Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 14
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Development and validation of a calibration gauge for length measurement systems

  • Brosed, Francisco Javier
  • Acero Cacho, Raquel
  • Aguado, Sergio
  • Herrer, Marta
  • Aguilar, Juan José
  • Santolaria Mazo, Jorge
Due to accuracy requirements, robots and machine-tools need to be periodically verified and calibrated through associated verification systems that sometimes use extensible guidance systems. This work presents the development of a reference artefact to evaluate the performance characteristics of different extensible precision guidance systems applicable to robot and machine tool verification. To this end, we present the design, modeling, manufacture and experimental validation of a reference artefact to evaluate the behavior of these extensible guidance systems. The system should be compatible with customized designed guides, as well as with commercial and existing telescopic guidance systems. Different design proposals are evaluated with finite element analysis, and two final prototypes are experimentally tested assuring that the design performs the expected function. An estimation of the uncertainty of the reference artefact is evaluated with a Monte Carlo simulation.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

2D positioning control system for the planar motion of a nanopositioning platform

  • Díaz-Pérez, Lucía
  • Torralba, Marta
  • Albajez, José Antonio
  • Yagüe-Fabra, José Antonio
A novel nanopositioning platform (referred as NanoPla) in development has been designed to achieve nanometre resolution in a large working range of 50 mm × 50 mm. Two-dimensional (2D) movement is performed by four custom-made Halbach linear motors, and a 2D laser system provides positioning feedback, while the moving part of the platform is levitating and unguided. For control hardware, this work proposes the use of a commercial generic solution, in contrast to other systems where the control hardware and software are specifically designed for that purpose. In a previous paper based on this research, the control system of one linear motor implemented in selected commercial hardware was presented. In this study, the developed control system is extended to the four motors of the nanopositioning platform to generate 2D planar movement in the whole working range of the nanopositioning platform. In addition, the positioning uncertainty of the control system is assessed. The obtained results satisfy the working requirements of the NanoPla, achieving a positioning uncertainty of ±0.5 µm along the whole working range.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Design and development of a calibration artefact for length measurement system

  • Brosed Dueso, Francisco Javier
  • Acero Cacho, Raquel
  • Aguado Jiménez, Sergio
  • Herrer Torres, Marta
  • Aguilar Martín, Juan José
  • Santolaria Mazo, Jorge
Due to accuracy requirements, robots and machine-tools need to be periodically verified and calibrated through associated verification systems that sometimes use extensible guidance systems. This work presents a reference artefact to evaluate the performance characteristics of different extensible precision guidance systems applicable to robot and machine tool verification. To this end, we present the design, modeling, manufacture and experimental validation of a reference artefact to evaluate the behavior of these extensible guidance systems. The system should be compatible with customized designed guides, as well as with commercial and existing telescopic guidance systems. An estimation of the uncertainty of the reference artefact is evaluated with a Monte Carlo simulation.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Configuration optimisation of laser tracker location on verification process

  • Aguado, Sergio
  • Pérez, Pablo
  • Albajez, José Antonio
  • Santolaria, Jorge
  • Velázquez, Jesús
Machine tools are verified and compensated periodically to improve accuracy. The main aim of machine tool verification is to reduce the influence of quasi-static errors, especially geometric errors. As these errors show systematic behavior, their influence can be compensated. However, verification itself is influenced by random uncertainty sources that are usually not considered but affect the results. Within these uncertainty sources, laser tracker measurement noise is a random error that should not be ignored and can be reduced through adequate location of the equipment. This paper presents an algorithm able to analyse the influence of laser tracker location based on nonlinear optimisation, taking into consideration its specifications and machine tool characteristics. The developed algorithm uses the Monte Carlo method to provide a zone around the machine tool where the measurement system should be located in order to improve verification results. To achieve this aim, different parameters were defined, such as the number of tests carried out, and the number and distribution of points, and their influence on the error due to the laser tracker location analysed.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Positioning uncertainty of the control system for the planar motion of a nanopositioning platform

  • Díaz-Pérez, Lucía
  • Torralba, Marta
  • Albajez, José Antonio
  • Yagüe Fabra, José Antonio
The novel nanopositioning platform (NanoPla) that is in development at the University of Zaragoza has been designed to achieve nanometre resolution in a large working range of 50 mm × 50 mm. The 2D movement is performed by four custom-made Halbach linear motors and a 2D laser system provides positioning feedback, while the moving part of the platform is levitating and unguided. As control hardware, this work proposes the use of a commercial solution, in contrast to other systems, where the control hardware and software were specifically designed for the purpose. In a previous work of this research, the control system of one linear motor implemented in the selected commercial hardware was presented. In this study, the developed control system is extended to the four motors of the nanopositioning platform to generate a 2D planar movement in the whole working range of the nanopositioning platform. In addition, the positioning uncertainty of the control system is assessed. The obtained results satisfy the working requirements of the NanoPla, achieving a positioning uncertainty of ±0.5 µm along the whole working range.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Algorithm to optimize measurement system location in a machine tool verification

