving stone cultural heritage, however its use to pro- tect concrete heritage is much less common. New products, specifically designed for concrete, have been developed. These products are based on alkoxysilanes that interact directly with the products of portland cement (OPC) hydration (essentially Ca(OH)2 and C-S-H) to generate additional C-S-H gel. This study assesses the effect of an impregnation treatment, based on alkosysilanes, on artificially decayed cement mortars, in terms of product penetration depth, changes in the porosity of mortars and changes in its mechanical strengths. Reduced porosity and enhanced mechanical strength attested to treatment efficacy. Substrate porosity and pore size distribution were not the only factors found to condition treatment effectiveness, however, mineralogical changes caused by the deterioration processes (such as the presence or absence of portlandite, or the presence of salts) modify the sol gelling time and the substrate surface energy, impacting treatment penetration depth.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Artículo científico (JournalArticle)

Development of a novel engineered stone containing a CuO/SiO2 nanocomposite matrix with biocidal properties

  • Zarzuela Sánchez, Rafael
  • Gil Montero, María Luisa Almoraima
  • Carretero, Jesús
  • Carbú Espinosa de los Monteros, María
  • Cantoral Fernández, Jesús Manuel
  • Mosquera Díaz, María Jesús
Building materials decay is caused by the combination of chemical, physical and biological aspects. Therefore, the development of innovative multifunctional building materials is an alternative to reduce their impact. This can be achieved by post-treatments or by direct changes in the fabrication of synthetic materials, such as engineered stone. The aim of this work is to develop a new type of engineered stone by using a CuO/SiO2 nanocomposite matrix, synthetized via sol–gel, as a binder and quartz particles of different grain size as aggregate. The use of a sol–gel route allows creating an amorphous SiO2 structure chemically compatible with the quartz aggregates, while CuO nanoparticles are added for their biocidal properties. The new materials present anti-fungal properties against yeast and Aspergillus carbonarius spores, a high surface hardness, thermal resistance and an appropriate impact resistance for their use in flooring and claddings, although their mechanical strength is overall lower than a resin-matrix engineered stone. The proportion of CuO in the matrix and water content modify the sol–gel kinetics and quartz sedimentation, which have an impact on the structure and mechanical properties.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Artículo científico (JournalArticle)

Anti-fouling nano-Ag/SiO2 ormosil treatments for building materials: The role of cell-surface interactions on toxicity and bioreceptivity

  • Domínguez, Marcia
  • Zarzuela Sánchez, Rafael
  • Moreno-Garrido, Ignacio
  • Carbú Espinosa de los Monteros, María
  • Cantoral Fernández, Jesús Manuel
  • Mosquera Díaz, María Jesús
  • Gil Montero, María Luisa Almoraima
Protective coatings with hydrophobic or biocide properties are commonly employed to prevent biofouling of building materials exposed to the environment. Although the factors affecting bioreceptivity of the base materials are well known, the influence of the coating and/or biocide agent surface properties on the interaction with the cell surface is often overlooked. As such, a proper understanding of these interfacial interactions can help improve their anti-fouling effectiveness. This work studies a multifunctional superhydrophobic/biocide treatment, containing surface engineered Ag/SiO2 nanoparticles embedded in an organically modified silica matrix, focusing on determining the effect of the cell-nanoparticle interactions and surface properties on its effectiveness against algal fouling. The modification of SiO2 with positively charged groups increased the interaction of the biocide with the cell walls through electrostatic forces, while at the same time it promotes cell aggregation. The hydrophobic matrix decreases initial colonization due to its lower roughness and water absorption, although surface free energy measurements indicated an increase of the cell-surface adhesion force as polarity of the cell wall decreased. A Cassie-Baxter wetting regime on the superhydrophobic surfaces decreased effective contact area and adhesion force, though this state was quickly lost under exposure to the cultures
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Artículo científico (JournalArticle)

