Skip to main content

REDUCCION DE CO2 EN EL TRANSPORTE MEDIANTE LA INYECCION DIRECTA DUAL-FUEL DE BIOCOMBUSTIBLES DE SEGUNDA GENERACION

TRA2017-87694-R

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2017
State Plan 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 35
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Analysis of a series hybrid vehicle concept that combines low temperature combustion and biofuels as power source

  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
[EN] This work evaluates the potential of a series hybrid vehicle concept that combines low temperature combustion (LTC) and biofuels as power source. To do this, experimental data from a previous work obtained in a singlecylinder engine running under ethanol-diesel dual-fuel combustion is used. Then, vehicle systems simulations are used to estimate performance and emissions of the LTC hybrid vehicle and compare them versus conventional diesel combustion (CDC). The vehicle selected to perform the simulations is the Opel Vectra, which equips the compression ignition engine used in the experimental tests. The results from the simulations used for the analysis are firstly optimized by combining design of experiments and the Kriging fitting method. The multi-objective optimization allows to determine some characteristics and controls of the hybrid vehicle. The comparison of the estimated performance and emissions of the LTC-hybrid concept versus CDC over the worldwide harmonized light vehicles test cycle (WLTC) and real driving cycle (RDE) revealed clear benefits in terms of energy consumption, CO2 and NOx and soot emissions. In this sense, the hybrid concept enabled a reduction of the final energy consumed of 3% in the RDE cycle and 6.5% in the WLTC as compared to CDC. In terms of engine-out emissions, the CO2 was reduced around 16% versus CDC, and engine-out NOx and soot were reduced below the levels imposed by the Euro 6 regulation. As a penalty, the engine-out HC and CO emissions increased to more than double than CDC. However, based on previous experimental results, it is expected that a conventional diesel oxidation catalyst can reduce the tail-pipe HC and CO levels below the Euro 6 limits., The authors gratefully acknowledge General Motors Global Research & Development for providing the engine used to acquire the experimental data shown in this investigation. The authors also acknowledge FEDER and Spanish Ministerio de Economía y Competitividad for partially supporting this research through TRANCO project (TRA2017- 87694-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Energy management strategies comparison for a parallel full hybrid electric vehicle using Reactivity Controlled Compression Ignition combustion

  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Carlucci, Paolo
  • Valletta, Andrea
  • Martínez-Boggio, Santiago Daniel
[EN] Reactivity Controlled Compression Ignition combustion technology potentials are well known for the capability to drastically reduce the engine-out nitrogen oxides and soot emissions simultaneously. Its implementation in mid-term low-duty diesel engines can be beneficial to meet the upcoming regulations. To explore the potential of this solution, experimental data are used from a compression ignition 1.9 L engine, which is operated under two combustion-modes: Reactivity Controlled Compression Ignition and conventional diesel combustion. Meanwhile, also the carbon dioxide emissions limitations must be fulfilled. To achieve this goal, the benefits associated to powertrain electrification in terms of fuel economy, can be joined with the benefits of RCCI combustion. To do so, two different supervisory control strategies are compared: Adaptive Equivalent Minimization Control Strategy and Rule-Based Control strategy, while dynamic programming is used to size the electric grid of the powertrain to provide the best optimal solution in terms of fuel economy and emissions abatement. The analysis of the designed hybrid powertrain is carried out numerically with GT-Suite and Matlab-Simulink software. The results show a great potential of the parallel full-hybrid electric vehicle powertrain equipped with the dual-mode engine to reduce the engine-out emissions, also to increase fuel economy with respect to the homologation fuel consumption of the baseline vehicle. The optimal supervisory control strategy was found to be the emissions-oriented Adaptive Equivalent Minimization Control Strategy, which scores a simultaneous reduction of 12% in fuel consumption, 75% in engine-out nitrogen oxides emissions and 82% in engine-out soot, with respect to the baseline conventional diesel combustion engine vehicle., The authors acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R). The authors also acknowledge the Universitat Politecnica de Valencia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (SP20180148).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Sizing a conventional diesel oxidation catalyst to be used for RCCI combustion under real driving conditions

  • García Martínez, Antonio|||0000-0001-5783-4936
  • Piqueras, P.|||0000-0002-3767-0839
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Lago-Sari, Rafael
[EN] Reactivity controlled compression ignition (RCCI) combustion has demonstrated to be able to avoid the NOx-soot trade-off appearing during conventional diesel combustion (CDC), with similar or better thermal efficiency than CDC under a wide variety of engine platforms. However, a major challenge of this concept comes from the high hydrocarbon (HC) and carbon monoxide (CO) emission levels, which are orders of magnitude greater than CDC, and similar to those of port fuel injected (PFI) gasoline engines. The high HC and CO emissions levels combined with the low exhaust temperatures during RCCI operation could present a challenge for the current exhaust aftertreatment technologies. The objective of this work is to evaluate the potential of a conventional diesel oxidation catalyst (DOC) for light-duty diesel engines when operating under dual-fuel RCCI diesel-gasoline combustion and to define its necessary size to accomplish with the current emissions standards. For this purpose, a 1-D model has been developed and calibrated through gas emissions measurements upstream and downstream the DOC under different engine steady-state conditions. After that, the DOC response in transient conditions has been evaluated by means of vehicle systems simulations under different driving cycles representative of the homologation procedures currently in force around the world. The results show that the HC and CO levels at the DOC outlet are unacceptable considering the different emissions regulations. By this reason, a dedicated study to define the DOC size needed to accomplish the different emissions standards is carried out. The results suggest that, the DOC volume needed to fulfill the type approval regulation limits ranges from four to six times the original volume., The authors gratefully acknowledge General Motors Global Research & Development for providing the engine used in this investigation. The authors also acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Methanol and OMEx as fuel candidates to fulfill the potential EURO VII emissions regulation under dual-mode dual-fuel combustion

  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Villalta-Lara, David
  • Guzmán-Mendoza, María Gabriela
[EN] Recent investigations show that there are different combustion strategies that promise to achieve higher efficiencies in internal combustion engines. Advanced combustion modes such as reactivity controlled compression ignition (RCCI) and dual-mode dual-fuel (DMDF) have proven to be able to achieve low NOx and soot engine-out emissions while being able to operate over the complete engine map. On another front, intensive research has been done in the fuels field. Oxygenated fuels, like oxymethylene dimethyl ethers (OMEx) and methanol, are of special interest because of their potential to reduce the soot emissions, while allowing to adjust parameters, such as EGR, to higher values to also reduce NOx emissions and avoid other problems like excessive in-cylinder peaks of pressure. In this research, the effects of diesel-methanol and OMEx-gasoline fuels were studied on a dual-mode dual-fuel (DFDM) multi-cylinder engine at 1800 rpm for various loads (25, 50, 80 and 100%). To do so, a dedicated calibration to optimize the brake thermal efficiency while trying to maintain NOx and soot emissions under EURO VI limitations was applied. Then, the combustion characteristics, performance and emissions results are compared to a base diesel-gasoline case. Boundary conditions (intake pressure, temperature and air mass) for each fuel combination where similar, with the exception of the premixed energy ratio, which was on average 20% lower for diesel-methanol. Each fuel combination was, weighted against each other by means of an merit function, where the fuel combination with the lowest value has the closest approximation to ideal BSFCeq, BSNOx, BSSoot, BSCO and BSHC targets. Results show that diesel-methanol presents no significant differences with respect to diesel-gasoline in terms of equivalent BSFCeq and NOx, while the substitution of diesel by OMEx in the dual-mode dual-fuel combustion has the potential of, although penalizing HC and CO emissions, not only achieving the EURO VI NOx (0.4 g/kWh) limits but also the future potential EURO VII (0.2 g/kWh) as well because of a negligible soot production that allows using EGR levels of up to 50%., The authors thanks ARAMCO Overseas Company and VOLVO Group Trucks Technology for supporting this research. The authors acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA201787694-R). The authors also acknowledge the Universitat Politecnica de Val`encia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (PAID-06-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Assessment of a complete truck operating under dual-mode dual-fuel combustion in real life applications: Performance and emissions analysis

  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Lago-Sari, Rafael
  • Gaillard,Patrick
[EN] The dual-mode dual-fuel (DMDF) strategy has been demonstrated to be a potential combustion mode to cover all the engine map with low-to-moderate NOx and soot emissions and high efficiency simultaneously. This can be accomplished by modifying the injection strategy to promote a fully premixed or a dual-fuel diffusive combustion depending on the operating conditions. The main limitation of the DMDF are the high concentrations of unburned hydrocarbons and carbon monoxide coupled with low exhaust temperatures, which can be a challenge for the stock diesel oxidation catalyst (DOC). Moreover, the use of a diffusive combustion combined with high EGR rates to avoid mechanical issues at high load enhances the soot formation, which can compromise the final soot levels in a homologation cycle. To evaluate these aspects, this work studies the performance and emissions of a DMDF truck concept along a WHVC and different in-service conformity cycles through vehicle systems simulations. For both types of cycles, five payloads were tested (0%, 25%, 50%, 75% and 100%) to evaluate the impact of this parameter on the operating points distribution inside the DMDF map. The first results show that the DMDF concept provides engine-out NOx levels below the EUVI regulation at normative payload (50%) with similar fuel consumption than the conventional diesel truck. On the other hand, the engine-out HC and CO emissions exceed their respective limits in all the cases, while the engine-out soot emissions only reach the EUVI levels up to 25% payload. By this reason, the stock DOC and diesel particulate filter from the conventional diesel truck were modelled and fitted to the DMDF truck model. The results evidenced that the use of these two ATS allows to achieve the EUVI limits in terms of tailpipe HC, CO and soot independently on the cycle and payload analyzed. Moreover, considering the tailpipe emissions values achieved with ATS at 50% payload, it can be inferred that both devices could be downsized for the DMDF application as compared to the conventional ATS for diesel applications., The authors thanks ARAMCO Overseas Company and VOLVO Group Trucks Technology for supporting this research. The authors acknowledge European Regional Development Fund (FEDER) and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R). The authors also acknowledge the Universitat Polit`ecnica de Val`encia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (SP20180148). The author R. Sari acknowledges the financial support from the Spanish ministry of science innovation and universities under the grant ``Ayudas para contratos predoctorales para la formaci ' on de doctores"(PRE2018-085043).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental investigation on the efficiency of a diesel oxidation catalyst in a medium-duty multi-cylinder RCCI engine