  • Aguado, Sergio
  • Pérez, Pablo
  • Albajez, José Antonio
  • Santolaria, Jorge
  • Velázquez, Jesús
Nowadays, machine tool accuracy is a competitive element. To improve it, machine tools are verified and compensate periodically reducing the influence of their geometric errors. As geometric errors have systematic behavior, their influence can be compensated after verification. However, verification itself is influenced by random uncertainty sources that affect verification results. Within all influences on machine tool volumetric verification, laser tracker measurement noise is a random uncertainty source that is not usually considered. However, it should not be ignored and can be reduced through an adequate location. This paper presents an algorithm able to analyze the influence of laser tracker location, taking into consideration its specifications and machine tool characteristics. To do that, the developed algorithm provides a zone around MT to locate the measurement system using the Monte Carlo Method. Moreover, it provides the probability distribution function of laser tracker influence related to LT location zone. Therefore, if MT is used as a traceable measurement system, its uncertainty cannot be smaller than LT location uncertainty.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Development of a high precision telescopic instrument based on simultaneous laser multilateration for machine tool volumetric verification

  • Aguilar, Juan José
  • Acero, Raquel
  • Brosed, Francisco Javier
  • Santolaria, Jprge
This paper presents the design of a high precision telescopic system consisting in three lines, with measuring principle based on simultaneous laser multilateration. The system offers the high precision of the interferometer systems and allows the autonomous tracking of a sphere joined to the spindle nose of the machine tool by simultaneous contact of all the lines. The main advantage of the system is that it allows data capture to be carried out in a single cycle thanks to simultaneous operation with at least three telescopic arms using a novel multipoint kinematic coupling. This results in a significant reduction of the time taken for data capture and improves measurement accuracy due to avoiding the effect of temperature variations between cycles and machine tool repeatability. The work explains the working principle of the system, its main components, and the design parameters considered for the development of the system. The system is simple to operate, compact, agile, and suitable for the verification of small-or medium-sized machine tools with linear and/or rotary axes.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Study on Machine Tool Positioning Uncertainty Due to Volumetric Verification

  • Aguado, Sergio
  • Pérez, Pablo
  • Albajez, A. José
  • Santolaria, Jorge
  • Velazquez, Jesús
Volumetric verification is based on the machine tool (MT) kinematic model, along with its geometric errors. Although users often ignore the uncertainty of verification, the use of the MT as a traceable measurement system in the manufacturing process has increased the need for professionals to be aware of it. This paper presents an improvement in the MT kinematic model, introducing in it the influence of verification uncertainty sources. These sources have been classified into four groups: the MT, the measurement system itself, the measurement strategy, and the optimization strategy. As the developed model exhibits non-linear behavior, the Monte Carlo method was used to determine the influence of the measurement system on verification uncertainty using synthetic tests. In this manner, an improved estimation of the MT uncertainty can be obtained. Therefore, if the MT is used as a traceable measurement system, its accuracy should not be higher than the laser tracker (LT) verification influence. It hence shows the importance of LT influence.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Effect of ambient temperature on machine tool compensation functions

  • Aguado, S.
  • Pérez, P.
  • Albajez, J. A.
  • Velázquez, J.
  • Santolaria, J.
Volumetric verification is increasing daily its relevance. However, as it is based on mathematical compensation, it does not model only the influence of the machine tool's geometric error to verify, but the total error of the data. Among all error sources, thermal variations due to changes in environmental conditions strongly affect MT position accuracy. This paper studies how verification changes affect compensation functions based on a modification of machine tool kinematic model and a generator of synthetic data. It takes into consideration the influence of the measurement noise on verification too. Moreover, the paper also studies how differences between verification and working conditions affect the accuracy of MT compensation functions. To do that, a brief explanation of the developed algorithm is presented.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Influence of high precision telescopic instrument characterization on multilateration points accuracy

  • Aguado, S.
  • Brosed, F. J.
  • Acero, R.
  • Aguilar, J. J.
  • Santolaria, J.
  • Pueo, M.
Currently accuracy of manufacturing machines is a must. Verification is the main way to obtain it; highlighting the volumetric verification as the best technique to improve machine tool position accuracy along all its workspace in the shortest time possible. In this way, different measurements based on multilateration techniques like laser tracker and laser tracer are used. This paper studies how characteristics of a new high precision telescopic system consisting in three lines, with measuring principle based on simultaneous laser affect multilateration accuracy to obtain 3D coordinates. The paper analyses instrument characterising both the design, the components and their operation. Moreover, tests carried out study how instruments behavior affect to the accuracy of data capture using analytical and optimization techniques, proving an error estimation depending on the technique used.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Calibration and uncertainty budget analysis of a high precision telescopic instrument for simultaneous laser multilateration