Chemistry of the interaction between an alkoxysilane-based impregnation treatment and cementitious phases

  • Garcia-Lodeiro, Inés
  • Carmona-Quiroga, P.M.
  • Zarzuela Sánchez, Rafael
  • Mosquera Díaz, María Jesús
  • Blanco-Varela, María Teresa
Chemical compatibility with a wide range of materials is among the features that has driven the use of alkoxysilanes as consolidants in built structures. Such compatibility is particularly important in cementitious materials where the reaction with portlandite may generate C-S-H gel, one of the main hydration phases of OPC. The cementitious matrix is a complex system, however, and the reaction of its many phases with alkoxysilanes, while poorly understood, may determine treatment efficacy. This article describes a detailed study of the individual interactions between an oligomeric alkoxysilane-based impregnation treatment previously shown to interact with the portlandite present in cement paste and the cementitious phases generated in ordinary portland cement hydration. The findings show that both portlandite and C-S-H gel interact with the silicon oligomers in the hydrolysed impregnation treatment to generate a C-S-H gel (in the case of portlandite) and a rise in C-S-H gel mean chain length (MCL). Ettringite is also altered in the presence of alkoxysilanes, transforming to gypsum and AH(3). Its transformation generates a tetrahedral aluminium that is taken up into a high silicon gel sourced from the treatment to form an amorphous aluminosilicate gel. Monocarboaluminate and katoite also partially decompose in the interaction with the product, whereas gibbsite remains unaffected.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Tesis doctoral (DoctoralThesis)

Evaluación de la compatibilidad, eficacia y durabilidad de nanomateriales innovadores para la protección y consolidación de monumentos y edificios históricos

  • Gemelli, Giada María Chiara
El punto de partida de este trabajo ha sido, como el propio título indica, “la evaluación de la compatibilidad, eficacia y durabilidad de diferentes tratamientos para la protección y consolidación de monumentos y edificios históricos”. Esta investigación se centra en el estudio de los monumentos y de los factores de degradación que afectan los materiales de construcción, por un lado, y, por otro, en la búsqueda de tratamientos de conservación capaces de ralentizar el proceso de degradación y prolongar su vida útil para transmitirlo a las generaciones futuras lo más cerca posible de la forma en que lo heredamos del pasado. Para lograr este objetivo, se realizó preliminarmente un estudio completo de la litología, las características químico-físicas y mecánicas de los materiales de construcción utilizados para su construcción. Además, se llevó a cabo un estudio sobre el entorno ambiental seguido de la identificación de los procesos de degradación que afectan al monumento. De acuerdo con el punto de partida, se seleccionaron varios productos de conservación, previamente sintetizados por el Grupo TEP-243, y se evaluaron en condiciones de laboratorio sobre los materiales de construcción utilizados en los monumentos, para comprobar su efectividad y compatibilidad. Finalmente, los productos más adecuados se aplicaron sobre los monumentos a fin de evaluar su efectividad a lo largo del tiempo.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Artículo científico (JournalArticle)

Ormosils loaded with SiO2 nanoparticles functionalized with Ag as multifunctional superhydrophobic/biocidal/consolidant treatments for buildings conservation

  • Zarzuela Sánchez, Rafael
  • Carbú Espinosa de los Monteros, María
  • Gil Montero, María Luisa Almoraima
  • Cantoral Fernández, Jesús Manuel
  • Mosquera Díaz, María Jesús
The alarming increase of pollution has significantly increased buildings maintenance. Nowadays, the economic figures associated to repairing activities are even more relevant than those corresponding to new construction works, especially on heritage buildings. Since the degradation of building materials is the result of a complex combination of physical, chemical and biological agents, the development of multifunctional protective treatments remains a significant challenge. We report a simple strategy to produce a versatile biocidal/superhydrophobic/consolidant treatment by incorporating biocidal Ag nanoparticles (AgNPs) grafted to functionalized SiO2NPs into a silica sol, which can be applied by simple procedures such as spraying. The use of an Ag-SiO2 coupling agent increases biocidal effectiveness up to >90% values due to: (1) an increase of the AgNPs stability; (2) a hierarchical roughness due to the formation of Ag/SiO2NPs clusters; and (3) an enhanced contact with the cell walls. In addition, the synergistic effect allows for an easier removal of the dead cells, increasing the durability of the treatment.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Producing C-S-H gel by reaction between silica oligomers and portlandite: A promising approach to repair cementitious materials