  • Benajes, Jesús|||0000-0002-1653-9188
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Lago-Sari, Rafael
[EN] Reactivity controlled compression ignition (RCCI) combustion is one of the most promising low temperature combustion (LTC) techniques, as it is able to provide ultra-low NOx and soot emissions together with higher thermal efficiency than conventional diesel combustion (CDC) in a wide range of operating conditions. However, the unburned hydrocarbon (UHC) and carbon monoxide (CO) emission levels are orders of magnitude higher than CDC, which can result in a major problem for implementing the RCCI concept in real engines. In this sense, the high levels of UHC and CO emissions together with the low exhaust temperatures during RCCI operation could compromise the diesel oxidation catalyst (DOC) conversion efficiency. The objective of this work is to evaluate the efficiency of a conventional DOC in oxidizing the UHC and CO emissions from RCCI combustion. To do this, a medium-duty multi-cylinder diesel engine equipped with its original after treatment system has been used. First, the DOC conversion efficiency is evaluated under some steady-state conditions. Later, the influence of the thermal inertia on the DOC response has been evaluated by means of transient tests. In this sense, different engine load-speed steps as well some simplified conditions from the worldwide harmonized vehicle cycle (WHVC) and the supplemental engine transient cycle (SET) are evaluated. In steady-state conditions, with DOC-inlet temperatures of 200-300 degrees C, the results show conversion efficiencies of 100% for CO and 85-95% for HC. At 10% and 25% load, the DOC-outlet UHC levels are unacceptable considering the EURO VI regulation, while at 50% load the tailpipe emissions fulfill the emissions standard. The results in transient conditions are more promising thanks to effect of the thermal inertia, showing 100% conversion efficiency for CO and greater than 90% for UHC during large periods of engine operation., The authors thanks VOLVO Group Trucks Technology and ARAMCO Overseas Company for supporting this research. The authors also acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Surrogate Fuel Formulation to Improve the Dual-Mode Dual-Fuel Combustion Operation at Different Operating Conditions

  • Benajes, Jesús|||0000-0002-1653-9188
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Lago-Sari, Rafael
[EN] Dual-mode dual-fuel combustion is a promising combustion concept to achieve the required emissions and CO2 reductions imposed by the next standards. Nonetheless, the fuel formulation requirements are stricter than for the single-fuel combustion concepts as the combustion concept relies on the reactivity of two different fuels. This work investigates the effect of the low reactivity fuel sensitivity (S=RON-MON) and the octane number at different operating conditions representative of the different combustion regimes found during the dual-mode dual-fuel operation. For this purpose, experimental tests were performed using a PRF 95 with three different sensitivities (S0, S5 and S10) at operating conditions of 25% load/950 rpm, 50%/1800 rpm and 100%/2200 rpm. Moreover, air sweeps varying ±10% around a reference air mass were performed at 25%/1800 rpm and 50%/1800 rpm. Conventional diesel fuel was used as high reactivity fuel in all the cases. Moreover, commercial 95 RON gasoline was used as reference to compare the different TRFs. The engine settings were managed to adjust the rate of heat release to that found with 95 RON gasoline. To do this, a quality index imposing a maximum deviation of 5% point-to-point between the HRR curves from both fuels was defined. The results suggest that PRF 95 with S0 has the most similar behavior compared to conventional 95 RON gasoline whatever the engine load. As the engine load increases, the sensitivity effect is more noticeable and iso-HRR operation was only possible for S0. At low and medium load, the TRFs present similar engine-out emissions with equal fuel consumption. At full load, the NOx emissions are increased with respect to the reference 95 RON gasoline without fuel consumption benefits. The results from the air variation for the different octane numbers demonstrated that the greatest differences are obtained for low air mass (i.e, higher EGR). In addition, the decrease of the octane number limits the maximum air increase due to the pressure gradients, requiring modifications in the engine settings that increase the soot formation., The authors thanks VOLVO Group Trucks Technology and ARAMCO Overseas Company for supporting this research. The authors also acknowledge FEDER and Spanish Ministerio de Economía y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R) and the Universitat Politècnica de València for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigación (PAID-06-18). The author R. Sari acknowledges the financial support from the Spanish ministry of science innovation and universities under the grant ¿Ayudas para contratos predoctorales para la formación de doctores¿ (PRE2018-085043).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Potential of RCCI Series Hybrid Vehicle Architecture to Meet the Future CO2 Targets with Low Engine-Out Emissions

  • Benajes, Jesús|||0000-0002-1653-9188
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Lago-Sari, Rafael
[EN] Reactivity controlled compression ignition (RCCI) combustion has been shown to provide simultaneous ultra-low NOx and soot emissions with similar or better thermal efficiencies than conventional diesel combustion (CDC). Nonetheless, RCCI still has several challenges that restrict its operating range and limit its practical application. The dual-mode operation, which involves switching between different combustion modes, has been found as a promising alternative to operation in the whole engine map. However, the combustion mode switching requires difficult engine control, particularly during transient operation. The series hybrid vehicle (SHV) architecture allows the thermal engine to operate in a limited operating range by decoupling it from the drivetrain. Therefore, it could be an interesting alternative to the dual-mode concept. This work explores the potential of the RCCI series hybrid vehicle architecture to provide low engine-out emissions and CO2 by means of vehicle systems simulations. The results show the influence of the main parameters and control strategies of the SHV vehicle on its efficiency and emissions under different driving cycles. Finally, the optimal RCCI-SHV configuration is compared to CDC and dual-mode combustion strategies, confirming its potential as a future vehicle architecture for high efficiency and low emissions., This research was funded by FEDER and Spanish Ministerio de Economia y Competitividad through the TRANCO project, with grant number TRA2017-87694-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental study of influence of Liquefied Petroleum Gas addition in Hydrotreated Vegetable Oil fuel on ignition delay, flame lift off length and soot emission under diesel-like conditions

  • Pastor, José V.|||0000-0003-4113-4681
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Micó, Carlos|||0000-0001-5787-6212
  • Garcia-Carrero, Alba Andreina
[EN] The fundamental behaviour on ignition and combustion characteristics of blends of Hydrotreated Vegetable Oil and Liquid Petroleum Gas was investigated in a constant high pressure, high temperature combustion chamber, using a prototype lab-scale injection system adapted from a conventional common-rail system to conduct the injection events, ensuring that fuel was liquid at any point of the injection system and avoiding the formation of fuel vapour bubbles that could alter the injected fuel behaviour. The ignition delay, flame lift-off length and the soot formation were studied by means of high-speed imaging techniques, for different operating conditions. The aim of the work is to characterize the effect of Hydrotreated Vegetable Oil-Liquid Petroleum Gas blend ratios on the previously mentioned parameters. Experimental results show that the behaviour of the fuel blends follow the expected trends of conventional diesel type fuels when varying ambient temperature, density and injection pressure. Hydrotreated Vegetable Oil, being the highest reactivity fraction, controls auto ignition of the blend. However, Liquid Petroleum Gas acts as combustion inhibitor increasing both ignition delay and lift-off length as its ratio in the blend increases. As a consequence, the differences observed in terms of flame radiation suggest that increasing Liquid Petroleum Gas fraction reduces soot formation as it promotes a higher air/mixture., The authors acknowledge that this research work has been partly funded by the Government of Spain and FEDER under TRANCO project (TRA2017-87694-R) and by Universitat Politècnica de València through the Programa de Ayudas de Investigación y Desarrollo (PAID01-18) program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Development of a soot radiation model for diesel flames

  • López, J. Javier|||0000-0002-9486-2511
  • García-Oliver, José M|||0000-0002-2676-9681
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Villalta-Lara, David
[EN] This paper describes a radiation model for diesel sprays that can predict the heat losses based on spray characteristics to the spray plume due to radiation. The model is based on three sub-models: spray model, soot model and radiation model. The spray model is a one-dimensional model that simulates the axial and radial distribution of a fuel spray for each instant. The soot model is a one-dimensional tool, which is based on formation and oxidation processes calculating the axial and radial soot concentration profile for each instant. The output results of the two sub-models are used as input information for the radiation model, which obtains the radiation heat transfer values for a diesel flame. The experimental measurements used to adjust the different constants and to validate the sub-models were performed in a high-pressure high-temperature vessel using three different optical techniques: Schlieren, to obtain spray penetration, Diffused Back-Illumination technique (DBI) for the soot concentration and the 2-color method for calculating the soot temperature and concentration. The radiant fraction shows values from 0.11% to 0.43% with respect to the total energy of the fuel depending on the operating condition. Taking into account the different assumptions taken for modeling the spray radiation, these results are consistent with those obtained in the literature, in which the radiation was characterized under similar conditions., The authors acknowledge FEDER and Spanish Ministerio de Economía y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Computational optimization of the dual-mode dual-fuel concept through genetic algorithm at different engine loads

