Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Cold sintering process of ZnO ceramics: Effect of the nanoparticle/microparticle ratio

  • Serrano Rubio, Aída
  • Caballero-Calero, Olga
  • García García-Tuñón, Miguel Ángel
  • Lazić, Snežana
  • Carmona, N.
  • Castro, Germán R.
  • Martín-González, Marisol
  • Fernández Lozano, José Francisco
We show the efficiency in the preparation of >95 % dense ZnO ceramics by cold sintering process through the incorporation of ZnO nanoparticles in the 1−10 wt% range at temperatures of 170 °C, pressures of 750 MPa and a pellet height/diameter ratio of 0.38. Morphological, structural and physical properties are dependent on the amount of ZnO nanoparticles incorporated into the system. After the densification by cold sintering process, ZnO ceramics show a reduction of the average valence indicating the deficiency of oxygen, similar to ceramics sintered by the conventional route. Besides, the generation of structural disorder and modifications into the ZnO lattice are identified in sintered ceramics, inducing intrinsic defects related to the loss of oxygen ions, the diffusion of zinc and zinc vacancies, which depend on the sintering process and the starting powders. These characteristics influence the final functional properties of the sintered ZnO ceramics, such as the visible photoluminescence signal., This work has been supported by the Ministerio Español de Ciencia, Innovación y Universidades (MCIU) through the projects MAT2017-86540-C4-1-R, MAT2017-86540-C4-3-R and RTI2018-095303-A-C52. The European Synchrotron (ESRF), MCIU and Consejo Superior de Investigaciones Cientificas (CSIC) are acknowledged for the provision of synchrotron radiation facilities. We also thank the BM25-SpLine staff for the technical support beyond their duties. A.S. acknowledges financial support from the Comunidad de Madrid for an “Atracción de Talento Investigador” contract (No. 2017-t2/IND5395).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

CoSb3-based skutterudite nanocomposites prepared by cold sintering process with enhanced thermoelectric properties

  • Serrano Rubio, Aída
  • Caballero-Calero, Olga
  • Granados-Miralles, Cecilia
  • Gorni, Giulio
  • Manzano, Cristina V.
  • Rull Bravo, Marta
  • Moure Arroyo, Alberto
  • Martín-González, Marisol
  • Fernández Lozano, José Francisco
[EN] We show here for the first time the use of a cold sintering process (CSP) to sinter CoSb-based thermoelectric materials. CSP at 150 °C for 90 min under a uniaxial pressure of 750 MPa yields pieces with a relative density of 86 %, which is increased to around 92 % after a post-annealing at temperatures ≥ 500 °C in Ar atmosphere. The reported CSP produces Te doped-CoSb nanocomposites with similar morphological and structural characteristics to the starting nanopowders obtained by ball milling in air atmosphere. The post-thermal treatment induces grain coalescence and grain growth, crystallite size growth as well as compositional changes in the nanocomposite, decreasing the amount of the main phase, CoSb, and increasing the weight of secondary phase, CoSb, up to a 30 wt% at 600 °C. Remarkably, the average valence for the Co, Sb and Te absorbing atoms is neither transformed by the sintering process nor by the subsequent heat treatment. The functional response of the sintered thermoelectric nanocomposites exhibits a maximum figure of merit of 0.12(3) at room temperature for the nanocomposites sintered by CSP with a subsequent post-annealing at 500 °C. This is mainly due to its low thermal conductivity in comparison with similar powders sintered by other approaches, and it is explained by the morphological and structural properties. These findings represent an attractive alternative for obtaining efficient thermoelectric skutterudites by a scalable and cost-effective route., This work has been supported by the Ministerio Español de Ciencia e Innovación (MICINN) through the projects MAT2017-86540-C4-1-R, MAT2017-86540-C4-3-R, RTI2018-095303-A-C52, PID2020-114192RB-C41 and PID2020-118430GB-100. Part of these experiments were performed at the CLAESS-BL22 beamline at ALBA Synchrotron (Grant no. 2020094658) and in collaboration with ALBA staff. A.S. and C.V.M. acknowledge financial support from the Comunidad de Madrid for an “Atracción de Talento Investigador” Contract no. 2017-t2/IND5395 and 2019-t1/IND-13541, respectively. C.G.-M. acknowledges financial support from MICINN through the “Juan de la Cierva” program (FJC2018-035532-I). A.M. is indebted to MICINN for the “Ramón y Cajal” contract (RYC-2013-14436), which is co-financed with European Social Fund., Peer reviewed