Skip to main content

AJUSTE DE LAS PROPIEDADES CATALITICAS EN ELECTRODOS PARA CELDAS PROTONICAS ELECTROQUIMICAS

PCI2019-103742

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos Programación Conjunta Internacional
Call year 2019
State Plan 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Tailoring oxide nanoparticle exsolution in La0.5Ba0.5-yCo1-xFexO3-[delta]

  • Balcerzak, Daria
  • Norby, Truls
  • Strandbakke, Ragnar
  • Gazda, Maria
  • Wachowski, Sebastian L.
  • López-García, Andrés
  • Carrillo-Del Teso, Alfonso Juan
  • Balaguer Ramirez, Maria|||0000-0002-7098-9235
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] We show that oxide nanoparticles (NPs) exsolve on La0.5Ba0.5-yCo1-xFexO3-¿ (x = 0-1, y = 0 or 0.01) in oxidizing conditions. The phenomenon occurs only in Co-containing materials and depends on pO2 and pH2O pressures. Under dry conditions, the smallest NPs average about 30 nm, with 200-300 NPs/mu m2 at pO2= 5 x 10-5 atm. For pO2= 1 atm, NP size increases to 100-200 nm, and population drops to a few to about 20 NPs/mu m2 depending on A-site nonstoichiometry and x. In humid conditions, the smallest NPs around 50 nm, with a peak of 100 NPs/mu m2 exsolve for pO2= 1. Transmission electron microscopy shows that exsolved NPs in La0.5Ba0.5-yCoO3-¿ are Ba-Orich. We propose defect chemistry models, indicating that exsolution is driven by oxidation reactions forming A-site vacancies, increasing exsolved material with higher pO2. We suggest that adsorbed water under humid conditions blocks nucleation sites, altering observed trends., Project FunKeyCat is supported by the National Science Centre, Poland, The Research Council of Norway (FunKeyCat 299736) , and the Spanish Government (PCI2019-103742, RYC2021-033889-I) under the M-ERA.NET 2, which has received funding from the European Union's Horizon 2020 research and innovation program under grant agreement no 685451. We thank the support of the Electronic Microscopy Service of the Universitat Politècnica de València.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Evaluating oxide nanoparticle exsolution on A-site deficient PrBaCo 2 O 6-o electrodes

  • Carrillo-Del Teso, Alfonso Juan
  • Balaguer Ramirez, Maria|||0000-0002-7098-9235
  • López-García, Andrés
  • Fabuel Robledo, Maria
  • Delgado-Galicia, Blanca|||0009-0004-4655-5789
  • Isabelle Rodriguez|||0000-0001-5479-2494
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
  • Solis, Cecilia
  • Haas, Sylvio
  • Vøllestad, Einar
  • Wachowski, Sebastian
  • Strandbakke, Ragnar
  • Norby, Truls
[EN] Nanoparticle exsolution is a powerful technique for functionalizing redox oxides in energy applications, particularly at high temperatures. It shows promise for solid oxide fuel cells and electrolyzers. However, exsolution of other chemistries like metal oxides is not well studied, and the mechanism is poorly understood. This work explores oxide exsolution in PrBa1¿xCo2O6¿¿ (x = 0, 0.05, 0.1, 0.15) double perovskites, practiced electrodes in proton ceramic fuel cells and electrolyzers. Oxide exsolution in PrBa1¿xCo2O6¿¿ aimed at boosting the electrocatalytic activity and was evaluated by varying intrinsic materials-related properties, viz. A-site deficiency and external parameters (temperature, under fixed time, and pO2 = 10¿5 atm conditions). The materials were analyzed with conventional characterization tools and synchrotron-based small-angle x-ray scattering. Unlike metal-nanoparticle exsolution, increasing the A-site deficiency did not enhance the extent of oxide-nanoparticle exsolution, whereas larger nanoparticles were obtained by increasing the exsolution temperature. Combined Raman spectroscopy and electron microscopy analysis revealed that BaCoO3, Co3O4, and amorphous BaCO3 nanoparticles were formed on the surface of the double perovskites after the reductive treatments. The present results demonstrate the complexity of oxide-nanoparticle exsolution in comparison with metal-nanoparticle exsolution. Further materials screening and mechanistic studies are needed to enhance our understanding of this method for functionalizing proton ceramic electrochemical cells (PCEC) electrodes., We acknowledge the Spanish Government through the M-ERA.NET Joint Call 2018 'FunKeyCat' (PCI2019-103742, RYC2021-033889-I), the Research Council of Norway (Grant No. 299736), and the National Science Centre Poland, which has received funding from the European Union's Horizon 2020 research and innovation program under Grant Agreement No. 685451. We thank the support of the Electronic Microscopy Service of the Universitat Politecnica de Valencia and the Norwegian Center for Transmission Electron Microscopy (NORTEM) (No. 197405/F50). The authors acknowledge DESY (Hamburg, Germany), a member of the Helmholtz Association HGF, for providing experimental facilities. SAXS-WAXS measurements were carried out at PETRA III (beamtime allocated for proposals I-20210219 and I-20210223), and the authors would like to thank Andre Conceicao for assistance in using the SAXSMAT beamline P62.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Additive manufacturing of Proton-Conducting Ceramics by robocasting with integrated laser postprocessing

  • Pospiech, Joanna
  • Nadolska, Malgorzata
  • Cieslik, Mateusz
  • Sobczyk, Tomasz
  • Chmielewski, Marek
  • Mielewczyk-Gryn, Aleksandra
  • Strandbakke, Ragnar
  • Wachowski, Sebastian Lech
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] A hybrid system combining robocasting and NIR laser postprocessing has been designed to fabricate layers of mixed proton-electron conducting Ba0.5La0.5Co1-xFexO3-delta ceramic. The proposed manufacturing technique allows for the control of the geometry and microstructure and shortens the fabrication time to a range of a few minutes. Using 5 W laser power and a scanning speed of 500 mm<middle dot>s(-1), sintering of a round-shaped layer with an 8 mm radius was performed in less than 2 s. The single phase of the final product was confirmed by X-ray diffraction. Various ceramic-to-polymer weight ratios were tested, showing that various porosities of microstructures of similar to 30 - 35 % and similar to 19 % can be obtained with 2:1 and 4:1 loading respectively., The project FunKeyCat is supported by the National Science Centre, Poland under the M-ERA.NET 2, which has received funding from the European Union's Horizon 2020 research and innovation program under Grant Agreement No 685451, from the Research Council of Norway (Grant n degrees 299736) , and the Spanish Government (M-ERA.NET PCI2019-103742) . The authors also express gratitude to Piotr Okoczuk, MSc Eng, for performing the confocal microscopy measurements and to Robert Tylingo, Ph.D., D.Sc. Eng., for conducting the viscosity measurements and for their contribution to this work.