  • Xu, Guangfu
  • Jia, Ming
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • García Martínez, Antonio|||0000-0001-5783-4936
[EN] The diesel/gasoline dual-mode dual-fuel (DMDF) combustion concept was optimized in a compression-ignition engine by combining the computational fluid dynamics (CFD) simulations with the genetic algorithm. Seven operating parameters with remarkable influences on the engine performance were chosen as the variables to be optimized for simultaneously minimizing the fuel efficiency, nitrogen oxides (NOx), and soot emissions. Moreover, the potential of the further improvement of the DMDF combustion concept was discussed, and the rationality of this strategy was demonstrated. The results indicate that, at low load, simultaneous improvement of the fuel economy and emissions can be realized by strengthening the homogeneous combustion. At mid load, the fuel economy can be improved by reducing the heat transfer losses, while the NOx emissions are sacrificed to some extent. At high load, improved fuel economy can be realized by transferring a part of diffusion combustion to premixed reactivity-controlled compression ignition (RCCI) combustion. Concerning the operating parameters, lower intake temperature is beneficial to decrease the transfer losses, and the control of intake temperature is crucial for the stable operation of DMDF combustion under wide load conditions. Overall, gross indicated thermal efficiency above 45% is achieved, and the NOx and soot emission can be maintained under the Euro 6 standard for the test load range., This work was partially supported by the National Natural Science Foundation of China (Grant Nos. 51961135105 and 91641117) and China Postdoctoral Science Foundation (Grant No. 2019M661094). The experimental results used in this investigation were obtained in a project funded by VOLVO Group Trucks Technology. The authors also acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R) and the Universitat Politecnica de Valencia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (PAID-06-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Potential of bio-ethanol in different advanced combustion modes for hybrid passenger vehicles

  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Martínez-Boggio, Santiago Daniel
  • Roso, Vinicius Ruckert
  • Souza Alvarenga Santos, Nathalia Duarte
[EN] The strong new restrictions in the vehicle CO2 emissions together with the instability of the fossil fuels reserves reinforces the necessity to continue developing high efficiency combustion engines that operate with renewable energy sources. Bio-ethanol appears as a potential fuel to replace well-established fossil fuels, such as gasoline, due to the overall carbon neutral emission. In addition, the high-octane number allows to increase the compression ratio of the engine to improve the thermal efficiency. Apart from the CO2, the emissions legislation restricts the NOx and particle matter emissions to ultra-low values, and they will continue decreasing down to almost zero. In this work, two advanced dual-fuel combustion modes using bio-ethanol as main fuel are studied. A pre-chamber ignition system (PCIS) using bio-ethanol and hydrogen, and a reactivity-controlled compression ignition (RCCI) combustion mode operating with bio-ethanol/diesel was selected due to the potential to reduce NOx emissions. These combustion technologies were studied by a numerical 0-D vehicle simulations in homologation and real-life driving cycles for a range extender hybrid powertrain. As a baseline, the original manufacturer spark ignition (SI) no-hybrid powertrain fueled with pure bio-ethanol was used. The powertrain components and control system were optimized to obtain the maximum overall vehicle efficiency, and low CO2-NOx emissions. Finally, a life cycle analysis (LCA) was performed to study the global potential of the bio-ethanol to reduce greenhouse gas (GHG) emissions. A battery electric vehicle (BEV) and a gasoline SI no-hybrid vehicle were added for comparison. The results show that the RCCI mode presents the highest potential to reduce the NOx emissions. However, the PCIS allows to reduce the tank to wheel CO2 emissions up to 60 g/km when high rates of H2 are used. The LCA-GHG for the vehicles using bio-ethanol is 50% and 95% lower than a BEV and SI-gasoline vehicle, respectively., The authors acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R). The authors also acknowledge the Universitat Politecnica de Valencia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (SP20180148). The authors also acknowledge CAPES and the Post-Graduation Program in Mechanical Engineering at UFMG-Brazil for the support provided.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Combustion improvement and pollutants reduction with diesel-gasoline blends by means of a highly tunable laser plasma induced ignition system

  • Pastor, José V.|||0000-0003-4113-4681
  • García-Oliver, José M|||0000-0002-2676-9681
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Micó, Carlos|||0000-0001-5787-6212
[EN] The use of alternative fuels in compression ignition engines, either completely or partially replacing the conventional ones, have potential to reduce pollutant emissions (especially soot). However, some of these fuels do not provide good ignition features under diesel engine like conditions, which affects engine efficiency. Thus, in order to extend the application of alternative fuels, the current research proposes the use of a laser induced plasma ignition system to assist on the combustion of blends of fuels with less reactivity than pure diesel. This fuel has been chosen as the base component and it has been mixed with gasoline (as the low-reactivity fuel) in different ratios as an example of fuels with very different reactivity properties. Tests have been performed in a single cylinder optically accessible engine, allowing deeper study of combustion development and soot formation. For different in-cylinder conditions and fuel blends, the effect of laser induced plasma ignition system has been evaluated at different crank angle degrees and locations inside the combustion chamber. The application of these blends under low-reactivity engine conditions show that combustion efficiency is dramatically affected. However, the study proves that it is possible to control blend ignition delay and flame lift-off length by means of laser induced plasma. Besides, using the proper ignition system configuration, combustion characteristics similar to those of diesel fuel autoignition can be achieved for high gasoline substitution rates. They lead to similar energy release rates, which confirms that diesel-gasoline blends can reach a combustion efficiency close to pure diesel, while a strong reduction on soot formation was also obtained. These results open a door to efficiency improvement and pollutant reduction by means of a highly tunable ignition of alternative fuel blends., The authors acknowledge that this research work has been partly funded by the Government of Spain and FEDER under TRANCO project (TRA2017-87694-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Potential of 1-octanol and di-n-butyl ether (DNBE) to improve the performance and reduce the emissions of a direct injected compression ignition diesel engine

  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Villalta-Lara, David
  • Zubel, Marius
  • Pischinger, Stefan
[EN] This experimental work evaluates the potential of 1-octanol, di-n-butyl ether and three intermediate blends as substitutes of the diesel fuel to be used in compression ignition engines. For this purpose, performance and engine-out emissions measurements have been done in a single-cylinder engine of 0.39 L displacement and 15:1 compression ratio at four engine operating conditions representative of the new European driving cycle (NEDC) driving cycle. The tests have been done keeping constant the NOx emissions and combustion center for all the fuels at each operating point. To achieve this, the exhaust gas recirculation rate and the start of injection timing were modified simultaneously for each fuel tested, while the rest of the engine settings were kept constant. All the biomass-derived fuels have the same oxygen content but substantially different cetane number and volatility. The results show that, for the same NOx levels, all the fuels allow a substantial reduction of the soot emissions versus diesel due to both the higher oxygen content in the fuel molecule and/or the extended mixing time achieved because of the lower fuel reactivity. In terms of efficiency, all the alternative fuels improve the fuel-to-work conversion efficiency. This benefit comes from decreasing the heat transfer in a greater way than the exhaust losses increase. Moreover, in general terms, all the fuels promote a reduction of the combustion losses to halve of those found with diesel., The authors gratefully acknowledge FEDER and Spanish Ministerio de Economía y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R). This work was performed as part of the Cluster of Excellence Tailor-Made Fuels from Biomass, which is funded by the Excellence Initiative by the German federal and state governments to promote science and research at German universities. Thus, the authors would like to thank the Institute for Combustion Engines, RWTH Aachen University, for all the support to perform the research activities.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Tesis de maestría (MasterThesis)

El mismo motor, nuevos combustibles: Extendiendo la vida de los motores de combustión interna con e-fuels más allá de las regulaciones futuras.