  • Javier Brosed, F.
  • José Aguilar, J.
  • Acero, R.
  • Santolaria, J.
  • Aguado, S.
  • Pueo, M.
The precision manufacturing industry depends on precision measurement instruments capable of tracing the measurement results to national and international standards. This paper presents a calibration model for a high precision telescopic instrument (HPTI) for machine tool verification together with its estimated uncertainty budget. The instrument tracks autonomously a target using an interferometric sensor to measure distances and allows the simultaneous use of three HPTIs for multilateration, decreasing data capture time and improving measurement accuracy. A calibrating ball beam artefact, previously calibrated with a coordinate measurement machine, is used to trace the calibration results. The uncertainty of the HPTI is estimated in laboratory conditions. The uncertainty budget of the HPTI, as well as the uncertainty of simultaneous multilateration, in workshop conditions are analysed and estimated with Monte Carlo. The calibration model defined gives traceability to the measurement results obtained with the HPTI allowing its use in machine tool verification processes. © 2022 The Author(s)
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Evaluation of a telescopic simultaneous ballbar in a 3-axis machine tool using a reference equipment

  • Acero, Raquel
  • Brosed, Francisco Javier
  • Pueo, Marcos
  • Aguado, Sergio
  • Aguilar, Juan José
  • Velázquez, Jesús
This paper outlines the evaluation methodology for a Telescopic Simultaneous Ballbar (TSB) developed for distance measurement using an interferometer as a reference equipment. The procedure is executed in a 3-axis machine tool, one of the final applications of the TSB that is machine tool volumetric verification. Two distinct evaluation techniques are devised, with the new virtual line approach enabling an assessment of the TSB's performance within an extended verification volume and requiring only a single alignment position for the interferometer. The measurement repeatability of the equipment is assessed and its measurement uncertainty is estimated in workshop conditions. The results reveal the flexibility of the TSB measurement process similar to that of a laser tracker and the degree of measurement accuracy, which shows values comparable to the interferometer. Consequently, the TSB could facilitate faster and more accurate machine tool verification and calibration compared to existing systems.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Thermal error compensation strategy in simultaneous laser multilateration for volumetric verification

  • Brosed Dueso, Francisco Javier
  • Aguilar Martín, Juan José
  • Acero Cacho, Raquel
  • Santolaria Mazo, Jorge
  • Aguado Jiménez, Sergio
  • Pueo Arteta, Marcos
Verification systems are needed for periodic verification and calibration of robots and machine tools to maintain and increase their accuracy. One of the ways to verify the volumetric accuracy of a manufacturing system is to measure the position of its head (X, Y, Z coordinates) using measurement systems that provide these results with the appropriate precision. The laser interferometer provides results with accuracy levels suitable for robot and machine tool verification applications. However, to measure the head position of manufacturing systems (X, Y, Z coordinates), the use of laser interferometers requires a prior adjustment to a reference length, since they measure incrementally. This adjustment procedure of the measurement system introduces an error in the resulting head coordinates that depends on the environmental conditions and the material of the standard element used to materialize the reference length. This paper analyzes the temperature effect in the adjustment process and how temperature errors introduced in said process affect the head 3D coordinates calculation of the Manufacturing System under inspection.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Surface roughness prediction in turning processes for grey cast iron: A hybrid machine learning approach integrating infrared thermography

  • Aguado, Sergio
  • Pueo, Marcos
  • Acero, Raquel
  • Majarena, Ana Cristina
  • Santolaria, Jorge
Workpiece surface quality is a critical control parameter in machining processes, influencing functional performance, dimensional precision, and wear resistance. However, accurately predicting surface roughness is complex, often limited by the computational demands of traditional high-precision methods and the reliance of existing models solely on cutting parameters, hindering real-time monitoring. This research introduces a hybrid Artificial Neural Network (ANN) methodology specifically developed for predicting surface roughness of grey cast iron GG-25 workpieces machined in turning processes, a material previously unstudied in this context. The methodology integrates real-time infrared thermal measurements from multiple defined regions of interest (ROIs) within the tool-workpiece contact zone, along with cutting parameters. Experimental results demonstrated that feed rate (f) is the most significant cutting parameter (effect = 0.43) affecting surface quality, followed by its combination with cutting speed (Vc) (effect = −0.25) and cutting speed (effect = 0.18). Correlation and non-linear regression analyses revealed complex, often exponential relationships between temperature and surface roughness, showing temperature an upward trend as machining progressed. The developed ANN achieves a correlation coefficient (R) value of 0.99 both when predicting the roughness arithmetic mean deviation (Ra) parameter in training conditions and when using data from experiments not used in training (validations data). Moreover, the model reaches a correlation coefficient value of 0.85 (test data) under cutting conditions different from those used in experiments, demonstrating robustness, significantly outperforming Support Vector Regression (SVR). This model represents a highly potential tool for real-time online inspection.