  • Zarzuela, Rafael
  • Luna, Manuel
  • Carrascosa, Luis M.
  • Yeste, María Pilar
  • García-Lodeiro, Inés
  • Blanco-Varela, María Teresa
  • Cauqui, Miguel A.
  • Rodríguez-Izquierdo, José M.
  • Mosquera, Maria Jesus
Impregnation treatments are one of the alternatives to protect concrete-based building and monuments from weathering degradation. However, it is important to consider the chemical compatibility of the reaction products with the building material. The impregnation product studied here consists of a silica oligomer able to polymerize, by a simple sol-gel process, inside the pore structure of concrete. In this work, we investigate the ability of this impregnation treatment to produce C-S-H gel in contact with cement paste. A complete characterization of the reaction products demonstrated that the silanol groups from silica oligomers react with the portlandite present in the cement paste generating a material with the chemical, structural and morphological features of C-S-H gel. Simultaneously, the 29Si NMR results indicate that the Sisingle bondO units are incorporated into the existing C-S-H, increasing its chain length. These results open the way for a simple concrete structures repairing procedure., This project has received funding from the European Union's Horizon 2020 - Research and Innovation Framework Programme under grant agreement No 760858; and from Spanish Government/FEDER-EU under research project MAT2017-84228-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

4-Year in-situ assessment of a photocatalytic TiO2/SiO2 antifouling treatment for historic mortar in a coastal city

  • Gemelli, Giada M. C.
  • Luna, Manuel
  • Zarzuela, Rafael
  • Almoraima Gil, M. L.
  • Carbú, María
  • Moreno-Garrido, Ignacio
  • Mosquera, María J.
This manuscript presents a 4 years in-situ evaluation of TiO2/SiO2-based product applied to a mortar seating belonging to the bleachers of the Cadiz Roman Theatre, affected by biofouling and organic deposits. Antifouling performance was studied by colorimetric measurements and ATP analyses. Surface sampling was performed for biofouling identification, being remarkable the presence of filamentous fungi and cyanobacteria. Additionally, antifouling performance was checked during a 4 years in-situ monitoring study. SEM observations, carried out 4 years after the product application, demonstrate that the TiO2 integration in a SiO2 matrix produces a durable coating which allows for prolongation of the antifouling performance over time. According to the results obtained, 4 years after the application of the treatment, the treated area still maintains its antifouling efficacy, exhibiting a 40% reduction in organic deposit and 61% inhibition of biological growth compared to the untreated area. The results of this study show that the application of the SiO2/TiO2-based product may potentially reduce the costs of cleaning and maintenance works. At the same time, it is considered that the antifouling efficacy is more pronounced during the first two years and could be taken into account in the maintenance and re-application actions., This work has been supported by the Spanish Government MAT2017-84228-R (MINECO/AEI//FEDER, UE) and PID2020- 115843RB-I00/AEI/10.13039/501100011033. This work has been co-financed by the European Union under the 2014–2020 ERDF Operational Programme and by the Department of Economic Transformation, Industry, Knowledge, and Universities of the Regional Government of Andalusia. Project reference: FEDER-UCA18-106613. Giada M.C. Gemelli would also like to thank the Spanish Government for her pre-doctoral grants (PRE2018-085799). M. Luna would also like to thank the Spanish Government for his Margarita Salas grant (2021-067/PN/MS-RECUAL/CD) supported by the European Union-NextGenerationEU., Peer reviewed