  • Guzmán Mendoza, María Gabriela
[ES] A medida que los efectos del calentamiento global se hacen más severos, el estudio de alternativas para tratar de frenarlos, o incluso detenerlos, aumenta su importancia. El sector de transporte es uno de los principales contribuyentes a los insidiosos gases de efecto invernadero (GEI), y como tal este sector debe estar a la vanguardia del desarrollo de estrategias que reduzcan las emisiones globales. Por otro lado, los entes reguladores de emisiones se han vuelto más estrictos con cada nueva iteración de normativa, y actualmente, nos encontramos en la cúspide de nuevas normativas que podrían no dejar cabida para los motores de combustión interna en años posteriores al 2025. La tendencia para los vehículos ligeros es la electrificación. Sin embargo, la electrificación completa del parque automotor tomará tiempo, inversión de capital y adaptación del consumidor debido a que los vehículos eléctricos (VE) todavía presentan altos costos de producción, menos puntos de carga, un rango de distancia menor, y un tiempo de carga mayor que sus contrapartes de combustión interna. En el caso de las flotas de vehículos pesados, estas limitaciones continúan representando un impedimento para la adopción de los Ves a causa de las demandas de rentabilidad, peso y distancia requeridas. Alternativas diferentes a la conversión a eléctricos deben también ser exploradas y serán tremendamente importantes en regiones donde la red eléctrica se conforme de fuentes de generación desfavorables para el medio ambiente, se encuentre en mal estado o desarrollo, o el costo de substitución de vehículos sea prohibitivo. En tal sentido, el uso de combustibles alternativos que no contribuyan hacia los gases de efecto invernadero gana relevancia a medida que las políticas para lograr cero emisiones entran en vigor alrededor del mundo. El estudio de combustibles que puedan tener propiedades energéticas similares a las de los combustibles convencionales (diésel y gasolina), pero con menores emisiones del motor y emisiones netas de producción igual a cero, al mismo tiempo que se mantienen usables como substitutos de aplicación directa donde ni el motor ni el tren motriz deben ser modificados se convierte en un esfuerzo digno de entender a profundidad. Habiendo dicho lo anterior, el presente trabajo se enfoca al estudio de los efectos de los e-fuels como el OMEx, el metanol y el metano en motores de encendido por compresión, actuando bajo modos de combustión de baja temperatura con combustible dual, para evaluar el potencial de reducción de emisiones sin desmejorar la eficiencia y el consumo de combustible. Estrategias de calibración diferentes son utilizadas para obtener una fase de combustión optimizada. Durante el estudio se encuentra que las emisiones de especies contaminantes como el NOx y el hollín pueden ser reducidas con respecto a las contrapartes tradicionales. Otro hito importante se asocia a que, si la síntesis del combustible se realiza utilizando fuentes renovables, el CO2 (una de los principales contribuyentes a los GEI) del ciclo de vida del combustible puede ser potencialmente cero en su suma neta., [EN] As the effects of global warming become more dire, the study of alternatives to try to delay it, or even stop it, become increasingly important. The transport sector is one of the main contributors to the insidious greenhouse gases (GHG), and as such should be at the forefront of the development of strategies that reduce global emissions. On the other side, emissions regulators have become stricter with every new iteration of normative, and currently we are on the cusp of new rulings that could potentially leave no room to the use of internal combustion engines beyond 2025. The tendency for light-duty vehicles is to become electrified. However complete electrification of the automotive park will take time, capital investment and consumer adaption since electric vehicles (EV) still present higher production costs, less charging stations, a shorter range, and a longer time to replenish its energy than internal combustion vehicles. In the case of heave-duty fleets these limitations still represent a significant impediment for the adoption of EVs due to their rentability, weight and distance demands. Alternatives different to electrification should also be explored and will be tremendously important in regions where the electric grid is not comprised of mainly green sources, is not as well developed, or the cost of vehicle substitutions is prohibitive. In that sense, the use of alternative fuels that do not contribute to greenhouse gases is gaining relevance as policies to move to zero emissions come into force across the world. The study of fuels that can have similar energetic properties as conventional fuels (diesel and gasoline), but with less engine-out emissions and net-zero production emissions, while remaining usable as drop-in substitutes where neither the engine nor the drivetrain has to be modified becomes an insightful endeavor. Having said the above, the present work is dedicated to the study of the effect of e-fuels like OMEx, methanol and methane on compression ignition (CI) internal combustion engines under dual-fuel low-temperature combustion modes to assess the potential for emissions reductions while maintaining good levels of efficiency and fuel consumption. Different calibrations methodologies are applied to obtain an optimized combustion phasing. Through the study it is found that engine-out emissions of polluting species like NOx and soot can be reduced with respect to their conventional counterparts. Another important highlight is the fact that given the fuels are synthetized employing renewable sources, the CO2 (one of the main contributors to GHG) through the lifecycle of the fuel can potentially be net-zero., The authors thanks ARAMCO Overseas Company and VOLVO Group Trucks Technology for supporting this research. The authors acknowledge FEDER and Spanish Ministerio de Economía y Competitividad for partially supporting this research through TRANCO project (TRA2017- 87694-R). The authors also acknowledge the Universitat Politècnica de València for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigación (PAID-06-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Tesis de maestría (MasterThesis)

Evaluation of RCCI combustion using OMEx for pollutant emissions reduction, Evaluación de la combustión RCCI usando OMEx para la reducción de contaminantes

  • Fogué Robles, Álvaro
[ES] Las nuevas normativas reducirán de forma significativa los niveles aceptables de óxidos de nitrógeno (NOx) y hollín de los motores, lo que implica reducir notablemente las temperaturas alcanzadas dentro del cilindro y emplear mezclas de aire-combustible muy diluidas. A su vez, los objetivos de reducción de emisiones de CO2 propuestos también implican que el consumo total de combustible debe reducirse de forma proporcional, lo que se traduce en un aumento de la eficiencia térmica del motor. Para satisfacer ambos requisitos, mayor eficiencia y menores emisiones, la comunidad científica ha ideado lo que se conoce como modos de combustión de baja temperatura (LTC), en los que se emplean mezclas de aire y combustible altamente homogéneas para reducir las temperaturas en la cámara de combustión respecto a los modos de combustión tradicionales para así producir menos emisiones. Dentro de la amplia gama de LTC desarrollados recientemente, el modo de combustión Reactivity Controlled Compression Ignition (RCCI) ha demostrado tener cierta ventaja con respecto a otros LTC como el HCCI o el PPC, ya que permite cierta flexibilidad para controlar la tasa de combustión y así poder extender el rango operacional del motor al mismo tiempo que mantiene niveles de emisiones similares a los otros LTC. El RCCI ha sido combinado con la combustión dual-fuel en lo que se conoce como combustión DMDF (Dual-Mode Dual-Fuel), que permite extender el rango operacional del RCCI a todo el mapa motor por medio de una estrategia basada en mezclas altamente homogéneas a baja carga de motor y mezclas más estratificadas y difusivas en puntos de alta potencia. El modo de combustión DMDF utilizado con combustibles convencionales como diésel y gasolina es capaz de mantener un rendimiento y emisiones de CO2 similares a los modos de combustión convencionales y obtener una reducción en las emisiones de NOx y hollín capaz de cumplir con la normativa EU VI en condiciones de operación por debajo de cierto nivel de potencia. A pesar de esto, cuando esta tecnología se evalúa bajo condiciones de conducción realistas es capaz de cumplir con los requisitos de homologación. Pensando ya en la aplicación de este concepto, es posible contribuir también a la reducción de emisiones de CO2 mediante el uso de combustibles sintéticos que se formulan utilizando CO2 capturado directamente de la atmósfera. Dentro de estos, los combustibles altamente oxigenados como el OMEx sin enlaces carbono-carbono en la molécula tienen la habilidad de no producir hollín incluso bajo estrategias de combustión altamente difusivas. Como desventaja, estos combustibles tienden a tener una densidad energética relativamente baja y esto puede afectar a la autonomía del vehículo. Se ha demostrado que usando gasolina y OMEx bajo el modo de combustión DMDF proporciona grandes ventajas en la reducción de emisiones ya que no produce hollín en ningún punto de operación y es capaz de alcanzar niveles EU VI en emisiones de NOx en todo el mapa motor al mismo tiempo que aumenta ligeramente la eficiencia térmica (que se traduce en un menor uso de energía) y contribuye a la reducción de emisiones de CO2 WtW mientras que el impacto en la autonomía del vehículo se reduce a niveles aceptables que se pueden solventar con un ligero aumento de la capacidad del depósito. Los últimos avances en el uso de DMDF OMEx-Gasolina convierten esta alternativa en un potencial sustituto a los motores convencionales, pero aun quedan muchas preguntas sin responder con respecto a la aplicabilidad de este concepto. En un intento de aclarar algunas de estas cuestiones, este trabajo evalúa el impacto del uso de combustibles de baja densidad energética en el sistema de inyección y estudia la capacidad de la tecnología actual para adaptarse al nuevo escenario. Además, como se espera un aumento en la exigencia de la normativa de homologación en los próximos años, este trabajo también, [EN] The projected future for internal combustion engines supposes a great challenge in terms of controlling the combustion products. Future normative will significantly reduce the accepted pollutants levels like nitrogen oxides (NOx) and soot, which requires to significantly reduce the in-cylinder temperatures and use highly diluted fuel to air mixtures. In addition, the objectives for greenhouse gasses reduction like CO2 imply that the total fuel consumption must be reduced proportionally, which means that the engine thermal efficiency has to be improved. To comply with both requirements of high thermal efficiency and low emission levels, the scientific community has devised what is known as low temperature combustion modes (LTC), in which highly homogeneous fuel-air mixtures produce lower in-cylinder temperatures compared to conventional combustion modes and significantly reduce the pollutant emissions. Within the family of the recently developed LTC, the RCCI (Reactivity-Controlled Compression Ignition) combustion mode has demonstrated to have a significant advantage with respect to other LTC like HCCI and PPC, as it allows certain flexibility to better control the combustion rates and extend the operational limits of the engine while keeping similar emission properties. The combination of dual-fuel combustion with RCCI is known as DMDF (Dual-Mode Dual-Fuel) combustion, which provides the capability to extend the operational range of RCCI to the complete engine map by designing a strategy in which a highly mixed load is used at low engine loads and a more diffusive and stratified combustion is employed at higher engine loads. The DMDF used with conventional fuels like diesel as a high reactivity fuel and gasoline as the low reactivity fuel can provide similar engine efficiency and CO2 emissions than conventional combustion modes, but NOx and soot reduction is only able to fulfil current EU VI normative up to a certain engine power level. Nonetheless, when it is evaluated under realistic driving conditions it can comply with homologation scenarios. Looking further in the application of this concept, it is possible to contribute to the CO2 reduction by using synthetic fuels that have been produced using CO2 present in the atmosphere as a raw material. Synthetic fuels also have the advantage of having a molecular structure that can be designed and tuned by different refining processes obtaining certain chemical properties that can be beneficial for the emissions reduction. Specifically, highly oxygenated fuels like OMEx with no carbon-carbon molecular bonds have the capability of not producing soot even at highly diffusive combustion strategies. The main drawback of synthetic oxygenated fuels is that they normally have a much lower energy density and can significantly impact the vehicle autonomy. It has been proven that DMDF combustion strategy using gasoline and OMEx provides a huge impact on NOx and soot reduction being able to fulfil normative levels in all the engine map, improve the engine thermal efficiency (which directly implies a reduction of the energy consumption) and contribute to the CO2 reduction in well-to-wheel (WtW) terms while having an acceptable impact in the autonomy of the vehicle that can be easily managed with a slightly bigger fuel tank volume. The latest results with this OMEx-Gasoline DMDF engines make of this alternative a potential substitute for conventional ICEs, but there still are many questions to be answered regarding the applicability of such technology. As an attempt to bring light over some of these questions, this work has evaluated the impact of using low energy density fuels on the injection system and evaluate the feasibility of current technological solutions to be adapted to this new scenario. Additionally, as it is expected that the current homologation normative will be updated to a more restrictive criteria in the future years, in this work it has also been evaluated the possibili, The authors thanks VOLVO Group Trucks Technology and ARAMCO Overseas Company for supporting this research. The authors also acknowledge FEDER and Spanish Ministerio de Economía y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R) and the Universitat Politècnica de València for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigación (PAID-06-18). The authors acknowledge the Conselleria de Innovación, Universidades, Ciencia y Sociedad Digital de la Generalitat Valenciana for partially supporting this research through grant number GV/2020/017.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Effectiveness of hybrid powertrains to reduce the fuel consumption and NOx emissions of a Euro 6d-temp diesel engine under real-life driving conditions

  • Luján, José M.|||0000-0001-6133-8943
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Martínez-Boggio, Santiago
[EN] Recent investigations demonstrated that the real-world driving conditions differ from those proposed in the homologation cycles. This provokes that the emissions levels in real-life conditions exceed the normative values, as shown in the recent scandal related to the NOx emissions from the passenger cars equipped with diesel engines. On the other hand, the upcoming emissions regulations will limit the CO2 emissions to very low levels, which demands a further optimization of the existing technology. One way to reduce the NOx and CO2 emissions is by electrifying the powertrain in a certain degree. The objective of this work is to evaluate the potential of implementing a parallel (P2) hybrid architecture in a compact car (class C) equipped with a diesel 1.6 Euro 6d-temp engine to reduce the emissions and fuel consumption in homologation and real-life driving cycles. This has been done using a OD numerical vehicle model and the experimental engine maps of fuel consumption and emissions measured at steady state conditions. After that, the transient conditions were simulated in homologation cycles and real-life driving cycles measured by the authors in Spain. The numerical model was validated against experimental tests carried out in an active engine test bench, evidencing differences below 4% under the worldwide harmonized light vehicles test cycle (WLTC). In the real-life cycles, the hybridization of the powertrains improves the fuel consumption for all types of driving cycles (urban, combined and highway). The major benefits are obtained in urban driving cycles, with gains up to 50% in fuel consumption and CO2 emissions. In addition, the improvements in real-life conditions are higher than in the urban phase of the homologation cycles. On the contrary, combined real-life cycles (urban + rural + highway) show lower benefits than the homologation cycle. This is due to different energy management strategy that needs to be adapted to each driving situation. Lastly, it was found that, contrarily to the case of the homologation cycle, the NOx emissions are not reduced with the hybridization of the diesel powertrain in real-life conditions. Thus, to achieve 2021 CO2 target (95 g/km) and to reduce aftertreatment systems in diesel engines, other vehicles technologies need to be added to the full hybridization., The authors acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R). The authors also acknowledge the Universitat Politecnica de Valencia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (PAID-06-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental Study of the Influence of Gasoline-Diesel Blends on the Combustion Process and Soot Formation under Diesel Engine-Like Conditions

  • Pastor, José V.|||0000-0003-4113-4681
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Micó, Carlos|||0000-0001-5787-6212
  • Garcia-Carrero, Alba Andreina
[EN] Recent research has demonstrated that a reduction in pollutant emissions of diesel engines can be achieved by using high octane fuels such as gasoline, methane, or liquefied petroleum gas. Therefore, in this study, the focus was to investigate the influence of blends of diesel and gasoline on combustion characteristics such as ignition delay, rate of heat release, and lift-off length as well as the influence on soot formation. The experiments were carried out in a test rig with optical access which mimics a single-cylinder diesel engine. Four blends were tested: one blend with 100% diesel and then three diesel-gasoline blends with 30%, 50%, and70% gasoline. The blends were made in volumetric proportions and injected using a common rail injection system without any kind of modification. The ignition delay and the apparent heat release were obtained by means of the in-cylinder pressure signal. Furthermore, the combustion development and soot formation were studied using three optical techniques: OH* chemiluminescence, natural luminosity, and diffused back-illumination extinction imaging (DBI). Different engine operating conditions were analyzed. Results showed that ID increases with the gasoline content in the blend. Similarly, as the reacting time increased, the lift-off length was longer. On the other hand, the apparent rate of heat release decreased due to a reduction of the fuel injection rate, which depends on the density of the blend. In addition, differences in the flame radiation were also observed. Gasoline-diesel blends had less luminosity, which is related to less soot formation. To confirm this, the KL factor obtained from the DBI technique was determined, and it was concluded that increasing the gasoline fraction in the blend reduces soot formation., This research work has been partly funded by the Government of Spain and FEDER under TRANCO project (TRA2017-87694-R) and by Universitat Politecnica de Valencia through the Programa de Ayudas de Investigacion y Desarrollo (PAID-01-18 and PAID-06-18) program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Computational optimization of the piston bowl geometry for the different combustión regimes of the dual-mode dual-fuel (DMDF) concept through an improved genetic algorithm

  • Xu, Guangfu
  • Jia, Ming
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
[EN] Focusing on the dual-mode dual-fuel (DMDF) combustion concept, a combined optimization of the piston bowl geometry with the fuel injection strategy was conducted at various loads. An improved genetic algorithm was introduced in this study, which is superior in searching for the global optimal solutions. The optimal piston bowl shape coupled with the corresponding injection strategy was summarized at the various loads. The results show that the piston bowl geometry optimization can further improve the thermal efficiency with 1.4%, 4.4%, and 1.4% percentage points for the low, mid, and high loads, respectively. An indicated thermal efficiency up to 51.8% can be realized at mid load. Meanwhile, for all the optimal cases, NOx and soot emissions can meet the Euro VI limits. At low and mid loads, both the open and re-entrant type piston bowl can be equipped, while the high load only prefers the open type piston bowl for the DMDF mode. The re-entrant type or deep piston bowls are superior in organizing strong in-cylinder flow, which is beneficial for the fuel/air mixing. The open type or shallow piston bowls are helpful for reducing the heat transfer losses owing to the less heat transfer surface area. Furthermore, a correlation analysis was conducted to investigate the sensitivity of engine performance to the piston geometric parameters and injection parameters. It is concluded that the fuel injection event becomes more important for managing the engine performance as load increases. Among the injection parameters, the influence of the fuel injection timings and injection pressure on engine performance is more obvious. The piston geometric parameters play more significant roles in the heat transfer losses than the injection parameters for all loads. Among the geometric parameters, the most influential parameters are the width and open extent of the piston bowl. The heat transfer loss energy fraction can be well decreased with a wider and more open piston bowl., This work was partially supported by the National Natural Science Foundation of China (Grant Nos. 51961135105 and 91641117) and Postdoctoral Research Foundation of China (Grant Nos. 2019M661094 and 2020T130075). The experimental results used in this investigation were obtained in a project funded by VOLVO Group Trucks Technology. The authors also acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R) and the Universitat Politecnica de Val`encia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (PAID-06-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Clean and efficient dual-fuel combustion using OMEx as high reactivity fuel: comparison to diesel-gasoline calibration

  • Benajes, Jesús|||0000-0002-1653-9188
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Lago-Sari, Rafael
[EN] From previous results in a single-cylinder engine platform, it can be concluded that the dual-mode dual-fuel (DMDF) concept can be a potential solution to overcome the major constraints found with other single-fuel low temperature combustion modes. To extend these findings to a real application, this work evaluates the potential of the diesel-gasoline DMDF concept on a multi-cylinder 8L engine in terms of performance and emissions. To do this, a full engine calibration map was obtained following a specific methodology. The emissions results show that diesel-gasoline DMDF allows to achieve EURO VI NOx and soot emissions in a great portion of the engine map. Nonetheless, the levels of these pollutant at high load conditions exceed the EURO VI limits by far due to the need of implementing a diffusive combustion strategy with high EGR levels to avoid excessive in-cylinder pressure gradients. To mitigate this issue, the use of Oxymethylene ether (OMEx) instead of diesel fuel is proposed. A dedicated engine calibration was developed for the OMEx-gasoline DMDF concept following the same methodology. The results show that the oxygen content in the OMEx molecule allows to achieve a fully EUVI compliant engine calibration in terms of NOx with engine-out soot levels lower than 0.01 g/kWh. Moreover, due to the lower stoichiometric air-fuel ratio with this fuel, the air management system requirements are lower, reducing the pumping losses and increasing the brake thermal efficiency in most of the calibration map., The authors thanks ARAMCO Overseas Company and VOLVO Group Trucks Technology for supporting this research. The authors acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA201787694-R). The authors also acknowledge the Universitat Politecnica de Valencia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (SP20180148). The author R. Sari acknowledges the financial support from the Spanish ministry of science innovation and universities under the grant "Ayudas para contratos predoctorales para la formacion de doctores"(PRE2018085043).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Optimization of the parallel and mild hybrid vehicle platforms operating under conventional and advanced combustion modes

  • Benajes, Jesús|||0000-0002-1653-9188
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Martínez-Boggio, Santiago
[EN] The stringent regulations, increased global temperature and customer demand for high fuel economy have led to rapid developments of different alternative propulsion solutions in the last decade, with special attention to the electrified vehicles. The combination of electric machines with conventional powertrains allows to diversify the powertrain architectures. In addition, alternative combustion modes as reactivity controlled compression ignition (RCCI) have been shown to provide simultaneous ultra-low NOx and soot emissions with similar or better thermal efficiency than conventional diesel combustion (CDC). Therefore, the combination of both technologies creates a promising horizon to be implemented in commercial vehicles of the near future. In this work, experimental and numerical simulations were combined to study the potential of the parallel full hybrid electric vehicle (P2-FHEV) and mild hybrid vehicle (MHEV) to obtain lower fuel consumption and NOx emissions than a conventional powertrain in the Worldwide Harmonized Light Vehicles Cycle (WLTC). The hybrid vehicles are simulated with both CDC and diesel-gasoline RCCI combustion engines as power source. Each powertrain was optimized in terms of components (battery, electric motors...) capacity, internal combustion engine operative points, energy management strategy and gear ratios. The results show a significant fuel consumption reduction as the complexity of the hybrid system increases. The parallel architecture, which represents the most complex hybrid system tested in this work, allows obtaining a fuel consumption reduction of around 20% as compared to CDC. The dual-mode CDC-RCCI concept showed improvements in NOx and soot emissions with comparable values in terms of energy consumption and CO2 emissions than CDC. Additionally, the mild hybrid technology with the functionality of start-stop, torque assist and regenerative braking showed an acceptable balance between complexity and fuel consumption gain., The authors want to express their gratitude to General Motors Global Research & Development for providing the engine used to acquire the experimental data used in this investigation. The authors acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R). The authors also acknowledge the Universitat Politecnica de Valencia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigation (PAID-06-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Emissions reduction from passenger cars with RCCI plug-in hybrid electric vehicle technology

  • Benajes, Jesús|||0000-0002-1653-9188
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Martínez-Boggio, Santiago Daniel
[EN] Hybrid Electric Vehicles (HEVs) can be considered as a potential technology to promote the change from conventional mobility to e-mobility. However, the real benefits in terms of CO2 emissions depend on a great extent on their mode of use, vehicle design and electricity source. On the other hand, in the last few years, advanced combustion modes as Reactivity Controlled Compression Ignition (RCCI) showed great advantages in terms of NOx and soot emissions reduction. This paper has the purpose of assessing, through numerical simulations fed with experimental results, the potential of different hybrid vehicles when used together with a low temperature combustion mode. In particular, the dual-fuel Mild (MHEV), Full (FHEV) and Plug-in (PHEV) hybrid electric vehicles are tested and compared to the original equipment manufacturer (OEM) and the conventional dual-fuel powertrain, both no-Hybrid vehicles. The powertrains are optimized to meet the current European homologation legislation Worldwide Harmonized Light Vehicle Test Procedure (WLTP). After that, a deep analysis is performed in terms of performance and emissions. Lastly, a life-cycle analysis (LCA) is performed to evaluate the real potential of the different technologies. The results show that the PHEV has the highest benefits in terms of fuel consumption and engine-out emissions. With this technology, it is possible to achieve the 50 g/km CO2 target for the PHEVs with a medium battery size (15 kWh), while NOx and soot levels are under the Euro 6 limits. In addition, the RCCI technology shows great benefits to achieve the Euro 6 soot level for the other hybrid platforms. The LCA shows that the PHEVs can achieve 12% reduction of the total CO2 with respect to the FHEVs, and 30% with respect to the no-hybrid diesel platform., The authors acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R). The authors also acknowledge the Universitat Politecnica de Valencia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (PAID-06-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Effects of fuel injection parameters on premixed charge compression ignition combustion and emission characteristics in a medium-duty compression ignition diesel engine

  • Molina, Santiago|||0000-0001-7879-2421
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Villalta-Lara, David
[EN] From the different power plants, the compression ignition diesel engines are considered the best alternative to be used in the transport sector due to its high efficiency. However, the current emission standards impose drastic reductions for the main pollutants, that is, NOx and soot, emitted by this type of engines. To accomplish with these restrictions, alternative combustion concepts as the premixed charge compression ignition are being investigated nowadays. The objective of this work is to evaluate the impact of different fuel injection strategies on the combustion performance and engine-out emissions of the premixed charge compression ignition combustion regime. For that, experimental measurements were carried out in a single-cylinder medium-duty compression ignition diesel engine at low-load operation. Different engine parameters as the injection pattern timing, main injection timing and main injection fuel quantity were sweep. The best injection strategy was determined by means of a methodology based on the evaluation of a merit function. The results suggest that the best injection strategy for the low-load premixed charge compression ignition operating condition investigated implies using a high injection pressure and a triple-injection event with a delayed main injection with almost 15% of the total fuel mass injected., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: This investigation has been funded by VOLVO Group Trucks Technology. The authors also acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R) and the Universitat Politecnica de Valencia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (PAID-06-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Potential of using OMEx as substitute of diesel in the dual-fuel combustion mode to reduce the global CO2 emissions

  • Benajes, Jesús|||0000-0002-1653-9188
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Martínez-Boggio, Santiago Daniel
[EN] To achieve the targets of extreme low emissions values for the transport sector, several technologies emerged in the last few years. In this sense, advanced combustion modes as the dual-fuel low temperature combustion showed great advantages in terms of NOx and soot emissions reduction. At low and medium engine load, the operation is stable with virtually zero emissions. However, the exhaust gas recirculation rates at high load need to be increased to avoid excessive in-cylinder peaks, which leads to higher soot emissions. At these conditions, the use of non-sooting fuels as the oxymethylene dimethyl ethers (OMEx) allows avoiding the NOx-soot trade-off. In addition, the e-fuel consideration of the OMEx makes it suitable to reduce the global GHG emissions. This paper assesses the potential of using OMEx as high reactivity fuel to reduce the CO2 well-to-wheel emissions, and NOx and soot tailpipe emissions, in a medium-duty truck operating under dual-fuel combustion in transient conditions. The cargo mass was varied between 0% and 100% (18 ton) in the World Harmonized Vehicle Cycle. The tank-to-wheel analysis shows slightly higher CO2 production with OMEx-gasoline than with diesel-gasoline due to the ratio between the lower heating value and the carbon content. However, the well-to-wheel analysis shows the benefits of using OMEx to reduce the carbon dioxide footprint, which ranges from 13% (at full cargo mass) to 19% (at low cargo mass) compared to diesel-gasoline dual-fuel mode. This benefit is due to the large gains in terms of fuel production due to the carbon capture and the clean electric energy source necessary to produce the OMEx., The authors acknowledge FEDER and Spanish Ministerio de Economía y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R). The authors also acknowledge the Universitat Politècnica de València for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigación (SP20180148)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Octane number influence on combustion and performance parameters in a Dual-Mode Dual-Fuel engine

  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Villalta-Lara, David
  • Lago-Sari, Rafael
[EN] Low temperature combustion stands as a promising alternative to realize low soot and NOx emissions while achieving fuel consumption benefits compared to the conventional diesel combustion. Nonetheless, its applicability is limited to narrow zones inside the engine map, reducing the potential benefits on a real driving case. In this scenario, the use of dual-mode dual-fuel combustion stands as an alternative to cover engine conditions up to full load, avoiding the constraints of the fully premixed combustion whenever is needed. This combustion concept is strongly influenced by the characteristics of the fuels that are used to create the charge stratification during the engine operation. The current research aims to evaluate the influence of the low reactivity fuel octane number on the combustion process and the average performance and emissions results. Additionally, the best octane number was determined by means of a merit function evaluation. Octane values of 100, 92.5, 87.5, 85 and 80 were obtained by blending iso-octane and heptane. Their performance was assessed in a medium-duty multi-cylinder platform at different representative operating conditions. The results suggest that fuels with octane number lower than 92.5 have a low impact at low load conditions. However, as load is increased, the high reactivity of the low research octane number fuels leads to early combustion processes, demanding settings modifications to avoid the appearance of excessive pressure gradients. As a consequence of these modifications, the fuel consumption and soot emissions increase. In general, RONs from 92.5 to 87.5 are less penalized, presenting the best merit function values, and therefore being the best fuels to be used in the hardware under investigation., The authors thanks VOLVO Group Trucks Technology and ARAMCO Overseas Company for supporting this research. The authors also acknowledge FEDER and Spanish Ministerio de Economía y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R) and the Universitat Politècnica de València for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigación (PAID-06-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental investigation on RCCI heat transfer in a light-duty diesel engine with different fuels: Comparison versus conventional diesel combustion

  • Olmeda, P.|||0000-0002-3161-0165
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Lago-Sari, Rafael
[EN] Reactivity controlled compression ignition (RCCI) combustion has demonstrated to be able to avoid the NOx-soot trade-off appearing during conventional diesel combustion (CDC), with similar or better thermal efficiency than CDC under a wide range of operating conditions. The high thermal efficiency of RCCI is explained by the combination of a short-duration and well-phased combustion process, which maximizes the fuel-to-work conversion efficiency, together with relatively low combustion temperatures, which increases the specific heat ratio during expansion and reduces thermal gradients for heat transfer losses. The objective of this work is to study the RCCI heat transfer characteristics and compare them to those of the CDC regime. To do this, a single-cylinder light-duty research engine instrumented with 25K-type thermocouples distributed among the cylinder head and cylinder liner is used. First, the influence of some engine settings on the RCCI heat transfer phenomenon is explored by means of parametric sweeps. Later, the RCCI heat transfer characteristics are compared for two different low reactivity fuels (LRF), gasoline and E85. Finally, the heat transfer characteristics of RCCI and CDC combustion regimes are compared at some representative operating points in matched load conditions. The results show that both LRF tested are suitable to be used in RCCI giving similar results in terms of energy usage. Moreover, the ability of RCCI combustion in exploiting the fuel energy to extract useful work is demonstrated, reducing by 13% the heat transfer versus CDC., The authors gratefully acknowledge General Motors Global Research & Development for providing the engine used in this investigation. The authors also acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Performance of a conventional diesel aftertreatment system used in a medium-duty multi-cylinder dual-mode dual-fuel engine

  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Villalta-Lara, David
  • Lago-Sari, Rafael
[EN] Dual-mode dual-fuel combustion stands as one of the promising techniques to allow the dual-fuel operation along the whole engine map. This concept relies on using different combustion strategies as reactivity controlled compression ignition up to medium load, then migrating to diffusive dual-fuel combustion to reach full load. With this strategy, it is possible to obtain sensible reductions in NOx and soot while providing improvements in fuel consumption and CO2 emissions. However, the excessive quantities of HC and CO together with the low exhaust temperature can compromise the diesel oxidation catalyst (DOC) efficiency. In addition, the diffusive dual-fuel combustion applied at high engine load produces considerable soot amounts that should be reduced within the diesel particulate filter (DPF). Based on these facts, this work intends to evaluate the efficiency of a commercial aftertreatment system (DOC¿+¿DPF) while operating in dual-mode dual-fuel combustion. Additionally, fundamental studies where developed to understand the impact of the combination of fuels on the exhaust hydrocarbon species. First, the DOC performance was evaluated at steady-state and transient conditions under different operating conditions fulfilling the EUVI NOx and soot limits. In parallel, the different engine-out hydrocarbon species were measured by means of a Fourier-transform infrared spectroscopy (FTIR) gas analyzer. Finally, the passive and active regeneration processes were assessed by means of different methodologies aiming to evaluate the low NOx-low soot interaction and the capability of the active regeneration in dual-fuel dual-mode (DMDF) operating conditions. The DOC results showed an improper conversion efficiency at low load operating condition, where the exhaust temperature is low. By contrast, the thermal inertia at transient conditions allowed to improve the DOC behavior at low load, reaching DOC-out emissions one order of magnitude lower than those from the steady-state tests. Concerning the DPF, it was demonstrated that the low concentration of NOx and soot produced during the combustion does not lead to sensible changes in the NO2/NOx ratio before and after the DPF, indicating a low level/absence of passive regeneration. In the case of the active regeneration, both conventional diesel combustion (CDC) and DMDF operating conditions can obtain satisfactory reduction in the total soot trapped, being the increase in the exhaust temperature consequence of the HC and CO conversion the supporting mechanism for the active regeneration in the DMDF concept., The authors thanks VOLVO Group Trucks Technology and ARAMCO Overseas Company for supporting this research. The authors also acknowledge FEDER and Spanish Ministerio de Economía y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

OMEx-diesel blends as high reactivity fuel for ultra-low NOx and soot emissions in the dual-mode dual-fuel combustion strategy

  • García Martínez, Antonio|||0000-0001-5783-4936
  • Gil, A.|||0000-0001-7192-6992
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Lago-Sari, Rafael
[EN] Previous works demonstrated that the use of Oxymethylene ether (OMEx) in advanced combustion modes, as the dual-mode dual-fuel combustion, leads to a notable reduction of the lifecycle CO2 emissions while promoting lower NOx and soot emissions than those from conventional diesel combustion. Nonetheless, the low heating value of OMEx results in a fuel consumption increase. A possible solution to avoid this drawback is by blending OMEx with diesel fuel. This will help to introduce the OMEx in the market with minimum changes in the infrastructure. In this context, this work evaluates the impact of using OMEx-diesel blends in different mass percentages (50% and 70% of OMEx in diesel), compared to the reference net fuels (net diesel and OMEx) in a multi-cylinder compression ignition engine operating under dual-mode dual-fuel combustion at different engine loads (25%, 50%, 80% and 100%) and 1800 rpm. At each condition, an air mass sweep was performed to assess the limiting operating conditions with each fuel due to either excessive pressure gradients and soot production, or low combustion efficiency. The results suggested that the OMEx-diesel blends allow to reduce the soot emissions compared to net diesel for all the conditions tested. In addition, blends having an OMEx mass content greater than 70% allowed to fulfill the EUVI limits for NOx with ultra-low soot levels (< 0.01 g/kWh) up to 80% engine load. Nonetheless, the unique fuel able to achieve the EUVI limit for NOx with zero soot emissions simultaneously at 100% of engine load was found to be the pure OMEx., The authors thanks ARAMCO Overseas Company and VOLVO Group Trucks Technology for supporting this research. The authors acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R). The authors also acknowledge the Universitat Politecnica de Valencia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (PAID-06-18). The author R. Sari acknowledges the financial support from the Spanish ministry of science innovation and universities under the grant "Ayudas para contratos predoctorales para la formacion de doctors" (PRE2018-085043).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Potential of e-Fischer Tropsch diesel and oxymethyl-ether (OMEx) as fuels for the dual-mode dual-fuel concept

  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Villalta-Lara, David
  • Lago-Sari, Rafael
  • Gordillo Zavaleta, Victor
  • Gaillard, Patrick
[EN] The dual-mode dual-fuel combustion strategy allows operating over the entire engine map by implementing a diffusive dual-fuel combustion at high engine loads. This requires increasing the amount of exhaust gas re-circulation to control the NOx emissions, which penalizes the soot levels. At these conditions, the use of nonsooting fuels as the e-Fischer Tropsch Diesel (e-FT) and oxymethylene dimethyl ethers (OMEx) could be a potential way to avoid the NOx-soot trade-off. The experimental results acquired in a compression ignition multi-cylinder medium-duty engine evidence that the higher oxygen content of OMEx allows reducing the soot emissions at high loads to near zero levels, while e-FT promotes a soot reduction of around 20% as compared to diesel. Nonetheless, the low lower heating value of OMEx leads to excessive injection durations, enlarging the combustion process and increasing the fuel consumption around 1.3-7.2% and 1.4-5.3% as compared to diesel and e-FT, respectively, depending on the engine load. Finally, the well to wheel analysis confirms the potential in reducing the carbon dioxide footprint of OMEx (14.8-69%) and e-FT (0.3-38.5%) compared to diesel, as they can be synthetized via direct air capture as a source of carbon and using renewable energy., The authors thanks VOLVO Group Trucks Technology and Aramco Overseas Company for supporting this research. The authors also acknowledge FEDER and the Spanish Ministerio de Economia y Competitividad for partially supporting this research through the TRANCO project (TRA2017-87694-R), and the Universitat Politecnica de Valencia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (PAID-06-18)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Performance and emissions of a series hybrid vehicle powered by a gasoline partially premixed combustion engine

  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Lago-Sari, Rafael
  • Dimitrakopoulos, Nikolaos
  • Turnér, Martin
  • Tunestål, Per
[EN] This work evaluates the performance and emissions of the series hybrid vehicle concept powered by a gasoline partially premixed internal combustion engine. To do so, experimental data was collected from a Volvo VED-D4 Euro 6 four-cylinder compression ignition engine running under gasoline partially premixed combustion. Two series hybrid vehicle models were developed in GT-Power (R), which were fed with the experimental data to evaluate the potential of the hybrid concept. First of all, the battery charging strategy of the hybrid vehicles was optimized in terms of number of power levels and operating conditions. For this, a design of experiments was performed in GT-Power (R), which enabled to obtain a predictive model of the performance and emissions. The predictive model was used to obtain the optimized NOx-fuel consumption Pareto frontiers for each charging strategy proposed. Finally, the GT-Power (R) vehicle models were run with the optimal operating conditions (selected from each Pareto) in both the new European driving cycle and worldwide harmonized light vehicles test cycle. The results show that the hybrid powertrain running with partially premixed combustion is able to achieve similar or better performance than the commercial diesel vehicle with low engine-out emissions. Moreover, comparing the results from both vehicles, it was confirmed that the hybridization results in better improvements when applied to urban traffic than for highway conditions where the power request is higher and the potential for regenerative braking is reduced., The authors gratefully acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R). The authors also gratefully acknowledge the KCFP Engine Research Center (Swedish Energy Agency grant number 22485-4) for partial support of this research.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

High efficiency two stroke opposed piston engine for plug-in hybrid electric vehicle applications: evaluation under homologation and real driving conditions

  • Serrano, J.R.|||0000-0003-0692-3917
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Martínez-Boggio, Santiago Daniel
[EN] The potential of plug-in hybrid electric vehicles (PHEV) to reduce greenhouse gas emissions highly depends on the vehicle usage and electricity source. In addition, the high costs of the battery pack and electric components suppose a challenge to the vehicle manufacturers. However, the internal combustion engine complexity can be reduced due to its lower use as compared to the no-hybrid vehicles. This work evaluates the use of a new opposed piston 2-stroke engine, based on rod-less innovative kinematics, in a series PHEV architecture based on rod-less innovative kinematics along different driving routes in Europe. A 0D-vehicle model fed with experimental tests is used. The battery size is optimized under homologation conditions for two different vehicle types. The optimum case is tested in several real driving conditions under different vehicle modes and battery states of charge. The main contribution of this work is the demonstration of the potential to reduce the vehicle CO2 emissions and cost with an innovative 2-stroke engine. The results show that 24 kWh is the optimum battery size for both vehicle platforms. Charge depleting mode shows 70% of CO2 tailpipe reduction in urban cycles and 22% in long travels compared to the no-hybrid version. Charge sustaining mode results show a CO2 tailpipe reduction of 20% in urban cycles and 2% in long distance travels with respect to the no-hybrid version. In spite of the CO2 contribution of the battery manufacturing, the results show a reduction of LCA CO2 emissions in 52% in charge depleting and 7% charge sustaining against the no-hybrid case., This work has been partially supported by "Conselleria de Innovacion, Universidades, Ciencia y Sociedad Digital de la Generalitat Valenciana" through grant number GV/2020/017. The authors acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R). The authors want to thank INNengine for providing the engine and the help in the experimental campaign. Lastly, acknowledge to Gamma Technologies for the numerical simulation support and provide the GT-RealDrive licenses
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Dual fuel combustion and hybrid electric powertrains as potential solution to achieve 2025 emissions targets in medium duty trucks sector

  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Martínez-Boggio, Santiago Daniel
  • Gaillard, Patrick
  • Poussin, Olivier
  • Amer, Amer A.
[EN] The European commission is targeting a 15% reduction in CO2 emissions for medium and heavy-duty transportation starting in 2025. Moreover, the next European normative (EU VII) will impose a decrease of 50% for NOx and particulate matter emissions with respect to the current EUVI normative. Meeting these requirements pose a significant challenge to truck and bus manufacturers. Several proposals appeared in the last few years as improve the cabin aerodynamics, decrease the friction losses and improve the powertrain efficiency. The last point involves improving the current combustion systems as well as the transmission and energy management. This work proposes to couple two potential technologies to reduce at the same time the global (CO2) and local pollution (NOx and soot). For this, two truck platforms representative of medium-duty applications (18 ton and 25 ton) are tested using the reactivity controlled compression ignition (RCCI) combustion mode with diesel and gasoline as fuels. In addition, the trucks are electrified to full hybrid technology in a parallel pre-transmission (P2) architecture. A 0D vehicle numerical model is used to evaluate the trucks under four different driving cycles representative of homologation and real driving conditions. The numerical model is validated against on road measurements. The RCCI combustion is modeled by means of a map-based approach with 54 points measured in steady-state conditions. This work presents a complete engine map calibration with measurements up to 350 hp using two combustion modes inside the map (so-called dual-mode dual-fuel). As a baseline, the commercial diesel no-hybrid trucks and the dual-fuel no-hybrid trucks are used. The results show the potential of the dual-mode dual-fuel combustion to achieve ultra-low NOx and soot emissions. In addition, the CO2 target reduction is achieved for several truck platforms and driving conditions due to the hybridization of the driveline. The cycles with large phases of urban driving are the most favorable due to the ability of recovering energy by means of the regenerative braking system and the possibility to avoid large idling phases with respect to the no-hybrid versions. In addition, the decrease of the payload improves the CO2 reduction with respect to the baseline cases., The authors thanks ARAMCO Overseas Company and VOLVO Group Trucks Technology for supporting this research. The authors acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R). The authors also acknowledge the Universitat Polit`ecnica de Val`encia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (PAID-06-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Exploration of suitable injector configuration for dual-mode dual-fuel engine with diesel and OMEx as high reactivity fuels

  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Sanchis, Enrique José|||0000-0002-6856-8992
  • Fogué-Robles, Álvaro
[EN] Dual-mode dual-fuel (DMDF) combustion stands over other low temperature combustion strategies as it is able to operate over the entire engine map by transitioning between reactivity controlled compression ignition and diffusive combustion depending on the engine load. In combination with non-sooting e-fuels, it is able to achieve low NOx and soot levels even at high loads. Oxygenated fuels like poly-oxymethylene dimethyl ethers (OMEx) have been already proved to present an outstanding NOx-Soot trade-off improvement when used in combination with a DMDF combustion strategy. One drawback of OMEx is that, despite having a high reactivity, it has a low lower heating value, which requires considerably longer injection events compared to other traditional fuels in order to achieve the same engine power output. The long injections limit the flexibility of the injection strategy and result in extremely long combustion durations. A possible solution to this problem resides in moving towards injectors with higher flow rate capacities, but this may compromise the mixing and combustion processes. This work aims to shed some light on the implications of changing the engine hardware to overcome this limitation by testing a DMDF mull-cylinder engine using gasoline as the low-reactivity fuel and diesel or OMEx as the high reactivity fuels with injectors of different flow capacity. The results show that a concise analysis of the involved phenomenology of the combustion process allows to find out the trade-off between the engine-out emissions and the mixing capacity of the injection system while the engine performance is not significantly affected., The authors thanks VOLVO Group Trucks Technology and ARAMCO Overseas Company for supporting this research. The authors also acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R) and the Universitat Politecnica de Valencia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (PAID-06-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Potential of hybrid powertrains in a variable compression ratio downsized turbocharged VVA Spark Ignition engine

  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Martínez-Boggio, Santiago Daniel
  • Wittek, Karsten
[EN] After the diesel emissions scandal, also known as Dieselgate, Direct Injection Spark-Ignited (DISI) internal combustion engines (ICE) appears as the most promising alternative to mitigate the harmful tailpipe emissions from passenger cars. In spite of that, the current ICE technologies are not enough to achieve the fuel consumption/CO2 emissions targets set by the new transportation legislation (4.1 L-gasoline/100 km, 95 gCO(2)/km for 2021). In this complex scenario, the electrification of the powertrain using high efficiency electric motors and battery package together with sophisticated DISI engines appears as potential solution to meet these requirements. The aim of this work is to study the fuel consumption and pollutant emissions in transient conditions from a passenger car equipped with a variable compression ratio (VCR) DISI engine and electrified powertrain technologies. The vehicle behavior was simulated by means of a 0D GT-Suite model fed by experimental results obtained in an engine test bench. Mild hybrid electric vehicle (MHEV) and full hybrid electric vehicle (FHEV) architectures using a VCR DISI engine were studied. Moreover, an optimization methodology is presented to select the best vehicle configuration in terms of hardware and control strategies by means of a design of experiments (DoE). The results show that VCR allows a fuel improvement of 3% with respect to the conventional DISI fixed CR along the worldwide harmonized light vehicles test cycles (WLTC). The benefits found when combining the VCR technology with hybrid powertrains are even higher. In this sense, the fuel improvements were higher as the electrification levels increased, with 8% for MHEV-VCR and around 20% for FHEV-VCR. In terms of emissions, the two clear benefits with FHEV-VCR were the reduction of particle number (PN) and unburned hydrocarbons (HC) of around 60% and 15%, respectively, as compared to the conventional DISI., The authors acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R). The authors also acknowledge the Universitat Politecnica de Valencia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (SP20180148).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Fuel sensitivity effects on dual-mode dual-fuel combustion operation for different octane numbers

  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Villalta-Lara, David
  • Lago-Sari, Rafael
[EN] The dual-mode dual-fuel combustion is a promising combustion concept to achieve the required emissions and carbon dioxide reductions imposed by the next emissions standards. Nonetheless, since the combustion concept relies on the reactivity of two different fuels (diesel and gasoline), the fuel formulation requirements are stricter. This work investigates the effects of the low reactivity fuel sensitivity for different octane numbers at different operating conditions representative of the combustion regimes found inside the dual-mode dual-fuel engine map. For this, experimental evaluations were performed using fuels with research octane number 92.5 and 80 and different sensitivities (0, 5 and the maximum one achievable for each fuel). The combustion development was assessed by means of the heat release rate characterization. Moreover, numerical simulations in a constant volume homogeneous reactor were used to explore and understand the impact of the different fuels on the ignition delay time. The results suggest that the sensitivity increase affects the different research octane number fuels in a different way. For the fuel with research octane number 92.5, the sensitivity variation increases the experimental ignition delay, impairing the combustion process and increasing the fuel consumption. In the case of the fuel with research octane number 80, the sensitivity increase does not affect the combustion development. This was justified by the numerical investigation, which points to a wider temperature range where the sensitivity does not affect the final ignition delay for research octane number 80. Moreover, generally, the ignition delay times for research octane number 80 considering the experimental gasoline fraction used are half than those of research octane number 92.5. At full load conditions, the trend is inverted, where the experimental ignition delay for research octane number 80 is affected by the sensitivity whilst research octane number 92.5 presents only modifications after the combustion start., The authors thanks ARAMCO Overseas Company and VOLVO Group Trucks Technology for supporting this research. The authors also acknowledge FEDER and Spanish Ministerio de Economía y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R), and the Universitat Politècnica de València for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigación (PAID-06-18).